-
Husqvarna SOFF-CUT 150 - page 1
HUSQV ARNA CONSTRUCTION PRODUCTS Soff-Cut 150 Please read the operator’ s manual carefully and make sur e you understand the instructions before using the machine. GB Oper a tor’ s manual ...
-
Husqvarna SOFF-CUT 150 - page 2
CONTENTS Content Page T able of contents ………………………….. 2 Unpacking .................................................. 2 T ransporting ............................................... 2 Sound Data ................................................ 2 I ntroduction, personal safety ...................... 3 Registration of the product ? ...
-
Husqvarna SOFF-CUT 150 - page 3
INTRODUCTION Common sense: The focus of this manual is HOW to operate and service the equipment safely . It is not possible to cover every conceivable situation you can face when using this equipment. Therefore use this product only in a manner described in this manual. Operation or handling the machine in any other manner can lead to serious injur ...
-
Husqvarna SOFF-CUT 150 - page 4
4 REGISTER THE PRODUCT Please register your new 150 with Husqvarna Construction Products by mailing in the registration card that came with the machine or you can register on the internet site www .husqvarnawarranty .com Registration will allow us to contact in case of any critical updates or recalls on this machine. W arranty registration has also ...
-
Husqvarna SOFF-CUT 150 - page 5
5 SAFETY W ARNINGS W ARNING Failure to comply with the following warnings could result in serious bodily injury or death! PERSONAL SAFETY • Read and understand instructions before operating saw . • Always wear safety approved hearing, eye, head and respiratory protection. • Wear boots with non-slip soles to provide proper footing. Steel-toed ...
-
Husqvarna SOFF-CUT 150 - page 6
6 EXCEL SERIES BLADES The Excel Series of diamond blades have been designed specically for the Soff-Cut Ultra Early Entry dry cutting system of green concrete. These specialty blades are designed to increase speed and life while cutting a wide range of aggregates. Choose the correct specication of diamond blade for your area as follows: Purpl ...
-
Husqvarna SOFF-CUT 150 - page 7
WHA T IS WHA T D C E B A J F What is what? A. Oil dipstick or ll B. Oil drain C. Fuel shut of f lever D. Choke lever E. Throttle lever F . Starter rope G. Air cleaner H. Fuel tank J. Engine on/off switch Model number and serial number 7 G H H A ...
-
Husqvarna SOFF-CUT 150 - page 8
8 OPERA TING INSTRUCTIONS Experience is very important when running the 150 saw . A skilled worker is highly recommended. Always do an inspec- tion of the saw before starting the engine. Check the fuel (H) and oil level (A) per the enclosed engine manual. SAE 10W/30 oil and unleaded gasoline with an 87 or higher octane should be used. Observe all s ...
-
Husqvarna SOFF-CUT 150 - page 9
9 FUEL HANDLING PROPER FUEL T aking the following precautions will lessen the risk of injury and property damage: - Use extreme care in handling gasoline. It is extremely ammable and the vapors are explosive. - Extinguish all cigarettes, cigars, pipes, and other sources of ignition. - Use only approved gasoline containers. - Never remove gas cap ...
-
Husqvarna SOFF-CUT 150 - page 10
10 Engine Oil Checking, Adding and Changing Oil Check the engine oil level (A) daily with saw fully lowered and the engine level. See the enclosed Robin manual for more details. Use SAE 10W-30 viscosity detergent automotive type with API service class SE or higher grade oil. Note: Engine holds approximately 0.6 quart (0.6 liter) when changing oil a ...
-
Husqvarna SOFF-CUT 150 - page 11
11 As concrete hydrates or cures and begins to set, it develops internal stresses which may cause random cracks. Random cracks cast doubt on the quality and workmanship of the concrete. Contraction joints are cut in concrete to relieve these stresses before they seek their own relief in the form of random crack. The Sof f-Cut Ultra Early Entry syst ...
-
Husqvarna SOFF-CUT 150 - page 12
12 “ The timing of concrete operations - especially nishing and jointing - is critical” , states a quote from the foreword of the American Concrete Institute (ACI) 302.1 R-96. It goes on to say that “Failure to address this issue can contribute to unde- sirable characteristics in the wearing surface as cracking...” (It mentions other pro ...
-
Husqvarna SOFF-CUT 150 - page 13
13 TROUBLESHOOTING ENGINE WILL NOT ST ART - Check if there is fuel in the tank and it is the correct fuel. Make sure there is no water in the fuel. - Check if the fuel valve is turned to the “on” position. - Check if the kill switch is in the “on” position. - Check that the spark plug wire is connected to the spark plug. - Engine is oode ...
-
Husqvarna SOFF-CUT 150 - page 14
TECHNICAL SPECIFICA TIONS Engine Model Robin EX 13 Engine oil volume, quarts/liters 0.6/0.6 Gasoline tank volume, gal/liters 0.7/2.7 T ype Air cooled, 4-cycle, single slant cylinder , overhead camshaft, gasoline engine Air fi lter Cyclonic type Oil system Oil alert with auto shut down sensor Muf fl er Silent type 75 dbA, exhaust de fl ector , sp ...
-
Husqvarna SOFF-CUT 150 - page 15
15 W ARRANTY HUSQV ARNA EQUIPMENT W ARRANTY New 150 sold by Husqvarna Construction Products are warranted to be free from manufacturing defects in normal service for a period of six (6) months for labor and up to one (1) year on parts from date of purchase by the original consumer purchaser or date of introduction into rental company eet. Our ob ...
-
Husqvarna SOFF-CUT 150 - page 16
1 153478-26 2009-12-29 w ww .hu sqvarnacp .com ´®z+UOr¶6h¨ ´®z+UOr¶6h¨ Original instructions ...
Husqvarna SOFF-CUT 150についてご質問がありますか?
次のフォームを使用してください
見つけた説明書を読んでもHusqvarna SOFF-CUT 150の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがHusqvarna SOFF-CUT 150で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。