DeWalt DW708の取扱説明書

21ページ 1.08 mb
ダウンロード

ページに移動 of 21

Summary
  • DeWalt DW708 - page 1

    ...

  • DeWalt DW708 - page 2

    D E WALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286 Printed in U.S.A. (MAR01-CD-1) Form No. 386762-02 DW708 Copyright © 2001 ...

  • DeWalt DW708 - page 3

    INSTRUCTION MANUAL GUIDE D'UTILISA TION MANUAL DE INSTRUCCIONES DW708 Sliding Compound Miter Saw DW708 Scie à onglets mixtes coulissants DW708 Sierra de ángulo compuesto (ingleteadora) corrediza INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO. Before r etur ...

  • DeWalt DW708 - page 4

    English D E W AL T… BUIL T JOBSITE TOUGH D E WALT high performance industrial tools are made for America’s toughest industrial and construction applications. The design of every tool in the line – from drills, to sanders, to grinders – is the result of rigorous use on jobsites and throughout the industry. Each tool is produced with painstak ...

  • DeWalt DW708 - page 5

    SAFETY INSTRUCTIONS ...................................................................................................2 ADDITIONAL SAFETY RULES............................................................................................2 DOUBLE INSULATION/POLARIZED PLUG .................................................................2 EXTENSION CO ...

  • DeWalt DW708 - page 6

    English 2 Important Safety Instructions for all tools. WARNING: For your own safety read instruction manual before operating sliding compound miter saw. WARNING: When using electric tools, basic safety precautions should always be followed to reduce risk of fire, electric shock, and personal injury, including the following: Double Insulation Double ...

  • DeWalt DW708 - page 7

    3 English • DO-Keep hands out of path of saw blade. • DO-Shut off power, disconnect cord from power source and wait for saw blade to stop before servicing or adjusting tool. • DO-Support long work with an outboard tool rest. • DON’T-Attempt to operate on anything but designated voltage. • DON’T-Operate unless all clamp handles are tig ...

  • DeWalt DW708 - page 8

    Electrical Connection Be sure your power supply agrees with the nameplate marking. AC ONLY means that your saw will operate on alternating current only. A voltage decrease of 10 percent or more will cause a loss of power and overheating. All D E WALT tools are factory tested. If this tool does not operate, check the power supply. Unpacking Y our Sa ...

  • DeWalt DW708 - page 9

    FIG.3 5 English FIG. 4 CAPACITY OF CUT 50 ° miter left, 60 ° miter right 48 ˚ bevel left and right US Models Non-US Models Miter Bevel Max Max Max Max Height Width Height Width ____ _____ ______ _____ ______ _____ 0 ° 0 ° 4.3" 12" 4.3" 12" 45 L&R ° 0 ° 4.3" 8.5" 4.3" 8.5" 0 ° 45 ° L 3.2" 12& ...

  • DeWalt DW708 - page 10

    6 Descript. Teeth of Cut Fine Trim Precision 60-100 Very Molding Ground Smooth Carbide Splinter Free Trim, Framing, Combination 32-60 Smooth Pressure Multi-Purpose Fast Cut Treated Decking Aluminum Non-Ferrous 60-80 — Metal Cutting Negative Rake Teeth Stabilizer Your saw includes one base stabilizer. This must be installed before using your saw. ...

  • DeWalt DW708 - page 11

    7 English Adjustments PERFORM ALL ADJUSTMENTS WITH THE SLIDING COMPOUND MITER SAW UNPLUGGED. NOTE: Your sliding compound miter saw is fully and accu- rately adjusted at the factory at the time of manufacture. If readjustment due to shipping and handling or any other reason is required, follow the steps below to adjust your saw. Once made, these adj ...

  • DeWalt DW708 - page 12

    8 in place, and gently move the pointer left or right. Retighten the screw after setting the pointer to 0 ° . Adjusting the bevel stop to 45° left or right NOTE: Adjust the 45 ° bevel angles only after performing the 0 ° bevel angle adjustment. To adjust the left 45 ° bevel angle, loosen the bevel lock handle and tilt the head to the left. If ...

  • DeWalt DW708 - page 13

    your own safety by giving the saw your complete attention. RAIL GUIDE ADJUSTMENT Periodically check the rails for any play or clearance. The top rail can be adjusted with the two right set screws shown in Figure 17. To reduce clearance, rotate the set screws clock- wise gradually while sliding the saw head back and forth. Reduce play while maintain ...

  • DeWalt DW708 - page 14

    10 MAKE DRY RUNS (UNPOWERED) BEFORE FINISH CUTS SO THAT YOU CAN CHECK THE PATH OF THE BLADE. DO NOT CROSS HANDS. Keep both feet firmly on the floor and maintain proper balance. As you move the miter arm left and right, follow it and stand slightly to the side of the saw blade. Sight through the guard louvers when following a pencil line. CLAMPING T ...

  • DeWalt DW708 - page 15

    11 English VERNIER SCALE Your saw is equipped with a vernier scale for added precision. The vernier scale allows you to accurately set miter angles to the nearest 1/4 degree. To use the vernier scale follow these steps. (As an example, assume that the angle you want to miter is 24-1/4 degree right). 1. Turn off sliding compound miter saw. 2. Set th ...

  • DeWalt DW708 - page 16

    12 CUTTING BASE MOLDING UP TO 4-1/4" (108 mm) HIGH VERTICALLY AGAINST THE FENCE Position molding as shown in Figure 26. All cuts made with the back of the molding against the fence and bottom of the molding against the base. INSIDE CORNER: Left side 1. Miter left 45 ° 2. Save left side of cut Right side 1. Miter Right 45 ° 2. Save right side ...

  • DeWalt DW708 - page 17

    1. Position molding with top of the molding resting on the base of the saw 2. Miter left 45 ° 3. Save left side of cut OUTSIDE CORNER: Left side 1. Position molding with bottom of molding against the base of the saw 2. Miter right 45 ° 3. Save left side of cut NOTE: If the cut must be made somewhere other than 1" (25.4mm) from the end of the ...

  • DeWalt DW708 - page 18

    TABLE 1 COMPOUND MITER CUT (POSITION WOOD WITH BROAD FLAT SIDE ON THE TABLE AND THE NARROW EDGE AGAINST THE FENCE) SET THIS MITER ANGLE ON SAW ANGLE OF SIDE OF BOX (ANGLE A) SQUARE BOX 6-SIDED BOX MITER DEGREE SETTING BEVEL DEGREE SETTING SET THIS BEVEL ANGLE ON SAW INSTRUCTIONS FOR CUTTING CROWN MOLD- ING LAYING FLAT AND USING THE COMPOUND FEATURE ...

  • DeWalt DW708 - page 19

    Special Cuts NEVER MAKE ANY CUT UNLESS THE MATERIAL IS SECURED ON THE TABLE AND AGAINST THE FENCE. Aluminum Cutting: Certain workpieces, due to their size, shape or surface finish, may require the use of a clamp or fixture to prevent movement during the cut. Position the material so that you will be cutting the thinnest cross section, as shown in F ...

  • DeWalt DW708 - page 20

    16 English To adjust the tension, loosen, but do not remove, the six screws (Figure 39). Then rotate the set screw on the top of the motor plate casting until the proper tension is achieved. Tighten the six screws securely and replace the belt cover. NOTE: Overtightening the belt will cause premature motor failure. Maintenance 1. All bearings are s ...

  • DeWalt DW708 - page 21

    17 English T rouble Shooting Guide BE SURE TO FOLLOW SAFETY RULES AND INSTRUCTIONS TROUBLE! SAW WILL NOT START WHAT’S WRONG? WHAT TO DO… 1. Saw not plugged in 1. Plug in saw. 2. Fuse blown or circuit breaker tripped 2. Replace fuse or reset circuit breaker 3. Cord damaged 3. Have cord replaced by authorized service center 4. Brushes worn out 4. ...

メーカー DeWalt カテゴリー Saw

DeWalt DW708のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- DW708の取扱説明書
- DeWaltの製品カード
- パンフレット
- またはDeWalt DW708の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、DeWalt DW708の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、DeWalt DW708の取り付け説明書、サービスマニュアル、簡易説明書、またはDeWalt DW708のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、DeWalt DW708の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

DeWalt DW708デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがDeWalt DW708を使用するのを助ける技術的文書のことです。説明書は通常、全てのDeWalt DW708ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

DeWaltの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. DeWalt DW708の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははDeWalt DW708の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。DeWalt DW708に関してこのドキュメントで見つけることができる全てのヒントの目次
3. DeWalt DW708デバイスの基本機能を使うにあたってのヒント。 DeWalt DW708のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。DeWalt DW708に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるDeWalt DW708のメーカー/サービスへの連絡先に関する情報。

DeWalt DW708についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもDeWalt DW708の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがDeWalt DW708で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)