Manual Zonet ZSR1134WE

44 pages Not applicable
Download

Go to site of 44

Summary
  • Zonet ZSR1134WE - page 1

    ...

  • Zonet ZSR1134WE - page 2

    Copyright State ment is the re gistered trademark of Zonet T echnology Inc. All the products and product names mentio ned herein are the trademarks or registered trademarks of their respective holder s. Copyright of the whole product as in tegration, including its accessor ies and software, belongs to Z onet T echnology Inc. W ithout the pe rmissio ...

  • Zonet ZSR1134WE - page 3

    Table of Conten ts Chapter 1 Introduction ......... ....... ........ ....... ........ ........ .... ....... ........ ....... 1 W e lcome . ....... ........ ........ ....... ........ ..... ....... ....... ........ ....... ........ ....... ...... 1 Contents of P ackage ......... ....... ........ ....... ..... ....... ........ ........ ....... ....... ...

  • Zonet ZSR1134WE - page 4

    1 Chapter 1 Introduction Welcome Thank you for purchasing Z onet ZSR1134WE – 802.11g w ireless broadband router! Thi s h igh cost -efficiency router is the best choice for Small office / Home office users, all co mputers and network devices can share a single xDSL / cable modem in ternet co nnection at high sp eed. Easy install procedures allows ...

  • Zonet ZSR1134WE - page 5

    2 Getting to Kno w Your ZSR1134WE Front Panel LED Indicator Status Description ON Indicates ZSR1134WE is receiving power SYS Flashing Indicates ZSR1134WE works normally. ON Indicates WA N port is connected WAN Flashing Indicates WAN activity (transferring or receiving data) ON Indicates LAN port is connected LAN(1/2/3/4) Flashing Indicates LAN acti ...

  • Zonet ZSR1134WE - page 6

    3 Rear Panel Item Name Description POWER P ower connector , connects to power ad apter 1-4 (LAN Ports) Local Area Network (LAN) ports 1 to 4 WAN Wide Area Network (WAN / Internet) port. DEFAULT Res et ZSR1134WE to factory default settings (clear all settings). Antenna The antenna is 2dBi dipole antenna. There is a way to reset the Z SR1134WE’s fa ...

  • Zonet ZSR1134WE - page 7

    4 Chapter 2 Hardware Installation Please follow the following instruction to bu ild the network connection between your ZSR1134WE and y our computers, network devices: 1. Connect th e power adapter to the wall socket, and then connect it to the Power socket of ZSR1134WE. 2. Connect all your co mputers, network devices (network -enabled co nsumer de ...

  • Zonet ZSR1134WE - page 8

    5 3. Connect your xDSL / cable modem to the WAN port of ZSR1134W E by Ethernet cable. 4. Please check all LEDs on the front panel. SYS LED s hould be s teadily on, WAN and LAN LEDs shoul d be on if the computer / network device connected to the respective port of ZSR1134WE is powered on and cor rectly connected. If any LED you expected is not on, p ...

  • Zonet ZSR1134WE - page 9

    6 Chapter 3 Connect Your ZSR11 34WE How to Set the Network Config urations for My Computer 1. Click Start → → → → Control Panel 2. Click Network and Internet Connections → → → → Network Connections ...

  • Zonet ZSR1134WE - page 10

    7 3. Right click Local Area Netwo rk Connection and select Properties . 4. Select Internet Proto col (TCP/IP) and click Properties . ...

  • Zonet ZSR1134WE - page 11

    8 5. Select Obtain a n IP addres s autom atically and Obta in DNS server address automatically . Click OK to save the configur ations. Additional Setti ngs for Wireless Client If you choose to access ZSR1 134WE via a wireless client, please also verify the following: 1. Make sure your PC is equipped with 802.11 g or 802.11b wireless adapter and has ...

  • Zonet ZSR1134WE - page 12

    9 How to Check t he Network Conn ection 1. Select Start → → → → Program s → → → → Accessories → → → → Command Prompt . 2. Input ping 192.168.1.1 and press Enter . If the screen displays as below, it means your PC is connected to y our rou ter successfully . If not, please make sure the hardware installation and network adapt ...

  • Zonet ZSR1134WE - page 13

    10 Chapter 4 Basic Confi gurations This section is to sh ow you how to confi gure your new Z SR1134WE through the W e b-based Configuration Utilit y . How to Access t he Web-based Conf iguration Utility 1. After your computer obtained an IP addre ss from ZSR1134WE, please start your web browse r , and i nput the default IP a ddress of ZSR1134WE htt ...

  • Zonet ZSR1134WE - page 14

    1 1 Quick Setup Wizard 1. When Convenient Setup show up, Click Next to continue. a. Operation Mode ...

  • Zonet ZSR1134WE - page 15

    12  Gateway ZSR1134WE is supposed to connect to Internet via ADSL/Cable Modem. The NA T is enabled and PCs in four LAN por ts share the same IP to ISP through W AN port. The co nnection type can be setup in WAN page by using PPP oE, DHCP client, PPTP client or static IP .  Bridge All Ethernet ports and wireless interface are bridged together ...

  • Zonet ZSR1134WE - page 16

    13 c. LAN Setup LAN Setup page allows y ou to specify a private IP address for ZSR1134 WE’ s LAN ports as well as a subnet mask for your LAN segment.  I P Address ZSR1134WE’ s LAN IP address (not your PC’ s IP address). Once you modify the IP address, you need to remember it for the W eb-based Utility login next time. Default v alue is 19 ...

  • Zonet ZSR1134WE - page 17

    14  St atic IP Y our ISP has given you an IP address already  DH CP Client Y our ISP w ill au tomatically giv e you an IP add ress. And the n cl ick Next .  PPPoE Y our ISP requires PPPoE connecti on  PPTP Y our ISP requires you to use a Point -to-P oint T unneling Protoco l (PPTP) connection. e. Wireless Basic Settings  Mode Support ...

  • Zonet ZSR1134WE - page 18

    15 f. Wireless Security  Encryp tion Mode ZSR1134WE provides security authentication methods including: None, WEP, WPA(TKIP), WPA2(AES) and W PA2 Mixed. None means do not encrypt wireless data.  WEP WEP (Wired E quivalent Privacy) is an encryption method used to protect your wire less data co mmunications. WEP uses a combination of 64-bit or ...

  • Zonet ZSR1134WE - page 19

    16 LAN Setup  I P Address ZSR1134WE’ s LAN IP address (not your PC’s IP addre ss). Once you modify the IP addr ess, you need to remember it for the W e b-based Utility login next time. Default v alue is 19 2.168.1.1  Subnet Ma sk ZSR1134WE’ s subnet mask for measurement of th e network s ize. Default v alue is 255.255 .255.0.  Defaul ...

  • Zonet ZSR1134WE - page 20

    17  Clone MAC addr ess Replace the LAN MAC address with the MAC address of that PC. Internet Setup  W AN Access Type  Static IP address IP address provided by your ISP .  DHCP Client Y our ISP will automatically give you an IP address.  P PPoE Y our ISP requires PPPoE connecti on  P PTP Y our ISP requires you to use a Point -to-P ...

  • Zonet ZSR1134WE - page 21

    18  M TU Maximum T ransmission Unit. It is the size of largest datagram that can be sent over a network. The de fault v alue is 1412. Do NOT modify it unless necessary .  DN S Y ou can specify a DNS server that you wish to use  Clone MAC Addr ess Replace the WAN MAC address with the MAC address of that PC ...

  • Zonet ZSR1134WE - page 22

    19 Chapter 5 Wireless Settings Basic Settings  Band Support 802.11b/g mixed, 802.11b and 802 .11g modes.  Mode Support AP , Client, WDS, AP+WDS mode.  Network Type Support infr astructure and hoc.  SSID It’ s the name of your wireless network.  Channel Number Select the channel used for wireless communication from drop-down list. A ...

  • Zonet ZSR1134WE - page 23

    20  Enable Mac Clone Click the Enable M AC Clone checkbox will copy the MAC address of your PC to the WLAN MAC.  Enable Universal Repeater Mode T o Enable Universal Repeater M ode, Acting as AP and client simultaneously Advanced Setti ngs  A uthentication Type  Op en System : Wire less stations can associate with ZSR1 13WE without WEP e ...

  • Zonet ZSR1134WE - page 24

    21  Fr agment Threshold Specify the maxi mum size of packet during the fr agmentation of dat a to be tran smitted. Default value is 2346.  RTS Threshold When the pack et size is small er t he R TS threshold, ZSR1134WE will not use the RTS/CTS mechanism to send this packet. Defau lt v alue is 2 347.  Beaco n Interval The interv al of time Z ...

  • Zonet ZSR1134WE - page 25

    22 Security Setup a. None ...

  • Zonet ZSR1134WE - page 26

    23 b. WEP (Set WEP Key) WEP (Wired Equivalent Privacy) is an encryption method u sed to protect your wireless data communications. WEP uses a combination of 64 -bit or 128-bit keys to provide access control to your network and encryption security for every data transmission.  Key Length Select the WEP Key Length from 64-bit o r 128-bit. Larger W ...

  • Zonet ZSR1134WE - page 27

    24 c. 802.1x This security mode is used when a RADIUS ser ver is co nnected to ZSR1134WE. IEEE 802.1x is an auth entication protocol. Every use r must use a v alid accoun t to login to ZSR1 134WE befo re accessing the w ireless LAN. The authentication is proce ssed by a RADIUS server . T his mo de also uses WEP to encrypt the data during communicat ...

  • Zonet ZSR1134WE - page 28

    25 d. WPA Wi-Fi Protected Access (WP A) is a n advanced security standar d. It uses TKIP and AES to change the encryption key fre quently.  WPA Cipher Suite Select one encryption type, TKIP or AES .  Pre-Shared Key Forma t  Passphrase: alphanumeric format  Hexadecimal Digits: in the A -F , a-f and 0-9 range ...

  • Zonet ZSR1134WE - page 29

    26 Access Control This function wi ll help you to prevent un authorized use rs from co nnecting to ZSR1134WE; only those wireless devices who hav e th e MAC address you assigned her e can gain access to your Z SR1134WE. Y ou can u se this function wi th o ther security measure s described in previous section, to create a safer wireless environment. ...

  • Zonet ZSR1134WE - page 30

    27  Disable WPS Select the checkbox to disable WPS function, default setting is Enable .  WPS Status  Configured: means WPS feature is enabled and goes into effe ct.  UnConfigured: means WPS is not use d.  Self-PIN Number : : : : The PIN code used by default.  Push-Button Configuration If you want to use PBC, you ha ve to ...

  • Zonet ZSR1134WE - page 31

    28 Note: First, you should set ZSR1134 WE in AP mode a t Wireless Basic Settings page, and then select the Enable WDS checkbox in th is page. Two wireless routers must use the same band, channel number, and security setting. Site Survey ...

  • Zonet ZSR1134WE - page 32

    29 Chapter 6 Advanced Settings Applications & Gaming a. Virtual Service When you want differe nt servers/clients in your LAN to handle different service/Internet application type (e.g. Email, FT P , W eb server etc.) from the Internet, you ca n u se the Virtual Serv er function. Co mputers use numbers called port numbe rs to recognize a particu ...

  • Zonet ZSR1134WE - page 33

    30 b. DMZ The DMZ(Demilitarized Z one) funct ion is to allow one co mputer in LAN t o be exposed to the In ternet for a special-purpose ser vice as Internet gaming or videoconferencing.  Enable DMZ Select the checkbox to enable the DMZ host.  DMZ Host IP Address The IP address of the computer you want to expose. ...

  • Zonet ZSR1134WE - page 34

    31 Security Manag ement T o benefit your further management to the computers in the L AN, you can control some ports access to Internet by data packet filter function. a. Port Filtering  Enable Port Filtering Select the checkbox to enable port filtering  Port Range Enter the port r ange over the protocol for access poli cy .  Protocol Sele ...

  • Zonet ZSR1134WE - page 35

    32 b. IP Filtering  Enable IP Filtering Select the checkbox to enable IP filtering  Local IP Address Enter the IP address you wan t to run t he access policy . c. MAC Filtering ...

  • Zonet ZSR1134WE - page 36

    33  Enable MAC Filtering Select the checkbox to enable MAC filtering  MAC Address Enter the MAC address you want to run the access policy . d. URL Filtering If you want to pre vent computers in local network from ac cessing certain website (like pornogr aphy , violence, o r anything you want to block), you can use thi s function to stop compu ...

  • Zonet ZSR1134WE - page 37

    34 Chapter 7 System tools System Informat ion a. Status The Status page allows you to monitor current status of ZSR1134 WE. ...

  • Zonet ZSR1134WE - page 38

    35 b. Statistics c. System Log  Refresh: Click to update the log.  Clear: Click to clear the current shown log. ...

  • Zonet ZSR1134WE - page 39

    36 DDNS DDNS (Dynamic Domain Name System) is to assign a fix ed host and domain name to a dynamic Internet IP address, which is used to monitor hosting website, FTP server and so on behind ZSR1134WE. If you want t o activate this function, please select Enable and a DDNS service provider to sign up.  Enable DDNS Select the checkbox to enable the ...

  • Zonet ZSR1134WE - page 40

    37 System Manag ement a. Time Zone Setting  Time Zone Select your time zone from the drop-down menu.  N TP Server Manually assign time server address if the defaul t time server does not work. b. Upgrade Firmware ...

  • Zonet ZSR1134WE - page 41

    38  Browse Click to browse the path to the upgraded firmware f iles.  Upload Click to start upgr ade. IMPORTANT: D o not power off the system during the f irmware upg rade to avoid damaging. ZSR11 34WE will reboot automatical ly after th e upgrade. c. Save/Reload Setting  Save Click to back up ZSR1134 WE’ s config urations.  Browse Cl ...

  • Zonet ZSR1134WE - page 42

    39 d. Password Setup  User Nam e Enter a new user name.  N ew Password Enter a new password.  Confirmed Pas sword Re-enter to confirm th e new password. NOTE: It is hig hly recommend ed to change the password to secure your network and ZSR113 4WE. Logout  Click Save Settings to logout ...

  • Zonet ZSR1134WE - page 43

    40 Appendix 1: Troublesh ooting Q1. I cannot access the Web-based Configurat ion Utility from the Ethernet computer used to configure ZSR1134WE.  Check whether the LAN LED is on. If the L ED is not o n, verify the cable for the LAN connection is firmly connected.  Check whether the computer resides on the same subnet with ZSR1134WE’s LAN IP ...

  • Zonet ZSR1134WE - page 44

    41 Q4. I can browse ZSR1134WE’s Web-based Configurat ion Utility but cannot access the Internet.  Check if the WAN LED is ON. If not, verify that the physical connection between ZSR1134WE and the DSL/Cable modem is firmly connected. Also ensure the DSL/Cable modem is working properly.  If WAN LED is ON, open the S ystem Overview page of the ...

Manufacturer Zonet Category Router

Documents that we receive from a manufacturer of a Zonet ZSR1134WE can be divided into several groups. They are, among others:
- Zonet technical drawings
- ZSR1134WE manuals
- Zonet product data sheets
- information booklets
- or energy labels Zonet ZSR1134WE
All of them are important, but the most important information from the point of view of use of the device are in the user manual Zonet ZSR1134WE.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Zonet ZSR1134WE, service manual, brief instructions and user manuals Zonet ZSR1134WE. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Zonet ZSR1134WE.

Similar manuals

A complete manual for the device Zonet ZSR1134WE, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Zonet ZSR1134WE by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Zonet ZSR1134WE.

A complete Zonet manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Zonet ZSR1134WE - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Zonet ZSR1134WE, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Zonet ZSR1134WE, that we can find in the current document
3. Tips how to use the basic functions of the device Zonet ZSR1134WE - which should help us in our first steps of using Zonet ZSR1134WE
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Zonet ZSR1134WE
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Zonet ZSR1134WE in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Zonet ZSR1134WE?

Use the form below

If you did not solve your problem by using a manual Zonet ZSR1134WE, ask a question using the form below. If a user had a similar problem with Zonet ZSR1134WE it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)