English dropdown-ico

Manual Echo GT-2000EZR

27 pages 1.28 mb
Download

Go to site of 27

Summary
  • Echo GT-2000EZR - page 1

    Grass T rimmer Operator's Manual MODEL GT-2000EZR Serial Number 03001001 - 03999999 W ARNING DANGER Read rules for safe operation and instructions carefully. ECHO provides an Operator's Manual and a Safety Manual. Both must be read and understood for proper and safe operation. X770000370 01/02 X7702273900 ...

  • Echo GT-2000EZR - page 2

    ...

  • Echo GT-2000EZR - page 3

    G RASS T RIMMER O PERA TOR ' S M ANUAL 3 M ANUAL S AFETY S YMBOLS AND I MPORT ANT I NFORMA TION This symbol accompanied by the words WARNING and DANGER calls attention to an act or condition that can lead to serious personal injury to operator and bystanders. IMPORTANT The enclosed message provides information necessary for the protection of t ...

  • Echo GT-2000EZR - page 4

    4 WEAR HAND AND FOOT PROTECTION KEEP BYSTANDERS AND HELPERS AWAY 15 M (50 FT.). DO NOT USE BLADES. STRING LINE ONLY DO NOT EXCEED 10,000 RPM. DO NOT OPERATE WITHOUT GUARDS AND SHIELDS IN PLACE. BEWARE - THROWN, RICOCHET OBJECTS SYMBOL DESCRIPTION/APPLICATION SYMBOL FORM/ SHAPE SYMBOL DESCRIPTION/APPLICATION SYMBOL FORM/ SHAPE HOT SURFACE CARBURETOR ...

  • Echo GT-2000EZR - page 5

    G RASS T RIMMER O PERA TOR ' S M ANUAL 5 EQUIPMENT W ARNING DANGER Use only ECHO approved attachments. Serious injury may result from the use of a non approved attachment combi- nation. ECHO, INC. will not be responsible for the failure of cutting devices, attachments or accessories which have not been tested and approved by ECHO. Read and com ...

  • Echo GT-2000EZR - page 6

    6 D ESCRIPTION The ECHO product you purchased has been factory pre-assembled for your convenience. Due to packaging restrictions, shield installation and positioning of the front handle are necessary. After opening the carton, check for damage. Immediately notify your retailer or ECHO Dealer of damaged or missing parts. Use the contents list to che ...

  • Echo GT-2000EZR - page 7

    G RASS T RIMMER O PERA TOR ' S M ANUAL 7 CONTENT LIST _____ 1 - Trimmer Assembly _____ - Power Head _____ - Drive Shaft Assembly _____ 1 - Plastic Bag (Co-Pack) _____ - Operator's Manual _____ - Safety Manual _____ - Shield Assembly _____ 1 - Nylon Trimmer Head _____ - 12, 8 in. x .080 Pre-cut Nylon Line _____ - Hardware Bag _____ - 1, Lo ...

  • Echo GT-2000EZR - page 8

    8 1. POWER HEAD - Factory Assembled to the Drive shaft assembly. Includes the Engine, Clutch, Fuel System, Ignition System and Recoil Starter. 2. GRIP - Rear (right hand) handle. 3. FRONT HANDLE - The Front (loop) handle is factory assembled to the Drive Shaft assembly but must be re- positioned for proper cutting attitude and operator comfort. 4. ...

  • Echo GT-2000EZR - page 9

    G RASS T RIMMER O PERA TOR ' S M ANUAL 9 S PECIFICA TIONS L E D O M R Z E 0 0 0 2 - T G h t g n e L ) . n i 3 . 5 5 ( m m 5 0 4 1 h t d i W ) . n i 4 . 2 1 ( m m 5 1 3 t h g i e H ) . n i 2 . 4 1 ( m m 0 6 3 d a e H r e t t u C / w ) y r d ( t h g i e W ) . b l 0 . 0 1 ( g k 5 5 . 4 e p y T e n i g n E e n i g n e e n i l o s a g r e d n i l y ...

  • Echo GT-2000EZR - page 10

    10 A SSEMBL Y PLASTIC SHIELD Tools Required: None 1 . Remove wing nut (C), washer (B), and bolt (A). 2 . Snap the shield over the bearing housing. 3 . Install bolt (A), washer (B) and wing nut (C). NYLON LINE HEAD Tools Required: Head Locking Tool, 9/16 in. Socket Parts Required: Rapid Loader TM Head. 1 . Remove plastic threaded shaft sleeve from P ...

  • Echo GT-2000EZR - page 11

    G RASS T RIMMER O PERA TOR ' S M ANUAL 11 FRONT ( LOOP ) HANDLE NOTE Front handle is pre-installed. Re-positioning and tightening is all that is required. 1 . Position front handle (E) in comfortable operating position and tighten wing nut (F). The cutting attachment should be 5cm- 7.5cm (2 in. -3 in.) above the ground and as level as possible ...

  • Echo GT-2000EZR - page 12

    12 IMPORTANT Spilled fuel is a leading cause of hydrocarbon emissions. Some states may require the use of automatic fuel shut-off containers to reduce fuel spillage. Contact your ECHO dealer for ordering information. After refueling • Wipe any spilled fuel from the unit. • Move at least 3 m (10 ft.) from refueling location before starting the e ...

  • Echo GT-2000EZR - page 13

    G RASS T RIMMER O PERA TOR ' S M ANUAL 13 O PERA TION ST ARTING COLD ENGINE W ARNING DANGER • Never leave the ignition switch in the on position while the unit is unattended. • Never allow partial tension to remain in the starter, otherwise serious personal injury may result. W ARNING DANGER Never attempt to disassemble this recoil starter ...

  • Echo GT-2000EZR - page 14

    14 4. Recoil Starter Lay the unit on a flat clear area. Firmly grasp throttle grip with left hand and fully depress throttle trigger to wide open position. Gently pull recoil starter handle/rope (D) until engine fires or 2 to 3 engine engagements. 5. Choke After engine fires or 2 to 3 engine engagements, move choke lever to “Run” position. Hold ...

  • Echo GT-2000EZR - page 15

    G RASS T RIMMER O PERA TOR ' S M ANUAL 15 STOPPING ENGINE 1. Throttle Release throttle and allow engine to return to idle before shutting engine off. 2. Stop Switch Move stop switch button (A) to STOP position. W ARNING DANGER If engine does not stop when stop switch is moved to STOP position, close choke - COLD START position - to stall engin ...

  • Echo GT-2000EZR - page 16

    16 MAINTENANCE INTERV ALS m e t s y S / t n e n o p m o Ce r u d e c o r P e c n a n e t n i a M r o y l i a D e r o f e B e s U y r e v E l e u f e R s h t n o M 3 0 9 r o s r u o H s h t n o M 6 0 7 2 r o s r u o H y l r a e Y r e t l i F r i Ae c a l p e R / t c e p s n I C / I* R r e n i a r t S l e u Fe c a l p e R / t c e p s n I IR e n i L l ...

  • Echo GT-2000EZR - page 17

    G RASS T RIMMER O PERA TOR ' S M ANUAL 17 AIR FIL TER Level 1. Tools required: Cleaning brush, 25 or 50 mm (1 or 2 in.) medium bristle paint brush. Parts required: 90008 REPOWER TM AIR & FUEL FILTER KIT. 1. Close choke (Cold Start Position). This prevents dirt from entering the carburetor throat when the air filter is removed. Brush accumu ...

  • Echo GT-2000EZR - page 18

    18 SP ARK PLUG Level 2. Tools Required: Spark Plug socket wrench and screw driver, Feeler gauge. Preferably a wire gauge. Parts Required: 90064 REPOWER TM Tune-Up Kit 1 . Remove spark plug and check for fouling, worn and rounded center electrode. 2 . Clean the plug or replace with a new one. DO NOT sand blast to clean. Remaining sand will damage en ...

  • Echo GT-2000EZR - page 19

    G RASS T RIMMER O PERA TOR ' S M ANUAL 19 A B C D 1 . Remove spark plug lead and throttle linkage end from the carbure- tor swivel. 2 . Remove the four screws that retain the cover. Two at the top of the Recoil Starter, two on either side of the front. Lift the cover from the engine and lay to the front of the trimmer. NOTE The throttle linkag ...

  • Echo GT-2000EZR - page 20

    20 CARBURETOR ADJUSTMENT Engine Break-In New engines must be operated a minimum duration of two tanks of fuel break-in before carburetor adjustments can be made. During the break-in period your engine performance will increase and exhaust emissions will stabilize. Idle speed can be adjusted as required. High Altitude Adjustment High altitude adjust ...

  • Echo GT-2000EZR - page 21

    G RASS T RIMMER O PERA TOR ' S M ANUAL 21 LUBRICA TION Level 1. Tools Required: 8mm Open End Wrench, Screwdriver, Clean Rag. Parts Required: ECHO ® LUBE TM 8 oz. (P/N 91014) or Lithium Base Grease. 1 . Remove plastic shield. 2 . Loosen bearing housing locating screw (A), at the top of the housing, loosen mounting screw (B) and remove gear cas ...

  • Echo GT-2000EZR - page 22

    22 T ROUBLESHOOTING W ARNING DANGER Fuel vapors are extremely flammable and may cause fire and/or explosion. Never test for ignition spark near an open spark plug opening, otherwise serious personal injury may result. T R A H C G N I T O O H S E L B U O R T M E L B O R P E N I G N E m e l b o r Pk c e h Cs u t a t Se s u a Cy d e m e R e n i g n E ...

  • Echo GT-2000EZR - page 23

    G RASS T RIMMER O PERA TOR ' S M ANUAL 23 2 . Place the stop switch (A) in the "OFF" position. 3 . Remove accumulation of grease, oil, dirt and debris from exterior of unit. 4 . Perform all periodic lubrication and services that are required. 5 . Tighten all the screws and nuts. 6. Drain the fuel tank completely and pull the recoil s ...

  • Echo GT-2000EZR - page 24

    ECHO, INCORPORA TED 400 O AKWOOD R OAD L AKE Z URICH , IL 60047-1564 www .echo-usa.com DEALER? Call 1-800-432-ECHO or www .echo-usa.com CONSUMER PRODUCT SUPPORT 1-800-673-1558 8:30 - 4:30 Mon - Fri C.S.T. S ER VICING I NFORMA TION P ARTS Genuine ECHO Parts and ECHO REPOWER™ Parts and Assemblies for your ECHO products are available only from an Au ...

  • Echo GT-2000EZR - page 25

    A 1 D ESCRIPTION Page 7 CONTENTS ____ 1 - Trimmer Assembly ____ - Power Head ____ - Drive Shaft Assembly ____ 1 - Plastic Bag (Co-Pack) ____ - Rapid Loader 2-line Head ____ - Operator's Manual 99922203524 12/01 SUP22203524 SUPPLEMENT TO OPERA TOR'S MANUAL P ART NUMBER X7702273900 (X770000370) FOR MODEL: GT-2000EZR S/N 03001001 & UP Pl ...

  • Echo GT-2000EZR - page 26

    99922203562 04/02 SUP22203562 SUPPLEMENT TO OPERA TOR'S MANUAL FOR MODELS: GT-201EZR S/N 02001001- 02999999 P ART NUMBER X7702274001 (X770000381) FOR MODELS: GT-2000EZR S/N 03001001- 03999999 P ART NUMBER X7702273900 (X770000370) M AINTENANCE - P AGE 18 COOLING SYSTEMS CLEANING 1 . Remove one (1) screw (A) from Top Guard and remove guard. 2 . ...

  • Echo GT-2000EZR - page 27

    A B 2 C D 9 . Lift the cover from the engine and lay to the front of the trimmer. NOTE The throttle linkage remains assembled to the cover. 1 0 . Reinstall spark plug to prevent dirt and debris from entering engine. 1 1 . Use a brush to remove dirt from the cylinder fins. IMPORTANT DO NOT use a metal scraper to remove dirt from the cylinder fins. 1 ...

Manufacturer Echo Category Trimmer

Documents that we receive from a manufacturer of a Echo GT-2000EZR can be divided into several groups. They are, among others:
- Echo technical drawings
- GT-2000EZR manuals
- Echo product data sheets
- information booklets
- or energy labels Echo GT-2000EZR
All of them are important, but the most important information from the point of view of use of the device are in the user manual Echo GT-2000EZR.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Echo GT-2000EZR, service manual, brief instructions and user manuals Echo GT-2000EZR. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Echo GT-2000EZR.

Similar manuals

A complete manual for the device Echo GT-2000EZR, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Echo GT-2000EZR by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Echo GT-2000EZR.

A complete Echo manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Echo GT-2000EZR - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Echo GT-2000EZR, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Echo GT-2000EZR, that we can find in the current document
3. Tips how to use the basic functions of the device Echo GT-2000EZR - which should help us in our first steps of using Echo GT-2000EZR
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Echo GT-2000EZR
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Echo GT-2000EZR in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Echo GT-2000EZR?

Use the form below

If you did not solve your problem by using a manual Echo GT-2000EZR, ask a question using the form below. If a user had a similar problem with Echo GT-2000EZR it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)