-
Makita DHP448RMJ - page 1
GB Cordless Hammer Driver Drill Instruction manual F Perceuse Percussion-Visse use Manuel d’instructions sans Fil D Akku-Schlagbohrschra uber Betriebsanleitung I Trapano avvitato re Istruzioni per l’uso a batterie con percussione NL Accuschroef- Gebruiksaanwijzing boorhamermachine E Rotomartillo Atornilla dor Manual de instrucciones Inalámbric ...
-
Makita DHP448RMJ - page 2
2 1 012695 2 012128 3 012699 4 012700 5 012701 6 012702 7 012736 8 012735 1 2 3 4 5 6 7 A B 8 9 10 11 1 2 10 ...
-
Makita DHP448RMJ - page 3
3 9 012714 10 012711 11 012697 12 012708 13 012712 14 012698 15 012737 16 002449 2 13 14 15 16 17 18 19 20 21 22 23 14 24 25 26 ...
-
Makita DHP448RMJ - page 4
4 17 006258 18 012705 19 012706 20 012707 21 006304 27 28 29 30 31 32 33 34 33 ...
-
Makita DHP448RMJ - page 5
5 ENGLISH (Origina l instructions) Explanati on of general view SPECIFICATIONS • Due to our continuing program of research and developme n t, the specification s herein are subject to change without notice. • Specifications and battery cartridge may differ from country to country. • Weight, with battery cartridge, according to EPTA-Procedure ...
-
Makita DHP448RMJ - page 6
6 10. Some mat erial contains chemicals which may be toxic. Take caution to prevent dust inhalation and skin contact. Follow materi al supplier safety data. SAVE THESE INSTRUCTIONS. WARNING: DO NOT let comfort or familiarity with product (gained from repeated use) replace strict adher ence to safety rules for the subject product. MISUSE or failure ...
-
Makita DHP448RMJ - page 7
7 To start the tool, simply pull t he switch trigger. Tool speed is increas ed by incr easing pres sure on t he switch trigger. Release the switch trigger to stop. Lighting up the fr ont lamp (Fig. 4) CAUTION: • Do not look in the light o r see the source of light directly. Pull the switch trigger to light up the lamp. The lamp keeps on lighting ...
-
Makita DHP448RMJ - page 8
8 Installing or remo ving driver bit or drill bit (Fig. 11) Turn the sleeve counterclockwise to open the chuck jaws. Place the bit in the chuck as far as it will go . Turn the sleeve clockwise to tighten the ch uck. To remove the bit, turn the sleeve counterclockwise. Installing bit holder (Fig. 12) Fit the bit holder into the prot rusion at the to ...
-
Makita DHP448RMJ - page 9
9 Use a screwdriver to remove two screws then remove the rear cover. (Fig. 18) Raise the arm part of the spring and th en place it in the recessed part of the hou sing with a slotted bit screwdriver of slender shaft or the like . (Fig. 19) Use pliers to remove the carbon brush caps of the carbon brushes. Take out the worn carbon bru shes, insert th ...
-
Makita DHP448RMJ - page 10
28 NEDERLANDS (Origine le instructies) Verklaring van het onderdelenove rzicht TECHNISCHE GEGEVENS • Als gevolg van ons doorlopende onderzoeks- en ontwik kel ingsprogramma, zijn de te chnische gegevens van dit gereedschap onderhevig aan ve randeringe n zonder voorafgaande kennisgeving. • Specificaties en accu’s kunnen van land tot lan d versc ...
-
Makita DHP448RMJ - page 11
29 4. Houd het elektrisch gereedschap vast aan het geïsoleerde oppervlak van de handgrepen wanneer u werkt op plaatsen waar het bevestigingsmateriaal met verborgen bedrading in aanraking kan komen. Wanneer bevestigingsmaterialen in aanr aking komen met onder spanning staande d raden, zullen de niet-geïsoleerde metalen delen van het gereedschap on ...
-
Makita DHP448RMJ - page 12
30 • Oefen geen grote kracht uit bij het aanbrengen van de accu. Als de accu niet gemakkelijk erin kan worden geschoven, wordt deze ni et goed aangebrach t. Accubeveiligingssys teem (lithiumionaccu met een ster-merktek en) (zie afb. 2) Lithiumionaccu’ s met een ster-merkteken zijn uit gerust met een beveiligingssysteem. Dit systeem schakelt aut ...
-
Makita DHP448RMJ - page 13
31 schaalverdeling is uitgelijnd met de aanwijspunt op de behuizing van het gereedschap. Verschuif eerst de wer kin gsfunctie-instel knop naar de stand met het symbool . Het draaikoppel is minimaal wanneer stand 1 is uitg elijnd met de aanwijspunt , en maximaal wanneer het symboo l is uitgelijnd met de aanwijspunt. In de standen 1 t/m 21 zal de kop ...
-
Makita DHP448RMJ - page 14
32 keren wordt herhaald, zal het boo rgat schoon worden en kunt u normaal verder boren. Blaasbalgje (los verkrijgbaar) (zie afb. 16) Gebruik na het bor en het blaasbalgje om het stof uit het boorgat te blazen. Gebruik al s schroe vendraaie r Verschuif eerst de wer kin gsfunctie-instel knop naar de stand met het symbool . Stel de instelri ng in op h ...
-
Makita DHP448RMJ - page 15
33 • Blaasbalgje • Veiligheidsbril • Originele Makita accu en lader • Zijhandgreep, compleet • Dieptegeleider •H a a k • Rubberen accessoire • Wollen accessoire • Schuimrubberen polijstaccesso ire • Accubeschermer OPMERKING: • Sommige items op de lijst kun nen zijn inbegrepen i n de doos van het ge reedschap als standa ard toe ...
-
Makita DHP448RMJ - page 16
ALA Makita Corporation Anjo, Aichi, Japan 885234-991 www.makita.com ...
Makita DHP448RMJについてご質問がありますか?
次のフォームを使用してください
見つけた説明書を読んでもMakita DHP448RMJの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがMakita DHP448RMJで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。