English dropdown-ico

Manual JBL P12SW

31 pages 2.82 mb
Download

Go to site of 31

Summary
  • JBL P12SW - page 1

    Models: Northridge ™ E -Series E 250P Performance S eries P12S W Powered Subwoofer s Service Manual JBL Cons umer Produc ts 250 Cr ossw ays Par k D r. W oodbury , New Y or k 11797 Rev3 4/2006 ...

  • JBL P12SW - page 2

    - CONTENTS - BASIC SPECIF I CATIO N S ……………. ……..…………..1 SAFET Y INF ORMAT ION …………….……..….………..2 E250P P ACKING……..………………….….….….……...3 P12SW PACKING……..……………………….…………4 DETAILED SPECI FICAT IONS ………. ……. .…………..5 CONNECTIONS…? ...

  • JBL P12SW - page 3

    W ar ning Any person performing service of this unit will be exposed to hazardous voltages and the risk of electric shock. It is assumed that any person who removes the amplifier fr om this cabinet has been properly trained in pr otecting against avoidable injury and shock. Therefor e, any service procedur es are to be performed by qualified servic ...

  • JBL P12SW - page 4

    1 5 3 14 2 4 E250P Packaging Ref# Part N umbe r Description Qty 1 3512 49-0 02 M ANUAL, O W NER- E25 0P/ E250 P 1 2 35 1249-0 01 CAR TON,M ASTER -E 250P (BEEC H M ODEL) 1 3512 49-0 03 CAR TON,M ASTER -E 250P (BLAC K M ODEL) 1 3508 84-0 03 CAR TON,M ASTER -E 250P (C HERRY M ODEL) 1 3 3512 52-0 01 PAD,EN D ,TOP- E250 P 1 4 3512 52-0 02 PAD,EN D ,BOT- ...

  • JBL P12SW - page 5

    1 5 3 2 4 Packaging P12SW 6 Ref # Pa rt Numbe r De scription Qty 1 361803- 001 P12S W Owner ’s M anual 1 2 3618 13-0 01 P12S W Out er Car ton 1 3 351252- 001 Packin g Foam (T op) 1 4 351252- 002 Packin g Foam (Bot tom) 1 5 3383 81-0 01 W a rr a nty C ard 1 6 3 52024 -003 Fro nt Grille 1 4 ...

  • JBL P12SW - page 6

    JBL E250P/P12SW Powered Sub/ Plate Amp LINE VOLTAGE Yes/No Hi/Lo Line Nom. Unit Notes US 120vac/60Hz Yes 108-132 120 Vrms Normal Operation EU 230vac/50-60Hz Yes 207-264 230 Vrms Normal operation, MOMS required Parameter Specification Unit QA Test Limits Conditions Notes Amp Section Type (Class AB, D, other) D n/a n/a Load Impedance (speaker) 5.6 Oh ...

  • JBL P12SW - page 7

    Parameter Specification Unit QA Test Limits Conditions Notes Turn-on Transient 50 mV-peak 2v-pp @ Speaker Outputs AC Line cycled from OFF to ON Turn-off Transient 50 mV-peak 2v-pp @ Speaker Outputs AC Line cycled from ON to OFF Efficiency Efficiency 65 % 64 Nominal Line voltage 120 VAC Stand-by Input Power 24 Watts 26 @ nom. line voltage Maximum al ...

  • JBL P12SW - page 8

    Analog Receiver/Processor – Speaker -Level Connections Use this installation method only with an analog receiver/ processor that does not have digital processing or bass management, and also does not have a subwoofer output or a volume-controlled preamp (line-) level output: Connect the speaker wires for both your main left and right speakers, an ...

  • JBL P12SW - page 9

    Digital Receiver/Processor – LFE Connection Use this installation method for Dolby Digital, DTS ® or other digital surround processors that have bass-management programming, or for analog receivers/processors that have a filtered subwoofer output: IMPORT ANT : Make sure that the LFE toggle switch on the subwoofer is in the “LFE” position. Us ...

  • JBL P12SW - page 10

    OPERA TION When the unit is plugged in and the power switch is on and no signal is received, the LED on the top of the unit will turn red. When a signal is present, the LED will turn green. Note: It will take several min- utes for the LED to turn from green to red after the input signal to the subwoofer is removed. Due to JBL ’ s unique high-outp ...

  • JBL P12SW - page 11

    TROUBLESHOOTING If you used the high-level (speaker) inputs and there is no sound from any of the speakers: • Check that the receiver/ amplifier is on and a source is playing. • Check that the powered subwoofer is plugged into an active electrical outlet and is switched on. • Check all wires and connec- tions between the receiver/ amplifier a ...

  • JBL P12SW - page 12

    Ref# Part N umbe r Description Qty 6 3513 48-0 01 PLAT E,LED/ LOGO- E25 0P 1 7 3381 25-0 02 ASY,L ED-E2 50P/E 250P 1 8 3364 86-0 01 ASY,F OOT ,PLSTC - E 250P 4 9 763- 3111 0-4 0 SCR EW, 8 X 2 1/ 2,TR,PH ,PB ,BLK Z INC ,LC S (F OOT) 4 10 9083 02-012 SCRE W , P B,HXS, #6x.7 5,ZIN C ( LOGO P LATE) 4 11 9038 02-016 SCR EW, P B,HXS, #8x1" ,ZIN C ( ...

  • JBL P12SW - page 13

    9 8 Amplifier – Not for Sale Exploded V iew P 12S W Ref # Pa rt Numbe r De scription Qty 1 352024- 003 ASY, GRI LLE, BLK, F RNT 1 2 3332 49-0 01 CU P,GRI LLE 4 3 88 2-41 110-1 2 SCRE W , 6 X 3/ 4,PAN ,PH,P B,BLK ZI NC,LC S (A MP LIFI ER) 10 4 903802- 016 SCRE W , P B,HX S,#8x 1",ZI NC ( W OOFER ) 8 5 3512 43-0 01 RI NG,TRI M ,12" 1 6 33 ...

  • JBL P12SW - page 14

    TEST SET-UP A ND PROCEDURE Ge nera l F unc ti o n UUT = Unit Under Test 1) Connect a pai r of level input cables (RCA) f rom signal generator to eit her Right or Left Level input on UUT. LEVEL contr ol shoul d be f ull count ercl ock wise (MI N). Make sure the LF E/Norm al sw i t ch is in the NO RMAL positi on. 2) Tur n on gener at or, adjust t o 1 ...

  • JBL P12SW - page 15

    & P10SW & P12SW 14 E250P/ P12SW subwoo fers ...

  • JBL P12SW - page 16

    JBL I n corporated 250 C ross ways Park D r. W oodbury, N e w Yor k 11797 (516) 496-3400 Serv ice Bu lletin Serv ice bul leti n # JBL2005- 01 Decem ber 2005 W a rranty l abor rate: M IN OR repair To: All JBL Servi ce Center s M odel: E150P, E250P Subwoofers Subject: “ Chir p” N oise on Pow er- Up I n t he ev ent yo u recei ve an E150P o r E250P ...

  • JBL P12SW - page 17

    TECH TIPS Troubl esh ooting tips a nd s olu tion s to comm on ser v ice pr oblems For models: E150P,E 250P T I P# JBLT T 2003-04 Rev 2 P10S W, P12S W PB10,P B12 (Revision 2) * Su b ject: Replaci ng MOS FETS Q18, Q22 In the event you need to replace MOSFET transisto rs Q18 or Q22 as part of a repair, i t is im portant to use ONLY : • JBL part# 051 ...

  • JBL P12SW - page 18

    A. Power Amp Section Resistance Check Resistance from S+ (SPK O/P) to GND should be >1M Ω (NO LOAD) Resistance from V+ (C6 P+) to V- (C8 P-) gradually Fully CHARGED should read >10k Ω Resistance from V+ (C6 P+) to S+ (SPK O/P) should read >1M Ω Resistance from V- (C8 P-) to S+ (SPK O/P) should read >1M Ω 2. Power Up LED RED With ...

  • JBL P12SW - page 19

    - Voltage measurements OP AMP U2(1) U2(14) U2(8) U3(7) U3(1) U3(14) U3(8) U5(7) U5(1) SPEAKER O/P 306.9mV 461mV 460mV 658mV 628mV 598mV 2.326V 2.02V 3.57V 23.33V 2. High Level Input Sensitivity -Set up Turn level, X’OVER FREQ POT Fully CW and LFE switch off Set Generator at 1.3V@50Hz Signal to High level input -Voltage measurements 15.3V at speak ...

  • JBL P12SW - page 20

    CAUTION : SPEAKER OUTPUT IS FLOATING AND IS NOT PROTECTED AGAINST A SHORT TO GROUND. ALL TEST INSTRUMENTS CONNECTED TO THE OUTPUT MUST BE FLOATING. ATTACH THE SCOPE PROBE TIP TO S - and REFERENCE LEAD TO S+. (A 10mV signal may need from the input to trigger the Switch turn on) no no yes yes no no yes yes no no yes yes no no yes yes START Check +/-1 ...

  • JBL P12SW - page 21

    20 E250P/ P12SW subwoo fers ...

  • JBL P12SW - page 22

    21 E250P/ P12SW subwoo fers ...

  • JBL P12SW - page 23

    22 E250P/ P12SW subwoo fers ...

  • JBL P12SW - page 24

    23 E250P/ P12SW subwoo fers ...

  • JBL P12SW - page 25

    E250P/P12SW (120v) Electrical Parts List Part Number Description Reference Designator Qty Resistors 020-220497-120 Carbon Film 2K2 1/4W J R11 1 021-100401-120 MOF Resistor 1K 1W J R103 1 021-120403-020 MOF Resistor 1K2 3WS J 8x20 R9 1 021-120405-020 MOF Resistor 1K2 5WS J 8x25 R6 1 021-220202-120 MOF Resistor 22R 2W(S) J MB TYPE 15x8 R10 1 022-5000 ...

  • JBL P12SW - page 26

    Part Number Description Reference Designator Qty 024-470698-120 SMD Resistor 470K 1/8W J 0805 R70 1 024-470798-120 SMD Resistor 4M7 1/8W J 0805 R60 1 024-487498-100 SMD Resistor 4K87 1/8W F 0805 R51,53 2 024-510398-120 SMD Resistor 510R 1/8W J 0805 R57 1 024-560598-120 SMD Resistor 56K 1/8W J 0805 R122 1 024-620398-100 SMD Resistor 620R 1/8W F 0805 ...

  • JBL P12SW - page 27

    Part Number Description Reference Designator Qty 051-005600-100 PNP Transistor PN:MPSW56RLRA TO-92 (ON) Q3 1 051-222200-100 NPN Transistor PN:MPS2222ARLRA TO-92 Q21 1 051-290700-100 PNP Transistor PN:MPS2907A RLRA TO-92 Q19,23 2 051-540101-000 PNP Transistor PN:2N5401 TO-92 Q1 1 051-555100-000 NPN Transistor PN:2N5551 TO-92 Q17 1 051-640001-000 MOS ...

  • JBL P12SW - page 28

    Part Number Description Reference Designator Qty 063-010012-000 Brckt for pwr transistor P/N:TRK-1 063-321100-001 E250P Faceplate 322x105.7x15mm BLK (94V0)ABS E250P 063-321101-000ZR P12SW Faceplate 322x105.7x15mm BLK (94V0)ABS P12SW 063-531808-000 Bucket 322x105.7x146.5mm blk (94VO) 071-100608-100 Fiber Washer OD=8mm ID=3.2 t=1 (red) 071-100851-000 ...

  • JBL P12SW - page 29

    OPAMP, QUAD TL074CDR U2, 3 OPAMP, DUAL TL072CDR SO-8, NJM4558M-TE3 U5, 6, 4 IR2111 HALF-BRIDGE DRIVER U7 2 Base 3 Collector 1 Emitter 1 2 3 2N5401 Q1 2 Base 3 Collector 1 Emitter 1 2 3 MPSW06RLRA, MPSW56RLRAMPQ, MPS2222ARLRA, 2N2907A, 2N5551, Q2, 16, 3, 21, 19, 23, 17 MOSFET IRF640 Q18, 22 TIP31C Q4 MMBT3904LTI SOT23, MMBT3906LTI SOT23, DTC114EK SM ...

  • JBL P12SW - page 30

    SCHEMATICS NOTE: THIS VOLTAGE IS REFERENCED TO -V, NOT CIRCUIT GROUND NOTE: THIS VOLTAGE IS REFERENCED TO -V, NOT CIRCUIT GROUND 29 E250P/ P12SW subwoo fers P12SW Value of C65 = 47uf See service bulletin for E250P ...

  • JBL P12SW - page 31

    30 E250P/ P12SW subwoo fers NOTE: THIS VOLTAGE IS REFERENCED TO -V, NOT CIRCUIT GROUND ...

Manufacturer JBL Category Speaker System

Documents that we receive from a manufacturer of a JBL P12SW can be divided into several groups. They are, among others:
- JBL technical drawings
- P12SW manuals
- JBL product data sheets
- information booklets
- or energy labels JBL P12SW
All of them are important, but the most important information from the point of view of use of the device are in the user manual JBL P12SW.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals JBL P12SW, service manual, brief instructions and user manuals JBL P12SW. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product JBL P12SW.

Similar manuals

A complete manual for the device JBL P12SW, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use JBL P12SW by users. Manuals are usually written by a technical writer, but in a language understandable to all users of JBL P12SW.

A complete JBL manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual JBL P12SW - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the JBL P12SW, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the JBL P12SW, that we can find in the current document
3. Tips how to use the basic functions of the device JBL P12SW - which should help us in our first steps of using JBL P12SW
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with JBL P12SW
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of JBL P12SW in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning JBL P12SW?

Use the form below

If you did not solve your problem by using a manual JBL P12SW, ask a question using the form below. If a user had a similar problem with JBL P12SW it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)