Scotsman Ice SCCP50の取扱説明書

32ページ 0.93 mb
ダウンロード

ページに移動 of 32

Summary
  • Scotsman Ice SCCP50 - page 1

    Introduction: This ice machine is the result of Scotsman ’s decades of experience as an industry leader in the design and manufacture of both commercial and residential ice machines. This manual includes the information needed to install, start up and maintain the ice machine. Note any Caution or Warning indicators, as they provide notice of pote ...

  • Scotsman Ice SCCP50 - page 2

    Specifications This ice machine is designed to be used indoors, in a controlled environment. It can be used in a wide variety of environmental conditions, but there are limits. Use outside of the listed limitations is misuse and will void the warranty. Air temperature limits: The ice machine will operate adequately within the limits, but functions ...

  • Scotsman Ice SCCP50 - page 3

    Cabinet Layout June 2008 Page 3 SCCG50 & SCCP50 Service Manual 14 7/8" AIR IN AIR OUT .75 SHEET MET AL DOOR FRONT .63 MIN. CABINET DOOR 29 1/4" 1" LEG ADJUSTMENT (4) PLACES 33 3/8" MIN. 34 3/8" MAX. 22" 2 3/4" 4" 3 3/4" 1 1/2" 2 1/2" 3 1/4" 7 3/8" 115 V POWER CORD DRAIN FLEXIBLE T ...

  • Scotsman Ice SCCP50 - page 4

    Air flow The machine takes in room temperature air at the lower right front and forces warm air out the lower left front. Restricting the airflow will adversely affect the ability of the ice machine to make ice. Scotsman Ice Systems are designed and manufactured with the highest regard for safety and performance. They meet or exceed the standards o ...

  • Scotsman Ice SCCP50 - page 5

    Water Quality All water, including potable water supplied by municipalities, contains some impurities or minerals. Water absorbs impurities from the air as rain and/or as it flows through the ground. Some of the impurities are solid particles, these are known as suspended solids, and a fine particle filter will remove them. Other impurities are che ...

  • Scotsman Ice SCCP50 - page 6

    Door Covering Door Panel The ice machine is supplied without a conventional door covering so it can be decorated to the user ’s preference. Scotsman offers several coverings including white, black and stainless steel. In addition, a custom built panel can be placed onto the door. Door Panel Attachment To attach a Scotsman supplied panel: Note: If ...

  • Scotsman Ice SCCP50 - page 7

    Door Panel Attachment June 2008 Page 7 SCCG50 & SCCP50 Service Manual Gasket Scotsman Door Panel Cover Machine Screw Use Upper Hole at the Top Use Lower Hole at the Bottom Hole Plug ...

  • Scotsman Ice SCCP50 - page 8

    Custom Panel A custom panel of wood or other material not exceeding 15 lb can be attached to the door. Attachment is from the ice side of the door. Holes are provided in the door for this purpose. To create and attach a custom panel: • Panel width: 14 7/8” • Panel height: Between 29 3/8” and 30 3/8”. • Panel thickness: 5/8” to ¾” 1 ...

  • Scotsman Ice SCCP50 - page 9

    Door swing change The door can be attached to open with hinges on the left or right using new brackets shipped loose in the ice bin. Retain all screws for re-use. To change: 1. Remove innermost screw holding each hinge to cabinet, loosen the other. 2. Slide hinges to the side and remove door from cabinet. Remove screws loosened in step 1 from both ...

  • Scotsman Ice SCCP50 - page 10

    Installation: Water & Drain The recommended water supply tubing is ¼ inch OD copper. Stainless steel flex or reinforced PVC tube may also be used. Install an easily accessible shut-off valve between the supply and the unit. This shut-off valve should not be installed behind the unit. Note: Do not use self-piercing type valves. 1. Remove the fr ...

  • Scotsman Ice SCCP50 - page 11

    Gravity Drain Caution: Restrictions in the drain system to the machine will cause water to back up into the ice storage bin and melt the ice. Gravity drain tubing must be vented, have no kinks and slope to the building drain. Air gaps are typically required by local code. 1. Place the ice machine in front of the installation opening. Adjust levelin ...

  • Scotsman Ice SCCP50 - page 12

    Electrical The ice machine is supplied with a power cord. Do not remove the grounding pin from the cord ’s plug. Do not use extension cords. Follow all codes. Connect the machine to its own 115 volt, 15 amp circuit. 1. If the electrical outlet for the ice maker is behind the unit, plug in the unit. 2. Position the unit in the installation opening ...

  • Scotsman Ice SCCP50 - page 13

    Cube Size Adjustment The cube size can be adjusted by changing the amount of freeze cycle time. This is done by a button press sequence. Note: There is only one correct cube size. See the illustrations. To adjust cube size: 1. Shut the machine off: If it 's off on bin full press and release the On/Off button once, switching the Ice Making ligh ...

  • Scotsman Ice SCCP50 - page 14

    Harvest Time Adjustment The harvest time can be adjusted so that all the ice harvests during the cycle, plus a few seconds extra. This is done by a button press sequence. Note: Do not set harvest time shorter than the actual time it takes to release all the cubes. To adjust Harvest Time: 1. Shut the machine off by holding the On/Off button in until ...

  • Scotsman Ice SCCP50 - page 15

    Control Settings Automatic water purge enable / disable The control is set at the factory to automatically select the proper amount of water purge. If desired, that can be disabled, and a typical purge amount used. To disable Automatic purge selection: 1. Press and hold the On/Off button until the unit shuts off. No lights should be on. 2. Press an ...

  • Scotsman Ice SCCP50 - page 16

    Use No special instructions are needed for use. Just take as much ice as you need, the machine will replace it. A scoop is provided, and it can be stored in the machine using the loop of tubing on the right side as a holder. The machine can be shut off anytime by just pushing and releasing the On/Off button. The machine will shut off at the end of ...

  • Scotsman Ice SCCP50 - page 17

    How to clean the condenser and winterize. Condenser cleaning The condenser is like the radiator on a car, it has fins and tubes that can become clogged with dirt and lint. To clean: 1. Remove the kickplate and front service panel. 2. Locate the condenser surface. 3. Vacuum the surface, removing all dust and lint. Caution: Do not dent the fins. 4. R ...

  • Scotsman Ice SCCP50 - page 18

    How to remove scale from the ice making system. 1. Scoop out all of the ice, either discard it or save it in an ice chest or cooler. 2. Press and HOLD the On/off button in for 3 seconds until the Green light goes out. 3. Press and HOLD the both the Clean-Reset and On/Off buttons for 5 seconds. The Time to Clean light will blink on and off. 4. Pour ...

  • Scotsman Ice SCCP50 - page 19

    System Information Overall: • Refrigerant: 8 oz R-134a • Compressor: Hermetic, 1300 BTUH, X HP • Condenser: Forced draft • Fan blade: 5 blade, 7 inch • Evaporator: Inverted, 24 cube cells. Copper cups attached to continuous serpentine • Metering device: Cap tube • Defrost method: Hot gas bypass with water assist • Spray method: 6 wa ...

  • Scotsman Ice SCCP50 - page 20

    Water System The controller uses a Water Sensor to check for the presence of water in the reservoir and to measure the conductivity of the water. The water sensor consists of two stainless steel probes located in a holder next to the water pump. The probes sense the conductivity of the water. The higher the mineral content of the water, the better ...

  • Scotsman Ice SCCP50 - page 21

    Components June 2008 Page 21 SCCG50 & SCCP50 Service Manual Control Panel, Bin Light and Curtain Evaporator Platen Scoop and Thermostat Bracket Evaporator and Controller Condenser and Bin Thermostat Inlet Water Solenoid Valve Model and Serial Tag Location ...

  • Scotsman Ice SCCP50 - page 22

    Controller The controller is located at the front of the unit, under the top panel. It is powered by a 12 volt transformer. It has 5 indicator lights: • Compressor - Light is ON if compressor is powered • Water - Light is ON if inlet water solenoid valve is powered • Hot Gas - Light is ON when Hot Gas Valve is powered • Fan - Light is ON wh ...

  • Scotsman Ice SCCP50 - page 23

    Performance Information Ice per cycle: 1 lb Water drained / cycle: Varies by harvest cycle length and purge setting. Typical amounts are @ 70/50 = 52 oz. @ 90/70 = 13 oz Compressor amps: 2.6 - 3.2 June 2008 Page 23 SCCG50 & SCCP50 Service Manual Freeze Cycle, Minutes Air Temperature 100 90 80 70 60 50 Water Temperature 100 37-38 36-37 34-35 32- ...

  • Scotsman Ice SCCP50 - page 24

    Refrigeration System June 2008 Page 24 SCCG50 & SCCP50 Service Manual Suct i on Pressur e -1 0 0 10 20 30 40 50 60 70 Ti m e PSIG D isch ar g e P r e ssur e 50 60 70 80 90 10 0 110 12 0 13 0 14 0 15 0 Tim e PSIG ...

  • Scotsman Ice SCCP50 - page 25

    Thermistor Values June 2008 Page 25 SCCG50 & SCCP50 Service Manual 0 ···· 85325 1 ···· 82661 2 ···· 80090 3 ···· 77607 4 ···· 75210 5 ···· 72896 6 ···· 70660 7 ···· 68501 8 ···· 66415 9 ···· 64400 10 · · · 62453 11 · · · 60571 12 · · · 58752 13 · · · 56995 14 · · · 55296 15 · · · 53653 1 ...

  • Scotsman Ice SCCP50 - page 26

    Service Diagnosis No Ice Problem Likely Cause Probable Solution No power to unit Power disconnected Check breaker or fuse. Reset or replace, restart and check No power to controller Transformer open Replace transformer Shut down on maximum water fill time - water light flashing Water shut off Restore water supply Very long freeze cycle Water leak C ...

  • Scotsman Ice SCCP50 - page 27

    Service Diagnosis Makes excessive noise Problem Likely Cause Probable Solution Fan blade vibrates Blade is bent Replace fan blade Fan motor mount is broken Replace motor mount Compressor vibrates Mounting loose Check mounting Water pump vibrates Pump bearings worn Replace pump Panels vibrate Mounting screws loose Tighten screws Makes ice, does not ...

  • Scotsman Ice SCCP50 - page 28

    Removal and Repair Bin Thermostat 1. Disconnect electrical power. 2. Remove service panel. 3. Remove back panel. Note: If unit is built in it must be pulled out to change the bin thermostat. 4. Pull cap tube out from the back of the ice storage bin and cap tube holder. 5. Remove two screws and the bin thermostat contact section from its mounting br ...

  • Scotsman Ice SCCP50 - page 29

    Removal and Repair Evaporator Thermistor Note: If unit is built in it must be pulled out to change the evaporator thermistor . 1. Shut machine off. If unit was making ice, manually harvest the ice. 2. Disconnect electrical power. 3. Remove top panel. 4. Remove cover from controller box. 5. Disconnect thermistor wire from controller. 6. Locate therm ...

  • Scotsman Ice SCCP50 - page 30

    Removal and Repair - Cabinet Removal Certain components require the removal of the cabinet for repair access. 1. If the machine is in a freeze mode, perform a manual harvest. 2. Remove all ice. 3. Drain reservoir. 4. Remove service panel and kick plate. 5. Remove back panel. 6. Disconnect electrical power. 7. Disconnect water and drain tubing. 8. R ...

  • Scotsman Ice SCCP50 - page 31

    18. Remove two screws holding freezing compartment brace to cabinet, lift brace up. 19. Lift evaporator platen up and tilt back enough for bin assembly to clear the base. 20. Remove air baffle. 21. Unplug 7 wire harness connector (at back of bin). 22. Remove 1 screw at each corner of the base. 23. Lift bin assembly off the base. Note: Prop evaporat ...

  • Scotsman Ice SCCP50 - page 32

    Refrigeration Service This ice machine use R-134a type refrigerant. There are specific rules for handling that refrigerant. To check for system pressures, add a field supplied clamp-on type service valve as a temporary means of system access. After diagnosis and before final repair, replace the clamp-on type valve with valves that are brazed onto t ...

メーカー Scotsman Ice カテゴリー Ice Maker

Scotsman Ice SCCP50のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- SCCP50の取扱説明書
- Scotsman Iceの製品カード
- パンフレット
- またはScotsman Ice SCCP50の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Scotsman Ice SCCP50の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Scotsman Ice SCCP50の取り付け説明書、サービスマニュアル、簡易説明書、またはScotsman Ice SCCP50のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Scotsman Ice SCCP50の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Scotsman Ice SCCP50デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがScotsman Ice SCCP50を使用するのを助ける技術的文書のことです。説明書は通常、全てのScotsman Ice SCCP50ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Scotsman Iceの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Scotsman Ice SCCP50の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははScotsman Ice SCCP50の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Scotsman Ice SCCP50に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Scotsman Ice SCCP50デバイスの基本機能を使うにあたってのヒント。 Scotsman Ice SCCP50のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Scotsman Ice SCCP50に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるScotsman Ice SCCP50のメーカー/サービスへの連絡先に関する情報。

Scotsman Ice SCCP50についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもScotsman Ice SCCP50の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがScotsman Ice SCCP50で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)