Cannon 10TSの取扱説明書

28ページ 3.08 mb
ダウンロード

ページに移動 of 28

Summary
  • Cannon 10TS - page 1

    OWNER’S MANU AL NOTE: Do not return your CANNON® Do wnrigger to your retailer. Your retailer is not authorized to repair or replace t his unit. You may obtain service b y: • calling CANNON® at 1-800-2 27-6433; • returning your do wnrigger to the Factor y Service Center; • sending or taking your d ownrigger to any CA NNON® Authorized Serv ...

  • Cannon 10TS - page 2

    2 Parts Description 1. Reel This is used to spool the cable, available in length s ranging from 1 50 to 400 feet. 2. Boom This is used to extend the weight out from the body of the downrigger and has a pulley fixed to its end. Boom lengths range from 24 to 53 inches. 3. Swivel Head This relays the cable at the end of the boom to lower the wei ght. ...

  • Cannon 10TS - page 3

    3 Downrigger Mounting on Boats A downrigger should be mounted where ever it is easy to operate and observe. You want to be able to see your fishing rod and to react quickly. So, choosing a good spot to mount your downrigger on your boat is 99% of the job. Due to the great variety of boats available, mounting your downrigger can be a dilemma. Having ...

  • Cannon 10TS - page 4

    4 Side Rail Mounting Side/Rail mounts can be mounted to a welded T-section. It can also be used at the two rail section butt joint. In both installations it is recommended to use a non-slip material, such as rubber or a thin wood sheet, between metal surfaces. You can also use these for mounting to a very narrow side gunwale. There is a plate provi ...

  • Cannon 10TS - page 5

    5 MOUNTING & SETUP Outboard Fa cing Stern Facing Rear or Stern Note Locking Slots in Base Side or Gunwale Decks up to 7/16" Thick Base Wellnuts Decks Thicker Than 7/16" Washer, Lock Washer, and 1/4-20 Hex Nut Base Inst alling the Base on Y our Boat Decks up to 7/16" thick Where access to the underside of the deck is not available ...

  • Cannon 10TS - page 6

    6 Decks thinner than 1/4" Use a Cannon Deck Plate to prevent deflection and add stability to decks thinner than 1/4". Use the deck plate as a template to mark the hole locations. If access to the underside of the deck is not available, the deck plate can be mounted using screws and wellnuts. Drill 1/2" holes. Use four 1/4”-20 x 2&q ...

  • Cannon 10TS - page 7

    7 Clamps Standard 24" Boom #8 x 5/8" Screw (1) #4 x 1/2" Screws (2) The 3/4"-Long Phillips Screw Must Engage Hole in Boom Setting Up Y our Downrigger Attaching the Boom Telescopic Boom The intermediate section of the telescopic boom must be extended approximately 5" before the boom locking screw can engage the hole in the b ...

  • Cannon 10TS - page 8

    8 Attaching the crank handle Thrust Bearing Spring Races Crank Handle Att aching the Crank Handle Assembly Make sure the thrust bearing is sandwiched between its two races. The thrust bearing spring should be oriented where the narrow end is toward the bearing. Slide the bearing with races and spring over the ratchet shaft. Then, carefully thread t ...

  • Cannon 10TS - page 9

    9 T erminating the Downrigger Cable Cannon Uni-Release The Cannon Uni-Release attaches directly to the downrigger weight. Attach fishing line to the clip at the end of the release, and then click through a series of increasing tension settings. The release can be used with any test line on salt or fresh water and may be adjusted from 2 to 22 pounds ...

  • Cannon 10TS - page 10

    10 CAUTION: This rod holder is intended for use of up to 30 lb. test line only, and is not recommended for use with any tackle IGFA rated higher than 30 lb. A safety strap (not included) is recommended for all applications. The rod holder assembly is not warranted when used with tackle above 30 lbs. Equipment placed in the rod holders and the loss ...

  • Cannon 10TS - page 11

    11 Operating Y our Downrigger After mounting the Cannon downrigger to your boat, release some line from your rod and reel so that the lure is anywhere from 5 to 100 feet behind the boat. This is called drop back. Attach the fishing line firmly into the line release. Lower the weight to the desired depth as indicated on the depth meter. Place the fi ...

  • Cannon 10TS - page 12

    12 Blowback Blowback Simply stated, blowback is what happens to the downrigger weight when you pull it through the water behind your boat. As your speed increases, so does the horizontal distance between the weight and your downrigger. The faster you go, the farther the weight is behind you. The farther the weight is behind you, the shallower the w ...

  • Cannon 10TS - page 13

    13 Adjusting the Depth Meter The Cannon Depth Meter provides non-slip accuracy, plus easy resetting. To reset, just slide the meter away from the reel until the gears are disengaged. Spin meter gear to change setting. NOTE: Actual fishing depth may vary from depth shown on meter due to trolling speed and weight of cannon ball. (See "Blowback&q ...

  • Cannon 10TS - page 14

    14 TROLLING TIPS T en Good T r olling Tip s 1) Test your lures over the boat side before sending them down and back. Do this to make sure the lure wiggles and wobbles properly without going belly up or wandering off. Some lures can be adjusted, fine tuned actually, to impart maximum action. For example, a slight bend in the tail of a spoon or twist ...

  • Cannon 10TS - page 15

    15 CANNON® LIMITED W ARRANTY Johnson Outdoors Inc. warrants to the original purchaser that if the accompanying product (see ex clusions below) proves to be defective in material or workmans hip within the following warranty periods, Johnson Outdoors Inc. will, at its option, either repair or replace same without charge (but no cash refunds will be ...

  • Cannon 10TS - page 16

    16 For a current list of aut horized Cannon Service Center s, including those ou tside of the US and Canada, please see our web page at www.cannondow nriggers.com . All CANNON Downriggers are covered by US Pat.D-269, 9 92. Copyri ght 2006 Johnson Outdoors, In c. All rights reserved. Conforms t o 89/336/ EEC (EMC) under standards EN 55022A, EN 50082 ...

  • Cannon 10TS - page 17

    TM UNI-TROLL 10 1901100 Form No. 3394905 Rev 12/06 ...

  • Cannon 10TS - page 18

    1 3330002 FRAME - UNI-TROLL 29 3321001 COVER - CLUTCH, ROUND (LEXAN) 57 2371712 WASHER - 9/32" FLAT [4.EA] 2 3327004 DECAL - NOSE, UNI-TROLL 30 9250003 PIN - DOWEL 3/16" x 7/8" - RATCHET 58 9100100 TERMINATOR 3 9040040 HOOK - 1/4" - 20 ROLLED 31 9400070 SPRING - DOG RATCHET 59 9100101 TERMINATOR CUSHION 4 2263102 NUT - HEX 1/4&q ...

  • Cannon 10TS - page 19

    TM UNI-TROLL 10 METRIC 1901101 Form No. 3394913 Rev 12/06 ...

  • Cannon 10TS - page 20

    1 3330002 FRAME - UNI-TROLL 29 0902000 CRANK HANDLE - UNI-TROLL 57 2263102 NUT - HEX 1/4"-20 [4.EA] 2 3327004 DECAL - NOSE, UNI-TROLL 30 3321001 COVER - CLUTCH, ROUND (LEXAN) 58 2371712 WASHER - 9/32" FLAT [4.EA] 3 9040040 HOOK - 1/4" - 20 ROLLED 31 9250003 PIN - DOWEL 3/16" x 7/8" - RATCHET 59 9100100 TERMINATOR 4 2263102 ...

  • Cannon 10TS - page 21

    TM UNI-TROLL 10 TS 1901110 Form No. 3394914 Rev 12/06 ...

  • Cannon 10TS - page 22

    1 3392506 FRAME - UNI-TROLL, WHITE 29 3390202 COVER - CLUTCH, ROUND, WHITE (LEXAN) 57 2371712 WASHER - 9/32" FLAT [4.EA] 2 3327004 DECAL - NOSE, UNI-TROLL 30 9250003 PIN - DOWEL 3/16" x 7/8" - RATCHET 58 9100100 TERMINATOR 3 9040040 HOOK - 1/4" - 20 ROLLED 31 9400070 SPRING - DOG RATCHET 59 9100101 TERMINATOR CUSHION 4 2263102 N ...

  • Cannon 10TS - page 23

    TM UNI-TROLL 10 TS/E 1901111 Form No. 3394919 Rev 12/06 ...

  • Cannon 10TS - page 24

    1 3392506 FRAME - UNI-TROLL, WHITE 29 0902000 CRANK HANDLE - UNI-TROLL 57 2263102 NUT - HEX 1/4"-20 [4.EA] 2 3327004 DECAL - NOSE, UNI-TROLL 30 3390202 COVER - CLUTCH, ROUND, WHITE (LEXAN) 58 2371712 WASHER - 9/32" FLAT [4.EA] 3 9040040 HOOK - 1/4" - 20 ROLLED 31 9250003 PIN - DOWEL 3/16" x 7/8" - RATCHET 59 9100100 TERMINA ...

  • Cannon 10TS - page 25

    TM UNI-TROLL 5 1901105 Form No. 3394915 Rev 12/06 ...

  • Cannon 10TS - page 26

    1 3330002 FRAME - UNI-TROLL 23 0467694 BRAKE PLATE - RATCHET 45 2277002 >UNIVERSAL LINE RELEASE 2 3327004 DECAL - NOSE, UNI-TROLL 24 1000904 SHAFT - RATCHET - UNI-TROLL 46 3992300 SWIVEL HEAD ASSEMBLY 3 9040040 HOOK - 1/4" - 20 ROLLED 25 9010310 WASHER - THRUST [2.EA] 47 0267001 ► SIDE PLATE (RH) 4 2263102 NUT - HEX 1/4"-20 26 901028 ...

  • Cannon 10TS - page 27

    TM UNI-TROLL 5 METRIC 1901106 Form No. 3394916 Rev 12/16 ...

  • Cannon 10TS - page 28

    1 3330002 FRAME - UNI-TROLL 23 1264670 CLUTCH PAD 45 9430160 >WASHER - STAR 5/16" 2 3327004 DECAL - NOSE, UNI-TROLL 24 0467694 BRAKE PLATE - RATCHET 46 2277002 >UNIVERSAL LINE RELEASE 3 9040040 HOOK - 1/4" - 20 ROLLED 25 1000904 SHAFT - RATCHET - UNI-TROLL 47 3992300 SWIVEL HEAD ASSEMBLY 4 2263102 NUT - HEX 1/4"-20 26 9010310 W ...

メーカー Cannon カテゴリー Fishing Equipment

Cannon 10TSのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 10TSの取扱説明書
- Cannonの製品カード
- パンフレット
- またはCannon 10TSの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Cannon 10TSの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Cannon 10TSの取り付け説明書、サービスマニュアル、簡易説明書、またはCannon 10TSのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Cannon 10TSの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Cannon 10TSデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがCannon 10TSを使用するのを助ける技術的文書のことです。説明書は通常、全てのCannon 10TSユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Cannonの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Cannon 10TSの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははCannon 10TSの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Cannon 10TSに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Cannon 10TSデバイスの基本機能を使うにあたってのヒント。 Cannon 10TSのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Cannon 10TSに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるCannon 10TSのメーカー/サービスへの連絡先に関する情報。

Cannon 10TSについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもCannon 10TSの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがCannon 10TSで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)