Shindaiwa X7502824900の取扱説明書

28ページ 1.94 mb
ダウンロード

ページに移動 of 28

Summary
  • Shindaiwa X7502824900 - page 1

    T254 TRIMMER SHIND AIWA OWNER’S/OPERA T OR’S MANU AL WARNING! Minimize the risk of injury to yourself and others! Read this manual and familiarize yourself with the contents. Always wear eye and hearing pro- tection when operating this unit. X7502824900 04/10 ...

  • Shindaiwa X7502824900 - page 2

    2 The Shindaiwa H4 series of hand-held power equipment is designed and built to deliver superior performance and reliability without compromise to quality , comfort, safety or durability . Shindaiwa engines represent the leading edge of high-perfor- mance engine technology , delivering exceptionally high power with remarkably low displacement and w ...

  • Shindaiwa X7502824900 - page 3

    3 W ARNING! Engine exhaust IS HOT , and contains Carbon Monoxide (CO), a poison gas. Breathing CO can cause uncon- sciousness, serious injury , or death. Exhaust can cause serious burns. AL WA YS position unit so that exhaust is directed away from your face and body . War ning and Operational Labels Read and fol low t his oper ator' s manu al. ...

  • Shindaiwa X7502824900 - page 4

    4 T he Proper ly Equipped Oper a tor Always wear a harness when operating the unit . It adds comfort and helps ensure safety by limiting movement fore and aft. When the harness is adjusted properly , the unit should balance with the cutting attachment parallel to the ground. Always operate with both hands rmly gripping the unit. Wear close-tt ...

  • Shindaiwa X7502824900 - page 5

    5 Be Aware of the Wor king En vir onment Avoid long-term operation in very hot or very cold weather . Make sure bystanders or observers outside the 15 meter (50 feet) “danger zone” wear eye protection. Be extremely careful of slippery terrain, especially during rainy weather . If contact is made with a hard object, stop the engine and inspect t ...

  • Shindaiwa X7502824900 - page 6

    6 Specications Engine Name T254 Engine T ype 4-cycle, vertical cylinder , air cooled Dry Weight (Without guard and strap) 5.0 kg/1 1.0 lb. Bore x Stroke 34 x 27 mm (1.3 x 1.1 in.) Displacement 24.5 cc (1.5 cu. in.) Fuel/Oil Ratio 50:1 with *ISO-L-EGD or JASO FD class engine oil Fuel T ank Capacity 590 ml (20 oz.) Carburetor T ype Diaphragm-type ...

  • Shindaiwa X7502824900 - page 7

    7 NOTE The plastic shield is for use with the Nylon Line Head only . Install Metal Shield when using plastic or metal blades. 1. Remove plastic threaded shaft sleeve and adapter plate (C) from PTO shaft (A). 2. Placetheshieldonthebottomofthebearinghousingange. 3. Place shield plate (B) on shield, align holes. Ins ...

  • Shindaiwa X7502824900 - page 8

    8 Throttle lever free play 4-6 mm (3/16”-1/4”) Throttle Free Play Adjust throttle lev er fr ee play The throttle lever free play should be approximately 4 - 6 mm (3/16” - 1/4”). Make sure that the throttle lever operates smoothly without binding. If it becomes necessary to adjust the lever free play , follow the procedures and illustrations ...

  • Shindaiwa X7502824900 - page 9

    9 Handling Fuel DANGER Fuel is VERY ammable. Use extreme care when mixing, storing or handling or serious personal injury may result. • Use an approved fuel container . • DO NOT smoke near fuel. • DO NOT allow ames or sparks near fuel. • Fuel tanks/cans may be under pressure. Always loosen fuel caps slowly allowing pressure to equaliz ...

  • Shindaiwa X7502824900 - page 10

    10 Filling the fuel tank WARNING! Minimize the Risk of Fire Place the unit on a at, level surface. 1. Clear any dirt or other debris from around the fuel ller cap. 2. Remove the fuel cap, and ll the tank with clean, fresh fuel. 3. Reinstall the fuel ller cap and tighten rmly . 4. Wipe away any spilled fuel before starting engine. 5. ...

  • Shindaiwa X7502824900 - page 11

    11 Slide ignition to ON ON Throttle Lock Button Make sure the attachment is clear of obstructions! ...and pull recoil starter handle upward Hold the unit rmly ... Close choke Set the choke lever to the CLOSED position Star ting the Engine IMPORT ANT! Engine ignition is controlled by a two position switch mounted on the throttle housing labeled, ...

  • Shindaiwa X7502824900 - page 12

    12 Slide ignition to OFF OFF NEVER operate the unit with the cutting attachment shield or other protec - tive devices removed! Use only authorized Shindaiwa parts and accessories with your Shindaiwa trimmer . Do not make modications to this unit without written approval from Shindaiwa, Inc. AL W A YS make sure the cutting attachment is properly ...

  • Shindaiwa X7502824900 - page 13

    13 Operation W ARNING Engine exhaust IS HOT , and contains Carbon Monoxide (CO), a poison gas. Breathing CO can cause uncon- sciousness, serious injury , or death. Exhaust can cause serious burns. AL WA YS position unit so that exhaust is directed away from your face and body . CA UTION! Do not push the rotating line into trees, ■ wire fences or ...

  • Shindaiwa X7502824900 - page 14

    14 Maintenance WARNING! Before performing any main- tenance, repair , or cleaning work on the unit, make sure the engine and cutting attachment are completely stopped. Disconnect the spark plug wire before performing service or maintenance. WARNING! Non-standard accessories, cut - ting attachment, or replacement parts may not operate properly with ...

  • Shindaiwa X7502824900 - page 15

    15 spark plug gap--all models Components of air lter Filter element Prelter Loosen fasteners Remove the cover of the air lter Maintenance (continued) 10-Hour maintenance (more fr equently in dusty conditions) Remove the air lter cover by loos - 1. ening the cover screw(s) and lifting. Remove and inspect the pre-lter . 2. If the pre-? ...

  • Shindaiwa X7502824900 - page 16

    16 Maintenance (continued) Remove and replace the fuel filter element. Use a hooked wire to extract the fuel ■ filter from inside the fuel tank. Inspect the fuel filter element. If it shows signs of contamination, replace with a genu - ine Shindaiwa replacement fuel filter element. Before reinstalling the new filter ele- ■ ment, inspect th ...

  • Shindaiwa X7502824900 - page 17

    17 135-Hour Maintenance IMPORT ANT! If a new gasket is not available and/ or the old gasket is not damaged, the old gasket may be reused. Never use cracked or damaged gaskets! T urn engine over several times, and 6. returnthe to TDC-compression. Recheck with proper feeler gauge to make sure clearance adjust- ment did not change as a result of tight ...

  • Shindaiwa X7502824900 - page 18

    18 Engine Cover Screws Engine Cover Mufer Mufer Gasket Mufer Bolts Spark Arrester Screen Spark Arrester Cover Cover Screws With a 3 mm hex wrench remove the 1. engine cover screws and the engine cover . If the engine becomes sluggish and low on power , check and clean the spark arrester screen. IMPORT ANT! If you note excessive carbon buil ...

  • Shindaiwa X7502824900 - page 19

    19 Adjusting Engine Idle The engine must return to idle speed whenever the throttle lever is released. Idle speed is adjustable, and must be set low enough to permit the engine clutch to disengage the cutting attachment. WARNING! The cutting attachment must NEVER rotate at engine idle! If the idle speed cannot be adjusted by the procedure described ...

  • Shindaiwa X7502824900 - page 20

    20 T r oubleshooting Guide V aporlock. V alve adjustment. Engine hot/heat soaked. Low fuel quality . V alve clearance too tight. V alve clearance too loose. Let cool completely and restar t. Refill with fresh, clean unleaded gasoline with a pump octane of 89 or higher mixed with an air cooled engine oil that meets or exceeds ISO-L-EGD and/or JASO ...

  • Shindaiwa X7502824900 - page 21

    21 Is the engine overheating? Engine is rough at all speeds. May also have black smoke and/or unbur ned fuel at the exhaust. Operator is over working the unit. Carburetor mixture is too lean. Improper fuel ratio. Fan, fan cover , cylinder fins dir ty or damaged. Carbon deposits on the piston or in the muf fler . Clogged air cleaner element. Loose ...

  • Shindaiwa X7502824900 - page 22

    22 ADDITIONAL PROBLEMS Poor acceleration. Clogged air filter . Clogged fuel filter . Lean fuel/air mixture. Idle speed set too low . Ignition switch tur ned of f. Fuel tank empty . W ater in the fuel. Clogged fuel filter . Shor ted spark plug or loose ter minal. Ignition failure. Piston seizure. Ground (stop) wire is disconnected, or switch is d ...

  • Shindaiwa X7502824900 - page 23

    23 SHINDAIW A LIMITED W ARRANTY ST A TEMENT FOR PRODUCT SOLD IN USA AND CANADA BEGINNING 01/01/2010 ECHO, INC'S RESPONSIBILITY ECHO Incorporated’s (ECHO, INC.) Limited W arranty , provides to the original purchaser that this Shindaiwa product is free from defects in material and workmanship. Under normal use and maintenance from date of purc ...

  • Shindaiwa X7502824900 - page 24

    24 PURCHASED REP AIR P ARTS AND ACCESSORIES • 90-day all applications A TTENTION ENGINE POWERED PRODUCT OWNERS This Shindaiwa engine powered product is a quality-engineered unit which has been manufactured to exact tolerances to provide superior performance. T o help ensure the performance of the unit, it is required to use engine oil which meets ...

  • Shindaiwa X7502824900 - page 25

    25 ECHO INCORPORA TED EMISSION CONTROL W ARRANTY ST A TEMENT FOR ECHO AND SHINDAIW A BRANDS The Environmental Protection Agency (EP A) and the California Air Resources Board (C.A.R.B.) and ECHO Incorporated (ECHO Inc.) are pleased to explain the emission control system warranty on your 2010 and later equipment/small of f-road engine (SORE). New equ ...

  • Shindaiwa X7502824900 - page 26

    26 NO TES ...

  • Shindaiwa X7502824900 - page 27

    27 NO TES ...

  • Shindaiwa X7502824900 - page 28

    ECHO Incorporated. 400 Oakwood Road Lake Zurich, IL 60047-1564 U.S.A. T elephone: 1-877-986-7783 Fax: 1-847-540-8416 www .shindaiwa.com Y amabiko Corporation 7-2 Suehirocho 1-Chome, Ohme, T okyo, 198-8760, Japan Phone: 81-428-32-61 18 Fax: 81-428-32-6145 Ser vicing Infor mation Par ts/Serial Number Genuine Shindaiwa Parts and Assemblies for your Sh ...

メーカー Shindaiwa カテゴリー Trimmer

Shindaiwa X7502824900のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- X7502824900の取扱説明書
- Shindaiwaの製品カード
- パンフレット
- またはShindaiwa X7502824900の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Shindaiwa X7502824900の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Shindaiwa X7502824900の取り付け説明書、サービスマニュアル、簡易説明書、またはShindaiwa X7502824900のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Shindaiwa X7502824900の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Shindaiwa X7502824900デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがShindaiwa X7502824900を使用するのを助ける技術的文書のことです。説明書は通常、全てのShindaiwa X7502824900ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Shindaiwaの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Shindaiwa X7502824900の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははShindaiwa X7502824900の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Shindaiwa X7502824900に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Shindaiwa X7502824900デバイスの基本機能を使うにあたってのヒント。 Shindaiwa X7502824900のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Shindaiwa X7502824900に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるShindaiwa X7502824900のメーカー/サービスへの連絡先に関する情報。

Shindaiwa X7502824900についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもShindaiwa X7502824900の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがShindaiwa X7502824900で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)