-
Makita 6073D and 6073DW - page 1
Cordless Driver Drill Capacities Steel Wood Wood screw Machine screw 10mm 15” 51mmx35mm 6mm (318”) (19132”) (13164’’ x 1 318”) (15164”) Equipped with Electric Brake 10 mm (3/8”) MODEL 60731) 10 mm (3/8”) MODEL 6073DW With Fast Charger Dimensions (L x W x H) 255 mm x 58 mm x 223 mm (10” x 2 114” x 8 25132”) No load speed IRPM ...
-
Makita 6073D and 6073DW - page 2
IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFE- REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PER- TY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO SONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. 2. 3. 4. 5. 6. 7. 8. 9. IO. 11. 12. 13. 2 KEEP WORK AREA CLEAN. Cluttered areas and benches invit ...
-
Makita 6073D and 6073DW - page 3
14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don‘t carry plugged-in tool with finger on switch. Be sure switch is OFF when plugging in. 16. OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only extens ...
-
Makita 6073D and 6073DW - page 4
I. SAVE THESE INSTRUCTIONS - This manual Length of Cord (Feet) AWG Size of Cord contains important safety and operating instructions for battery charger. 2. Before using battery charger, read all instructions and cautionary markings on (1) battery charger, (2) battery, and (3) product using battery. 3. CAUTION - To reduce risk of injury, charge onl ...
-
Makita 6073D and 6073DW - page 5
ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge when temperature is BELOW 10°C (5OoF) or ABOVE 4OoC (104OF). 2. Do not attempt to use a step-up transformer, an engine generator or DC power 3. Do not allow anything to cover or clog the charger vents. 4. Always cover the battery terminals with the batte ...
-
Makita 6073D and 6073DW - page 6
Installing or removing battery cartridge 0 Always switch off the tool before insertion or removal of the battery cartridge. 0 To remove the battery cartridge, pull out the set plate on the tool and grasp both sides of the cartridge while withdrawing it from the barrel. 0 To insert the battery cartridge, align the tongue on the battery cartridge wit ...
-
Makita 6073D and 6073DW - page 7
Installing or removing drill bit or driver bit CAUTION : Always be sure that the tool is switched off and the battery cartridge is removed before installing or removing the bit. To install the bit, place it in the chuck as far as it will go. Tighten the chuck by hand. Place the chuck key in each of the three holes and tighten clockwise. Be sure to ...
-
Makita 6073D and 6073DW - page 8
CAUTION : Before inserting the battery cartridge into the tool, always check to see that the trigger switch actuates properly and returns to the "OFF" position when released. Reversing switch action This tool has a reversing switch to change the direction of rotation. Slide the revers- ing switch to the right for clockwise rota- tion or t ...
-
Makita 6073D and 6073DW - page 9
Adjusting fastening torque The fastening torque can be adjusted in six stages by turning the adjusting ring so that the pointer on the adjusting ring points to a number on the tool body. The fastening torque is minimum when the pointer points to the number 1 and maximum when it points to the -8- marking. The clutch will slip at varying torque level ...
-
Makita 6073D and 6073DW - page 10
NOTE : 0 Use the proper bit for the head of the screw that you wish to use. 0 Make sure that the driver bit is inserted straight in the screw head, or the screw and/or bit may be damaged. When driving wood screws, predrill pilot holes to make driving easier and to pre- vent splitting of the workpiece. See the chart. 2.5 - 2.8 (3/32" - 7/64&quo ...
-
Makita 6073D and 6073DW - page 11
Overload protector The overload protector automatically cuts out to break the circuit whenever heavy work is prolonged. Wait 20-30 seconds before resuming operation. 11 ...
-
Makita 6073D and 6073DW - page 12
MA1 NTENANCE CAUTION : Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance. To maintain product SAFETY and RELIABILITY, repairs, maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. 12 ...
-
Makita 6073D and 6073DW - page 13
ACCESSORI ES CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. Ph i I I ips SI o t ted Square drill bit 0 Bi ...
-
Makita 6073D and 6073DW - page 14
May-14-'87 EN 10 mm (3/8") CORDLESS DRIVER DRILL Model 6073D Note: The switch and other part configurations may differ from country to country. 14 ...
-
Makita 6073D and 6073DW - page 15
May 14-'87 EN MODEL 6073D 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 ,&, DESCRIPTION ""0" DESCRIPTION 1 1 1 1 4 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 Pan Head Screw M4x22 iWifh Washer1 Pan Head Screw M4x35 IWith Washer1 Housing Set IWith Item 441 Guide Plat ...
-
Makita 6073D and 6073DW - page 16
P ,+- I MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, return the COMPLETE tool ...
Do you have a question concerning Makita 6073D and 6073DW?
Use the form below
If you did not solve your problem by using a manual Makita 6073D and 6073DW, ask a question using the form below. If a user had a similar problem with Makita 6073D and 6073DW it is likely that he will want to share the way to solve it.