English dropdown-ico

Manual Hotpoint HDA400

20 pages 0.53 mb
Download

Go to site of 20

Summary
  • Hotpoint HDA400 - page 1

    ‘owtogetYour the best from Dkhwmher Contents Air Gap 11 Cycle Selection 5 Appliance Registration 2 Drying Options 4,5 Care and Cleaning 11 Problem Solver 13–15 China, Crystal, Sterling 10 Rinse Agent 6 Consumer Services 19 Safety Instructions 3 Cycle Features 4,5 User Maintenance Instructions 11 Detergent, Detergent Guide 7 Warranty Back Cover ...

  • Hotpoint HDA400 - page 2

    ~LP US ~LP YOU... Before using your If you received Write down the model dishwasher, read this a damaged dishwasher... and serial numbers. guide carefully. Immediately contact the dealer You’ll find them on a label It is intended to help you (or builder) that sold you the fastened to the tub wall just operate and maintain your new dishwasher. ins ...

  • Hotpoint HDA400 - page 3

    A WARNING—When using this appliance, always exercise basic safety precautions, including the following: ● Use this appliance only for iti intended purpose, as you will find described in this Use and Care Guide. o ● This dishwasher must be properly ‘Q-$”: b installed and located in accordance ~ + . . . with the Installation Instructions .- ...

  • Hotpoint HDA400 - page 4

    u HOW TO OPERATE YOUR DIS~ASHER NOTE: If dishwasher drains into a food waste disposal, operate the disposal until it is empty before starting dishwasher. Step 1. Load your dishwasher. (See Loading section.) Step 2. Make sure the Cycle Indicator Dial is at the OFF position and the door is unlatched. Add detergent to the detergent dispenser. (See Det ...

  • Hotpoint HDA400 - page 5

    1 ● & RINSE & HOLO (MUEOOWOFO Dial Cycles The RINSE & HOLD cycle is for rinsing partial loads which will be washed later. Do not use detergent. a. Mtie sure HEATED DRY is off. b. Be sure the door is unlatched. c. Slowly turn the Cycle Indicator Dial to RINSE & HOLD. d. Latch the door to start the cycle. The PLATE WARMER cycle is f ...

  • Hotpoint HDA400 - page 6

    Good Dishwashing Starts with HOT Water To get dishes clean and dry, you need hot water. For good washing and drying, the entering water must beat least 120°F. To prevent dish damage, inlet water shodd not exceed 150°F. How to Test Water Temperature Check your water temperature with a candy or meat Helpful hints: If outside temperatures are unusua ...

  • Hotpoint HDA400 - page 7

    How to Choose and Use the Wght Detergent Use ordy powder or liquid detergent specifically made for use in dishwashers. Other types wi~ wuse oversudsing. How much detergent should you use? That depends. Is your water “hard” or “soft”? With hard water, you need extra detergent to get dishes clean. With soft water, you need less detergent. You ...

  • Hotpoint HDA400 - page 8

    HOW TO LOAD YOUR DIS~AS~R This is a random mixed load, the most common type you will have. Make sure dishes are properly loaded to insure that water can reach the soiled surfaces. The wash arm in the bottom sprays water up. The tower that rises in the center sends water out over the dishes to wash the items in the upper rack. WATCH OUT FOR THIS. Th ...

  • Hotpoint HDA400 - page 9

    HOW TO LOAD T~ BOTTOM WCK ‘-%.. , ., Pots, pans, casseroles, salad bowls, mixing bowls and lids must be loaded in the bottom rack, facing down. ,, ,, ’,,, /. Fit plates and saucers between the pins. Place items so that water and detergent from wash arm can reach soiled surfaces. Load platters, pots, pans and bowls along the sides, in corners or ...

  • Hotpoint HDA400 - page 10

    WHAT YOU CAN USUALLY WASH SAFELY ~ YOUR DIS~ASHER I Usually Material Safe Aluminum I YES Chirtti YES Stoneware Crystal YES Non-dishwasher NO items—such as electronic air cleaner filters, furnace filters, paint brushes, etc. Glass I YES tron NO Pewter NO I Plastics YES Stainless steel YES Sterling silver YES and silver plate Non-stick YES coatings ...

  • Hotpoint HDA400 - page 11

    USER MAINTENANCE INSTRUCTIONS Clean the control panel with a lightly dampened Appliance Polish Wa & Cleaner (Cat. No. cloth. Dry thoroughly. Do not use abrasives or WR97X0216) is available from GE Service and sharp objects on the panel. They can damage it. Parts Centers. Clean the outside with a good appliance polish The inside usually takes ca ...

  • Hotpoint HDA400 - page 12

    HOW TO CHANGE COLOR PANELS If you are redecorating, you can change your dishwasher’s front panel to match or blend with your new colors by flipping it over. Each side of each panel is a different color. You may also paint a panel with a color of your own choice. How to Change the Door Panel: 1. Take out trim screws on either side of the dishwashe ...

  • Hotpoint HDA400 - page 13

    PROBLEM DISHWASHER WON’T RUN UNUSUAL NOISE DISHES DON’T DRY UNCLEAN DISHES AND FLATWARE DETERGENT LEFT IN DISPENSER CUPS DETERGENT CUP LID WON’T LATCH A~ER ADDING DETERGENT YELLOW OR BROWN ~M QUESTIONS? USE THIS PROBLEM SOLVER [ ● ● POSSIBLE CAUSE A fuse in your home maybe blown, or the circuit breaker tripped. Replace fuse or reset circu ...

  • Hotpoint HDA400 - page 14

    THE PROBLEM SOL~R (continued) PROBLEM SPOTS AND ~M~G ON GLASSES AND ~ATWAW CLOUDINESS ON GLASSWAW CHIPPING OF CHWA POSSIBLE CAUSE Spotting can be caused by dl these things: ● Extremely hard water. (See How to Choose and Use Detergent section.) ● Low inlet water temperature. (See How to Test Water Temperature section.) ● Overloading the dishwa ...

  • Hotpoint HDA400 - page 15

    PROBLEM BLACK OR GRAY MARKS ON DISHES SMALL AMOUNT OF WATER STANDING IN THE BOTTOM OF THE TUB WA~R WON’T PUMP OUT OF THE TUB SUDS IN THE TUB DISHWASHER LEAKS MOTOR HUMS STAINING OF TUB INTERIOR SOUNDS YOU WILL HEAR VAPOR AT THE VENT POSSIBLE CAUSE Aluminum utensils often leave marks when they rub against dishes. Remove marks with a mild abrasive ...

  • Hotpoint HDA400 - page 16

    NOTES 16 ...

  • Hotpoint HDA400 - page 17

    NOTES 17 ...

  • Hotpoint HDA400 - page 18

    NOTES 18 ...

  • Hotpoint HDA400 - page 19

    We’ll Be There With the purchase of your new Hotpoint appliance, receive the assurance that ifyou ever need information or assistance, wdll be there. All you have to do is call—toll-free! lwHome Repair Service 80MEXARES(80M32-2737) Our consumer service professional will provide expert repair service on your Hotpoint appliance, scheduled at a ti ...

  • Hotpoint HDA400 - page 20

    YOUR HOTPOINT Staple sales slip or cancelled check AUTOMATIC DISHWASHER here. Proof of original purchase date I WARRANTY is needed to obtain service under warranty. WHAT IS COVERED FULL ONE-YEAR WARRANTY For one year from date of original purchase, we will provide, free of charge, parts and service labor in your home to repair or replace any pan of ...

Manufacturer Hotpoint Category Dishwasher

Documents that we receive from a manufacturer of a Hotpoint HDA400 can be divided into several groups. They are, among others:
- Hotpoint technical drawings
- HDA400 manuals
- Hotpoint product data sheets
- information booklets
- or energy labels Hotpoint HDA400
All of them are important, but the most important information from the point of view of use of the device are in the user manual Hotpoint HDA400.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Hotpoint HDA400, service manual, brief instructions and user manuals Hotpoint HDA400. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Hotpoint HDA400.

Similar manuals

A complete manual for the device Hotpoint HDA400, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Hotpoint HDA400 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Hotpoint HDA400.

A complete Hotpoint manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Hotpoint HDA400 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Hotpoint HDA400, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Hotpoint HDA400, that we can find in the current document
3. Tips how to use the basic functions of the device Hotpoint HDA400 - which should help us in our first steps of using Hotpoint HDA400
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Hotpoint HDA400
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Hotpoint HDA400 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Hotpoint HDA400?

Use the form below

If you did not solve your problem by using a manual Hotpoint HDA400, ask a question using the form below. If a user had a similar problem with Hotpoint HDA400 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)