Metra Electronics 99-7013の取扱説明書

12ページ 0.43 mb
ダウンロード

ページに移動 of 12

Summary
  • Metra Electronics 99-7013 - page 1

    INST ALLA TION INSTRUCTIONS FOR PART 99-7013 99-7013 APPLICA TIONS Mitsubishi Outlander 2007-2010 KIT FEA TURES • DIN Radio Provision with Pocket • ISO Mount Radio Provision with Pocket • Double DIN Radio Provision • Stacked ISO Mount Units Provision A) Radio Housing • B) ISO Br ac k ets • C) ISO T rim Plate • D) Double DIN Brackets ? ...

  • Metra Electronics 99-7013 - page 2

    Dash Disassembly - Mitsubishi Outlander 2007-2010. . . . . . . . . . . . . . . . . . . . 1 , 2 Kit Preparation ...........................................3 Kit Assembly - DIN Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - ISO Mount Radio Provision with Pocket ...................... . 5 - Double DIN/Stacked ...

  • Metra Electronics 99-7013 - page 3

    99-7013 DASH DISASSEMBL Y MITSUBISHI OUTLANDER 2007-2010 PAS SE N G ER AIR BAG O FF P A S S E N G E R PA S SEN GER AIR BAG O F F P AS SEN G ER B C 1 D isconnect the negative battery ter- minal to prevent an accidental short circuit. 1 Unclip and remove the vents from the left and right side of the factory radio panel. ( Figure A) Remove (4) Phillip ...

  • Metra Electronics 99-7013 - page 4

    99-7013 DASH DISASSEMBL Y MITSUBISHI OUTLANDER 2007-2010 2 Remo ve the labels from the front of the radio trim panel at each side of the hazar d switch by pushing them out from behind the panel. (Retain the labels to be reused during kit prepa- ration) ( Figure F) 6 E F Continued to kit preparation. REMOVE “9” PHILLIPS SCREWS (RE TA I N SCREWS) ...

  • Metra Electronics 99-7013 - page 5

    99-7013 KIT PREPARA TION 3 Secure the hazard switch panel into the radio housing using the factory hardwar e removed previously and apply labels from the front of the factory radio trim panel to front of the Metr a radio panel. (Figure A,B) 5 Continue to kit assembly . A PAS SEN GER AIR BAG OFF PAS SEN GER B MITSUBISHI OUTLANDER 2007-2010 ...

  • Metra Electronics 99-7013 - page 6

    4 99-7013 KIT ASSEMBL Y A B C DIN RADIO PROVISION WITH POCKET Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs outward. (Figure A) 1 Slide the aftermarket radio into the cage until it snaps into place . (Figure B) 2 Snap the pocket into the radio housing . (Figure C) 3 Continue to final assembly . * Note: Ref e ...

  • Metra Electronics 99-7013 - page 7

    99-7013 KIT ASSEMBL Y 5 B C D ISO MOUNT RADIO PROVISION WITH POCKET Mount the ISO Brackets to the after- market radio using the screws sup- plied with the radio. (Figure A) 1 Slide the radio into the Radio Housing until it snaps into place . (Figure B) 2 Snap the T rim Plate onto the front of the Radio Housing. (Figure C) 3 Snap the pocket into the ...

  • Metra Electronics 99-7013 - page 8

    99-7013 KIT ASSEMBL Y 6 B C DOUBLE DIN/ST ACKED ISO UNITS PROVISION Cut and remove the center bar from the Radio Housing. (Figure A) 1 Snap the Double DIN Brackets to the inside edge of the Radio Housing. (Figure B) 2 Slide the Double DIN or stacked ISO unit(s) into the bracket/radio housing assembly and secure the Double DIN or stacked ISO unit(s) ...

  • Metra Electronics 99-7013 - page 9

    7 99-7013 FINAL ASSEMBL Y FINAL ASSEMBL Y (A) Strip wire ends back 1/2" B) T wist ends together C) Solder D) T ape A B C D Locate the factory wiring har ness in the dash. Metra r ecommends using the proper mating adapter and making connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short ...

  • Metra Electronics 99-7013 - page 10

    99-7013 NOTES 8 ...

  • Metra Electronics 99-7013 - page 11

    99-7013 NOTES 9 ...

  • Metra Electronics 99-7013 - page 12

    99-7013 INSTRUCTIONS 1-800-221-0932 REV . 04/21/10 © COPYRIGHT 2007-2010 METRA ELECTRONICS CORPORA TION INST99-7013 www .metr aonline.com ...

メーカー Metra Electronics カテゴリー Car Stereo System

Metra Electronics 99-7013のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 99-7013の取扱説明書
- Metra Electronicsの製品カード
- パンフレット
- またはMetra Electronics 99-7013の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Metra Electronics 99-7013の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Metra Electronics 99-7013の取り付け説明書、サービスマニュアル、簡易説明書、またはMetra Electronics 99-7013のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Metra Electronics 99-7013の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Metra Electronics 99-7013デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがMetra Electronics 99-7013を使用するのを助ける技術的文書のことです。説明書は通常、全てのMetra Electronics 99-7013ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Metra Electronicsの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Metra Electronics 99-7013の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははMetra Electronics 99-7013の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Metra Electronics 99-7013に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Metra Electronics 99-7013デバイスの基本機能を使うにあたってのヒント。 Metra Electronics 99-7013のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Metra Electronics 99-7013に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるMetra Electronics 99-7013のメーカー/サービスへの連絡先に関する情報。

Metra Electronics 99-7013についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもMetra Electronics 99-7013の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがMetra Electronics 99-7013で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)