English dropdown-ico

Manual Geovision GV-R1352

21 pages Not applicable
Download

Go to site of 21

Summary
  • Geovision GV-R1352 - page 1

    GV-RK1352 and GV-R13 52 Card Reader The GV-RK1352 and GV-R1352 are card r eaders designed to recognize ident ifications cards. GV-RK1352 comes with keypad, allowing it to also recognize PIN codes. Featured w ith the W ie gand and RS-485 outputs, the readers can be connected to any standard access con trol panel. The readers are protected by a weath ...

  • Geovision GV-R1352 - page 2

    1. Physical Descriptions 1.1 E lectric Wire GV-RK1352 Wire C olor Function Red DC 7.5 ~ 12 V Black GND Yellow Beeper Orange G reen LED Light Red Red LED Green W ie gand Data 0 W hi te W ie gand Data 1 Blue RS-485 + Light Blue RS-485 - Rear Vie w GV-R1352 Wire Color Function Red DC 7.5 ~ 12V Black GND Yellow Beeper Orange G reen LED Light Red Red LE ...

  • Geovision GV-R1352 - page 3

    1.2 Key pad (GV-RK1352 Only ) W he n accessing an entry using GV-RK1352, you can enter the door’s PIN code on the keypad or present the card and then enter the card’s PIN code on the keypad to be granted access. The access mod e is defined on GV-ASManager. 1. 0~9 Number Key s: Press the number keys to enter the PI N code . 2. # Key: Press the # ...

  • Geovision GV-R1352 - page 4

    2. Connecting th e Reader to GV-AS Controller You can connect the readers to GV-AS Controllers through Wiegand or RS-485 inter f ace. Note that the connection between the reader and GV-AS Controller varies with diff erent controller models. To see how many readers can be connected to a GV-AS Controller, refer to The Number o f Readers Supported by ...

  • Geovision GV-R1352 - page 5

    2.2 Connecting through RS-485 Interface The following diagrams use GV-RK1352 and GV-A S810 Controll er as an example. Up to eight readers can be connected together to the RS-485 interface on GV-AS810 Contro ller. z Connecting four or less readers to GV-AS810 Controller : Wire C olor Function Black GND Light Blue RS-485 - Blue RS-485 + Red DC 7.5 ~ ...

  • Geovision GV-R1352 - page 6

    2.2.1 Defining Reade rs on GV-AS Controller Web Interface Since multiple r eaders c an connect to GV-AS Controller using one RS-485 interface, you need to specify w hich door each reader controls. This section explains how to define readers on the W eb interface of GV-AS Controller. On the W eb interface, you can also set the reader to read the GID ...

  • Geovision GV-R1352 - page 7

    4. N ext to Read Mode , select Read UID or Read GID to set the conne cted readers to read UID (unique identifier) or GID (G eoVision ID) on GV- AS ID Cards / Key Fobs. If you select Read GID , make sure there are two numbers on your GV-AS ID Cards / Key Fobs as show n below. If ther e is only one number on your GV-AS ID Cards / Key Fobs, GID is not ...

  • Geovision GV-R1352 - page 8

    3. Installing the GV-R/RK/DFR Config A P Th master / slave status, and whether it reads UID or GID. W hen using the Con f ig AP, the reader needs to be connected to a PC through GV-COM, GV-Hub or GV-NET/IO Car d V3.1. e GV-R/RK/DFR Config AP allows you to set the reader’s beeper / LED, ID number, You can inst fig AP from the Software DVD or GeoVi ...

  • Geovision GV-R1352 - page 9

    4. Overlaying Card Numb ers on GV-System Li v e Vie w You can overlay card numbers recogniz ed at the reader onto a camera ch annel on GV- System. To overlay card numbers on GV-System channel, the reader needs to be c onnected to a GV-Sy stem th rou gh GV-C OM , GV-Hub or G V-NET /IO Ca rd V3. 1. RS-4 85 GV-HUB / GV-COM / GV-NET/IO Card RS-2 32 GV- ...

  • Geovision GV-R1352 - page 10

    2. Select the COM port that is connected to the reader and click Op en C OM . The seria number and firmware version of the reader will be automatically detected. The red s next to 3. Under l quare the COM port box should change to blue to indicate the COM port is correct. M aster / Slave , set the reader to Slave . If you want to connect multiple r ...

  • Geovision GV-R1352 - page 11

    4.2 A dding the Reader to GV-Sy stem 1. In GV -System , cli ck the Configure button, select A ccessories , and select GV Wiegand Capture Device Setting . This dialog box appears. 2. Click the New butt on. This dialog box appear s.  Type: Select GV-W ie gand Capture. February 6, 2015 11  Device: Type a number and name to help y ou identify the ...

  • Geovision GV-R1352 - page 12

    5. Changing t he Default Se ttings of Bee per and LED You can change the defa ult sett ings of the LED and the beeper by enabling a GV-AS210 / d LED, green LED or beeper when the specified alarm events occur. For GV -AS400, built-in LED and beeper settings are available on the W eb interface for outputs 9 ~ 16. The GV-AS Controller and the reader n ...

  • Geovision GV-R1352 - page 13

    2. Click Open COM . The serial number and the firmware version of the reader will be automatically detected. 3. T o enable external control o f Beeper or LED, sel ect Beeper , Green LED or Red LED . 4. Select Master from the M aster / Slave drop-down list. ID number set on the Extended Reader page of the GV-AS Controller Web interface. 6. Click Set ...

  • Geovision GV-R1352 - page 14

    5.2 Wiring the Beeper and LED to the GV-A S Controller To wire the beeper and L ED to GV-AS210 / 2110 / 400 / 410 / 4110 / 810 / 8110, connect the control wires of the reader’s Beeper, Red LED or Green LED to any of the outputs on GV-AS Controller. Not e that outputs 9 ~ 16 on GV-AS400 are used for the built-in LED and beeper settin gs. Wiring LE ...

  • Geovision GV-R1352 - page 15

    After wiring, you also need to go to GV-ASManager to select the alarm conditions that will set the device list, off the reader’s beeper. In GV-ASManager, right-click the GV-AS Controller in click Settings , and click the Door / Gate tab to select the alarm condi tions. February 6, 2015 15 ...

  • Geovision GV-R1352 - page 16

    5.3 Configuring the Beeper and LED Settings for Eac h Door/Gate After connecting the wires for beeper o r LED, specify the conditions to trigger the beeper and LED on the GV-AS210 / 2110 / 400 / 410 / 4110 / 810 / 8110 Web interface. 1. O n the controller W eb interface, click Output Setting . The page below appears. 2. Find the output wired to the ...

  • Geovision GV-R1352 - page 17

    6. Setting UID or GID on GV-R/RK/DFR Config A P By default, the readers read the UID (unique identi f ier) on ID cards or key fobs. Using GV- R/RK/DFR Config AP, you can set the GV-RK1352 / GV-R1352 to read GID (GeoVision ID) n GV-AS ID Cards / Key Fobs instead. o Note: 1. To see how to install the Config AP and how to identify the COM port of the ...

  • Geovision GV-R1352 - page 18

    To use GID, make sure there a re two numbers on your GV-AS ID Cards / Key Fobs as shown below. If there is only one number on your GV-AS ID Cards / Key Fobs, GID is no t supported and you must select Unique Identification ( UID). February 6, 2015 18 ...

  • Geovision GV-R1352 - page 19

    7. Firmw are Upgrade included in the Software CD. Important Note s before You Start Before you start updating the firmware, please read these important notes: 1. W hile the firmware is being updated, the power supply must not be interrupted. 2. Do not turn the power off within 10 minutes after the firmware is updated. GeoVision will periodically re ...

  • Geovision GV-R1352 - page 20

    8. Specification s GV-RK1352 GV-R1352 CPU 8-bit microprocesso r Frequency 13.56 M Mifare C Hz for ISO14443A (Mifare DESFire, Mifare Plus and lass) Wiegand Interface W ie gand 26 / 34 bits, distance 30 m / 98.43 ft RS-485 9,600 bps, connect up to 8 GV-RK1352 / R1352 units Power DC 7.5 ~ 12V LED Red, Green and Blue LED Beeper Buzzer Reader Color Blac ...

  • Geovision GV-R1352 - page 21

    February 6, 2015 21 RK1352 Onl y) O tional accessories can ex p bilities and versatilit V-RK1352 Card Reader. Consult your sales r information. 9. Accessor y (GV- p and the capa ies of your G epresentative for more GV -MountA 900 • Dim GV-Moun 2 to a US s er box. ens • Weight: tA900 is a mounting plate that allows you to attach GV-RK135 ingle g ...

Manufacturer Geovision Category Security access control system

Documents that we receive from a manufacturer of a Geovision GV-R1352 can be divided into several groups. They are, among others:
- Geovision technical drawings
- GV-R1352 manuals
- Geovision product data sheets
- information booklets
- or energy labels Geovision GV-R1352
All of them are important, but the most important information from the point of view of use of the device are in the user manual Geovision GV-R1352.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Geovision GV-R1352, service manual, brief instructions and user manuals Geovision GV-R1352. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Geovision GV-R1352.

Similar manuals

A complete manual for the device Geovision GV-R1352, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Geovision GV-R1352 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Geovision GV-R1352.

A complete Geovision manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Geovision GV-R1352 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Geovision GV-R1352, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Geovision GV-R1352, that we can find in the current document
3. Tips how to use the basic functions of the device Geovision GV-R1352 - which should help us in our first steps of using Geovision GV-R1352
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Geovision GV-R1352
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Geovision GV-R1352 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Geovision GV-R1352?

Use the form below

If you did not solve your problem by using a manual Geovision GV-R1352, ask a question using the form below. If a user had a similar problem with Geovision GV-R1352 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)