English dropdown-ico

Manual Clenaware Sovereign 45

35 pages Not applicable
Download

Go to site of 35

Summary
  • Clenaware Sovereign 45 - page 1

    www.clenaware.co.uk Owner’s Manual Sovereign Mark 5 Glass Washing Machine WEE/DE2076RU Machines are manufactured to ISO 9001 : 2 008 ...

  • Clenaware Sovereign 45 - page 2

    www.clenaware.co.uk Index Sovereign Glass Washer Op erating Inst ructions .......................................................... 3 Preparat ion .......................................................................................................... 3 Fillin g .................................................................................... ...

  • Clenaware Sovereign 45 - page 3

    www.clenaware.co.uk Sovereign Glass Washer Operating Instructions Preparation  Ensure that the machine inte rior is clean and soil-free, and that the bottom spray bar rotates freely, jets are clean and correctly located.  Check that the upper ri nse dome is in place.  Ensure that all four filters are in position in the wash tank trough: Pr ...

  • Clenaware Sovereign 45 - page 4

    www.clenaware.co.uk Filling  When the machine is switched on, a fi ll heat sequence will be performed as follows:  The rinse tank will fi ll with water.  The drain pump will operate to vaca te any water from the wash ta nk.  The Fill/Ready Lamp will be illuminated orange.  The Start Switch will be illuminated green (rotating).  On ...

  • Clenaware Sovereign 45 - page 5

    www.clenaware.co.uk Standby Mode  Pressing the ‘SELECT Switch’ will step through the cycle op tions as follows: Glass R e n o v a t e P l a s t i c ( o n l y i f e n a b l e d b y a n e n g i n e e r ) C l o s e d o w n  The appropriate indicator w ill be illuminated blue. GLASS CYCLE is the default cycle and used for washing normal glass ...

  • Clenaware Sovereign 45 - page 6

    www.clenaware.co.uk Washing Glass and Plastic Note that the Glass and Plastic cycles are very similar in op eration. The differences are a higher rinse temperature and increased rinse-aid dose on the plastic cycle.  Fill a basket with inverted glasses havi ng first emptied out any liquid or solid waste elsewhere. Open the door and slide the bask ...

  • Clenaware Sovereign 45 - page 7

    www.clenaware.co.uk Renovate Cycle This cycle is used for the pr eparation of new glassware, th e renovating of stained or greasy glassware, and is also recommend ed for cleaning the machine wash tank interior.  Open the door and add a me asure of Renovate Powder to the top of the Main Filter (avoid contact wi th eyes, hands and face).  Fill ...

  • Clenaware Sovereign 45 - page 8

    www.clenaware.co.uk Closedown Cycle  From Standby Mode, select the Closedow n Cycle and press the START Switch to start the cycle: At any other time (during the fill/heat sequ ence, during a wash cycle, or whilst the machine is in an error condition), press th e SELECT Switch (the Closedown Lamp will flash) and press the START Switch. Th is will ...

  • Clenaware Sovereign 45 - page 9

    www.clenaware.co.uk Chemical Injection and Warnings Detergent & Rinse-Aid Detergent and Rinse-Aid is au tomatically injected during each washing cycle. The amount of chemical injected is dependant on site conditions, and can be adjusted by a n engineer. The default setting is 300:1 for de tergent and 3000:1 for rinse-aid. A bottle of rinse-aid ...

  • Clenaware Sovereign 45 - page 10

    www.clenaware.co.uk Spraybar Rotation Warning Poor wash quality will result from the lack of rotation of the spray-bar. The machi ne incorporates a spray-bar rotation sensor and will hi ghlight a problem by use of a warning lamp. Spray bar rotation is continua lly monitored du ring the wash and rinse periods of a wash cycle. If rotation is detected ...

  • Clenaware Sovereign 45 - page 11

    www.clenaware.co.uk Other Features Energy Saving In Standby Mode the rinse water temperature is held at a lower valu e than that requi red for the cycle rinse. The shortfal l in rinse temperature is made up during the wash part of a cycle. In this way, energy is no t needlessly wasted. The standby temperature will de pend on the model, th e cycle t ...

  • Clenaware Sovereign 45 - page 12

    www.clenaware.co.uk Daily Maintenance IMPORTANT! Ensure that the electrical an d water supplies are switched off while carrying out the following procedures. This appliance must not be cleaned with a water jet. Refer to Exploded Diagram below for help with maintenance and spares.  At the end of each sessi on, open the machine door and remove the ...

  • Clenaware Sovereign 45 - page 13

    www.clenaware.co.uk  Remove the Main Tray Filter which cove rs the wash tank trough, and the Drum Filter which covers the wash outlet ho le. Brush them clean under running w ater to ensure that all partic les and fibres are removed.  Use a damp cloth to wipe cl ean the wash tank trough.  Unscrew and remove the two Flat Disc Filters and bru ...

  • Clenaware Sovereign 45 - page 14

    www.clenaware.co.uk Vital Parts To Be Regularly Cleaned / Maintained RINSE ARM & SPINDLE ASSY CS-B0704 (SOVEREIGN 45) CS-B0705 (SOVEREIGN 50) RINSE SPRAY-JET CS-D0719 (BLUE) O-RING CS - X0747 WASH SPRAY-JET CS-D0718 (WHITE) O-RING CS-X0747 WASH ARM & SPINDLE ASSY CS-B0701 (SOVEREIGN 45) CS-B0702 (SOVEREIGN 50) ...

  • Clenaware Sovereign 45 - page 15

    www.clenaware.co.uk MAIN TRAY FILTER CS-D0316 DRUM FILTER CS - B0304 FLAT DISC FILTER (WASH) CS - F0333 FLAT DISC FILTER (DRAIN) CS - F0332 ...

  • Clenaware Sovereign 45 - page 16

    www.clenaware.co.uk Caring For Your Sovereign Glass Washer Observance of the following will ensure maximum efficiency fr om your machine: Please “do” the following: Glass Preparation  Remove all solid material such as cock tail sticks, fruit p eel and pips etc.  Ensure that glasses used fo r speciality coffees or other drinks containing c ...

  • Clenaware Sovereign 45 - page 17

    www.clenaware.co.uk  Ensure that a Water Softener, where fitted, is regenerated regularly.  Ensure that the Fill/Ready Lamp is green before starting a cycle.  Ensure that a wash cycle is fully completed before removal of glasses. On completion of a cycle, the Start Switch wi ll stop rotating, and there will be five bleeps by the audible al ...

  • Clenaware Sovereign 45 - page 18

    www.clenaware.co.uk Simple Fault Finding Should a problem develop with your Sovereig n machine, please consult the following fault-finding procedures be fore calling for a ssistance. Service Lamp Flashes  The Sovereign machine is designed to keep operating re gardless of most functional errors that might occur. For example, for an internal heate ...

  • Clenaware Sovereign 45 - page 19

    www.clenaware.co.uk  If a Water Softener is fitted, check th at the softener is not regenerating.  Call for assistance. Machine Will Not Drain  Check for blocked drain filter.  Call for assistance. Machine Filled Okay, But Washtank Is Empty  Check for water siphoning ou t of the machine due to th e Drain Outlet Hose being pushed too ...

  • Clenaware Sovereign 45 - page 20

    www.clenaware.co.uk  Check that chemical suction tubes are correctly in positi on in the containers. The ‘clear’ tube should be fed by t he detergent container, and the ‘blue’ tube fe d by the Rinse-Aid container.  Ensure that quality chemicals desi gned for glass washing are in use.  Check that the water softener (where fitte d) i ...

  • Clenaware Sovereign 45 - page 21

    www.clenaware.co.uk  The Sovereign machine is equipped with a Renovate Cycle. Glasses can be put through a Renovate Cycle (u sing Renovate Powder) to remove any build-up of contamination. Renovating glassware is recommended at regular intervals. Brand new glassware should also be renovated prior to using.  Call for assistance. Glasses “Smea ...

  • Clenaware Sovereign 45 - page 22

    www.clenaware.co.uk Machine Noisy In Wash Cycle  Check that the wash tank filt er has been fitted properly.  Check that there is wa ter in the wash tank.  Check the wash tank filters for blockages.  Call for assistance. Excessive Foam In Cabinet  Ensure that quality chemicals desi gned for glass washing are in use.  Check that che ...

  • Clenaware Sovereign 45 - page 23

    www.clenaware.co.uk Machine Errors If the machine experiences a major error, this is indicated by the Service Lamp flashing red. Description of errors: Overfill Error (code ‘1’)  The Service Lamp will flash at a rate of – 1 F lash and 1 Pause  The machine will be unusable.  Closedown the machine and call for an engineer. Overfill Err ...

  • Clenaware Sovereign 45 - page 24

    www.clenaware.co.uk Refill Error (code ‘4’)  The Service Lamp will flash at a rate of – 4 F lashes and 1 Pause  The machine will be unusable.  Closedown the machine and call for an engineer. Rinse Timeout Error (code ‘5’)  The Service Lamp will flash at a rate of – 5 F lashes and 1 Pause  The machine will be unusable.  ...

  • Clenaware Sovereign 45 - page 25

    www.clenaware.co.uk Sovereign Glass Washer Installation Electrical Connection IMPORTANT: Electrical connection must be carried out by a competent electrical engineer WARNING: THIS APPLIANCE MUST BE EARTHED The wires in the mains lead supplied are co loured in accordance with the following code: G r e e n / Y e l l o w - E a r t h B l u e - N e u t ...

  • Clenaware Sovereign 45 - page 26

    www.clenaware.co.uk 30 AMP (Recommended) Sovereign machines are supplied from the factory internally wired for 30 amp (5.4 kW) operation and fitted with a 4m m² Mains Cable. Connection must b e ma de t o a 30 amp supply. 13 AMP (Optional) Sovereign machines can be de-rated for operatio n on a 13 Amp supply by a competent engineer. This modificatio ...

  • Clenaware Sovereign 45 - page 27

    www.clenaware.co.uk Electrical Ratings Voltage 230 - 240 V 50Hz Input (W) 5500 (as supplie d) or 3000 (de-rated) Current (A) 24 (as supplie d) or 13 (de-rated) Water Connection Sovereign machine can be connected to mains or storage water. The use of cold water supply is recommended. Water requirements:  Hot or Cold 50 – 1000 kPa (0.5-10 bar) @ ...

  • Clenaware Sovereign 45 - page 28

    www.clenaware.co.uk Siting The machine must be sited on a sound leve l surface, with adeq uate clearance for servicing. Allow 50mm extra width and hei ght clearance to ensure ventilatio n around the machine, and aid servicing. Be sure to provi de allowance for water, drain, and electrical connections, and for the positionin g of two 5lt Chem ical B ...

  • Clenaware Sovereign 45 - page 29

    www.clenaware.co.uk These machines incorporate integral Break Tanks which have a T ype ‘A’ Airgap which comply with the requirements of WRC IRN 001 (Category ‘5’ Risk). The machine can be connected to storage, or di rect to Mains Water Supply. If the Water Hardness exceeds 8° Clark or 120 mg/l (ppm), chemicals designed for hard water must ...

  • Clenaware Sovereign 45 - page 30

    www.clenaware.co.uk Clenaware Systems Ltd reserve the right to amend specifications WEEE This equipment contains elect rical and electronic components. At the end of it’s life, this equipment should not be mixed with general waste during disposal. For proper treatment, recove ry and recycling, please take this equipment to a de signated recycling ...

  • Clenaware Sovereign 45 - page 31

    www.clenaware.co.uk Service And Warranty Warranty All Clenaware Systems ma chines are covered by a 12 month gua rantee. Clenaware Systems Ltd guarantee that any and all products manufactured and marketed under the Clenaware Systems name and used in the correct way are free from defects in material and/or workmanship for a period of 12 months from t ...

  • Clenaware Sovereign 45 - page 32

    www.clenaware.co.uk 6: A maintenance service has been carri ed out by Clenaware Systems or an approved / nominate d agent at 12 months from purchase/installatio n. This is chargeable to the customer. 7: That chemicals used during normal operating are those recommended and purchased from Clenaware Systems or an approved / nominated agent. The Clenaw ...

  • Clenaware Sovereign 45 - page 33

    www.clenaware.co.uk Service Warranty 1: All warranty service is performed by Clenaware Systems or an approved / nominated agent. 2: Warranty service is performed Monday to Friday and between the hours of 09.00 and 17.30. 3: All warranty claims should be logged by calling : 01933 666244 Please have the following details to hand to speed up the proce ...

  • Clenaware Sovereign 45 - page 34

    www.clenaware.co.uk Disclaimer 1: Installation and commissioning of th e Clenaware Systems machines should be carried out by Clenaware Systems or an approved / nominated age nt in accordance with the Clenawar e Systems requirements as detailed in the user manual. Failure to install and commi ssion a machine in line with these requirements can inval ...

  • Clenaware Sovereign 45 - page 35

    www.clenaware.co.uk CLENAWARE SYSTEMS LTD Main Office : +44 (0) 1933 666244 Fax: +44 (0) 1933 665 584 Web: www.clenaware.co.uk Email: info@clenaware.co.uk Main Office Address The Wagon Hovel Strixton Manor Business Centre Strixton. Wellingborough Northants. NN29 7PA Factory Address 30 Huxley Close Park Farm Industrial Estate Wellingborough Northant ...

Manufacturer Clenaware Category Dishwasher

Documents that we receive from a manufacturer of a Clenaware Sovereign 45 can be divided into several groups. They are, among others:
- Clenaware technical drawings
- Sovereign 45 manuals
- Clenaware product data sheets
- information booklets
- or energy labels Clenaware Sovereign 45
All of them are important, but the most important information from the point of view of use of the device are in the user manual Clenaware Sovereign 45.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Clenaware Sovereign 45, service manual, brief instructions and user manuals Clenaware Sovereign 45. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Clenaware Sovereign 45.

Similar manuals

A complete manual for the device Clenaware Sovereign 45, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Clenaware Sovereign 45 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Clenaware Sovereign 45.

A complete Clenaware manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Clenaware Sovereign 45 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Clenaware Sovereign 45, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Clenaware Sovereign 45, that we can find in the current document
3. Tips how to use the basic functions of the device Clenaware Sovereign 45 - which should help us in our first steps of using Clenaware Sovereign 45
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Clenaware Sovereign 45
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Clenaware Sovereign 45 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Clenaware Sovereign 45?

Use the form below

If you did not solve your problem by using a manual Clenaware Sovereign 45, ask a question using the form below. If a user had a similar problem with Clenaware Sovereign 45 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)