-
Telenetics 202T, MIU202T - page 1
Document No. 49 - 0002 - 011 Rev. A Installation, Operation & Diagnostics for the MIU202T Industrial Grade, Bell 202T Standalone Modem ...
-
Telenetics 202T, MIU202T - page 2
Document No. 49 - 0002 - 011 Rev. A Telenetics Corporation ARC Electronics 800 - 926 - 0226 ...
-
Telenetics 202T, MIU202T - page 3
MIU202T Installation, Operation & Diagnostics Edition: April 4, 1998 Page 1 TABLE OF CONTENTS 1. STANDARDS ......................................................................................................... 2 2. PRODUCT OVERVI EW ....................................................................................... 3 3. GENERAL PRODUCT S ...
-
Telenetics 202T, MIU202T - page 4
MIU202T Installation, Operation & Diagnostics Edition: April 4, 1998 Page 2 1. STANDARDS Meets FCC Rules Part J, Subpart 15, Class A for radiated emissions. ...
-
Telenetics 202T, MIU202T - page 5
MIU202T Installation, Operation & Diagnostics Edition: April 4, 1998 Page 3 2. PRODUCT OVERVIEW The MIU202T is an industrial grade B ell202T modem for connection to unconditioned and conditioned, voice grade, type 3002 two or four - wire leased lines and metallic lines (eg; pilot wires). It can be powered from a wide range of AC and DC power su ...
-
Telenetics 202T, MIU202T - page 6
MIU202T Installation, Operation & Diagnostics Edition: April 4, 1998 Page 4 3. GENERAL PRODUCT SPECIFICATIONS Dimensions: 5.3 x 4.0 x 1.375 inches Weight: 1 lb Voltage Supply : Standard Model: 40 to 270VDC 40 to 270VAC, 50/60Hz LV Model (Suffix “ - LV”): 9 to 36VDC Current Requirements : 12VDC 24VDC 125VDC 120VAC 220VAC 65mA 27mA 7.5mA 6.5m ...
-
Telenetics 202T, MIU202T - page 7
MIU202T Installation, Operation & Diagnostics Edition: April 4, 1998 Page 5 4. MODEM SPECIFICATIONS Modulation: Bell202T Modulation Type: FSK Synch/Async: Asynchronous Only Data Rate: 0 – 1200bps Transmit Frequency: Mark: 1200Hz Space: 2200Hz Error Correction: None Data Compression: None Data Modulation Connectivity: Using 16ms Polling Test 9 ...
-
Telenetics 202T, MIU202T - page 8
MIU202T Installation, Operation & Diagnostics Edition: April 4, 1998 Page 6 Other Features Receiver Equalization: Compromise Equalization Self Test Diagnostic s: None Local Analog Loopback: See Section 13 Local Digital Loopback: See Section 13 Remote Analog Loopback See Section 13 Remote Digital Loopback See Section 13 Anti - Streaming: OFF or ...
-
Telenetics 202T, MIU202T - page 9
MIU202T Installation, Operation & Diagnostics Edition: April 4, 1998 Page 7 5. ANALOG LINE SPECIFICATIONS The MIU202T contains analog circuitry for connection to the public conditioned or unconditioned, Bell type 3002, 2 or 4 - wire, full duplex voice grade leased lines or metallic lines (eg; pilot wires). The MIU202T will also interface to Pow ...
-
Telenetics 202T, MIU202T - page 10
MIU202T Installation, Operation & Diagnostics Edition: April 4, 1998 Page 8 6. ANALOG MICROWAVE INTERFACE The MIU202Tis designed to interface to a Microwave radio voice channel network with the following specifications: Phase Jitter (10 to 300Hz)1 degree peak - to - peak, max. F requency Response: 300 - 3400Hz - 3, +0.7 dB 400 - 3000Hz - 1, +0. ...
-
Telenetics 202T, MIU202T - page 11
MIU202T Installation, Operation & Diagnostics Edition: April 4, 1998 Page 9 Crosstalk (unintelligible): Adjacent channel 28dBrnc0 maximum (24 455B weighted noise at 0 dBmO dBrnc0 typical). Intra - channel 28 dBr nc0, maximum (18 dBrnc0, typical) (1KHz test tone at 0 dBmO) Out of Band Signalling: Frequency 3825 Hz Level - 20 dBmO Pulse speed (30 ...
-
Telenetics 202T, MIU202T - page 12
MIU202T Installation, Operation & Diagnostics Edition: April 4, 1998 Page 10 7. POWER CONNECTIONS ...
-
Telenetics 202T, MIU202T - page 13
MIU202T Installation, Operation & Diagnostics Edition: April 4, 1998 Page 11 8. SERIAL DATA PORT PIN - OUTS ...
-
Telenetics 202T, MIU202T - page 14
MIU202T Installation, Operation & Diagnostics Edition: April 4, 1998 Page 12 9. DIP SWITCH FUNCTIONS IMPORTANT NOTE: Invert modem to view dip switches as shown above Table 1 Switch Function ON OFF Switch 1 Transmit Analog (TxA) Signal Level 0 dBm - 10 dBm Switch 2 Anti - Streaming 45 secs OFF Switch 3 Received Analog (RxA) Signal Level - 33 dBm ...
-
Telenetics 202T, MIU202T - page 15
MIU202T Installation, Operation & Diagnostics Edition: April 4, 1998 Page 13 Table 2: RTS/CTS Delay Time 2 Wire 4 Wire Switche d Carrie r Constan t Carri e r Switch 4 Switch 5 Switch 9 Soft Carrier RTS/CTS Delay Time NO YES YES YES ON ON OFF 50 ms YES NO YES NO ON ON ON 50 ms NO YES YES NO ON ON ON 50 ms YES NO YES NO ON ON OFF 50 ms NO YES YES ...
-
Telenetics 202T, MIU202T - page 16
MIU202T Installation, Operation & Diagnostics Edition: April 4, 1998 Page 14 10. MODEM CONFIGURATION The following table provides the Dip Switch settings required for most modem application configurations: Dip Switch Setting 1 2 3 4 5 6 7 8 9 4 - Wire Point - to - Point ON ON ON ON 4 - Wire Multi - Point Master ON ON ON ON 4 - Wire Multi - Poin ...
-
Telenetics 202T, MIU202T - page 17
MIU202T Installation, Operation & Diagnostics Edition: April 4, 1998 Page 15 11. LED INDICATOR ...
-
Telenetics 202T, MIU202T - page 18
MIU202T Installation, Operation & Diagnostics Edition: April 4, 1998 Page 16 12. OUTLINE DRAWING & MOUNTING ...
-
Telenetics 202T, MIU202T - page 19
MIU202T Installation, Operation & Diagnostics Edition: April 4, 1998 Page 17 13. DIAGNOSTICS The following pages provide hardware techniques for diagnosing communication problems and thereby isolating the problem at the local modem, the remote modem or the interco nnecting line. (a) LOCAL ANALOG LOOPBACK (Figure 2) Requires a loop back cable wi ...
-
Telenetics 202T, MIU202T - page 20
MIU202T Installation, Operation & Diagnostics Edition: April 4, 1998 Page 18 Test 3: Received Signal Level Set Dip Switch 1 OFF (TxA = - 10dBm) and Dip Switch 3 OFF (RxA = - 43dBm). CD will be ON. Run a test message at TxD and verify that the same message is received at RxD with no data errors. Test 4: Repeat Test 3 for various RTS/CTS delay ti ...
-
Telenetics 202T, MIU202T - page 21
MIU202T Installation, Operation & Diagnostics Edition: April 4, 1998 Page 19 (c) REMOTE DIGITAL L OOPBACK – 4/Wire Network (Figure 5) Configure both the local and remote modems as follows: Switch 1 = ON (TxA = 0dBm) Switch 3 = ON (RxA = - 33dBm) Switch 4 = OFF (RTS/CTS = 35ms) Switch 5 = ON (RTS/CTS = 35ms) Switch 6 = ON (Constant Carrier mod ...
-
Telenetics 202T, MIU202T - page 22
MIU202T Installation, Operation & Diagnostics Edition: April 4, 1998 Page 20 (d) LINE DIAGNOSTICS (i) Typical modem configuration for 4 - wire Point - to - Point system… Switch 1 = ON (TxA = 0dBm) Switch 3 = ON (RxA = - 33dBm) Switch 4 = OFF (RTS/CTS = 1ms) Switch 5 = OFF (RTS/CTS = 1ms) Switch 6 = ON (Constant Carrier mode). Switch 7 = OFF ( ...
-
Telenetics 202T, MIU202T - page 23
MIU202T Installation, Operation & Diagnostics Edition: April 4, 1998 Page 21 ...
-
Telenetics 202T, MIU202T - page 24
MIU202T Installation, Operation & Diagnostics Edition: April 4, 1998 Page 22 ...
-
Telenetics 202T, MIU202T - page 25
MIU202T Installation, Operation & Diagnostics Edition: April 4, 1998 Page 23 ...
-
Telenetics 202T, MIU202T - page 26
MIU202T Installation, Operation & Diagnostics Edition: April 4, 1998 Page 24 NOTES: ...
Do you have a question concerning Telenetics 202T, MIU202T?
Use the form below
If you did not solve your problem by using a manual Telenetics 202T, MIU202T, ask a question using the form below. If a user had a similar problem with Telenetics 202T, MIU202T it is likely that he will want to share the way to solve it.