English dropdown-ico

Manual Sioux Tools 5000A

20 pages 0.29 mb
Download

Go to site of 20

Summary
  • Sioux Tools 5000A - page 1

    Page No 1 Safety rules when using 5000A/5000AL/5000AP Imp act Wrenches – Use only impact sockets and extensions, universal joint s, etc. rated as being suitable for use with impact wrenches. – Prolonged exposure to vibration may cause injury . – Read all instructions before using this tool. All operators must be fully trained in its use and a ...

  • Sioux Tools 5000A - page 2

    Page No 2 – T ake care against entanglement of the moving parts of the tool with clothing, hair , ties, cleaning rags, rings, jewelry , watches, bracelets, etc. This could cause the body or part s of the body to be drawn towards and in contact with the moving parts of the tool and could be very dangerous. – It is expected that users will adopt ...

  • Sioux Tools 5000A - page 3

    Page No 3 Printed in T aiwan Dismantling & Assembly Instructions Disconnect tool from air supply . Unscrew hammer case cap screws (38) and take of f hammer case (36). T ake out hammer case pilot (35) and anvil (39, 39B or 39C) from hammer case (36). Release hammer (34) by removing hammer pin (33), then take off hammer frame rear washer (19) and ...

  • Sioux Tools 5000A - page 4

    Page No 4 Règles de sécurité pour l’emploi des clés à chocs 5000A/5000AL/5000AP • Employez seulement des douilles, rallonges, cardans, etc. pour clé à choc qui réspondent aux conditions nominales de fonctionnement de la clé à chocs. • Une exposition prolongée aux vibrations peut causer des blessures. • Lisez les instructions avan ...

  • Sioux Tools 5000A - page 5

    Page No 5 St ations de travail Cet outil est destiné à un usage manuel seulement. On recommande d’employer l’outil en position debout et sur un sol ferme. On peut l’employer dans d’autres positions mais avant un tel usage, l’opérateur doit se trouver dans une position stable, avoir l’outil bien en main, et être conscient que l’out ...

  • Sioux Tools 5000A - page 6

    Page No 6 Impremé au T aiwan Instructions de démontage et de mont age Déconnectez l’outil de l’arrivée d’air . Dévissez les vis de fixation du carter de marteau (38) et retirez le carter de marteau (36). Retirez le pilote de carter de marteau (35) et l’enclume (39, 39B ou 39C) du carter de marteau (36). Libérer le marteau (34) en enle ...

  • Sioux Tools 5000A - page 7

    Page No 7 Vibrationspegel: 13 m/Sek. Testverfahren: Getestet nach der ISO-Norm 8662 Teile 1 & 7 Lärmpegel: Lärmdruckpegel 97,0 dB (A) Lärmleistungspegel 108,0 dB (A) Testverfahren: Getestet nach dem Pneurop- Testcode PN8NTC1 und der ISO-Norm Nr. 3744 Verwendung einer Ausgleichs – bzw. Stützvorrichtung empfohlen: NEIN Nettogewicht des Prod ...

  • Sioux Tools 5000A - page 8

    Page No 8 V orgesehener Einsatzbereich des Werkzeugs – 5000A/5000AL/5000AP Der Schlagschrauber ist zum Festziehen und Lösen von V erbindungselementen mit Gewinden innerhalb des vom Hersteller genannten Einsatzbereichs gedacht. Er darf nur mit geeigneten12,7 mm Innenvierkantaufsätzen für Einschlagmuttern verwendet werden. Es dürfen nur für Dr ...

  • Sioux Tools 5000A - page 9

    Page No 9 Gedruckt in T aiwan Anleitungen zum Auseinander- und Zusammenbau Das Werkzeug von der Luftzufuhr abtrennen. Die Kopfschrauben (38) des Hammergehäuses abschrauben, und das Hammergehäuse (36) abnehmen. Den Führungsring (35) und den Amboss (39, 39B oder 39C) des Hammergehäuses vom Hammergehäuse (36) abnehmen. Den Hammer (34) durch Entfe ...

  • Sioux Tools 5000A - page 10

    Page No 10 Nivel de vibración: 13 metros/seg 2 Método de prueba: Prueba efectuada de acuerdo con las normas ISO 8662, partes 1 & 7 Nivel de ruido: Nivel de presión de sonido 97,0 dB (A) Nivel de potencia de sonido 108,0 dB (A) Método de prueba: Prueba efectuada de acuerdo con el código de pruebas Pneurop PN8NTC1 y la norma ISO 3744. Uso re ...

  • Sioux Tools 5000A - page 11

    Page No 11 Uso anticip ado de la herramient a – 5000A/5000AL/5000AP La llave de impacto ha sido diseñada para apretar y aflojar los fijadores de rosca dentro de la gama especificada por el fabricante. La herramienta se debe usar solamente con casquillos hembra apropiados de 12,7 mm, de tipo de impacto, para enroscar tuercas. Sólo use casquillos ...

  • Sioux Tools 5000A - page 12

    Page No 12 Impreso en T aiwan Instrucciones para mont ar y desmont ar la herramient a Desconecte la herramienta del suministro de aire. Destornille los tornillos de cabeza (38) de la caja del martillo y saque la caja del martillo (36) hacia fuera. Retire el piloto de la caja del martillo (35) y el yunque (39, 39B y 39C) fuera de la caja del martill ...

  • Sioux Tools 5000A - page 13

    Page No 13 Trillingsnivo: 13 m/s Test methode: getest in overeenstemming met ISO 8662, gedeelte 1 & 7 Geluidsnivo: Geluidsdruk niveau 97,0 dB (A) Geluidskracht niveau 108,0 dB (A) Test methode: Getest in overeenstemming met de Pneurop test code PN8NTC1 en ISO standaard 3744. Aanbevolen gebruik van balanceerder of onder- steuning NEE Product net ...

  • Sioux Tools 5000A - page 14

    Page No 14 T e verwachten gebruik van het gereedschap – 5000A/5000AL/5000AP De slagmoersleutel is alleen ontworpen voor het aandraaien en losdraaien van met schroefdraad voorziene bevestigingsmiddelen, binnen het door de fabrikant gespecificeerde bereik. Het mag alleen gebruikt worden met het geschikte type 1/2" (12,7mm) vierkante slagdoppen ...

  • Sioux Tools 5000A - page 15

    Page No 15 Gedrukt in T aiwan Demont age en Mont age Instructies Maak het gereedschap los van de luchttoevoer . Schroef de moerbouten (38) van de hamerbehuizing los en haal de hamerbehuizing (36) eraf. Haal de geleiding (35) en het aambeeld (39, 39B of 39C) uit de hamerbehuizing (36). Maak de hamer (34) los door de hamerpen (33) te verwijderen. V e ...

  • Sioux Tools 5000A - page 16

    Page No 16 Livello di vibrazioni 13 m/sec 2 Metodo di collaudo: Collaudato secondo gli standard ISO 8662, parti 1 e 7 Rumorosità: Pressione acustica 97,0 dB (A) Potenza acustica 108,0 dB (A) Metodo di collaudo: Collaudato secondo la normativa di collaudo Pneurop PN8NTC1 e Standard ISO 3744. Si raccomanda l’uso di bilanciatore o supporto NO Peso ...

  • Sioux Tools 5000A - page 17

    Page No 17 Post azioni di lavoro L ’utensile deve essere usato solo come strumento a mano. Si raccomanda di usare l’utensile stando in piedi su un piano solido. Può essere usato in altre posizioni, ma prima di tale uso, l’operatore deve porsi in posizione sicura, con una presa ed un appoggio solidi ed essere consapevole che, mentre si allent ...

  • Sioux Tools 5000A - page 18

    Page No 18 S tampato in T aiwan Istruzioni per mont aggio e smont aggio Scollegare l’utensile dal sistema di alimentazione dell’aria. Svitare le viti (38) sulla calotta dell’alloggiamento del meccanismo di percussione (36). Estrarre la guida (35) dell’alloggiamento del meccanismo di percussione e l’incudine (39, 39B e 39C) dall’alloggia ...

  • Sioux Tools 5000A - page 19

    Page No 19 5000A 1/2" Pistol Grip T win Hammer Impact W rench 5000AL Model 5000A with 2" Extended Anvil 5000AP Model 5000A with Pin Anvil Ref. No. Part No. Description Ref. No. Description Part No. 25 505822A Cylinder Dowel 26 505823A Hammer Case Bushing 27 505824A Rotor Blade (6 pc. set) 28 505825A Front End Plate 29 505826A Rear End Pla ...

  • Sioux Tools 5000A - page 20

    Page No 20 ...

Manufacturer Sioux Tools Category Impact Driver

Documents that we receive from a manufacturer of a Sioux Tools 5000A can be divided into several groups. They are, among others:
- Sioux Tools technical drawings
- 5000A manuals
- Sioux Tools product data sheets
- information booklets
- or energy labels Sioux Tools 5000A
All of them are important, but the most important information from the point of view of use of the device are in the user manual Sioux Tools 5000A.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Sioux Tools 5000A, service manual, brief instructions and user manuals Sioux Tools 5000A. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Sioux Tools 5000A.

Similar manuals

A complete manual for the device Sioux Tools 5000A, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Sioux Tools 5000A by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Sioux Tools 5000A.

A complete Sioux Tools manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Sioux Tools 5000A - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Sioux Tools 5000A, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Sioux Tools 5000A, that we can find in the current document
3. Tips how to use the basic functions of the device Sioux Tools 5000A - which should help us in our first steps of using Sioux Tools 5000A
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Sioux Tools 5000A
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Sioux Tools 5000A in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Sioux Tools 5000A?

Use the form below

If you did not solve your problem by using a manual Sioux Tools 5000A, ask a question using the form below. If a user had a similar problem with Sioux Tools 5000A it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)