English dropdown-ico

Manual Ringdale IP Router

12 pages 0.09 mb
Download

Go to site of 12

Summary
  • Ringdale IP Router - page 1

    1 Contents Introduction 2 Installation 3 Using PeripheralVision ® to Configure the IP Router 5 IP Router Page 5 Passwords 6 Routing T able Page 7 Broadcast Forward Page 8 PeripheralVision ® Licensing 9 Safety and Location Advice 1 0 Troubleshooting and Technical Reference 1 1 Technical Support 1 2 ...

  • Ringdale IP Router - page 2

    2 Introduction The Ringdale IP Router is a local two port Ethernet IP router which enables IP packets to be routed from one Network/Subnet to another on your Local or Wide Area Network, and even across the Internet if required. The IP Router is simple to install and can be configured and remotely managed using the PeripheralVision ® software provi ...

  • Ringdale IP Router - page 3

    3 Installation Connect the power cord to the Power Input socket as shown in the illustration below and plug into power supply . The LEDs will flash to indicate that the device has powered up. The illustration shows the position of the ports and the diagnostic LEDs. The two ports are itemized as follows: Network 1 Port Connect to this port the RJ45 ...

  • Ringdale IP Router - page 4

    4 The LEDs are itemized as follows: Link (Y ellow) LED The Link LED indicates that the port is functionally connected to an external port. It lights up when the connected hub is turned on. If the LED does not light up, there may be a problem with the cabling or the hub. Write (Red) LED The write LED blinks when a data packet is being sent from that ...

  • Ringdale IP Router - page 5

    5 Using PeripheralVision ® to Configure the IP Router Full Installation and operational procedures for PeripheralVision ® are dealt with in the separate manual accompanying the Installation CD, refer to this if any problems are encountered in the procedure detailed below . Install PeripheralVision ® onto a PC on Network One. Using the Locate NPM ...

  • Ringdale IP Router - page 6

    6 Default Gateway IP Address Enter here the default gateway IP address for Network 1. DNS Name Server Address This information is not necessary . Local IP Address Enter here the router ’ s IP address for Network 2. Local IP Subnet Mask Enter here the subnet mask for Network 2. Click on Apply to register the new information. Passwords It is strong ...

  • Ringdale IP Router - page 7

    7 It is now necessary to tell the IP Router where to route the IP packets to. This is done by creating a Routing T able as above. Configure each route as follows. IP Address Enter here the IP Address of the subnet you want to route to. Subnet Mask Enter here the Subnet Mask of the above IP Address. Gateway Enter here the Gateway address of the abov ...

  • Ringdale IP Router - page 8

    8 Click on the Add Route button to add a new route. Click on the Edit Route button to change the configuration of an existing route. Click on the Delete Route button to remove a route. Once the routes have been set up as required, click on Apply . The Ringdale IP Router is now configured and will route your IP packets automatically as specified. Br ...

  • Ringdale IP Router - page 9

    9 T o forward a broadcast through the router to the required IP address click on Add . This will open the window below: Enter the IP address and click on OK . The IP address will be entered into the list. T o make changes to an IP address already on the list, click on the required address to select it and then click on Edit . This will open the abo ...

  • Ringdale IP Router - page 10

    10 The device is designed to operate in a typical office environment. Choose a site that is: Well ventilated and away from sources of heat including direct sunlight. Away from sources of vibration or physical shock. Isolated from strong electromagnetic fields produced by electrical devices. Provided with a properly grounded wall outlet. Do not atte ...

  • Ringdale IP Router - page 11

    11 Troubleshooting and Technical Reference Symptom Poss. Cause Action LEDs do not flash Power switched off Switch on at power-up Power cord not connected Plug in Router Fuse defect Replace fuse Link LED does No cable inserted Connect to hub not light up and Router Router not Check power supply powered up for Router Wrong cable type V erify cable se ...

  • Ringdale IP Router - page 12

    12 Technical Support Ringdale Ltd, Ringdale Inc. and Ringdale GmbH all have T echnical Support Departments. Their addresses and contact details are found on the back cover of this manual. Before you call: Please have the following information ready before calling: T ype of adapters installed in the System. The adapter settings and interrupt options ...

Manufacturer Ringdale Category Network Router

Documents that we receive from a manufacturer of a Ringdale IP Router can be divided into several groups. They are, among others:
- Ringdale technical drawings
- IP Router manuals
- Ringdale product data sheets
- information booklets
- or energy labels Ringdale IP Router
All of them are important, but the most important information from the point of view of use of the device are in the user manual Ringdale IP Router.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Ringdale IP Router, service manual, brief instructions and user manuals Ringdale IP Router. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Ringdale IP Router.

Similar manuals

A complete manual for the device Ringdale IP Router, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Ringdale IP Router by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Ringdale IP Router.

A complete Ringdale manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Ringdale IP Router - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Ringdale IP Router, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Ringdale IP Router, that we can find in the current document
3. Tips how to use the basic functions of the device Ringdale IP Router - which should help us in our first steps of using Ringdale IP Router
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Ringdale IP Router
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Ringdale IP Router in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Ringdale IP Router?

Use the form below

If you did not solve your problem by using a manual Ringdale IP Router, ask a question using the form below. If a user had a similar problem with Ringdale IP Router it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)