English dropdown-ico

Manual LevelOne GSW-2493

114 pages 1.32 mb
Download

Go to site of 114

Summary
  • LevelOne GSW-2493 - page 1

    GSW-2493 4-slot modularized L2 SNMP Switch User Guide ...

  • LevelOne GSW-2493 - page 2

    ...

  • LevelOne GSW-2493 - page 3

    Contents 1. INTRO DUCTION ...................................................................................................... 1 Featur es ....................................................................................................................... 1 Software F eatures .................................................................... ...

  • LevelOne GSW-2493 - page 4

    About Web-bas ed Managem ent ................................................................................. 60 Preparing for W eb Managem ent ................................................................................. 60 Online He lp ........................................................................................................... ...

  • LevelOne GSW-2493 - page 5

    Diagnosing LED Indicato rs ....................................................................................... 105 　 Cablin g ................................................................................................ 105 7. TECHNICAL SP ECIFICAT ION ............................................................................ 106 ...

  • LevelOne GSW-2493 - page 6

    ...

  • LevelOne GSW-2493 - page 7

    1 1. Introduction LevelOne GSW-2493, 4-slot intelli gent chassis switch, is a modular switch that can be used to build high-performance switched workgroup networks. This switch is a store-and-forward device that offers low latency for high-speed networking. The Switch is targeted at workgroup, department or backbone computing environment. The GSW-2 ...

  • LevelOne GSW-2493 - page 8

    2  Stack management via one IP addre ss, easy management by Web GUI  IGMP support for Multi Media application  Support IEEE 802.1p class of service  Port security supported  Port bandwidth control supported  Support IEEE 802.1d Spann ing tree protocol  Supports GVRP function  PortBase VLAN/802.1Q VLAN supported  IEEE 802. ...

  • LevelOne GSW-2493 - page 9

    3 Port Trunk Support IEEE802.3ad with LACP function and provide 7-trunk group of 4 mem ber ports within 26 ports Spanning Tree IEEE802.1d spanning Tree VLAN Port based VLAN IEEE802.1Q Tag VLAN IEEE802.1v Protocol VLAN (IP, IPX,..) Static VLAN groups up to 256, Dynamic VLAN group up to 2048, VLAN ID from 0 to 4094 QOS Policy Supports 8 priority leve ...

  • LevelOne GSW-2493 - page 10

    4 Stacking The switch provide Stack Grouping feature and through master switch interface can manage and stack up to 8 units. 802.1x Support IEEE802.1x User- A uthentication and can report to RADIUS server.  Reject  Accept  Authorize  Disable DHCP DHCP Client Packet filter Broadcast storm Package Contents Unpack the contents of the GSW-2 ...

  • LevelOne GSW-2493 - page 11

    5 R a c k - m o u n t e d K i t P o w e r C o r d U s e r M a n u a l Figure 1-2. Package Contents Compare the contents of your GSW-2493 pa ckage with the standard checklist above. IF any item is missing or damaged, please contact your local dealer for service. Ethernet Switching Technology Ethernet Switching Technology dramatically boosted the to ...

  • LevelOne GSW-2493 - page 12

    6 2. Hardware Description This Section mainly describes the hardw are of the GSW-2493, and gives a physical and functional overview of the switch. P h y s i c a l D i m e n s i o n The GSW-2493 physical dimension is 440mm(W) x 280mm(D) x 44mm(H) . F r o n t P a n e l The Front Panel of the GSW- 2493 consists of 3 module sl ots. One module slot is l ...

  • LevelOne GSW-2493 - page 13

    7 Green The port is connecting with the device. Blinks The port is receiving or transmitting data. LNK/ACT Off No device attached. Orange The port is operati ng in Full-duplex mode. Blinks Collision of Packets occurs in the port. FDX/COL Off In half-duplex mode Table 2-1. The Description of LED Indica tors R e a r P a n e l One module slot, 3-prong ...

  • LevelOne GSW-2493 - page 14

    8 Attaching Rubber Feet A. Make sure mounting surface on the botto m of the Switch is grease and dust free. B. Remove adhesive backing from your Rubber Feet. C. Apply the Rubber Feet to each corner on the bottom of the Switch. These footpads can prevent the Switch from shock/vibration. Rack-mounted Installation The GSW-2493 come with a rack-mounted ...

  • LevelOne GSW-2493 - page 15

    9 3. Network Application GSW-2493 is designed as a segment switch. T hat is, with its large address table (8000 MAC address) and high performance, it is ideal for interconnecting networking segments. PC, workstations, and servers can communica te each other by dire ctly connecting with GSW-2493. The switch automat ically learns nodes addre ss, whic ...

  • LevelOne GSW-2493 - page 16

    10 devices to manage); management applications r epresent the Stack as a single device, and simple point and click management. Stack able technology allows you to increase the resiliency and the versatilit y of your network edge to accommodate evolution for speed and converged applications. Followin g figures are example of stacking workgroup appli ...

  • LevelOne GSW-2493 - page 17

    11 4. Console Management Login in the Console Interface When the connection between Switch and PC is ready, turn on the PC and run a terminal emulation program or Hyper Terminal and configure its communication parameters to match the following default c haracteristics of the console port: Baud Rate: 9600 bps Data Bits: 8 Parity: none Stop Bit: 1 Co ...

  • LevelOne GSW-2493 - page 18

    12 Console login screen M a i n M e n u There are five selections as follow.  Status and Counters: Show the status of the switch.  Switch Static Configuration: Configure the switch.  Protocol Related Configuration: Configure the protocol function.  System Reset Configuration: Restart the system or re set switch to default configuration. ...

  • LevelOne GSW-2493 - page 19

    13 Main menu line interface Control Key description: The control keys provided in all menus: Tab: Move the vernier to next item. Backspace: Move the vernier to previous item. Enter: Select item. Space: Toggle selected item to next configure or change the value. Esc: to exit the current action mode. ...

  • LevelOne GSW-2493 - page 20

    14 Function Description Status and Counters In Status and Counters, you can view Po rt status, counters , and configure system parameter. You can press the “ Tab ” or “ Backspace ” to choose item , and press “ Enter ” key to select item. Status and Counters interface Port Status It displays status of port. Select the <Previous Page&g ...

  • LevelOne GSW-2493 - page 21

    15  Negotiation: display the auto negotiation status.  FC: display the flow control stat us is “enable” or “disable”.  BP: displa y backpr essure status.  Bandwidt h In/Out: display bandwidth In/out control status.  Priority: display th e port priorit y status.  Security: display the port security status. Port status inter ...

  • LevelOne GSW-2493 - page 22

    16 Port counter information interface System Information It displays the system parameter. 1. System Name: the name of device. 2. System Location: where the device is located. 3. System Description: the name of device type. 4. Firmware Version: the switch’s firmware version. 5. Kernel Version: the system kernel software version. 6. Hardware Versi ...

  • LevelOne GSW-2493 - page 23

    17 System Information interface ...

  • LevelOne GSW-2493 - page 24

    18 Switch Static Configuration In Switch Static Configurati on, it has 8 main functions – Administration, Port, Trunk, Port Mirroring, VLAN, Priority, MAC Addr ess, and Misc Configur ation. Under each function, there are more sub-functions. We will descr ibe in following paragraph. Switch Configuration interface Administration Configuration In Ad ...

  • LevelOne GSW-2493 - page 25

    19 Administration Configuration main interface Device Information You can configure the device information. 1. Select <Edit> action to configure. 2. Name: assign the name for the switch. 3. Description: a short description for the switch. 4. Location: the switch location, ex: Taipei. 5. Contact: the contact person or information. 6. Select &l ...

  • LevelOne GSW-2493 - page 26

    20 Device Information interface IP Configuration You can configure the IP for this switch. The system has the default IP address. You can re-configure or use the default value. 1. Select the <Edit> 2. DHCP Client: disable or enable the DHCP client function. 3. IP Address: assign the switch IP address. The default IP is 192.168.16.1. 4. Subnet ...

  • LevelOne GSW-2493 - page 27

    21 IP Configuration interface User Name Configuration You can change the console and w eb management login user name. 1. Select the <Edit> 2. Enter the new user name 3. Select the <Save> User Name Configuration interface ...

  • LevelOne GSW-2493 - page 28

    22 Password Configuration You can change the console and web management login password. 1. Select the <Edit> 2. Old Password: enter the old password. 3. New Password: enter the new password. 4. Enter Again: reenter the new password for confirmation. 5. Select the <Save> Password Configuration interface Port Configuration You can set up ...

  • LevelOne GSW-2493 - page 29

    23 mode). 7. BP: enable or disable Back Pressure function (Backpressure for half duple x mode). 8. Bandwidth In/ Out: per port packet transmission rate control. Per level is 100Kbps. It supports individual control method of TX and RX. 9. Priority: set port to high or low priority. 10. Security: enable or disable port security function. 11. Select t ...

  • LevelOne GSW-2493 - page 30

    24 Trunk Configuration interface Port Mirroring Configuration The port mirroring is a method for monitor tr affic of switched networks. The specific port can monitor traffic through the mirror ports. The monitored ports in or out traffic will be duplicated into monitoring port. 1. Select the <Edit> 2. Mirroring State: select the port-mirrorin ...

  • LevelOne GSW-2493 - page 31

    25 Port Mirroring interface 3. Analysis port: Set the destination port of mirrori ng packet. All of the packets of mirroring port will be duplicated and sent to Analysis port. 4. Port State: use “ Space ” key to mark the port that wanted to be mirrored. 5. Select the <Save> . Port Mirroring interface ...

  • LevelOne GSW-2493 - page 32

    26 VLAN Configuration You can configure VLAN in VL AN Configuration. There ar e four functions in VLAN Configuration mode: VL AN Configuration, Create a VL AN Group, Edit/Delete VLAN Group and Group Sorted Node. Follow the bel ow description to configure VLAN. VLAN Configuration Main interface VLAN Configure Before starting to configure VLAN, you m ...

  • LevelOne GSW-2493 - page 33

    27 ¾ Acceptable Frame type: It matches that Ingress Filtering Rule 2 on web. Drop untagged frame. Press “ Space ” key to select drop or forward the untagged frame. 3. Select <Save> to save the configuration. VLAN Configure interface Create VLAN Group  Create Port-Based VLAN 1. Select <Edit>. 2. VLAN Name: Type a name for the new ...

  • LevelOne GSW-2493 - page 34

    28 Create VLAN Group: PortBase interface  Create 802.1Q VLAN 1. Enable security VLAN setting: select to enable or dis able security VLAN group. When you select to enable security VLAN group, only the memb ers in this VLAN group can access to the switch. The steps of setting security VLAN refer to the following step 2~ 8. After you have confi gur ...

  • LevelOne GSW-2493 - page 35

    29 2. Select <Edit> . 3. VLAN Name: Type a name for the new VLAN, ex: VLAN01. 4. VLAN ID: Type a VID (between 1~4094). The def ault is 1. There are 256 VLAN groups to provided configure. 5. Protocol VLAN: Press “ Space ” key to choose protocols type. 6. Member: Press “ Space ” key to change the member value.  Untagged: this port is ...

  • LevelOne GSW-2493 - page 36

    30 ports from this VLAN group. 4. After edit or delete the VLAN, select <Save> action to save all configures value. NOTE: 1. The VLAN Name and VLAN ID cannot modify. 2. In 802.1Q VLAN mode, the def ault VLAN can’t be deleting. 3. In Port Base VLAN mode, there is no default VLAN. Edit/Delete a VLAN Group interface (802.1Q VLAN group) Group S ...

  • LevelOne GSW-2493 - page 37

    31 Group Sorted Mode interface ...

  • LevelOne GSW-2493 - page 38

    32 Priority Configurati on You can configure port priority level. There ar e 0~7-priority level can map to high or low queue. 1. Select <Edit> . 2. Press “ Space ” key to select the priority le vel mapping to high or low queue. 3. Qos Mode: select the mode to process incoming packets.  First comes first service: the switch will process ...

  • LevelOne GSW-2493 - page 39

    33 Priority Configuration interface MAC Address Configuration When you add a static MAC address, it re mains in the switch's address table, regardless of whether the devic e is physically connected to the switch. This saves the switch from having to re-learn a devic e's MAC address when the disconnected or powered-off device is active on ...

  • LevelOne GSW-2493 - page 40

    34 Static MAC Address  Add the Static MAC Address You can add static MAC address in switch MAC table. 1. Select <Add> Æ <Edit> key to add the static MAC address. 2. MAC Address: Enter the MAC address of the port that should permanently forward traffic, regardless of the device network activity. 3. Port No.: press “ Space ” key t ...

  • LevelOne GSW-2493 - page 41

    35  Delete static MAC address 1. Select <Delete> key. 2. Choose the MAC address that you want to delete and then press “ Enter ”. 3. When pressing “ Enter ” will complete deletion. Filtering MAC Address You can add, delete, and edi t filtering MAC address. Filtering MAC Address interface  Add the Filtering MAC Address 1. Select ...

  • LevelOne GSW-2493 - page 42

    36 Add Filtering MAC Address interface  Edit Filtering MAC address 1. Select <Edit> key to modify a stat ic Filtering address. 2. Choose the MAC address that you want to modify and then press “ Enter ”. 3. Select <Edit> key to modify. 4. Press “ ESC ” to go back action menu line 5. Select <Save> to save all configure va ...

  • LevelOne GSW-2493 - page 43

    37  MAC Address Ageing Time: MAC address table refresh time setting. Type the number of seconds that an inactive MAC ad dress remains in the switch’s address table. The valid range is 0, 300~ 765 seconds. Default is 300 seconds.  Broadcast Storm Filter mode: configure the broadcast st orm filter mode. The valid threshold values are 5%, 10%, ...

  • LevelOne GSW-2493 - page 44

    38 in stacking group. When the stacking group is set up, you can only configure the slave switches through the master switch. Note: 1. Before configuring the stacking function, make sure all stack switches are in the same network. 2. Configure stacking function; you must configure the master switch first. 3. After you have configured the stacking f ...

  • LevelOne GSW-2493 - page 45

    39 Protocol Related Configuration You can configure Spanning Tree Protocol, SNMP, LACP, IGMP/GVRP, and 802.1x in Protocol Relate Conf iguration section. Protocol Relate Configuration interfa ce STP Spanning tree is a link management protocol that provides path redundancy while preventing undesirable l oops in the network. STP Configuration interfac ...

  • LevelOne GSW-2493 - page 46

    40 STP Setup You must enable Spanning Tree functi on before configure STP function. 1. Select <Edit> 2. Use “ Space ” key to select the option. 3. Select <Save> . STP Setup interface System Configuration You can configure the STP system param eter after enable the STP function. You can view spanning tree information ab out the Root ...

  • LevelOne GSW-2493 - page 47

    41 STP System Configuration interface Per Port Setting 1. Select <Edit> . 2. Path Cost: specifies the path cost of the port that switch uses to determine which port are the forwarding ports. 3. Priority: This is mean port priority; you can ma ke it more or less likely to become the root port. 4. Press “ ESC ” goes back action menu line. 5 ...

  • LevelOne GSW-2493 - page 48

    42 Per Port Setting interface SNMP To define management stations as trap managers and to enter SNMP community strings. You can also define a name, loca tion, and contact person for the switch. SNMP Configuration interface ...

  • LevelOne GSW-2493 - page 49

    43 SNMP System Options 1. Press <Edit> . 2. Name: assign a name for the switch. 3. Contact: Type the name of contac t person or organization. 4. Location: Type the location of the switch. 5. Press “ ESC ” goes back action menu line. 6. Press <Save> to save configure value. SNMP System Options interface Community Strings  Add Comm ...

  • LevelOne GSW-2493 - page 50

    44 Add Community Strings interface  Edit Community Name 1. Select <Edit> 2. Choose the item that you w ant to modify and then press “ Enter ” . 3. Community Name: type the new name. 4. Write Access: Press “ Space ” key to change the right. 5. Select <Save> . Edit Community Strings interface ...

  • LevelOne GSW-2493 - page 51

    45  Delete Community Name 1. Select <Delete> . 2. Choose the community name that y ou want to delete and then press “ Enter ”. 3. When pressing “ Enter ” will complete deletion. Trap Managers A trap manager is a management station that receives traps, the system alerts generated by the switch. If no tr ap manager is defined, no tr ...

  • LevelOne GSW-2493 - page 52

    46 Add Trap Manager interfac e  Delete Trap Manager 1. Select <Delete> 2. Choose the trap manager that you want to delete and then press “ Enter ”. 3. When pressing “ Enter ” will complete deletion. LACP The Link Aggregation Contro l Protocol (LACP) provi des a standardized means for exchanging information between Partner Systems o ...

  • LevelOne GSW-2493 - page 53

    47 LACP Configuration interface Working Ports Setting 1. Select <Edit> 2. Group: Display the trunk group ID. 3. LACP: Press “ Space ” key to enable or disable LA CP (Link Aggregation Control Protocol) support. When LACP enable, the group is LACP static trunk group. When LACP disable, the group is local static trunk group. 4. Working Port ...

  • LevelOne GSW-2493 - page 54

    48 LACP Working Ports configuration interfa ce LACP State Activity 1. Select <Edit> 2. Use “ Space ” key to select the Port State Activity.  Active: The port automatically sends LACP protocol packets.  Passive: The port does not automatically send LACP protocol packets, and responds only if it receives LACP pr otocol packets from th ...

  • LevelOne GSW-2493 - page 55

    49 Group Status When you setting trunk group, you can s ee the relation information in here. LACP Group State interface IGMP/GVRP You can enable or disable the IG MP/GVRP (GARP VLAN Registration Protocol). 1. Select <Edit> 2. Use “ Space ” key to change the value 3. Select <Save> ...

  • LevelOne GSW-2493 - page 56

    50 IGMP/GVRP Configuration interface 802.1x 802.1x Configuration interface 802.1x Setup 1. Select <Edit> 2. Use “ Space ” key to Enable or Disable the 802.1x. ...

  • LevelOne GSW-2493 - page 57

    51 3. Select <Save> 802.1x Setup interface System Configuration After enabling the IEEE 802.1X function, you can configure the parameters of this function. 1. Select <Edit> 2. Radius Server IP: set the Radius Server IP address. 3. Shared Key: set an encryption key for using during authentication sessions with the specified radius server ...

  • LevelOne GSW-2493 - page 58

    52 802.1x System Configuration interface Per Port Configuration You can configure 802.1x aut hentication state for each port. The State provides Disable, Accept, Reject and Authorize. Use “ Space ” key change the state value. 802.1x Per Port Setting interface ...

  • LevelOne GSW-2493 - page 59

    53 Misc Configuration 1. Select <Edit> 2. Quiet period: set the period during which th e port doesn’t try to acquire a supplicant. 3. TX period: set the period the port wait fo r retransmit next EAPOL PDU during an authentication session. 4. Supplicant timeout: set the period of time the switch wait for a supplicant response to an EAP reque ...

  • LevelOne GSW-2493 - page 60

    54 System Reset Configuration System Reset Configuration interface Factory Default Reset switch to default configuration. Press “ Y ”, switch will load default setting. After finished load default setting, switch will reboot automatically. Factory Default interface ...

  • LevelOne GSW-2493 - page 61

    55 System Reboot Reboot the switch in software reset. TFTP Configuration It provides user to update firmware or restore EEPROM value or upload current EEPROM value. TFTP Update Firmware interface Update Firmware It provides user uses TFTP to update firmware. 1. Start the TFTP server, and copy firmware update version image file to TFTP server. 2. Se ...

  • LevelOne GSW-2493 - page 62

    56 Update Firmware interface TFTP Restore Configuration You can restore EEPROM value, which sa ved in TFTP server, from TFTP server. 1. Start the TFTP server. 2. Select <Edit> . 3. TFTP Server IP: type the IP of TFTP server. 4. Restore File Name: type the image file name. 5. Press “ ESC ” back to action menu line. 6. Select <Save> , ...

  • LevelOne GSW-2493 - page 63

    57 TFTP Restore Configuration interface TFTP Backup Configuration You can save current EEPROM value to TFTP server as backup. The backup file can be restore from TFTP server when you need. 1. Start the TFTP server. 2. Select <Edit> . 3. TFTP Server IP: type the IP of TFTP server. 4. Backup File Name: type the image file name. 5. Press “ ESC ...

  • LevelOne GSW-2493 - page 64

    58 TFTP Backup Configuration interface X-modem Upgrade Before using X-modem upgrade, disconnect terminal and modify baud rate to 57600bps, then connect again. 1. Press “ X ” key to start upgrading from X-modem. 2. You will see the following screen displays. 3. Select “ send file " under Transfer menu from menu bar. 4. Select " brows ...

  • LevelOne GSW-2493 - page 65

    59 6. After successfully upgraded the new fi rmware, please modify baud rate to 9600bps. ...

  • LevelOne GSW-2493 - page 66

    60 5. Web-Based Management This section introduces the configur ation and functions of the Web-Based management. If your OS is Windows XP with Service Pack 2, please disable the windows firewall before connecting to UI. About Web-based Management Inside the CPU board of the switch exis ts an embedded HTML web site residing in flash memory. It offer ...

  • LevelOne GSW-2493 - page 67

    61 Password: root Online Help You can click Hel p button when you have any configuration question during the configuring. System Login 1. Launch the Internet Explorer. 2. Type http:// and the IP addr ess of the switch. Press “ Enter ”. 3. The login screen appears. 4. Key in the user name and password. The default user name and password is “ r ...

  • LevelOne GSW-2493 - page 68

    62 GSW-2493 Port status In Port status, you can view every port status that depended on user setting and the negotiation result. 1. Port: display the number of port. The first integer is the module slot number. The second integer is the port num ber in the module. For exam ple: Port 1-1, it means the first port on the first module slot. 2. Type: di ...

  • LevelOne GSW-2493 - page 69

    63 8. Back Pressure: Display the Back Pressure status setting. “Config” means the value that user configured. “Actual” means the current value of the port. 9. Bandwidth In/ Out: display the port incoming and outgoing bandwidth. 10. Priority: display the port static priority status is “High” or “Low” or “Disable”. 11. Port Securi ...

  • LevelOne GSW-2493 - page 70

    64 Port information interface Port Statistics The following information provides a view of the current port statistic information. Click Cl ea r button to clean all counts. ...

  • LevelOne GSW-2493 - page 71

    65 Port Statistics Administrator In Administrator function, it provides the following functions: IP Configuration, Switch Settings, C onsole Port Information, Port Controls, Trunking, Forwarding and Filtering, VL AN Configuration, Spanning Tree, Port Mirroring, SNMP Management, Security Manager, and 802.1x Configuration. Administrator interface IP ...

  • LevelOne GSW-2493 - page 72

    66 IP configuration interface Switch Setting In Switch setting, it has three parts of se tting – Basic, Advance, and Misc Config. We will describe the configur e detail in following. Basic Switch Settings In Basic Switch Setting, it disp lays the switch basic information.  System Name: the name of switch.  System Location: the switch physic ...

  • LevelOne GSW-2493 - page 73

    67 Switch basic sett ing interface Advanced Setting In Advanced setting, it has two sections – MAC Table Address Entry and Priority Queue Service. After the configuration, click Ap p ly button to complete the configuration.  Enable MAC address Aging Out: to enable the MAC address age out function. When it is disabling, the following configure ...

  • LevelOne GSW-2493 - page 74

    68 port's total bandwidth used by broadcast traffic. When broadcast traffic for a port rises above the threshold you se t, broadcast storm control becomes active. The valid threshold value are 5%, 10%, 15%, 20%, 25% and off. Switch Advanced setting interface  802.1p Priority: select the priority queue service type.  First Come First Serv ...

  • LevelOne GSW-2493 - page 75

    69 Misc Config  Collisions Retry Forever: disable is in half duplex. If happen collision will retry 48 times and then drop frame. Enable is in half duplex. If happen collision will retry forever.  Hash Algorithm: CRC Hash or Direct Map for MAC address learning algorithm  IFG Compensation: Internal Packet Gap time com pensation configure. S ...

  • LevelOne GSW-2493 - page 76

    70 within a network: 1. Auto mode needs to be enabled when the router’s IP address is smaller than other switches in the subnet. 2. IGMP needs to be enabled when the router’s IP address is not smaller than other switches in the subnet. This Router supports IGMP protocol, but IGMP has to be enabled, and the Router has to be the Querier. ...

  • LevelOne GSW-2493 - page 77

    71 3. The following topology must be set when the IP address of the switch is not the smallest in the subnet. The network will cause a multi-cast storm from the IGMP client report if it is in Auto mode. All switches must be in disable mode when the VOD server is configured for IGMP Querier. Note: It is suggested that the VOD server switch have the ...

  • LevelOne GSW-2493 - page 78

    72 Console Port Information Console is a standard UART interface to communicate with Serial Port. User can use windows HyperTerminal program to link the switch. Please refer to Console Management Æ Console login for detail steps. Console port information shows as follow: Bits per seconds: 9600 Data bits: 8 Parity: none Stop Bits: 1 Flow control: n ...

  • LevelOne GSW-2493 - page 79

    73 Pressure to confine the ingress rate to meet the specified rate.  In: fill in the port effective ingress rate. The valid range is 0 ~ 1000. The unit is 100K. 0: disable rate control. 1 ~ 1000: valid rate value.  Out: fill in the port effective egress rate. The valid range is 0~1000. The unit is 100K. 0: disable rate control. 1 ~ 1000: vali ...

  • LevelOne GSW-2493 - page 80

    74 Group, and enable its transmission and reception functions in an orderly manner. Link aggregation lets you group up to eight c onsecutive ports into a single dedicated connection. This feature can expand bandw idth to a device on the network. LACP operation requires full-duplex mode, more detail information refers to IEEE 802.3ad. Aggregator set ...

  • LevelOne GSW-2493 - page 81

    75 Trunking— Aggregator Setting interf ace Aggregator Information When you had setup the LACP aggregator, you will see relation information in here. Trunking – Aggregator Information interface ...

  • LevelOne GSW-2493 - page 82

    76 Aggregator Information State Acti vity When you had setup the LACP aggregator, you can configur e port state activity. You can mark or un-mark the port. When you mark the port and click App ly button the port state activity will change to Active . Opposite is Passive . 1. Active: The port automatically sends LACP protocol packets. 2. Passive: Th ...

  • LevelOne GSW-2493 - page 83

    77 Forwarding and Filtering IGMP Snooping The switch support IP multicast, you can enable IGMP protocol on web management’s switch setting advanced page, then display the IGMP snooping information in this page, you can view difference multicast group VI D and member port in here, IP multicast addresses range from 224.0. 0.0 through 239.255.255.25 ...

  • LevelOne GSW-2493 - page 84

    78 IGMP Snooping interface Static MAC Address When you add a static MAC address, it re mains in the switch's address table, regardless of whether the devic e is physically connected to the switch. This saves the switch from having to re-learn a devic e's MAC address when the disconnected or powered-off device is active on the network agai ...

  • LevelOne GSW-2493 - page 85

    79 Static MAC Address interface MAC filtering MAC address filtering allows the switch to drop unwanted tr affic. Traffic is filtered based on the destination addresses. 1. In MAC Address box, enter the MAC addres s that wants to filter. 2. VLAN ID: If tag-based (802.1Q) VLAN are set up on the switch, in the VLAN ID box, type the VID to associate wi ...

  • LevelOne GSW-2493 - page 86

    80 MAC Filtering interface VLAN configuration A Virtual LAN (VLAN) is a logical network grouping that limits the broadcast domain. It allows you to isolate network traffic so onl y members of the VLAN receive traffic from the same VLAN members. Ba sically, creating a VLAN fr om a switch is logically equivalent of reconnecting a group of netwo rk de ...

  • LevelOne GSW-2493 - page 87

    81 VLAN Configuration interface Port-based VLAN Packets can go among only mem bers of the same VLAN group. Note all unselected ports are treated as belonging to another single VLAN. If t he port-based VLAN enabled, the VLAN-tagging is ignored. If an end station sends packets to different VL ANs, it has to be either capable of tagging packets it sen ...

  • LevelOne GSW-2493 - page 88

    82 VLAN – PortBase interface 1. Click Ad d >> to create a new VLAN group. 2. Enter the VLAN name, group ID and select the members of VLAN group. 3. Click Ap p ly . ...

  • LevelOne GSW-2493 - page 89

    83 Add PortBase VLAN interface 4. You will see the VLAN displays. PortBase VLAN group list interface ...

  • LevelOne GSW-2493 - page 90

    84 5. If the groups’ list is over one page, you can click Nex t P a ge to view other VLAN groups. 6. Use Del et e button to delete unwanted VLAN. 7. Use Ed i t button to modify ex isting VLAN group. 802.1Q VLAN Tagged-based VLAN is an IEEE 802.1Q specif ication standard. T herefore, it is possible to create a VLAN across devices fr om different s ...

  • LevelOne GSW-2493 - page 91

    85 802.1q VLAN interface  Basic 1. Click A dd button. 2. Enable GVRP Protocol: check the check box to enable GVRP protocol. 3. Group Name: assign a name for the new VLAN. 4. VLAN ID: fill in a VLAN ID (between 2-4094). The default is 1. 5. Protocol VLAN: choose the protocol type. Default is NONE. 6. From the Availa ble ports box, select ports to ...

  • LevelOne GSW-2493 - page 92

    86 Add 802.1q VLAN interface -1 7. Click Ne x t . Then you will see the page as follow. Add 802.1q VLAN interface -1 8. To set the outgoing frames are VLAN -Tagged frames or untagged. Then click ...

  • LevelOne GSW-2493 - page 93

    87 Ap p ly .  Tag: outgoing fram es with VLAN-Tagged.  Untag: outgoing frames without VLAN-Tagged.  Port VID: Configure port VID settings 1. Port VLAN ID: enter the port VLAN ID. 2. Ingress Filtering: Ingress filtering lets frames bel onging to a specific VLAN to be forwarded if the port belongs to that VLAN.  Enable : Forward only pack ...

  • LevelOne GSW-2493 - page 94

    88 802.1q VLAN – Port VLAN ID interface Spanning Tree The Spanning-Tree Protocol (STP) is a standardized method (IEEE 802.1d) for avoiding loops in switched networks. When STP enabled, to ensure that only one path at a time is active between any two nodes on the network. We are recommended that you enable STP on all switches ensures a single acti ...

  • LevelOne GSW-2493 - page 95

    89 Spanning Tree – System Configuration interface System Confi gurati on 1. You can view spanning tree info rmation about the Root Bridge. 2. You can view spanning tr ee status about the switch. 3. You can modify STP state. After modification, click Ap p l y button.  Priority: assign path priority number.  Max Age: the maximum path age  ...

  • LevelOne GSW-2493 - page 96

    90 3. Assign the port priority va lue. The value range is from 0 to 255. The lowest value has higher priority. 4. Click App ly button. SPT – Per Port Configuration interface Port Mirroring The Port mirroring is a method for monitor tr affic in switched netwo rks. Traffic through ports can be monitored by one s pecific port. That is, traffi c goes ...

  • LevelOne GSW-2493 - page 97

    91 2. Analysis Port: It’s mean mirror port can be used to see all monitor port traffic. You can connect mirror port to LAN analyzer or Netxray. 3. Monitor Port: the ports you want to monitor. A ll monitor port traffic will be copied to mirror port. You can select max 25 monitor ports in the switch. User can choose which port want to monito r in o ...

  • LevelOne GSW-2493 - page 98

    92 You can define management stations as tr ap managers and to enter SNMP community strings. You also can define a name, location, and contact person for the switch. Fill in the system options data, and then click Apply to update the changes.  System Options 1. Name: enter a name for the switch. 2. Location: enter the switch physical location. 3 ...

  • LevelOne GSW-2493 - page 99

    93 MIB-object information. 3. RW: Read write. Enables requests accompanied by this string to display MIB-object information and to set MIB objects. 4. Click A dd .  Trap Manager A trap manager is a management station that receives traps, the system alerts generated by the switch. If no tr ap manager is defined, no tr aps will issue. Create a tra ...

  • LevelOne GSW-2493 - page 100

    94 802.1X When enabling the IEEE 802.1X function, y ou can configure the parameters of this function. System Confi gurati on 1. Radius Server IP: set the Radius Server IP address. 2. Server Port: set the UDP destination port for authentication requests to the specified Radius Server. 3. Accounting Port: set the UDP destination port for accounting r ...

  • LevelOne GSW-2493 - page 101

    95  Accept: the specified port is required to be held in the Authorized state.  Authorized: the specified port is set to th e Authorized or Unauthorized state in accordance with the outcome of an authentication exchange between the Supplicant and the aut hentication server.  Disable: The specified port is required to be held in the Authori ...

  • LevelOne GSW-2493 - page 102

    96 Misc Configuration 1. Quiet period: Set the period during which the port doesn’t try to acquire a supplicant. 2. TX period: Set the period the port waits to re transmit next EAPOL PDU during an authentication session. 3. Supplicant timeout: Set the period of time the s witch waits for a supplicant response to an EAP request. 4. Server timeout: ...

  • LevelOne GSW-2493 - page 103

    97 1. TFTP Server IP Address: fill in your TFTP server IP. 2. Firmware File Name: the name of firmware image. 3. Click App ly . TFTP Update Firmware interface Configuration Backup In Configuration Backup, you can restore the backup c onfiguration into the switch. Also, you can backup the configuration to TFTP server . TFTP Restore Configuration You ...

  • LevelOne GSW-2493 - page 104

    98 TFTP Restore Configuration interface TFTP Backup Configuration You can save current EEPROM va lue from the switch to TFTP server, then go to the TFTP restore configuration page to restore the EEPROM value. 1. TFTP Server IP Address: fill in the TFTP server IP 2. Backup File Name: fill the file name 3. Click App ly . TFTP Backup Configuration int ...

  • LevelOne GSW-2493 - page 105

    99  Subnet mask: 255.255.255.0  The other setting value is back to disable or none. Click De faul t button to reset switch to default setting. Factory Default interface System Reboot Reboot the Switch in software reset. Click Ap p ly button to reboot the switch. System Reboot interface Panel List Display the switch panel GUI. When the switch ...

  • LevelOne GSW-2493 - page 106

    100 IP Stacking This function allows switch to stack up to 8 stackable switches as a unit group. When configuring the stacking functi on, beware the following points.  Any port on the switch can be used to stack.  Before configuring the stacking function, make sure all stack switches are in the same network.  When configure stacking functi ...

  • LevelOne GSW-2493 - page 107

    101 IP Stacking interface 4. Click A ppl y button to apply the configurati on. When the master switch has configured, you will see the following screen. IP Stacking master switch configure finishe d interface 5. After you have configured the stacking function, use Cat. 5 cable to connect each switch in the stacking group. And wait fo r few minutes ...

  • LevelOne GSW-2493 - page 108

    102 communicate and collect the dat a from the slave switches. 6. Connect to the master switch through the Web. You will se e the following screen display. 7. Click any function in the menu bar of the ma ster switch to conf igure the switch in the stacking group. You will see the IP of stacking group lis t that display the IP and the switch name. I ...

  • LevelOne GSW-2493 - page 109

    103 Stacking group configuration interface ...

  • LevelOne GSW-2493 - page 110

    104 6. Troubleshooting This section is intended to help you solve the most common problems on the GSW-2493. Incorrect connections The switch port can auto detect straight or crossover cabl e when you link switch with other Ethernet device. For t he RJ-45 connector should use correct UTP or STP cable, 10/100Mbps port use 2 pairs t wisted cable and G ...

  • LevelOne GSW-2493 - page 111

    105 at any time. Data path loops will cause broadc ast storms that will severely impact your network performance. Diagnosing LED Indicators The Switch can be easily moni tored through panel indicators to assist in identifying problems, which describes common problems you may encounter and where you can find possible solutions. IF the power indicato ...

  • LevelOne GSW-2493 - page 112

    106 7. Technical Specification This section provides the s pecifications of the GSW-2493, and the following table lists these specifications. Standard IEEE802.3 10BASE-T IEEE802.3u 100BASE-TX/100BASE-FX IEEE802.3z Gigabit SX/LX IEE802.3ab Gigabit 1000T IEEE802.3x Flow Control and Back pressure IEEE802.3ad Port trunk with LACP IEEE802.1d Spanning tr ...

  • LevelOne GSW-2493 - page 113

    107 Connector 8-port 10/100TX module: RJ-45 8-port 100FX(Multi /Single Mode) module: SC 2-port Gigabit SX/LX module: SC 2-port Gigabit 1000T module: RJ-45 Expansion module  8 port 10/100TX module with RJ-45 connector (MDU-2493TX)  8 port 100Mbps multi m ode fiber module with SC connector (MDU-2493SXSC)  2 Gigabit copper module with RJ-45 c ...

  • LevelOne GSW-2493 - page 114

    108 Storage temperature -40 ℃ ~70 ℃ , 95% RH EMI FCC Class A, CE Safety UL, cUL, CE/EN60950 ...

Manufacturer LevelOne Category Switch

Documents that we receive from a manufacturer of a LevelOne GSW-2493 can be divided into several groups. They are, among others:
- LevelOne technical drawings
- GSW-2493 manuals
- LevelOne product data sheets
- information booklets
- or energy labels LevelOne GSW-2493
All of them are important, but the most important information from the point of view of use of the device are in the user manual LevelOne GSW-2493.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals LevelOne GSW-2493, service manual, brief instructions and user manuals LevelOne GSW-2493. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product LevelOne GSW-2493.

Similar manuals

A complete manual for the device LevelOne GSW-2493, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use LevelOne GSW-2493 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of LevelOne GSW-2493.

A complete LevelOne manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual LevelOne GSW-2493 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the LevelOne GSW-2493, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the LevelOne GSW-2493, that we can find in the current document
3. Tips how to use the basic functions of the device LevelOne GSW-2493 - which should help us in our first steps of using LevelOne GSW-2493
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with LevelOne GSW-2493
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of LevelOne GSW-2493 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning LevelOne GSW-2493?

Use the form below

If you did not solve your problem by using a manual LevelOne GSW-2493, ask a question using the form below. If a user had a similar problem with LevelOne GSW-2493 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)