Manual Elektra Beckum BAS 316G DNB

16 pages 1.49 mb
Download

Go to site of 16

Summary
  • Elektra Beckum BAS 316G DNB - page 1

    115 166 9103 / 4802 - 1.1 BAS 316G DNB / BAS 316G WNB Betriebsanleitung . . . . . . . . . . . . . . . . . . . . . 3 Operating Instruction . . . . . . . . . . . . . . . . . 15 Instructions d'utilisation . . . . . . . . . . . . . . . 27 Manuale d’istruzioni . . . . . . . . . . . . . . . . . . 39 Manual de uso . . . . . . . . . . . . . . . . . ...

  • Elektra Beckum BAS 316G DNB - page 2

    2 D DEUTSCH ENG ENGLISH KONFORMITÄTSERKLÄRUNG DECLARATION OF CONFORMITY Wir erklären in alleiniger Verantwortlichkeit, dass dieses Produkt mit den folgenden Normen übereinstimmt* gemäß den Bestimmungen der Richtlinien** EG-Baumusterprüfung *** durchgeführt von **** We herewith declare in our sole repsonsibility that this product complies wi ...

  • Elektra Beckum BAS 316G DNB - page 3

    15 ENGLISH 1. Parts identification (standard delivery) 2 5 6 7 8 9 11 12 13 1 14 15 16 17 18 19 10 3 4 Front 1 Upper housing door 2 Setting knob for band saw blade tension 3 Upper band saw wheel 4 Setting knob for blade guard 5 Blade guard 6 Band saw blade 7 Saw table 8 Fence guide extru sion, graduated 9 Lower band saw wheel 10 Chip case 11 Rip fe ...

  • Elektra Beckum BAS 316G DNB - page 4

    16 ENGLISH 1. Parts identifi cation (standard delivery) .............. ......15 2. Please read first! ........... ............16 3. Safety ............... ................. .........16 3.1 Specified conditions of use .........16 3.2 General safety information ..........16 3.3 Safety devices ........... ................. .17 4. Special product featu ...

  • Elektra Beckum BAS 316G DNB - page 5

    17 ENGLISH Prevent body contact with earthed objects such as radiato rs, pipes, cooking stove s, refrigerat ors when operating this tool. • Do not use the powe r cable for any purpose it is not intended for. A Risk of injury by moving parts! • Do not operate th e tool without installed guards. • Always keep sufficient distan ce to the band sa ...

  • Elektra Beckum BAS 316G DNB - page 6

    18 ENGLISH Both housing doors must be closed while the machine is in use. Electronic motor brake The wear-free electronic moto r brake (inside the saw, not illustrated) causes the band saw blade to stop within 10 seconds after the saw is turned OFF. If the time to standstill exceeds 10 sec- onds the ON/OFF switch is faulty and needs to be replaced ...

  • Elektra Beckum BAS 316G DNB - page 7

    19 ENGLISH Rip fence The rip fence (33) is clam ped to the front. The rip fence can be used on both sides of the blade. A Danger! Start the saw only after the fol- lowing preparations have been com- pleted: − the saw is fastened; − the saw table is installed and aligned; − the V-belt tension checked; − the combination switch /plug is instal ...

  • Elektra Beckum BAS 316G DNB - page 8

    20 ENGLISH 7.4 Fence guide extrusion installation • Fasten the fence guide extrusion (40) with four each th umb screws and washers to the saw table. 7.5 Rip fence installation The rip fence can be used on both sides of the blade. 1. Fasten the fence extrusion (41) , using − two each pan-head screws, − two each w ashers and − two each knurle ...

  • Elektra Beckum BAS 316G DNB - page 9

    21 ENGLISH Position power supply cable so it does not interfere with the work and is not damaged. Protect power supply cable from heat, aggressive liquids and sharp edges. Use only rubber jacketed cable of suf- ficient l ead cross se ction. Do not pull on power supply cable to unplug. A Changing the direction of rota tion (3-phase motor only): Depe ...

  • Elektra Beckum BAS 316G DNB - page 10

    22 ENGLISH 8.1 Sawing 1. Choose and insta ll a table insert extrusion suitable for the type of cut to be performed: − table insert extrusion with a nar- row slot for standard cross cuts only; − table insert extrusion with b evel- led slot for bevel cuts also. 2. Adjust the band saw blade speed. 3. If necessary, adjust the table tilt. 4. Select ...

  • Elektra Beckum BAS 316G DNB - page 11

    23 ENGLISH 2. Loosen screws (61) . 3. Adjust position of guide bearing sup- port (62) so that the guide bearings (63) are positioned approx. 1 mm behind the to oth gullet. 4. Tighten screws (61) again. 5. Loosen screws (64) . 6. Press guide bearings (65) together (against the band sa w blade). 7. Turn the band saw whee l by hand in a clockwise dire ...

  • Elektra Beckum BAS 316G DNB - page 12

    24 ENGLISH 12. Adjust thrust bearing position (78) so it just touches the band saw blade. 13. Tighten screw (79) again. 14. Reinstall the saw table on th e upper table trunnion. 15. Reinstall th e fence guide extrusion for the rip fence. 9.5 Band saw tyre replace- ment Periodically check band saw tyres for wear. Replace only in pairs: 1. Remove ban ...

  • Elektra Beckum BAS 316G DNB - page 13

    25 ENGLISH A Danger! Repairs to power tools must be carried out by qual ified electricians only! Power tools in need of repair can b e sent to the service centre of your country. Refer to the spare parts list for the address. Please attach a description of the fault to the power tool. The machine's packing can be 10 0% recycled. Worn out power ...

  • Elektra Beckum BAS 316G DNB - page 14

    26 ENGLISH 15.1 Available band saw blades 15. Technical specifications Model BAS 316G DNB BAS 316G WNB Voltage V 400 (3~ 50 Hz) 230 (1~ 50 Hz) Capacity power input P1 effective shaft output P2 kW kW 0.74 0.55 0.74 0.55 Nominal current A 1.5 3.5 Fuse protection A 10 (time-lag or K-Auto- mat) 10 (time-lag or K-Auto- mat) Protection class IP 44 IP 44 ...

  • Elektra Beckum BAS 316G DNB - page 15

    63 A 090 900 4276 B 090 902 9244 C 090 902 9252 D 090 902 9260 E 090 902 9279 F 090 901 8811 G 090 903 0528 H 090 903 0536 I 090 901 8366 J 091 000 8048 K 090 901 0900 L 091 003 1260 M 013 001 1004 N 431 306 2258 O 091 101 8691 45° 3 0° 0° 22,5° 30° 45° 15° 15° 22,5° U3a0151.fm ...

  • Elektra Beckum BAS 316G DNB - page 16

    ZINDEL - Technische Dokumentation und Multimedia, www.zin del.de U4BA_EB3.fm www.elektra-beckum.de ...

Manufacturer Elektra Beckum Category Saw

Documents that we receive from a manufacturer of a Elektra Beckum BAS 316G DNB can be divided into several groups. They are, among others:
- Elektra Beckum technical drawings
- BAS 316G DNB manuals
- Elektra Beckum product data sheets
- information booklets
- or energy labels Elektra Beckum BAS 316G DNB
All of them are important, but the most important information from the point of view of use of the device are in the user manual Elektra Beckum BAS 316G DNB.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Elektra Beckum BAS 316G DNB, service manual, brief instructions and user manuals Elektra Beckum BAS 316G DNB. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Elektra Beckum BAS 316G DNB.

A complete manual for the device Elektra Beckum BAS 316G DNB, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Elektra Beckum BAS 316G DNB by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Elektra Beckum BAS 316G DNB.

A complete Elektra Beckum manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Elektra Beckum BAS 316G DNB - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Elektra Beckum BAS 316G DNB, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Elektra Beckum BAS 316G DNB, that we can find in the current document
3. Tips how to use the basic functions of the device Elektra Beckum BAS 316G DNB - which should help us in our first steps of using Elektra Beckum BAS 316G DNB
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Elektra Beckum BAS 316G DNB
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Elektra Beckum BAS 316G DNB in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Elektra Beckum BAS 316G DNB?

Use the form below

If you did not solve your problem by using a manual Elektra Beckum BAS 316G DNB, ask a question using the form below. If a user had a similar problem with Elektra Beckum BAS 316G DNB it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)