Makita N900の取扱説明書

12ページ 0.61 mb
ダウンロード

ページに移動 of 12

Summary
  • Makita N900 - page 1

    Angle Grinder No load speed Overall length Net weight (RPM) 100 mm (4”) MODEL N900 Spindle thread INSTRUCTION MANUAL 10,000 1 255 mm (10”) 1 1.5 kg (3.3 lbs) 1 MlOx 1.25 Manufacturer reserves the right to change specifications without notice. Note: Specifications may differ from country to country. WARNING: For your personal safety, READ and UN ...

  • Makita N900 - page 2

    IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. 2. CONSIDER WORK AREA ENVIRONMENT. ...

  • Makita N900 - page 3

    14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don't carry tool with finger on switch. Be sure switch is OFF when plugging in. 16. EXTENSION CORDS. Make sure your extension cord is in good condition. When using ...

  • Makita N900 - page 4

    VOLTAGE WARNING: Before connecting the tool to a power source (receptacle, outlet, etc.) be sure the voltage supplied is the same as that specified on the nameplate of the tool. A power source with voltage greater than that specified for the tool can result in SERIOUS INJURY to the user - as well as damage to the tool. If in doubt, DO NOT PLUG IN T ...

  • Makita N900 - page 5

    Installing side grip (auxiliary handle) Screw the same grip on the tool securely. Installing or removing depressed center wheel CAUTION: Always be sure that the tool is switched off and unplugged before installing or removing the wheel. Screw the inner flange onto the spindle. Fit the wheel on over the inner flange and screw the lock nut onto the s ...

  • Makita N900 - page 6

    To tighten the lock nut, hold the spindle with the wrench so that it cannot revolve, then use the lock nut wrench and securely tighten clockwise. Lock nut wenc If -wrench CAUTION: Use only the Makita wrench and lock nut wrench provided to install or remove the wheel. Failure to do so may result in overtightening or insufficient tightening of the l ...

  • Makita N900 - page 7

    Operation Hold the tool firmly. Turn the tool on and wait until the wheel or disc attains full speed. Then apply the wheel or disc to the work- piece. In general, keep the edge of the wheel or disc at an angle of about 15' to the work- piece surface. During the break-in period with a new wheel, do not work the grinder in the B direction or it ...

  • Makita N900 - page 8

    MAINTENANCE CAUTION: Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. To maintain product SAFETY and RELIABILITY, repairs, carbon brush inspection and replace- ment, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using ...

  • Makita N900 - page 9

    ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. Part No. @Wheel cover Part No. 344257-6 Grit Wh ...

  • Makita N900 - page 10

    @Abrasive discs Grit 741404-OBP AC46 Part No. Size lmm) 742036-0-3 742037-8-3 Wheels 10 per Pkg. 742038-6-3 @Cut-off wheel @Lock nut 10 - 30 (For abrasive disc) Part No. 224501-6 @Wire cup brush 75 Part No. 743201-4 @Wire bevel brush 85 Part No. 743203-0 @Grip holder Part No. 164329-9 @Wheel guard assembly (For cut-off wheel) Part No. 122363-5 @Fle ...

  • Makita N900 - page 11

    100 mm (4") ANGLE GRINDER Model N900 Note: The switch and other part configurations may differ from country to country. 11 ...

  • Makita N900 - page 12

    MACHINE ~ 16 17 18 19 20 21 22 24 25 26 27 28 29 E02 E03 1 1 1 2 1 1 1 1 1 1 1 1 6 1 1 0 Ring 11 Needle Bearing 810 Rstainmg Ring S- 12 Spiral Bevel Gear 36 Ball Bearing 6201LB Flat Washer 12 Spindle Wheel Cover Pan Head Screw M5x20 IWith Washer) Inner Flange 30 Lock Nut 10-30 Woodruff Key 3 Spiral Bevel Gear 11 Ball Bearing 6WOLB Fan 52 10 11 12 1 ...

メーカー Makita カテゴリー Grinder

Makita N900のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- N900の取扱説明書
- Makitaの製品カード
- パンフレット
- またはMakita N900の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Makita N900の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Makita N900の取り付け説明書、サービスマニュアル、簡易説明書、またはMakita N900のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Makita N900の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Makita N900デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがMakita N900を使用するのを助ける技術的文書のことです。説明書は通常、全てのMakita N900ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Makitaの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Makita N900の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははMakita N900の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Makita N900に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Makita N900デバイスの基本機能を使うにあたってのヒント。 Makita N900のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Makita N900に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるMakita N900のメーカー/サービスへの連絡先に関する情報。

Makita N900についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもMakita N900の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがMakita N900で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)