ページに移動 of 52
OPERATOR'S MANUAL Model C712 Soft Serve Freezer Original Operating Instructions 062179-M 2/03/ 05 (Ori ginal P ubli cati on) Updated 8/ 27/14 ...
Com plete this pa ge for quick r efer ence w hen ser vice is r equir ed: Taylor Distributor: Address: Phone: Fax: E-mai l: Serv ice: Par ts: Date of Installation: Infor mati on found on the data la bel: Model Number: Seri al Number: Electrical S pecs: Voltage Cycle Phase Maximum Fuse Si ze: A Minimum Wi re Ampaci ty: A E 2005 Carrier Commer cial Re ...
Table of Cont ents Model C7 12 T able of Contents Section 1 To the Installer 1 ............................................ Installer Safety 1 ........................................................ Site P reparation 1 ....................................................... Air Cool ed Units 1 ...................................................... ...
Table of Cont ents Mode l C71 2 Table of Contents - P age 2 Disassemb ly 32 .......................................................... Brush Cleani ng 33 ....................................................... Se ction 7 Impor tant: Opera tor Checkl ist 34 .............................. During Cl eaning and Saniti zing 34 .......................... ...
1 Model C7 12 To the Insta ller 131 121 Section 1 To the Installer The f ollowing infor mation has been included in t he manual as saf ety and regulat ory guidelines. F or complet e inst allation inst ruc tions, please s ee the Inst allat ion Checklist . Installer Safety In all areas of the world, equipment should be installed i n accordanc e with ...
2 Model C7 12 To the Insta ller 130304 Water C onnections (W ater Coo l ed Un its O n ly) An adequate c old water supply m ust be pr ovided with a hand shut -of f v alve. On t he underside of t he base pan or on t he right side, two 3/ 8” I .P .S. wat er connect ions f or inlet and outlet are prov ided for easy hook-up. 1/ 2” inside diamet er w ...
3 Model C7 12 To the Insta ller 130923 Beater Rotation Beater rot ation m ust be c lockwis e as viewed looking int o the f reezing cy linder. Note: T he f ollowing procedures should be perf ormed by a tr ained serv ice t echnician. To c orrect t he rotat ion on a t hree-phase unit , inter change any t wo incoming power supply lines at fr eezer main ...
4 Model C7 12 To the Opera tor 131 121 Section 2 To the Operator Your f reezer has been car efully engineer ed and manuf actur ed to give y ou dependable operat ion. This unit , when properly operat ed and cared f or, will produce a c onsist ent qualit y produc t. Like all mechanic al product s, i t will requir e cleaning and maint enance. A minimu ...
5 Model C 71 2 Safety 130304 Se cti on 3 Sa fety We at Tay lor are c oncerned about the s afet y of the operat or when he or she c omes in c ontact wit h the fr eezer and it s part s. Tay lor has gone t o ext reme eff ort s to des ign and manuf actur e built- in safet y feat ures t o prot ect both y ou and the ser vice technic ian. A s an exam ple, ...
6 Model C 71 2 Safety 130304 DO NOT use a w ater jet t o clean or rins e the f reezer . F ailure t o follow t hese inst ruct ions m ay result in serious elect rical s hock. S DO NOT allow unt rained pers onnel to operat e this m achine. S DO NOT operat e t he freez er unless all serv ice panels and access doors ar e restrain ed with screw s. S DO N ...
7 Mo del C712 Op erato r Parts I den ti fi catio n 130703 Section 4 Operator Parts Identif ication Model C712 Figur e 1 ...
8 Model C 71 2 O perat or P arts Id ent if icati o n 130703 C712 Exploded View P arts Identification ITE M DESCRIPTI ON PART NO. 1 COVER-HOPPER * BLACK* 053809-1 2 PUMP A.- MIX SI MPLIFIED SEE PG. 10 3 PANEL-REAR 064258- SER 4 PAN-DRI P 7.875 059737 5 PANEL-SI DE*RI GHT 059907 6 PAN-DRI P 12.5 059736 7 PANEL A.- FRONT-MI DDLE X63879 8 PANEL A.- FRO ...
9 Mo del C712 Op erato r Parts I den ti fi catio n 130703 Model C712 Door and Beater Assembly Figur e 2 ITE M DESCRIPTI ON PART NO. 1 HANDLE A.- DRAW-WELDED X56421-1 2 PLUG-PRI ME TWIN 059936 3 NUT-STUD- BLACK 3.250 LONG 058765 4 NUT-STUD- BLACK 2.563 LONG 058764 5 DOOR A.- 3SPT*LG BAFFLE X59921-SER 6 PIN- HANDLE-TWI N 059894 7 GASKET-DOOR HT 4&quo ...
10 Mode l C71 2 O perat or P arts Id en tif icat io n 140312 X57029-X X P ump A. - Mix S implified Figur e 3 ITE M DESCRIPTI ON PART NO. 1-7 PUMP ASSEMBLY - MIX SIMPLI FIED SOFT SERVE X57029- 14* 1 CYLINDER- PUMP-HOPPER- SOFT SERVE 057943 2 PIN- RETAININ G X55450 3 PISTON 053526 4 O-RI NG 2-1/8” OD - RED 020051 5 CAP-VALVE 056874- 14* 6 GASKET - ...
11 Mo del C712 Op erato r Parts I den ti fi catio n 140804 Accessor ies Figur e 4 ITE M DESCRIPTI ON PART NO. 1 PAIL- 10 QT. 013163 2 TOOL-O- RING REMOVAL 048260-W HT 3 TOOL-MI X PUMP SHAFT REMOVAL 057167 ITE M DESCRIPTI ON PART NO. 4 LUBRICANT- TAYLOR 4 OZ. 047518 *5 SANITI ZER-STERA SHEEN SEE NOTE ** KIT A. -TUNE- UP C712 X49463-81 * Not e: A sam ...
12 Model C 71 2 O perat or P arts Id ent if icati o n 121022 Br ushes Figur e 5 ITE M DESCRIPTI ON PART NO. 1 BLACK BRISTLE BRUSH 013071 2 DOUBLE END BRUSH 013072 3 WHITE BRI STLE BRUSH (1” x 2 ”) 013073 4 BRUSH SET (3) 050103 ITE M DESCRIPTI ON PART NO. 5 WHITE BRI STLE BRUSH (3” x 7 ”) 023316 6 BRUSH-END- DOOR-SPOUT 039719 7 BRUSH-PUMP SP ...
13 Model C7 12 Impor tant : To the Opera tor 130220 Section 5 Important: To the Operator Figur e 6 ITE M DESCRIPTI ON 1 POWER SWITC H 2 FLUORESCENT DISPLAY 3 KEYPADS 4 MIX OUT I NDICATOR 5 STANDBY KEY 6 MIX LOW INDI CATOR ITE M DESCRIPTI ON 7 SELECT KEY 8 SERVICE MENU KEY 9 BRUSH CLEAN COUNTER 10 ARROW KEYS 11 SYRUP TOPPING HEATER KEY ...
14 Model C7 12 Impor tant : To the Opera tor 1 10204 Sym bol De finitions To bet ter comm unicate in t he I nternat ional arena, sym bols have replac ed words on m any of our operat or switches , func tion, and fault indicat ors . Your T aylor equipm ent is designed with t hese Int ernat ional symbols . The f ollowing chart ident ifies t he sy mbol ...
15 Model C7 12 Impor tant : To the Opera tor 081205 Reset Mechanism The r eset but tons are locat ed in t he back panel of the mac hine. It prot ect s the beater m otor f rom an overload c ondition. Should an over load occur, t he reset m echanism will trip. T o properly reset t he freez er place t he power s witch in t he OF F position. Pres s the ...
16 Model C7 12 Impor tant : To the Opera tor 050722 Once the system has initia lized , t he SAFETY TI MEO UT s creen will dis play and the alar m will be on. ( See Figur e 9.) SAFETY TIMEOUT ANY KEY ABORTS Figur e 9 The SA FE TY T I MEO UT sc reen will be display ed with t he alarm on, f or 60 seconds or unt il any cont rol symbol i s selected. Aft ...
17 Model C7 12 Impor tant : To the Opera tor 050722 Enteri ng Access Code Wit h the A CCESS CO DE s creen on t he display use the SE L sym bol to set t he fir st c ode number in t he curs or posit ion. W hen the c orrec t number is select ed, t ouch t he SEL s ymbol t o move t he cur sor to t he next number pos ition. (See F igure 13. ) ENTER ACCES ...
18 Model C7 12 Impor tant : To the Opera tor Reset t he SE RVING CO UNTER by select ing the SEL s ymbol t o advance t o the nex t s creen. Select the UP arrow symb ol to move the arrow (>) to YES and select the S EL sy mbol. T he ser vings count er will reset to z ero and exit back to t he Manager' s Menu. (See F igure 16. ) RESET DRAW COUN ...
19 Model C7 12 Impor tant : To the Opera tor Enable the A UTO ST ART TI ME by select ing t he UP arrow s ymbol t o move t he arrow up t o Enable. Touc h the SE L sym bol to advanc e to t he next scr een. (S ee Figur e 22.) AUTO START TIME 00:00 Change >E x i t Figur e 22 Progr am the A UTO ST ART TI ME by select ing the UP arr ow symbol t o mov ...
20 Model C7 12 Impor tant : To the Opera tor 070322 Listed below are the v ariable mes sages which will appear, along with an explanat ion f or the c orrec tive act ion. NO F AULT FO UND - T here was no f ault found in the f reezer . Not hing will appear on t he scr een aft er this v ariable mes sage appears . BEATE R OV ERLO AD - Plac e the power ...
21 Model C 71 2 Op erati ng Pro ced ures Section 6 Operating Procedures The C712 m achine st ores m ix in a hopper. It has two 3. 4 quart (3. 2 liter) capacit y f reezing c ylinders with a t hree spout door. We begin our instr uct ions at t he point where we enter the st ore in t he morning and f ind t he parts disassem bled and laid out t o air dr ...
22 Model C 71 2 O perat in g Pro cedu res Step 6 Befor e inst alling the beat er ass embly, check the scr aper blades for any nick s or signs of wear . If any nicks are present , or if the blades ar e worn, replace both blades. If the blades are in good condit ion, install t he scr aper blade clips over the sc raper blades. P lace the r ear scr ape ...
23 Model C 71 2 Op erati ng Pro ced ures Step 10 To as semble t he freez er door, place t he door gasket s int o the gr ooves on t he back of the f reez er door. Figur e 37 Slide the f ront bearings over t he baff le rods . T he flanged edges should be against the door . DO NO T lu bri cate t he g askets o r fron t b earin g s. Slide the t wo o-r i ...
24 Mode l C71 2 O perat in g Pro cedu res Step 13 Slide the t hree o- rings int o the gr ooves of each standar d draw valv e. Slide t he H-r ing and o-ring int o the gr ooves of the c enter dr aw valve. Lubricat e t he H-ring and o- rings. Figur e 41 Step 14 Lubricat e the ins ide of t he fr eezer door s pouts, t op and bott om. Figur e 42 Step 15 ...
25 Model C 71 2 Op erati ng Pro ced ures 081205 Step 17 Slide the piv ot pin t hrough t he draw handles as the handles are ins erted int o t he draw valves . Figur e 45 Note: T his f reezer feat ures three adjus table dr aw handles to pr ovide port ion cont rol, giving a bet ter consis tent quality to your product and cont rolling cost s. The dr aw ...
26 Model C 71 2 O perat in g Pro cedu res Step 20 Inst all t he front drip t ray and splash shield under the door spout s. (See F igure 49. ) Figur e 49 Mix Pum p Assem bly Step 1 Ins pect t he rubber pump part s. O- rings and gask et must be in 100% good condit ion for the pum p and entir e machine t o operat e properly. T he o-rings and gasket ca ...
27 Model C 71 2 Op erati ng Pro ced ures 121022 Step 6 Slide the pum p valve gas ket i nto t he holes on the cap. DO NO T lubr icate t he gask et. (See F igure 54. ) Figur e 54 Step 7 Inser t t he valve body cap int o the hole in t he mix inlet adapt er. (See F igure 55. ) Figur e 55 Step 8 Inser t t he mix inlet ass embly int o the pum p cylinder. ...
28 Model C 71 2 O perat in g Pro cedu res 080908 Step 11 Inst all one red o- ring on each end of the m ix f eed tube, and thor oughly lubric ate. (See F igure 59. ) Figur e 59 Step 12 Lay the pum p assem bly, pump clip, cot ter pin, and mix f eed tube in t he bott om of t he mix hopper f or saniti zing. Step 13 Slide the lar ge black o- ring and th ...
29 Model C 71 2 Op erati ng Pro ced ures 121022 Note: Y ou have just sanit ized t he mix hopper and part s; t heref ore, be sure y our hands ar e clean and saniti zed befor e going on in these i nstr ucti ons. Step 3 While t he solut ion is flowing int o t he freez ing cylinder , t ake part icular c are to br ush-c lean the mix level sens ing probe ...
30 Mode l C71 2 O perat in g Pro cedu res 140804 Step 11 Wit h an empt y pail beneath t he door s pouts, rais e the pr ime plug and touc h the PU MP sy mbol . Step 12 When a s teady s tream of s anitizing s olution is flowing f rom t he prim e plug opening in the bot tom of the f reezer door, open the dr aw valve. Moment arily open the cent er dr a ...
31 Mode l C71 2 Op erati ng Pro ced ures 140804 Rinsing Step 1 Pour two gallons (7. 6 liter s) of cool, clean wat er into the m ix hopper. Wit h the whit e hopper br ush, s crub the m ix hopper and t he mix level s ensing probe. Using the double ended br ush, brush c lean the mix inlet hole. (See F igure 65. ) Figur e 65 Note: Do not brus h clean t ...
32 Model C 71 2 O perat in g Pro cedu res Step 4 Touc h the W ASH s ymbol . T his will caus e the cleaning solut ion in the f reezing c ylinder t o come in contac t wit h all areas of t he fr eezing cylinder . W ait at least 5 minut es bef ore proc eeding with t hese instr uct ions. ( See F igure 67.) Figur e 67 Step 5 Place an em pty pail beneat h ...
33 Model C 71 2 Op erati ng Pro ced ures 080908 Step 7 Remove t he two s mall o-r ings and one large o-r ing fr om each pump dr ive shaf t. Step 8 Remove t he fr ont drip t ray and splash s hield. Step 9 Remove all dr ip pans. T ake t hem t o the s ink for cleaning. (See F igure 69. ) Figur e 69 Note: I f the drip pans are f illed with an ex cessiv ...
34 Model C7 12 Impor tant : Opera tor C hec klis t 080107 Section 7 Important: Operator Checklist Dur ing Cl eaning and Sani tizing ALWAYS FOLLOW LOCAL HEALTH CODES. Clean in g and san i tiz in g sched u les are govern ed by fe der al, s ta te, or loca l re gulat ory age ncie s, and must be f ol lo w ed acco rdi ng ly. I f th e un i t has a “S ta ...
35 Model C7 12 Impor tant : Opera tor C hec klis t 080226 Winter S tor age If the plac e of bus iness is t o be clos ed during the winter mont hs, it is import ant t o protect t he freezer by following c ert ain precaut ions, part icularly if t he building is subjec t t o fr eezing condit ions. Disconnec t t he freez er f rom t he main power s ourc ...
36 Model C7 12 Impor tant : Opera tor C hec klis t Section 8 Troubleshooting Guide PROBL EM PROBABLE CAUSE REMEDY PAGE REF. 1. No produc t is being dispensed. a. Low on mix . T he MI X OUT light is on. a. Add m ix to the m ix hopper. Return t o AUT O mode. 30 b. The power swit ch is in the OF F posit ion. b. Place the power swit ch t o ON and sele ...
37 Model C7 12 Impor tant : Opera tor C hec klis t PROBL EM PROBABLE CAUSE REMEDY PAGE REF. 3. T he product is t oo thic k. a. Freezing c ylinder not primed co rrectly. a. Drain the f reezing c ylinder and reprim e the mac hine. 30 b. Air/m ix pump inc orrec tly assem bled. b. Follow assem bly procedur es caref ully. 26 c. The viscosity con trol is ...
38 Model C7 12 Impor tant : Opera tor C hec klis t PROBL EM PROBABLE CAUSE REMEDY PAGE REF. 10. The driv e shaft is s tuck in the dri ve coupling. a. Mix and lubricant collec ted in drive c oupling. a. Brush clean t he rear shell bearing area r egularly. 33 b. Rounded corners of driv e shaft , driv e coupling, or both. b. Call an authorized s ervic ...
39 Mo del C712 Parts Rep lacemen t S ched ul e Section 9 Parts Replacement Schedule PART DESCRIPTI ON EVERY 3 MONTHS EVERY 6 MONTHS ANNUALLY Scr aper Blade X Drive S haft Seal X Fr eezer Door Gas ket X Fr ont Bearing X Fr ont Beat er Shoes X Draw Valve O -Ring X Mix F eed Tube O -Ring X Pump O -Ring X Prime P lug O- Ring X Pump Valve Ga sket X Mix ...
40 Model C7 12 Limite d Warr ant y on Equipm ent 131 121 Section 10 Limited Warranty on Equipment TAYL O R COMP ANY LI MI TE D WARRANT Y O N FREE ZERS Tayl or Company, a divis ion of Carr ier Comm ercial Ref rigerat ion, Inc. (“ Tay lor”) is pleased t o provide t his limit ed warrant y on new T aylor- branded fr eezer equipm ent available f rom ...
41 Model C7 12 Limite d War ra nty on Equipme nt 3. Replacement of wear it ems designat ed as Class “000” part s in the T aylor Oper ator ’s Manual. 4. Ext ernal hoses , elec tric al power supplies , and mac hine grounding. 5. Part s not supplied or designat ed by Taylor , or damages r esulting f rom their us e. 6. Retur n trips or wait ing t ...
42 Model C 71 2 L imi ted W arrant y on Parts 131 121 Section 11 Limited Warrant y on Parts TAYL O R COMP ANY LI MI TE D WARRANT Y O N TAYL OR G ENUI NE PART S Tayl or Company, a divis ion of Carr ier Comm ercial Ref rigerat ion, Inc. (“ Tay lor”) is pleased t o provide t his limit ed warrant y on new T aylor genuine r eplacement component s an ...
43 Model C7 12 Limite d War ra nty on Par ts LI MI TED W ARRANTY EXCE PTI ONS This limit ed warrant y does not cover: 1. Labor or other cos ts inc urred for diagnos ing, repair ing, remov ing, inst alling, shipping, ser vicing or handling of defec tive Part s, r eplacement Par ts , or new P art s. 2. Normal m aintenance, cleaning and lubr ication a ...
44 Model C 71 2 L imi ted W arrant y on Parts LI MI TAT IO N OF WARRANT Y THI S L IMI TE D WARRANT Y I S EXCL USI VE AND I S I N LI EU O F AL L O THER W ARRANT IES , CO NDIT IO NS AND/O R REMEDI ES UNDER T HE LAW , I NCLUDI NG ANY IM PL IED W ARRANTI ES O R CONDIT IO NS O F MERCHANT ABIL IT Y O R FI TNE SS F OR A PART I CULAR PURP OSE . T HE O RIG ...
C712 059898-27 12/9/13 JUMPER INSTALLED-ACTIVATES SYRUP HEATERS. RESERVED (DO NOT USE) JUMPER INSTALLED-ENABLES 59 F HOPPER TEMPERATURE CHECK. RESERVED (DO NOT USE) 1 2 3 4 T8 T1 T7 T4 T5 BLACK BLUE BLACK T1 CP T2 L1 CP L2 BEATER MOTOR CONTACTOR LEESON BEATER MOTOR WIRING STEPS: 1) DISCONNECT WIRE T7 FROM TERMINAL 3 2) SPLICE BLUE WIRE AS SHOWN 1 2 ...
C712 059898-33 12/9/13 EXTERNAL GROUND L2 L1 TERMINAL BLOCK BLK/WHT INTERFACE BOARD POWER TRANSFORMER BLK ORN RED BLU 16V L2 EMI FILTER LOAD LINE L1 L1 L2 240V WHT NOT CONNECTED WHT WHT GRN/YEL GRN/YEL BLK GRN/YEL BLK/WHT POWER SWITCH 3PDT BLK ON OFF RED BLU GRN/YEL BLK BLK GRN HOPPER BARREL --THERMISTOR PROBES-- BLK BLK YEL YEL RIBBON CABLE BLU RE ...
C712 059898-40 12/9/13 EXTERNAL GROUND N L1 TERMINAL BLOCK BLK/WHT INTERFACE BOARD POWER TRANSFORMER BLK ORN RED BLU 16V L2 EMI FILTER LOAD LINE L1 L1 L2 240V WHT NOT CONNECTED WHT WHT GRN/YEL GRN/YEL BLK GRN/YEL BLK/WHT POWER SWITCH 3PDT BLK ON OFF RED BLU GRN/YEL BLU BRN GRN HOPPER BARREL --THERMISTOR PROBES-- BLK BLK YEL YEL RIBBON CABLE BLU RED ...
C712 059898-58 12/9/13 EXTERNAL GROUND N L1 TERMINAL BLOCK BLK/WHT INTERFACE BOARD POWER TRANSFORMER BLK ORN RED BLU 16V L2 EMI FILTER LOAD LINE L1 L1 L2 240V WHT NOT CONNECTED WHT WHT GRN/YEL GRN/YEL BLK GRN/YEL BLK/WHT POWER SWITCH 3PDT BLK ON OFF RED BLU GRN/YEL BLU BRN GRN HOPPER BARREL --THERMISTOR PROBES-- BLK BLK YEL YEL RIBBON CABLE BLU RED ...
Taylor C712のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- C712の取扱説明書
- Taylorの製品カード
- パンフレット
- またはTaylor C712の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Taylor C712の取扱説明書に含まれています。
取扱説明書と呼ばれる文書のグループは、Taylor C712の取り付け説明書、サービスマニュアル、簡易説明書、またはTaylor C712のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Taylor C712の製品を使用するにあたって最も人気のある説明書を閲覧できます。
Taylor C712デバイスの取扱説明書はどのようなものですか？
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがTaylor C712を使用するのを助ける技術的文書のことです。説明書は通常、全てのTaylor C712ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。
Taylorの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。
1. Taylor C712の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははTaylor C712の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Taylor C712に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Taylor C712デバイスの基本機能を使うにあたってのヒント。 Taylor C712のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Taylor C712に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるTaylor C712のメーカー/サービスへの連絡先に関する情報。
Taylor C712についてご質問がありますか？
次のフォームを使用してください
見つけた説明書を読んでもTaylor C712の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがTaylor C712で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。