English dropdown-ico

Manual Troy-Bilt 13101 - GTX 16

28 pages 0.51 mb
Download

Go to site of 28

Summary
  • Troy-Bilt 13101 - GTX 16 - page 1

    Models 13074 – GTX 18 (18 HP) 13076 – GTX 20 (20 HP) 13101 – GTX 16 (16 HP) Form 770-1177A (2/98) Owner/Operator Manual GTX Garden T ractor • Safety • Operation • Maintenance ...

  • Troy-Bilt 13101 - GTX 16 - page 2

    2 Thank you for purchasing this product. We feel you now own one of the finest pieces of outdoor power equipment available. All information in this manual is based on the latest product information available at the time of printing. This manual is considered a permanent part of the unit and must stay with the unit if resold. This is a safety, opera ...

  • Troy-Bilt 13101 - GTX 16 - page 3

    W ARNING: Engine exhaust from this product contains chemicals known to the State of California to cause cancer , birth defects or other reproductive harm. Identification Numbers For prompt service, always provide the identification numbers of the unit. The unit’s identification numbers are located on a decal, beneath the seat, on the rear fender. ...

  • Troy-Bilt 13101 - GTX 16 - page 4

    Introduction 1. Unit is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury or death. 2. Serious accidents which may cause injury or property damage can occur if the following safety guidelines are not followed. Operator is solely responsible for accidents or ...

  • Troy-Bilt 13101 - GTX 16 - page 5

    5 Before Operation 1. Before each use, clear work area of objects such as rocks, toys, wire, etc., which could be picked up and thrown by mower blades. 2. Keep unit in safe operating condition. Check the following each time before starting unit: a. All hardware for tightness (especially blade mounting hardware—check for proper torque specificatio ...

  • Troy-Bilt 13101 - GTX 16 - page 6

    Safety (continued) 6 without either the entire grass catcher or the guard in place. 7. If you strike a foreign object, disengage attachment/PTO drive, shut off engine, wait for all moving parts to come to a stop. Remove ignition key. Inspect for and repair any damage before operating equipment again. 8. Never carry passengers. Passengers interfere ...

  • Troy-Bilt 13101 - GTX 16 - page 7

    7 8. If unit is unable to continue moving uphill, disengage attachment drive (PTO), check area on ground immediately behind unit, watch area to rear and proceed backward slowly. 9. Do not operate unit on steep slopes where there is a risk of an overturn. Do not mow slopes with an incline of more than 10 °. Use the Slope Gauge, included with your u ...

  • Troy-Bilt 13101 - GTX 16 - page 8

    8 14. Check brake operation frequently. Adjust and service as necessary as indicated in Section 7 “Maintenance.” 15. Chock wheels (place blocks of wood in front and behind wheels) when performing maintenance with the parking brake off. Securely support unit if it must be raised for any reason. 16. Check wheel attachment hardware regularly and e ...

  • Troy-Bilt 13101 - GTX 16 - page 9

    9 1767130 Instruction/Safety Decal Safety (continued) 4. If electrolyte contacts skin or eyes: a. Flush affected area with water. b. Apply baking soda to neutralize acid. c. Flush eyes with water for 10-15 minutes. d. Call a physician immediately. 5. If electrolyte is swallowed: a. Drink large amounts of water or milk. b. Follow by drinking milk of ...

  • Troy-Bilt 13101 - GTX 16 - page 10

    10 Section 2 Attachments, Kits & Specifications Specifications Engine ....................................*16 HP Briggs and Stratton (GTX 16) *18 HP Kohler (GTX 18) *20 HP Kohler (GTX 20) Governor Speed ................................................. 3600 +/- 75 RPM Start ....................................................................... ...

  • Troy-Bilt 13101 - GTX 16 - page 11

    Attachment, Kits and Specifications (continued) 11 Number Description Below is a list of attachments and kits available for this tractor. The information below is the most current, available at the time this manual was printed. Check with your nearest authorized dealer for current information. 14025 42" Side Discharge Mower 14026 48" Side ...

  • Troy-Bilt 13101 - GTX 16 - page 12

    12 Auxilliary Hydraulic Lever (Model 13076 Only) (F) Brake/Neutral Pedal (B) Choke Lever (C) Attachment Lift Lever (G) Cruise Control Switch (Models 13074 & 13076) (D) Light Switch (E) Hour Meter (H) Fuel Gauge (Models 13074 & 13076) (J) PTO/Attachment Drive Switch (K) Throttle (L) Travel Pedal (M) Ignition/Starter Switch (N) O P Q R S Park ...

  • Troy-Bilt 13101 - GTX 16 - page 13

    Controls (continued) 13 A. Parking Brake Lever Locks brake. Set parking brake when unit is not in use. See page 19 for operating instructions. B. Brake / Neutral Pedal Stops forward or reverse movement of the tractor. See page 19. C. Choke Lever When activated, the choke restricts amount of air mixing with fuel. Activate choke when starting a cold ...

  • Troy-Bilt 13101 - GTX 16 - page 14

    14 Before starting the engine, perform the following steps: 1. Check Engine Oil Level Refer to your specific model in Figure 5-1. Remove dipstick (A, Fig. 5-1). Wipe oil from dipstick with a clean cloth. Insert dipstick back into place. Remove dipstick and check oil level. Keep level between the (“F” Full) and (“L” Add) marks on the dipstic ...

  • Troy-Bilt 13101 - GTX 16 - page 15

    Before Operation (continued) 15 Loosen adjustment knobs (ZZ), slide seat forward or backward. ZZ Fig. 5-3 4. V isually Check Check for and repair loose or missing screws, nuts, and damaged parts. 5. Check Battery To connect the battery initially, remove the red (+) terminal cover from the (+) positive terminal and connect the red battery cable to t ...

  • Troy-Bilt 13101 - GTX 16 - page 16

    Section 6 Operation 16 5. When engine starts, move choke lever (G) down halfway (to half choke). Gradually, move choke lever down (to choke off) as the engine warms up. NOTE: DO NOT RUN ENGINE WITH CHOKE ON FOR PROLONGED PERIODS. ENGINE WILL RUN POORLY (OVER-RICH FUEL MIXTURE) IF OVER-CHOKED. 6. Move throttle (J) up to (fast). Run the engine at ful ...

  • Troy-Bilt 13101 - GTX 16 - page 17

    Operation (continued) 17 Interlock System Leaving the seat while the attachment/PTO drive switch (X, Fig. 6-1) is on or while the brake is off will stop the engine. DO NOT OPERA TE THE UNIT IF THE INTERLOCK SYSTEM DOES NOT FUNCTION PROPERL Y . Interlock System Test Procedure: With the engine running, stop tractor on a level surface (do NOT engage b ...

  • Troy-Bilt 13101 - GTX 16 - page 18

    18 Operation (continued) Auxilliary Hydraulic Lever (Model 13076 Only) (L) Brake/Neutral Pedal (F) Attachment Lift Lever (K) Cruise Control Switch (Models 13074 & 13076) (O) Attachment/PTO Drive Switch (X) Throttle (J) Travel Pedal (M) Parking Brake Lever (N) Ignition/Starter Switch (H) Choke Lever (G) Light Switch (E) Fig. 6-3 P Two-Speed Tran ...

  • Troy-Bilt 13101 - GTX 16 - page 19

    19 Lock Parking Brake Unlock Parking Brake Parking Brake Lever N F Engage pedal (F) before pulling lever (N). Fig. 6-5 Operation (continued) Moving T ractor Manually DO NOT TOW OR PUSH THIS TRACTOR WITH ANOTHER VEHICLE OR RISK DAMAGING THE DRIVE SYSTEM. When pushing the tractor, push it slowly to prevent a temporary lock-up of rear wheels. 2-Speed ...

  • Troy-Bilt 13101 - GTX 16 - page 20

    Section 7 Lubrication and Maintenance 20 BEFORE PERFORMING ANY MAINTENANCE OR ADJUSTMENTS TO THE TRACTOR, ENGINE OR A TT ACHMENTS: DISENGAGE THE A TT ACHMENT/PTO DRIVE, SHUT OFF THE ENGINE AND WAIT FOR ALL MOVING P AR TS TO STOP . SET THE P ARKING BRAKE AND ALLOW THE ENGINE AND MUFFLER TO COOL. Preventive maintenance encourages a longer operating l ...

  • Troy-Bilt 13101 - GTX 16 - page 21

    Maintenance (continued) 21 4. Close oil drain valve (L). Place cap on oil drain tube. Install side panel. Engine Air Intake Screen STOP ENGINE BEFORE CLEANING AIR SCREEN! Check engine air intake screen (C, Fig. 7-1) for debris and clean regularly. A dirty air screen and engine can reduce airflow and cause the engine to overheat. See the engine manu ...

  • Troy-Bilt 13101 - GTX 16 - page 22

    22 2. Adjust screws (N, Fig. 7-5). These screws apply pressure to the front axle. Axle should pivot with a small amount of drag. Fr ont Wheel Alignment Straighten front wheels. Loosen locknuts (Q, Fig. 7-5). Adjust tie rod (Z) so measurement (O) is 1/8" longer than measurement (P). Power Steering Power steering is controlled by the hydraulic s ...

  • Troy-Bilt 13101 - GTX 16 - page 23

    Maintenance (continued) 23 Pr oper Jack Placement A floor jack (not a bottle jack) or an overhead hoist may be used to lift the front of the tractor. Do not attempt to use any other device to lift the tractor. USE EXTREME CARE WHEN JACKING OR HOISTING TRACTOR. BLOCK WHEELS AND USE JACKST ANDS TO SECUREL Y HOLD UNIT IN PLACE. WARNING Fig. 7-7 Do not ...

  • Troy-Bilt 13101 - GTX 16 - page 24

    Maintenance (continued) 24 C A D G H E F L J Fig. 7-9 Transmission Oil Filter: Replace filter after first five hours and every 100 hours thereafter. Filter is located under the tractor, in front of the transmission. Hydrostatic Neutral Adjustment Hydrostatic neutral is set at the factory. If tractor creeps forward or backward while hydrostatic peda ...

  • Troy-Bilt 13101 - GTX 16 - page 25

    Maintenance (continued) 25 Lubrication Chart Engine Crankcase First 5 hours Hydrostatic Transmission Front Wheel Spindles Front Axle Pivot See engine manual Lubrication intervals vary with operating conditions and type of oil used 1-Speed Units: Use SAE 20 wt. Part No. 737-0335 2-Speed Units: Use Part No. 737-0333 (Benzoil Gear Hydro Oil) Alternate ...

  • Troy-Bilt 13101 - GTX 16 - page 26

    Maintenance (continued) 26 T roubleshooting Chart Engine turns over but won't start. Engine will not turn over. Engine doesn't turn over but start light comes on. Starts only after repeated tries. Stalls in a few seconds. Stalls when hot. Idles rough. Engine overheats. Attachment drive inoperative. Cruise control inoperative. Excessive Vi ...

  • Troy-Bilt 13101 - GTX 16 - page 27

    Maintenance (continued) 27 Storing the T ractor Always store tractor in a dry and protected place when not in use. If tractor will not be used for a season, store it in the following manner. 1. CLEAN: Completely clean all accumulated dirt or grass from all parts – especially engine fins, transmission cooling fins and engine air intake screen. 2. ...

  • Troy-Bilt 13101 - GTX 16 - page 28

    © 1997 Garden Way Incorporated Printed in the U.S.A. For customer assistance, contact your nearest authorized dealer or: GARDEN WAY INCORPORATED • 1 Garden Way • Troy, New York U.S.A. 12180 Customer Service: 1-800-437-8686 • Technical Service: 1-800-520-5520 • Parts Service: 1-800-648-6776 • FAX: (518) 391-7332 Outside the U.S.A. and Can ...

Manufacturer Troy-Bilt Category Lawn Mower

Documents that we receive from a manufacturer of a Troy-Bilt 13101 - GTX 16 can be divided into several groups. They are, among others:
- Troy-Bilt technical drawings
- 13101 - GTX 16 manuals
- Troy-Bilt product data sheets
- information booklets
- or energy labels Troy-Bilt 13101 - GTX 16
All of them are important, but the most important information from the point of view of use of the device are in the user manual Troy-Bilt 13101 - GTX 16.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Troy-Bilt 13101 - GTX 16, service manual, brief instructions and user manuals Troy-Bilt 13101 - GTX 16. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Troy-Bilt 13101 - GTX 16.

Similar manuals

A complete manual for the device Troy-Bilt 13101 - GTX 16, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Troy-Bilt 13101 - GTX 16 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Troy-Bilt 13101 - GTX 16.

A complete Troy-Bilt manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Troy-Bilt 13101 - GTX 16 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Troy-Bilt 13101 - GTX 16, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Troy-Bilt 13101 - GTX 16, that we can find in the current document
3. Tips how to use the basic functions of the device Troy-Bilt 13101 - GTX 16 - which should help us in our first steps of using Troy-Bilt 13101 - GTX 16
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Troy-Bilt 13101 - GTX 16
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Troy-Bilt 13101 - GTX 16 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Troy-Bilt 13101 - GTX 16?

Use the form below

If you did not solve your problem by using a manual Troy-Bilt 13101 - GTX 16, ask a question using the form below. If a user had a similar problem with Troy-Bilt 13101 - GTX 16 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)