English dropdown-ico

Manual Kenwood LSF-1010

26 pages 0.43 mb
Download

Go to site of 26

Summary
  • Kenwood LSF-1010 - page 1

    LSF-1010 SPEAKER SYSTEM INSTR UCTION MANU AL KENW OOD CORPORA TION B61-1040-00 EN ...

  • Kenwood LSF-1010 - page 2

    LSF-1010 (EN) 2 DEUTSCH FRANÇAIS ESPAÑOL ITALIANO NEDERLANDS Before applying power Caution : Read this section carefully to ensure safe operation. Introduction Units are designed for operation as follows. Europe and U.K. ........................................................................ AC 230 V only Safety precautions Caution : Read this s ...

  • Kenwood LSF-1010 - page 3

    3 LSF-1010 (EN) DEUTSCH FRANÇAIS ESPAÑOL NEDERLANDS ITALIANO Accessories Unpacking Unpack the unit carefully and make sure that all accessories are put aside so they will not be lost. Examine the unit for any possibility of shipping damage. If your unit is damaged or fails to operate, notify y our dealer immediately . If your unit was shipped to ...

  • Kenwood LSF-1010 - page 4

    LSF-1010 (EN) 4 DEUTSCH FRANÇAIS ESPAÑOL ITALIANO NEDERLANDS Please read all of the safety and operating instructions before operating this appli- ance. Adhere to all warnings on the appliance and in the instruction manual. Follow all the safety and operating instructions. These safety and operating instructions should be retained for future refe ...

  • Kenwood LSF-1010 - page 5

    5 LSF-1010 (EN) DEUTSCH FRANÇAIS ESPAÑOL NEDERLANDS ITALIANO Caution : Read this page carefully to ensure safe operation. IMPORT ANT SAFEGUARDS 13. Damage requiring service – The appliance should be serviced by qualified service personnel when: A. The power-supply cord or the plug has been damaged. B. Objects have fallen, or liquid has been spi ...

  • Kenwood LSF-1010 - page 6

    LSF-1010 (EN) 6 DEUTSCH FRANÇAIS ESPAÑOL ITALIANO NEDERLANDS Location and Orientation Attaching the Cushions Attach four cushions to the base of the subwoofer, one at each corner, as shown below. The cushions prevent the subwoofer from sliding, and dampen its vibrations. (Cushions are included in the package.) • You can position the subwoofer v ...

  • Kenwood LSF-1010 - page 7

    7 LSF-1010 (EN) DEUTSCH FRANÇAIS ESPAÑOL NEDERLANDS ITALIANO Location and Orientation Location Precautions Interference with AM Reception The subwoofer utilizes digital circuitry to provide efficient signal amplification. Placing the subwoofer too close to your AM receiver (AM tuner) may therefore cause interference with AM reception. If you noti ...

  • Kenwood LSF-1010 - page 8

    LSF-1010 (EN) 8 DEUTSCH FRANÇAIS ESPAÑOL ITALIANO NEDERLANDS Setting Up the Satellite Speakers For standard setup, mount each speaker to a stand as described below. As an alternative to the standard setup, it is also possible to mount the speakers onto a wall or to set them up without the stand. For information about setup alternatives, see page ...

  • Kenwood LSF-1010 - page 9

    9 LSF-1010 (EN) DEUTSCH FRANÇAIS ESPAÑOL NEDERLANDS ITALIANO 2. Attach the arm to the stand. Push the clip open (see illustration) and fit onto the pole. 3. Plug the speaker cord into the base of the stand. Plug the cord extending from the speaker into the jack on the base of the stand. Clip Base Pole Plug the cord into the jack. Cord Y ou can ad ...

  • Kenwood LSF-1010 - page 10

    LSF-1010 (EN) 10 DEUTSCH FRANÇAIS ESPAÑOL ITALIANO NEDERLANDS Before Connecting... Making Connections Note Note 1. Be sure to connect all cables securely. Insecure connections may result in distortion or noise. 2. Always unplug the power cord before connecting or disconnecting cables. Leaving the power plugged in while making connections may resu ...

  • Kenwood LSF-1010 - page 11

    11 LSF-1010 (EN) DEUTSCH FRANÇAIS ESPAÑOL NEDERLANDS ITALIANO White stripe Connecting to Amp's SUBWOOFER PRE-OUT Jack Using the pin-plug audio cable that came with the subwoofer , connect the SUBWOOFER PRE-OUT jack on your amplifier or receiver to the L/ (MONO) LINE IN jac k on the subwoofer . CAUTION Do not plug in the power cord until you ...

  • Kenwood LSF-1010 - page 12

    LSF-1010 (EN) 12 DEUTSCH FRANÇAIS ESPAÑOL ITALIANO NEDERLANDS Connecting to Amp's Speaker Output T erminals Connect the FROM AMPLIFIER terminals on the subwoofer to the speaker output terminals on your amplifier or recei ver . Connect the TO SPEAKERS terminals on the subwoofer to your front speakers. Make all connections using speaker cord. ...

  • Kenwood LSF-1010 - page 13

    13 LSF-1010 (EN) DEUTSCH FRANÇAIS ESPAÑOL NEDERLANDS ITALIANO Connecting to Amp's Standard PRE-OUT Jacks Connect the PRE-OUT jacks on the amp or receiver to the LINE IN jacks on the subwoofer . Mak e the connection using pin-plug audio cable. (The cable is not included with the subwoofer .) CAUTION Do not plug in the power cord until you hav ...

  • Kenwood LSF-1010 - page 14

    LSF-1010 (EN) 14 DEUTSCH FRANÇAIS ESPAÑOL ITALIANO NEDERLANDS 1 POWER switch Press this switch to set the subwoofer's power on or off. 2 POWER indicator Indicator lights up when power is on. 3 VOLUME adjuster dial 4 PHASE switch 5 TURNOVER FREQUENCY adjuster dial Components and Their Functions Adjusting the Sound The V OLUME, TURNOVER FREQ U ...

  • Kenwood LSF-1010 - page 15

    15 LSF-1010 (EN) DEUTSCH FRANÇAIS ESPAÑOL NEDERLANDS ITALIANO Important Operating Notes Satellite Speakers 1. The satellite speak ers have a nominal impedance of 6 ohms. T o ensure safe and efficient speaker operation, be sure that your amplifier or receiver is able to work with 6-ohm speakers. 2. The speak er system’ s power capacity is indica ...

  • Kenwood LSF-1010 - page 16

    LSF-1010 (EN) 16 DEUTSCH FRANÇAIS ESPAÑOL ITALIANO NEDERLANDS Y ou can adjust the position of the speaker by c hanging the height and angle of the arm. Getting Ready to Adjust Loosen the two arm screws holding the arm in place (one screw on each side of the arm), so that you can move the arm up and down. 1. Remove the screw cap covering each arm ...

  • Kenwood LSF-1010 - page 17

    17 LSF-1010 (EN) DEUTSCH FRANÇAIS ESPAÑOL NEDERLANDS ITALIANO Adjusting the Satellite Speaker Position Adjusting the Arm Angle Y ou can set the arm to any of five dif ferent angles by adjusting the angle of the arm holders. 1. Remove the arm. 1 Loosen the two arm screws (one screw on each side of the arm) and pull the arm out. • Unplug the cord ...

  • Kenwood LSF-1010 - page 18

    LSF-1010 (EN) 18 DEUTSCH FRANÇAIS ESPAÑOL ITALIANO NEDERLANDS As an alternative to the standard setup, you can also mount the satellite speakers in any of the following configurations. • Sideways on the stand (“Offset mount”) • On the wall (“Wall mount”) • Without the stand (“Clip-on mount”) Offset Mount For information about ho ...

  • Kenwood LSF-1010 - page 19

    19 LSF-1010 (EN) DEUTSCH FRANÇAIS ESPAÑOL NEDERLANDS ITALIANO Other W ays to Set Up the Satellite Speakers W all Mount Y ou can mount the satellite speaker stands on the wall as described below. Precautions Please observe the following precautions when mounting speaker stands onto the wall. • Be sure that the wall you are using is strong enough ...

  • Kenwood LSF-1010 - page 20

    LSF-1010 (EN) 20 DEUTSCH FRANÇAIS ESPAÑOL ITALIANO NEDERLANDS 2 Attach supplied cushions to the bottom of the stand base. • The cushions will create a gap between the wall and the base through which speaker cord can pass. Please do not neglect to attach the cushions. 4. Reattach the clip to the pole. 1 First adhere the non-slip sheet onto the p ...

  • Kenwood LSF-1010 - page 21

    21 LSF-1010 (EN) DEUTSCH FRANÇAIS ESPAÑOL NEDERLANDS ITALIANO Clip-on Mount Use the following procedure to clip the speaker onto an object other than the base. Y ou can clip to either a cylindrical fixture (suc h as a thin pipe) or a flat-edge fixture (such as the edge of a bookshelf). Conditions If flat: Width should be 12 to 15 mm (about 0.5 to ...

  • Kenwood LSF-1010 - page 22

    LSF-1010 (EN) 22 DEUTSCH FRANÇAIS ESPAÑOL ITALIANO NEDERLANDS 3. Attach and fasten the arm. 1 Fit the arm through the holes in the arm holders, adjust it to the desire height, and then tighten the arm screws. 2 Place the screw caps back over the arm screws. Y ou may now want to readjust the angle of the speaker on the arm. Y ou can do this by loo ...

  • Kenwood LSF-1010 - page 23

    23 LSF-1010 (EN) DEUTSCH FRANÇAIS ESPAÑOL NEDERLANDS ITALIANO Cleaning Y ou can clean the panel for subwoofer and satellite speaker and casing by wip- ing with a sof t cloth. Never clean with alcohol, benz ene, paint thinner , or other such solvents, as these may cause discoloration. Contact Restorers Never use contact restoring agents to restore ...

  • Kenwood LSF-1010 - page 24

    LSF-1010 (EN) 24 DEUTSCH FRANÇAIS ESPAÑOL ITALIANO NEDERLANDS If the subwoofer does not seem to be working cor rectly , the following advice may help you correct the problem. T roubleshooting V olume is too low . * Speaker cords are reversed. * The phase setting is not appropriate. * The amp or receiver's PRE-OUT level is set to the minimum. ...

  • Kenwood LSF-1010 - page 25

    25 LSF-1010 (EN) DEUTSCH FRANÇAIS ESPAÑOL NEDERLANDS ITALIANO Specifications Subwoofer System ........................... Subwoofer system with built-in amplifier (Magnetically shielded) [Audio section] Rated Output Power ..................................... 40 W DIN (300 Hz, 6 Ω ) Output Power ...................................... 50 W RMS ( ...

  • Kenwood LSF-1010 - page 26

    For your records Record the serial number, found on the back of the subwoofer, in the spaces designated on the warranty card, and in the space provided at right. Refer to the model and serial numbers whenever you call upon your dealer for information or service on this product. Model ............................................ Serial Number ...... ...

Manufacturer Kenwood Category Speaker

Documents that we receive from a manufacturer of a Kenwood LSF-1010 can be divided into several groups. They are, among others:
- Kenwood technical drawings
- LSF-1010 manuals
- Kenwood product data sheets
- information booklets
- or energy labels Kenwood LSF-1010
All of them are important, but the most important information from the point of view of use of the device are in the user manual Kenwood LSF-1010.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Kenwood LSF-1010, service manual, brief instructions and user manuals Kenwood LSF-1010. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Kenwood LSF-1010.

Similar manuals

A complete manual for the device Kenwood LSF-1010, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Kenwood LSF-1010 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Kenwood LSF-1010.

A complete Kenwood manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Kenwood LSF-1010 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Kenwood LSF-1010, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Kenwood LSF-1010, that we can find in the current document
3. Tips how to use the basic functions of the device Kenwood LSF-1010 - which should help us in our first steps of using Kenwood LSF-1010
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Kenwood LSF-1010
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Kenwood LSF-1010 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Kenwood LSF-1010?

Use the form below

If you did not solve your problem by using a manual Kenwood LSF-1010, ask a question using the form below. If a user had a similar problem with Kenwood LSF-1010 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)