English dropdown-ico

Manual Fujitsu MB3887

32 pages 0.35 mb
Download

Go to site of 32

Summary
  • Fujitsu MB3887 - page 1

    DS04-27709-3E FUJITSU SEMICONDUCT OR DA T A S H E E T ASSP F or P o wer Supply Applications (Secondar y batter y) DC/DC Con ver ter IC f or Char ging Li-ion batter y MB3887 ■ DESCRIPTION The MB3887 is a DC/DC conv er ter IC suitable f or down-conv ersion, using pulse-width (PWM) charging and enabling output v oltage to be set to any desired le ve ...

  • Fujitsu MB3887 - page 2

    MB3887 2 (Continued) • Output v oltage setting using external resistor : 1 cell to 4 cells • High efficiency : 96 % (VIN = 19 V, V o = 16.8 V) • Wide range of oper ating supply v oltages : 8 V to 25 V • Output v oltage setting accuracy : 4.2 V ± 0.74 % (T a = − 10 ° C to + 85 ° C , per cell) • Charging current accuracy : ± 5 % • B ...

  • Fujitsu MB3887 - page 3

    MB3887 3 ■ PIN ASSIGNMENT (TOP VIEW) (FPT-24P-M03) 1 2 3 4 5 6 7 8 9 10 11 12 − INC2 : OUTC2 : + INE2 : − INE2 : FB2 : VREF : FB1 : − INE1 : + INE1 : OUTC1 : OUTD : − INC1 : 24 23 22 21 20 19 18 17 16 15 14 13 : + INC2 : GND : CS : VCC (O) : OUT : VH : VCC : RT : − INE3 : FB3 : CTL : + INC1 ...

  • Fujitsu MB3887 - page 4

    MB3887 4 ■ PIN DESCRIPTION Pin No. Symbol I/O Descriptions 1 − INC2 I Current detection amplifier (Current Amp2) input terminal. 2 OUTC2 O Current detection amplifier (Current Amp2) output terminal. 3 + INE2 I Error amplifier (Error Amp2) non-inverted input terminal. 4 − INE2 I Error amplifier (Error Amp2) inverted input terminal. 5 FB2 O Err ...

  • Fujitsu MB3887 - page 5

    MB3887 5 ■ BLOCK DIA GRAM + − − + 8 10 13 12 9 + − − + 4 2 24 1 3 × 20 × 20 + + + − 5 20 21 19 − + + + − 11 16 22 17 6 23 14 18 <Current Amp1> <Error Amp1> 7 VREF <Current Amp2> <Error Amp2> VREF <Error Amp3> VREF VREF VREF 5.0 V 4.2 V 10 µ A 15 <SOFT> 2.5 V 1.5 V <OUT> <UVLO> <O ...

  • Fujitsu MB3887 - page 6

    MB3887 6 ■ ABSOLUTE MAXIMUM RA TINGS * : The package is mounted on the dual-sided epo xy board (10 cm × 10 cm) . W ARNING: Semiconductor de vices can be per manently damaged by application of stress (v oltage, current, temperature , etc.) in e xcess of absolute maximum ratings. Do not e xceed these ratings. P arameter Symbol Conditions Rating Un ...

  • Fujitsu MB3887 - page 7

    MB3887 7 ■ RECOMMENDED OPERA TING CONDITIONS W ARNING: The recommended operating conditions are required in order to ensure the normal operation of the semiconductor de vice. All of the de vice’ s electr ical characteristics are warranted when the de vice is operated within these ra nges. Always use semiconductor devices within their recommende ...

  • Fujitsu MB3887 - page 8

    MB3887 8 ■ ELECTRICAL CHARA CTERISTICS (T a = + 25 ° C, VCC = 19 V, VCC (O) = 19 V, VREF = 0 mA) * : Standard design v alue. (Continued) Pa r a m e t e r Sym- bol Pin No. Conditions Va l u e Unit Min T yp Max 1. Reference voltage block [REF] Output voltage V REF1 6T a = + 25 ° C 4.967 5.000 5.041 V V REF2 6T a = − 10 ° C to + 85 ° C 4.95 5. ...

  • Fujitsu MB3887 - page 9

    MB3887 9 (T a = + 25 ° C, VCC = 19 V, VCC (O) = 19 V, VREF = 0 mA) * : Standard design v alue (Continued) Pa r a m e t e r Sym- bol Pin No. Conditions Va l u e Unit Min T yp Max 5-2. Error amplifier block [Error Amp3] Threshold voltage V TH1 16 FB3 = 2 V, Ta = + 25 ° C 4.183 4.200 4.225 V V TH2 16 FB3 = 2 V, Ta = − 10 ° C to + 85 ° C 4.169 4. ...

  • Fujitsu MB3887 - page 10

    MB3887 10 (T a = + 25 ° C, VCC = 19 V, VCC (O) = 19 V, VREF = 0 mA) * : Standard design v alue (Continued) Pa r a m e t e r Sym- bol Pin No. Conditions Va l u e Unit Min T yp Max 6. Current detection amplifier block [Current Amp1, Current Amp2] Current detection voltage V OUTC1 2, 10 + INC1 = + INC2 = 3 V to VCC, ∆ Vin = − 100 mV 1.9 2.0 2.1 V ...

  • Fujitsu MB3887 - page 11

    MB3887 11 (Continued) (T a = + 25 ° C, VCC = 19 V, VCC (O) = 19 V, VREF = 0 mA) * : Standard design v alue Pa r a m e t e r Sym- bol Pin No. Conditions Va l u e Unit Min T yp Max 8. Output block [OUT] Output source current I SOURCE 20 OUT = 13 V, Duty ≤ 5 % (t = 1 / f OSC × Duty) − 400*  mA Output sink current I SINK 20 OUT = 19 V, Duty ...

  • Fujitsu MB3887 - page 12

    MB3887 12 ■ TYPICAL CHARA CTERISTICS (Continued) 6 5 4 3 2 1 0 0 5 10 15 20 25 Ta = + 25 ° C CTL = 5 V 6 5 4 3 2 1 0 0 5 10 15 20 25 Ta = + 25 ° C CTL = 5 V VREF = 0 mA 6 5 4 3 2 1 0 0 5 10 15 20 25 30 Ta = + 25 ° C VCC = 19 V CTL = 5 V 5.08 5.06 5.04 5.02 5.00 4.98 4.96 4.94 4.92 − 40 − 20 0 20 40 60 80 100 VCC = 19 V CTL = 5 V 1000 900 8 ...

  • Fujitsu MB3887 - page 13

    MB3887 13 (Continued) 1 M 100 k 10 k 10 100 1000 Ta = + 25 ° C VCC = 19 V CTL = 5 V 340 330 320 310 300 290 280 270 260 0 5 10 15 20 25 Ta = + 25 ° C CTL = 5 V RT = 47 k Ω 320 315 310 305 300 295 290 285 280 275 270 265 260 − 40 − 20 0 20 40 60 80 100 VCC = 19 V CTL = 5 V RT = 47 k Ω 4.25 2.24 4.23 2.22 4.21 4.20 4.19 4.18 4.17 4.16 4.15 ...

  • Fujitsu MB3887 - page 14

    MB3887 14 (Continued) − + 7 8 9 + OUT IN (5) (4) (3) 240 k Ω 2.4 k Ω 10 k Ω 10 k Ω 10 k Ω 10 k Ω Error Amp1 (Error Amp2) 4.2 V VCC = 19 V 1 µ F Ta = + 25 ° C A V φ 40 20 0 − 20 − 40 180 90 0 − 90 − 180 1 k 10 k 100 k 1 M 10 M − + + 15 16 22 + OUT IN 240 k Ω 2.4 k Ω 10 k Ω 10 k Ω 10 k Ω 10 k Ω Error Amp3 4.2 V ...

  • Fujitsu MB3887 - page 15

    MB3887 15 (Continued) 800 700 600 500 400 300 200 100 0 740 − 40 − 20 0 20 40 60 80 100 Power dissipation vs. Ambient temperature Power dissipation P D (mW) Ambient temperature Ta ( ° C) ...

  • Fujitsu MB3887 - page 16

    MB3887 16 ■ FUNCTIONAL DESCRIPTION 1. DC/DC Con ver ter Unit (1) Reference v oltage bloc k (Ref) The ref erence voltage generator uses the v oltage supplied from the VCC ter minal (pin 18) to generate a tem- perature-compensated, stab le voltage (5.0 V T yp) used as the ref erence supply v oltage f or the IC’ s inter nal circuitr y . This ter m ...

  • Fujitsu MB3887 - page 17

    MB3887 17 (7) PWM comparator bloc k (PWM Comp.) The PWM comparator circuit is a v oltage-pulse width conv er ter f or controlling the output duty of the error amplifiers (Error Amp1 to Error Amp3) depending on their output v oltage. The PWM comparator circuit compares the triangular wa ve generated b y the tr iangular w av e oscillator to the error ...

  • Fujitsu MB3887 - page 18

    MB3887 18 3. Soft-Star t Function Soft-start block (SOFT) Connecting a capacitor to the CS ter minal (pin 22) pre v ents r ush currents when the IC is tur ned on. Using an error amplifier f or soft-star t detection makes the soft-star t time constant, being independent of the output load of the DC/DC conv er ter . ■ SETTING THE CHARGING V OL T A ...

  • Fujitsu MB3887 - page 19

    MB3887 19 ■ METHOD OF SETTING THE SOFT -ST ART TIME F or pre venting rush current upon activation of IC, the IC allo ws soft-star t using the capacitor (Cs) connected to the CS ter minal (pin 22) . When CTL ter minal (pin 14) is placed under “H” lev el and IC is activ ated (V CC ≥ UVLO threshold v oltage) , Q2 is tur ned off and the e xter ...

  • Fujitsu MB3887 - page 20

    MB3887 20 ■ A C AD APT OR V OL T A GE DETECTION • With an e xter nal resistor connected to the + INE2 ter minal (pin 3) , the IC enters the dynamically-controlled charging mode to reduce the charge current to keep A C adapter power constant when the par tial potential point A of the A C adapter voltage (VCC) becomes lo wer than the v oltage at ...

  • Fujitsu MB3887 - page 21

    MB3887 21 ■ PR OCESSING WITHOUT USING THE CURRENT AMP When Current Amp is not used, connect the + INC1 ter minal (pin 13) , + INC2 ter minal (pin 24) , − INC1 ter minal (pin 12) , and − INC2 ter minal (pin 1) to VREF, and then lea ve OUTC1 terminal (pin 10) and OUTC2 ter minal (pin 2) open. 24 13 12 1 2 10 6 − INC1 + INC1 + INC2 − INC2 OU ...

  • Fujitsu MB3887 - page 22

    MB3887 22 ■ PR OCESSING WITHOUT USING OF THE ERROR AMP When Error Amp is not used, leav e FB1 ter minal (pin 7) , FB2 ter minal (pin 5) open and connect the − INE1 ter minal (pin 8) and − INE2 ter minal (pin 4) to GND and connect + INE1 ter minal (pin 9) , and + INE2 ter minal (pin 3) , to VREF . 9 5 8 4 7 + INE1 GND + INE2 − INE1 − INE2 ...

  • Fujitsu MB3887 - page 23

    MB3887 23 ■ PR OCESSING WITHOUT USING OF THE CS TERMINAL When soft-star t function is not used, leav e the CS ter minal (pin 22) open. ■ NO TE ON AN EXTERNAL REVERSE-CURRENT PREVENTIVE DIODE • Inser t a rev erse-current prev entive diode at one of the three locations marked * to pre v ent re verse current from the batter y . • When selectin ...

  • Fujitsu MB3887 - page 24

    MB3887 24 ■ APPLICA TION EXAMPLE A B Q1 Output voltage (Battery voltage) is adjustable D1 I1 Battery R8 100 k Ω C10 5600 pF + + + R9 10 k Ω R14 1 k Ω R10 30 k Ω R11 30 k Ω R7 22 k Ω R18 200 k Ω R19 100 k Ω R17 100 k Ω C6 1500 pF C4 0.022 µ F R3 330 k Ω R2 47 k Ω C9 0.1 µ F C7 0.1 µ F C5 0.1 µ F C2 100 µ F C3 100 µ F C1 ...

  • Fujitsu MB3887 - page 25

    MB3887 25 ■ P ARTS LIST Note : VISHA Y SILICONIX : VISHA Y Inter technolog y , Inc. ROHM : R OHM CO ., L TD . TDK : TDK Cor poration SANY O : SANY O Electric Co ., Ltd. KY OCERA : K yocera Corporation MURA T A : Murata Man u f actur ing Co ., Ltd. SEIDEN TECHNO : SEIDEN TECHNO CO ., L TD . KO A : KO A C o r p o r a t i o n ssm : SUSUMU Co ., Ltd. ...

  • Fujitsu MB3887 - page 26

    MB3887 26 ■ REFERENCE D A T A (Continued) 100 98 96 94 92 90 88 86 84 82 80 10 m 100 m 1 10 Ta = + 25 ° C VIN = 19 V BA TT charge voltage = set at 12.6 V SW = ON Efficiency η (%) = (V BA TT × I BA TT ) / (V IN × I IN ) × 100 100 98 96 94 92 90 88 86 84 82 80 02 46 8 1 0 1 2 1 4 1 6 Ta = + 25 ° C VIN = 19 V BA TT charge voltage = set at 12.6 ...

  • Fujitsu MB3887 - page 27

    MB3887 27 (Continued) 100 98 96 94 92 90 88 86 84 82 80 10 m 100 m 1 10 Ta = + 25 ° C VIN = 19 V BA TT charge voltage = set at 16.8 V SW = ON Efficiency η (%) = (V BA TT × I BA TT ) / (V IN × I IN ) × 100 100 98 96 94 92 90 88 86 84 82 80 0 2 4 6 8 1 0 1 21 4 1 6 1 82 0 Ta = + 25 ° C VIN = 19 V BA TT charge voltage = set at 16.8 V SW = ON Eff ...

  • Fujitsu MB3887 - page 28

    MB3887 28 (Continued) 100 0 − 100 15 10 5 0 V BA TT (mV) V D (V) Ta = + 25 ° C VIN = 19 V BA TT = 1.5 A 98 mVp-p 012345 6 7 8 9 1 0 ( µ s) V D V BA TT 100 0 − 100 15 10 5 0 V BA TT (mV) V D (V) Ta = + 25 ° C VIN = 19 V BA TT = 3.0 A 98 mVp-p V D V BA TT 012 3 456 789 1 0 ( µ s) 100 0 − 100 15 10 5 0 V BA TT ( mV) V D (V) Ta = + 25 ° C VI ...

  • Fujitsu MB3887 - page 29

    MB3887 29 (Continued) 20 10 0 4 2 0 5 0 V CTL (V) V CS (V) V BA TT (V) 0 2 4 6 8 1 01 21 41 61 82 0 (ms) Ta = + 25 ° C, VIN = 19 V BA TT = 12 Ω V BA TT V CTL ts = 10.4 ms V CS 20 10 0 4 2 0 5 0 V CTL (V) V CS (V) V BA TT (V) 0 2 4 6 8 1 01 21 41 61 82 0 (ms) Ta = + 25 ° C VIN = 19 V BA TT = 12 Ω V BA TT V CTL V CS 20 10 0 4 2 0 5 0 V CTL (V) ...

  • Fujitsu MB3887 - page 30

    MB3887 30 ■ USA GE PRECA UTIONS • Printed circuit board ground lines should be set up with consideration f or common impedance. • T ake appropriate static electr icity measures. • Containers f or semiconductor mater ials should hav e anti-static protection or be made of conductive material. • After mounting, printed circuit boards should ...

  • Fujitsu MB3887 - page 31

    MB3887 31 ■ P A CKA GE DIMENSION 24-pin plastic SSOP (FPT-24P-M03) Note1: Pins width and pins thickness include plating thickness. Note2: * This dimension does not include resin protrusion. Dimensions in mm (inches) . C 2001 FUJITSU LIMITED F24018S-c-3-4 7.75±0.10(.305±.004) 5.60±0.10 7.60±0.20 (.220±.004) (.299±.008) * 0.10(.004) 11 2 13 2 ...

  • Fujitsu MB3887 - page 32

    MB3887 FUJITSU LIMITED All Rights Reserved. The contents of this document are subject to change without notice. Customers are advised to consult with FUJITSU sales representatives before ordering. The information and circuit diagrams in this document are presented as examples of semiconductor device applications, and are not intended to be incorpor ...

Manufacturer Fujitsu Category Power Supply

Documents that we receive from a manufacturer of a Fujitsu MB3887 can be divided into several groups. They are, among others:
- Fujitsu technical drawings
- MB3887 manuals
- Fujitsu product data sheets
- information booklets
- or energy labels Fujitsu MB3887
All of them are important, but the most important information from the point of view of use of the device are in the user manual Fujitsu MB3887.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Fujitsu MB3887, service manual, brief instructions and user manuals Fujitsu MB3887. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Fujitsu MB3887.

Similar manuals

A complete manual for the device Fujitsu MB3887, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Fujitsu MB3887 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Fujitsu MB3887.

A complete Fujitsu manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Fujitsu MB3887 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Fujitsu MB3887, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Fujitsu MB3887, that we can find in the current document
3. Tips how to use the basic functions of the device Fujitsu MB3887 - which should help us in our first steps of using Fujitsu MB3887
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Fujitsu MB3887
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Fujitsu MB3887 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Fujitsu MB3887?

Use the form below

If you did not solve your problem by using a manual Fujitsu MB3887, ask a question using the form below. If a user had a similar problem with Fujitsu MB3887 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)