Manual Avalon Stoves Avanti PS

40 pages 0.95 mb
Download

Go to site of 40

Summary
  • Avalon Stoves Avanti PS - page 1

    Newport (Avanti PS) • Horizontal Or Vertical Vent • Freestanding Stove • Mobile Home Approved • Class A Chimney Retrofit Tested and Listed by Omni-Test Laboratories, Inc. Beaverton, Oregon ASTME-1509 1995, ULCC 1482 - - Please read this entire manual before installation and use of this pellet fuel-burning room heater. Failure to follow thes ...

  • Avalon Stoves Avanti PS - page 2

    ...

  • Avalon Stoves Avanti PS - page 3

    Introduction 1 Travis Industries Newport 290902 Introduction We welcome you as a new owner of a Newport (Avanti PS) pellet heater. In purchasing a Newport you have joined the growing ranks of concerned individuals whose selection of an energy system reflects both a concern for the environment and aesthetics. The Newport is one of the finest home he ...

  • Avalon Stoves Avanti PS - page 4

    2 Safety Precautions Travis Industries Newport 290902 • Do not operate the heater if you smell smoke coming from the heater. Turn the P OWER switch to "OFF", monitor your heater, and call your dealer. Ok • Contact your local building officials to obtain a permit and information on any installation restrictions or inspection requiremen ...

  • Avalon Stoves Avanti PS - page 5

    Safety Precautions 3 Travis Industries Newport 290902 • The heater will not operate during a power outage. If a power outage does occur, check the heater for smoke spillage and open a window if any smoke spills into the room. • This heater must be connected to a standard 115 V., 60 Hz grounded electrical outlet. Do not use an adapter plug or se ...

  • Avalon Stoves Avanti PS - page 6

    4 Table of Contents Travis Industries Newport 290902 Introduction Introduction ......................................................1 Important Information .........................................1 Safety Precautions Safety Precautions ............................................2 Specifications Heating Specifications ............................ ...

  • Avalon Stoves Avanti PS - page 7

    Specifications 5 Travis Industries Newport 290902 Heating Specifications: Approximate Maximum Heating Capacity (in square feet)* ................................. 800 to 1,600 Sq. Feet Burn Rate (Pounds per Hour)** ....................................................................... 1.0 to 3.5 Maximum Burn Time on Low Burn** .................... ...

  • Avalon Stoves Avanti PS - page 8

    6 Installation Travis Industries Newport 290902 Before You Begin READ THIS ENTIRE MANUAL BEFORE YOU INSTALL AND USE THIS HEATER. FAILURE TO FOLLOW THE INSTRUCTIONS MAY RESULT IN PROPERTY DAMAGE, BODILY INJURY, OR EVEN DEATH. Check with local building officials for any permits required for installation of this pellet heater and notify your insurance ...

  • Avalon Stoves Avanti PS - page 9

    Installation 7 Travis Industries Newport 290902 Clearances - Straight Installation 6 ” Minimum 3 ” Minimum 9 ” Minimum 3 ” Minimum Through the Wall Installations Interior Vertical Vents Floor Protection 6 ” Minimum 2 ” Minimum 9 ” Minimum “ Tee ” Clearances - Corner Installation 6 ” Minimum Through the Wall Vents 2 ” Minimum 2 ...

  • Avalon Stoves Avanti PS - page 10

    8 Installation Travis Industries Newport 290902 Venting the Pellet Stove • PELLET VENT MUST MAINTAIN A MINIMUM 3" CLEARANCE TO ANY COMBUSTIBLE (INSTALL VENT AT CLEARANCES SPECIFIED BY THE VENT MANUFACTURER). • DO NOT CONNECT THE PELLET VENT TO A VENT SERVING ANY OTHER APPLIANCE OR STOVE. • DO NOT INSTALL A FLUE DAMPER IN THE EXHAUST VENT ...

  • Avalon Stoves Avanti PS - page 11

    Installation 9 Travis Industries Newport 290902 Pellet Vent Type • Must be Type "L"(except for masonry fireplace installations) - or - connect the vent to a factory built type "A" chimney (use an adapter and seal all joints). Installing the Pellet Vent Seal each vent section by injecting a liberal amount of 500 ° F. RTV silic ...

  • Avalon Stoves Avanti PS - page 12

    10 Installation Travis Industries Newport 290902 Mobile Home Requirements • Outside air is required (used for combustion) - see the directions below. • The heater must be bolted to the floor (Some states do not require this; check with your local building department). See the illustration to the right. • The heater must be grounded to the ste ...

  • Avalon Stoves Avanti PS - page 13

    Installation 11 Travis Industries Newport 290902 Alcove Installation Requirements Whenever the pellet stove is placed in a location where the ceiling height is less than 7' tall, it is considered an alcove installation. Because of the reduced height, the installation requirements listed below must be met. • Minimum height is 60" • Min ...

  • Avalon Stoves Avanti PS - page 14

    12 Installation Travis Industries Newport 290902 Installation Example: Direct "Through-the-wall" Installation 3 ” Minimum 9 ” Minimum Floor Protection 6 ” Minimum House Shield (used to protect exterior wall from soot discoloration) 12 ” Minimum Horizontal Rain Cap Wall Thimble (note 3 ” clearance between vent and combustibles) O ...

  • Avalon Stoves Avanti PS - page 15

    Installation 13 Travis Industries Newport 290902 Installation Example: Interior Vertical Installation Type "L" Vent 6 ” Minimum 3 ” Minimum Floor Protection 2 ” Minimum 9 ” Minimum “ Tee ” Outside Air (optional) Floor Protection 24 ” Minimum Insulation must maintain 3 ” clearance. Outside air may be drawn from a ventilated ...

  • Avalon Stoves Avanti PS - page 16

    14 Installation Travis Industries Newport 290902 Installation Example: Class A Chimney Retrofit Type "L" Vent 6 ” Minimum 3 ” Minimum Floor Protection 2 ” Minimum 9 ” Minimum “ Tee ” Outside Air (optional) Floor Protection Outside air may be drawn from a ventilated crawl space. 2 ” Min. 3 ” Min. Class A Chimney Ceiling Sup ...

  • Avalon Stoves Avanti PS - page 17

    Installation 15 Travis Industries Newport 290902 Installation Example: Hearth Fireplace (Masonry or Z.C. (metal) ) “ L ” Vent Flex Section Outside air may be drawn from the ash cleanout. 6 ” Min. “ L ” Vent Storm Collar Vertical Cap Cover Plate (non-combustible) Silicone Seal the cover plate with silicone. NOTE: you will probably need a s ...

  • Avalon Stoves Avanti PS - page 18

    16 Operation Travis Industries Newport 290902 Safety Notice Read this entire manual (especially the "Safety Precautions" on pages 2 and 3) before using this stove. Failure to follow the instructions may result in property damage, bodily injury, or even death. ! Do not unplug the stove to turn it off. This stove relies upon electricity to ...

  • Avalon Stoves Avanti PS - page 19

    Operation 17 Travis Industries Newport 290902 Loading Pellets Lift the hopper lid to its vertical position. Pour pellets into the hopper until full. NOTE: The hopper holds approximately 55 pounds of pellets. P e t e l s l Make sure pellets are not left on this heat shield. The front edge of the hopper lid becomes very hot, do not touch the area bel ...

  • Avalon Stoves Avanti PS - page 20

    18 Operation Travis Industries Newport 290902 Manual Mode Manual mode requires the user to turn the heater on and off manually. To Start Press the "Manual Start" button. That's it. The stove automatically goes to a medium burn rate and high fan while the igniter starts the fire burning within 10 minutes. During this period the lowest ...

  • Avalon Stoves Avanti PS - page 21

    Operation 19 Travis Industries Newport 290902 Auto Mode Auto mode allows you to use a thermostat to control room temperature. The stove automatically turns on when the temperature drops below the thermostat setting. Once the stove reaches operating temperature, the stove then runs at the heat output setting selected. To Adjust Room Temperature (or ...

  • Avalon Stoves Avanti PS - page 22

    20 Operation Travis Industries Newport 290902 Restrictor Adjustment The restrictor “ fine tunes ” your appliance, adjusting the amount of air flowing to the flame. NOTE : the optimal restrictor position will vary over time as soot builds up inside the exhaust system. Not Enough Air: If clinkers develop or the flame appears lazy and slow to blow ...

  • Avalon Stoves Avanti PS - page 23

    Operation 21 Travis Industries Newport 290902 Start-Up Sequence This stove utilizes a start-up sequence whenever the mode switch is changed or the heater is started when cold. This is to ensure proper operation through all possible settings and operational states (hot or cold, pellets burning or not burning, etc.). This sequence over-rides all user ...

  • Avalon Stoves Avanti PS - page 24

    22 Maintenance Travis Industries Newport 290902 Daily Maintenance (whenever using the stove) Inspect the Burn When burning, the flames should be bright orange with an occasional ember jumping from the firepot. Make Sure Pellets are Not Piling Up If the pellets pile up over the burn pot, turn the mode switch to "OFF". The most likely cause ...

  • Avalon Stoves Avanti PS - page 25

    Maintenance 23 Travis Industries Newport 290902 Daily Maintenance (whenever using the stove) - Continued Check Firepot for Clinkers If the flames seem to be coming only from the sides, or are orange/black, turn the stove off and check for clinkers. The most likely causes are: • Poor pellet quality • The door or glass has an air leak • The exh ...

  • Avalon Stoves Avanti PS - page 26

    24 Maintenance Travis Industries Newport 290902 Bi-Weekly Maintenance (or every 10 bags of pellets) Clean the Heat Exchange Tubes With the stove cool (or using the door latch tool), move the heat exchange cleaner up and down several times. Keep the door closed so the flyash does not enter the room. Open the hopper lid. The front edge of the hopper ...

  • Avalon Stoves Avanti PS - page 27

    Maintenance 25 Travis Industries Newport 290902 Bi-Weekly Maintenance (or every 10 bags of pellets) - Continued Opening The Door Use the door latch tool to open the latch. The tool can be hung in one of the holes on the back side of the stove. a b Latch Door Latch Tool Door Frame Door Latch Tool Twist Counter- Clockwise to Open. Swing the door open ...

  • Avalon Stoves Avanti PS - page 28

    26 Maintenance Travis Industries Newport 290902 Bi-Weekly Maintenance (or every 10 bags of pellets) - Continued Sweep Ash Into Ashpan HINT: The more often you clean out the flyash, the more efficient your heater will burn. Swing the side ash trap door up. Lift it up and away from the firebox. Repeat for the opposite side. Lift the firepot out of it ...

  • Avalon Stoves Avanti PS - page 29

    Maintenance 27 Travis Industries Newport 290902 Bi-Weekly Maintenance (or every 10 bags of pellets) - Continued Check Ashpan, Dispose if necessary The ash pan has a built in handle to ease transportation of the ashes. NOTE : When replacing the ashpan make sure it is pushed all the way in. Disposal of Ashes – Ashes should be placed in a metal cont ...

  • Avalon Stoves Avanti PS - page 30

    28 Maintenance Travis Industries Newport 290902 Yearly Maintenance (or every two tons) WARNING: Disconnect the power cord prior to conducting service. The following section details extensive maintenance procedures. We strongly suggest these items be carried out by a trained service technician, possibly by a service agreement set up with your dealer ...

  • Avalon Stoves Avanti PS - page 31

    Maintenance 29 Travis Industries Newport 290902 Yearly Maintenance (or every two tons) - Continued Clean the Exhaust Blower (make sure the stove is cool and unplugged) a Open the hopper lid and remove the screw hlding the left door in place. Swing the left side panel open. Remove the six screws holding the exhaust blower motor in place. b 11/32&quo ...

  • Avalon Stoves Avanti PS - page 32

    30 Maintenance Travis Industries Newport 290902 Yearly Maintenance (or every two tons) - Continued Check for Air Leaks Around the Door, Glass, and Ashpan ! Air leaks into the firebox will decrease the stove's performance greatly, leading to excessive sooting, inefficient burning, and perhaps a malfunction. • Test the door seal by shutting th ...

  • Avalon Stoves Avanti PS - page 33

    Normal Operating Sounds 3 1 Travis Industries Newport 290902 Auger Motor When feeding pellets, you may hear the intermittent buzz of this motor running. Convection Fan The modern high efficiency fan may produce a low hum, particularly on "HIGH". This sound will change as the FAN dial is turned. Heat Exchanger Tubes You may hear the heated ...

  • Avalon Stoves Avanti PS - page 34

    32 Safety Label Travis Industries Newport 290902 W ARNING - DO NOT REMOVE OR COVER THIS LABEL R Listed Pelletized Solid Fuel Burning Appliance Also for Use in Mobile Homes Model: A vanti-PS Serial No: Report No. 476-1407-00 (May , 1997) T ested to: UL 1482/ULC S627/CSA B366.2/ASTM E 1509-95 Maximum Input Rating: 3.5 lbs (1.60kg)/hr Electrical Ratin ...

  • Avalon Stoves Avanti PS - page 35

    Limited 7 Year Warranty 3 3 Travis Industries Newport 290902 To register your TRAVIS INDUSTRIES, INC. 7 Year Warranty, complete the enclosed warranty card and mail it within ten (10) days of the appliance purchase date to: TRAVIS INDUSTRIES, INC., 10850 117th Place N.E., Kirkland, Washington 98033. TRAVIS INDUSTRIES, INC. warrants this appliance (a ...

  • Avalon Stoves Avanti PS - page 36

    34 Optional Equipment Travis Industries Newport 290902 Thermostat (Part # 99300650) ! Do not connect 120 VAC to the thermostat circuit of this heater (do not use a household thermostat used for a wall-board or other electical heater). 1 Attach the thermostat wire to the circuit board (see the illustration to the right). Route the wire through the b ...

  • Avalon Stoves Avanti PS - page 37

    Optional Equipment 35 Travis Industries Newport 290902 Remote Thermostat • Follow the instructions included with the remote thermostat for installation. Using the Remote Thermostat The remote thermostat has a 1 to 2 minute lag time between the time the thermostat is turned up and the heater turns on. Included with the remote thermostat is a set o ...

  • Avalon Stoves Avanti PS - page 38

    36 Optional Equipment Travis Industries Newport 290902 Optional Log (Part # 98900126) ! Make sure the heater has fully cooled before installation. 1 Open the door (see the instructions included with the owner’s manual. 2 Attach the two log shelf legs to the cross brace with the four included nuts. Make sure to use the correct leg for each side. R ...

  • Avalon Stoves Avanti PS - page 39

    Optional Equipment 37 Travis Industries Newport 290902 Optional Gold Grill (part # 93005034) Phillips Screwdriver Use a phillips screwdriver to remove the two screws holding the black trim in place. Open the hopper lid. Use the same screws to attach the gold trim. a b c Optional Gold Door (part # 99300531) Remove the door by sliding it up and off t ...

  • Avalon Stoves Avanti PS - page 40

    38 Index Travis Industries Newport 290902 Adjusting the Fan Speed ...................................... 2 0 Air Leaks .......................................................... 3 0 Alcove Installation Requirement s .......................... 1 1 Ashpan (Opening and Disposing Ashes ) ................. 2 7 AUGER ON Ligh t ........................... ...

Manufacturer Avalon Stoves Category Stove

Documents that we receive from a manufacturer of a Avalon Stoves Avanti PS can be divided into several groups. They are, among others:
- Avalon Stoves technical drawings
- Avanti PS manuals
- Avalon Stoves product data sheets
- information booklets
- or energy labels Avalon Stoves Avanti PS
All of them are important, but the most important information from the point of view of use of the device are in the user manual Avalon Stoves Avanti PS.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Avalon Stoves Avanti PS, service manual, brief instructions and user manuals Avalon Stoves Avanti PS. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Avalon Stoves Avanti PS.

A complete manual for the device Avalon Stoves Avanti PS, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Avalon Stoves Avanti PS by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Avalon Stoves Avanti PS.

A complete Avalon Stoves manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Avalon Stoves Avanti PS - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Avalon Stoves Avanti PS, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Avalon Stoves Avanti PS, that we can find in the current document
3. Tips how to use the basic functions of the device Avalon Stoves Avanti PS - which should help us in our first steps of using Avalon Stoves Avanti PS
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Avalon Stoves Avanti PS
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Avalon Stoves Avanti PS in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Avalon Stoves Avanti PS?

Use the form below

If you did not solve your problem by using a manual Avalon Stoves Avanti PS, ask a question using the form below. If a user had a similar problem with Avalon Stoves Avanti PS it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)