Manual NuTone NP503004

36 pages 1.44 mb
Download

Go to site of 36

Summary
  • NuTone NP503004 - page 1

    NP50000 Series ENGLISH ....................................... 2 FRANÇAIS ................................. 12 ESPAÑOL .................................. 22 Broan-NuTone LLC. 926 West State Street, Hartford, WI 53027 NuTone, Inc., 4820 Red Bank Road, Cincinnati, OH 45227 To Register this Product Visit www.Nutone.com ...

  • NuTone NP503004 - page 2

    2 READ AND SAVE THESE INSTRUCTIONS WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: 1 . Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer at the address or telephone number listed in the warranty. 2 . Before servicing or cleaning unit, switc ...

  • NuTone NP503004 - page 3

    3 ! CAUTION 1 . To reduce risk of fire and to properly exhaust air, be sure to duct air outside. Do not vent exhaust air into spaces within walls or ceilings or into attics, crawl spaces, or garages. 2 . Take care when using cleaning agents or detergents. 3 . Avoid using food products that produce flames under the Range Hood. 4. For general ventila ...

  • NuTone NP503004 - page 4

    4 PREPARE THE HOOD Unpack hood and check contents. You should receive: 1 - Hood 1 - Decorative Flue Assembly 1 - Adapter 2 - Non-ducted recirculation filters 1 - Parts Bag (B080810471) containing: 1 - Mounting Bracket 1 - Discharge Collar 1 - Flue Mounting Bracket MOUNTING BRACKET DISCHARGE COLLAR FLUE MOUNTING BRACKET 8 MOUNTING SCREWS (4.8 x 38mm ...

  • NuTone NP503004 - page 5

    5 ROOF CAP ROUND DUCT DECORATIVE FLUE HOOD WALL CAP 24” TO 30” ABOVE COOKING SURFACE INSTALL THE DUCTWORK (DUCTED HOODS ONLY) NOTE: To reduce the risk of fire, use only metal ductwork. 1. Decide where the ductwork will run between the hood and the outside. 2. A straight, short duct run will allow the hood to perform most efficiently. 3. Long du ...

  • NuTone NP503004 - page 6

    6 DISCHARGE COLLAR 6” DIAMETER DUCT DUCT CONNECTOR INSTALL FLUE MOUNTING BRACKET DUCTED AND NON-DUCTED 1. Assemble the flue mounting bracket, adjusting outside width as shown. Fig.5 2. Carefully center the mounting bracket directly over the range hood location. 3. Secure the bracket assembly to the ceiling using (2) 4.8x38mm mounting screws and d ...

  • NuTone NP503004 - page 7

    7 A fig.7 UPPER FLUE LOWER FLUE UPPER FLUE VENTS EXPOSED UPPER FLUE VENTS CONCEALED PLENUM (3) SCREWS 5” ALUMINUM FLEX DUCT 5” 6” ADAPTER BLOWER COLLAR PREPARE THE HOOD NON - DUCTED CONFIGURATION Note: The following materials must be purchased separately for non-ducted recirculation installations. • 5” diameter expandable / flexible alumi ...

  • NuTone NP503004 - page 8

    8 PREPARE THE HOOD NON - DUCTED CONFIGURATION, cont’d. 8. Carefully place the lower decorative flue into the recessed area of the range hood top. Fig.7 9. Carefully slide the upper decorative flue down inside the lower flue. Note: air vents must be up. Fig.7 10.Secure the recirculation plenum to the upper flue with (4) flat head screws. Fig.9 PLE ...

  • NuTone NP503004 - page 9

    9 Non-ducted recirculation filters The non-ducted recirculation filters should be changed every 6 months. Rotate the filters to remove and replace. Hood Cleaning Stainless steel is one of the easiest materials to keep clean. Occasional care will help preserve its fine appearance. Cleaning tips: • Hot water with soap or detergent is all that is us ...

  • NuTone NP503004 - page 10

    10 OPERATION Controls The hood is operated using the slide controls under the bottom of the hood. The light switch turns the lamps on and off. The blower switch : makes it possible to select the motor operating speed. Position 0: motor off. The pilot lamp lights up whenever the blower is on. HEAT SENTRY™ Your hood is equipped with a HEAT SENTRY? ...

  • NuTone NP503004 - page 11

    11 BROAN-NUTONE LLC ONE YEAR LIMITED WARRANTY Broan-NuTone LLC warrants to the original consumer purchaser of its products that such products will be free from defects in materials or workmanship for a period of one year from the date of original purchase. THERE ARE NO OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WAR ...

  • NuTone NP503004 - page 12

    12 LISEZ ET CONSERVEZ CES INSTRUCTIONS AVERTISSEMENTS POUR REDUIRE LES RISQUES D’INCENDIE, DE DECHARGES ELECTRIQUES OU DE DOMMAGES AUX PERSONNES, OBSERVEZ LES INSTRUCTIONS SUIVANTES: 1 . N’utilisez cet appareil que comme cela est indiqué par le constructeur. Si vous avez des problèmes, contactez le fabriquant à l’adresse ou au numéro de t ...

  • NuTone NP503004 - page 13

    13 4 . Utilisez un extincteur SEULEMENT si: A . Vous savez que vous avez un extincteur Classe ABC, et vous en connaissez déjà le mode d’emploi. B . Ce n’est pas un très gros incendie et qu’il se limite à l’endroi où il a explosé. C. Vous êtes en train d’avertir les pompiers. D . Vous avez la possibilité d’essayer d’éteindre l ...

  • NuTone NP503004 - page 14

    14 PREPAREZ LA HOTTE Enlever la hotte dans l’emballage et controller le contenu. Vous devez recevoir : 1 - Hotte 1 - Conduit décoratif 1 - Adaptateur 2 - Filtres version recyclant l’air 1 - Sachet (B080810471) avec: 1 - Étrier d’assemblage 1 - Collier d’évacuation 1 - Étrier de support ETRIER D’ASSEMBLAGE COLLIER D’EVACUATION ETRIER ...

  • NuTone NP503004 - page 15

    15 CHATIÈRE AU PLAFOND CONDUIT ROND CARNEAU DÉCORATIF HOTTE CHATIÈRE MURALE 24" TO 30" SURFACE AU-DESSUS DE LA ZONE DE CUISSON INSTALLATION DES CONDUITS (UNIQUEMENT POUR LES HOTTES CARÉNÉES) REMARQUE: pour réduire les risques d’incendie, utilisez uniquement des conduits métalliques. 1. Choisissez l’endroit où passera le condui ...

  • NuTone NP503004 - page 16

    16 7 - 3/4” (197mm) fig.6 COLLET DE REFOULEMENT DIAMÈTRE DU CONDUIT 6” CONNECTEUR DU CONDUIT INSTALLATION DU SUPPORT DE FIXATION DU CARNEAU CARÉNÉ ET NON CARÉNÉ 1. Assemblez le support de fixation du carneau en réglant la largeur extérieure comme indiqué. Fig.5. 2. Centrez soigneusement le support de fixation directement sur l’emplace ...

  • NuTone NP503004 - page 17

    17 A CONFIGURATION CARÉNÉE 1. Installez le collet de refoulement dans le conduit relié à la hotte (fig.6). 2. Attachez un conduit arrondi en acier d’une longueur de 6" au connecteur du conduit de la hotte (fig.6). 3. Reliez toutes les sections pour empêcher le passage de l’air. 4. Placez précautionneusement le carneau décoratif inf? ...

  • NuTone NP503004 - page 18

    18 PRÉPARATION DE LA HOTTE CONFIGURATION NON CARÉNÉE (suite). 8. Placez précautionneusement le carneau décoratif inférieur dans la partie de la hotte en retrait (fig.7). 9 . Faites glisser lentement le carneau décoratif à l’intérieur du conduit inférieur. Remarque: les prises d’air doivent être tournées vers le haut (fig.7). 10 . Fi ...

  • NuTone NP503004 - page 19

    19 FILTRE ANTI-GRAISSE FILTRES VERSION RECYCLANT L’AIR fig.12 fig.13 Filtres version recyclant l’air Les filtres version recyclant l’air l’air doivent être remplacés tous les 6 mois. Faites tourner les filtres afin de les enlever et de les remettre. Nettoyage de votre hotte L’acier inoxydable est une des matières les plus faciles à ne ...

  • NuTone NP503004 - page 20

    20 fig.14 LIGHT SWITCH PILOT LAMP BLOWER SWITCH 01 01234 fig.15 FONCTIONNEMENT Commandes La hotte peut être manœuvrée à l’aide des curseurs situés sous la partie inférieure de la hotte. L’ interrupteur de la lumière allume et éteint les lampes. L’ interrupteur du ventilateur permet de sélectionner la vitesse de marche du moteur. Posi ...

  • NuTone NP503004 - page 21

    21 GARANTIE BROAN-NUTONE LLC LIMITÉE À UN AN Broan-NuTone LLC garantit au consommateur-acheteur de ses produits que ces produits seront sans défauts concernant les matières employées et concernant la fabrication pendant une période d’un an à partir de la date d’achat. IL N’Y A AUCUNE AUTRE GARANTIE, EXPLICITE OU IMPLICITE, Y COMPRIS, M ...

  • NuTone NP503004 - page 22

    22 LEA Y CONSERVE ESTAS INSTRUCCIONES ADVERTENCIA PARA EVITAR EL RIESGO DE INCENDIO, CORTOCIRCUITO O DAÑO PARA LAS PERSONAS, OBSERVE ATENTAMENTE LAS SIGUIENTES NORMAS: 1 . Use esta unidad solamente de la manera indicada por el fabricante; si tiene dudas, póngase en contacto con éste a la dirección o teléfono indicados en la garantía. 2 . Ante ...

  • NuTone NP503004 - page 23

    23 ! ADVERTENCIA 1. Para reducir el riesgo de incendios y para evacuar correctamente los humos, asegurarse de haber realizado una conducción del aire hasta el exterior. No expulsar los humos en espacios cerrados por paredes o techos, áticos, espacios angostos o garajes. 2 . Prestar la máxima atención al utilizar productos de limpieza o detergen ...

  • NuTone NP503004 - page 24

    24 PREPARE LA CAMPANA Sacar la campana de l’embalaje y controlar el contenido. Recivireis: 1 - Campana 1 - Tubo decorativo 1 - Reducción 2 - Filtros configuración sin tubo 1 - Bolsita (B080810471) con: 1 - Soporte de montaje 1 - Casquillo 1 - Soporte para el montaje del tubo SOPORTE DE MONTAJE CUELLO DE DESCARGA SOPORTE PARA EL MONTAJE DEL TUBO ...

  • NuTone NP503004 - page 25

    25 TAPA DE TECHO CONDUCTO REDONDO SALIDA DE HUMOS DECORATIVA CAMPANA TAPA DE PARED 24" – 30" SOBRE LA SUPERFICIE DE COCCIÓN INSTALACIÓN DEL CONDUCTO (SÓLO CAMPANAS CON CONDUCTO) NOTA: Para reducir el riesgo de fuego, utilice sólo conductos de metal. 1. Decida el lugar entre la campana y el exterior en el que colocará el conducto. 2 ...

  • NuTone NP503004 - page 26

    26 CUELLO DE DESCARGA CONDUCTO DE 6" DE DIÁMETRO CONECTOR DE CONDUCTO SOPORTE DE MONTAJE DE LA SALIDA DE HUMOS 7 - 3/4” (197mm) TORNILLOS DE MONTAJE DE CABEZA PLANA D E 3.9x6mm INSTALACION DE LOS SOPORTES PARA EL MONTAJE 1. Construya una estructura de madera en la pared que quedará nivelada con la parte interior de los tacos en la pared. A ...

  • NuTone NP503004 - page 27

    27 A superficies exteriores de la campana y de las salidas de humo decorativas. CONFIGURACIÓN CON CONDUCTO 1 . Instale el cuello de descarga en el conector de conducto de la campana de cocina. Fig.6 2. Conecte un conducto redondo de acero de 6" al conector de conducto de la campana de cocina. Fig.6 3 . El conducto tapa todas las juntas, asegu ...

  • NuTone NP503004 - page 28

    28 PREPARACIÓN DE LA CAMPANA CONFIGURACIÓN SIN CONDUCTO, continuación 8. Coloque con cuidado la salida de humos decorativa inferior en el área empotrada de la parte superior de la campana de cocina. Fig.7 9 . Deslice cuidadosamente la salida de humos decorativa superior hacia abajo, dentro de la salida de humos inferior. Nota: los respiraderos ...

  • NuTone NP503004 - page 29

    29 Filtros configuración sin tubo Los filtr os configuración sin tubo cambiarse cada seis meses. Gire los filtros para desenroscarlos y cambiarlos. Limpieza de la campana El acero inoxidable es uno de los meteriales más fáciles de limpiar, pero sería aconsejable un especial cuidado en su uso para mantenerla en buen estado. La campana se puede ...

  • NuTone NP503004 - page 30

    30 FUNCIONAMIENTO Mandos La campana se controla mediante los mandos corrrederos situados en la parte inferior de la misma. El interruptor da luz enciende y apaga las lámparas. El interruptor del aspirador: regula la velocidad de trabajo del motor. Posición 0: motor apagado. El piloto se enciende cuando el aspirador está funcionando. HEAT SENTRY ...

  • NuTone NP503004 - page 31

    31 GARANTIA BROAN-NUTONE LLC POR UN AÑO Broan-NuTone LLC garantiza al consumidor-comprador de sus productos que dichos productos no tendrán defectos en los materiales o fabricación, durante un periodo de un año a partir de la fecha de la compra. NO HAY OTRO TIPO DE GARANTIAS QUE INCLUYAN O SE LIMITEN EXCLUSIVAMENTE A GARANTIAS IMPLICITAS O DE C ...

  • NuTone NP503004 - page 32

    32 SERVICE PARTS NP50000 SERIES RANGE HOOD - Parts for stainless steel models shown. For service parts for black, white, polished brass, or brushed copper models, call Broan Customer Service. KEY NO. PART NO. DESCRIPTION 9 B08087292 Grease Filter 1 4 B02300233 Motor Capacitor 1 6 BE3244974 Electrical Box Support 2 6 B02300264 Lamp Bulb 2 8 B0230028 ...

  • NuTone NP503004 - page 33

    33 LISTE PIECES DE RECHANGE NP50000 SERIES RANGE HOOD - Ci-dessous liste pièces de rechange pour hottes en inox. Pour les pièces de recharge des modèles de couleurs noir, blanc, laiton jaune poli, cuivre brossé, contacter Broan Customer Service. N. PART N. DESCRIPTION 9 B08087292 Filtre anti-graisse 1 4 B02300233 Condensateur 1 6 BE3244974 Supp ...

  • NuTone NP503004 - page 34

    34 CÓD. N. PIEZA N. DESCRIPCIÓN 9 B08087292 Filtro antigrasa 1 4 B02300233 Condensador 1 6 BE3244974 Soporte de la caja de instalación eléctrica 26 B02300264 Lámpara 2 8 B02300280 Soporte de la lámpara 29 B08099902 Tapas de la lámpara 3 7 B02300787 Sensor de temperatura 45 BW0000019 Convoyador 4 8 B02310177 Moto r 4 9 B03295076 Manilla de mo ...

  • NuTone NP503004 - page 35

    35 SERVICE PARTS - LISTE PIECES DE RECHANGE - LISTA DE PIEZAS DE RECAMBIO NP50000 SERIES RANGE HOOD ...

  • NuTone NP503004 - page 36

    04307655/2S ...

Manufacturer NuTone Category Ventilation Hood

Documents that we receive from a manufacturer of a NuTone NP503004 can be divided into several groups. They are, among others:
- NuTone technical drawings
- NP503004 manuals
- NuTone product data sheets
- information booklets
- or energy labels NuTone NP503004
All of them are important, but the most important information from the point of view of use of the device are in the user manual NuTone NP503004.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals NuTone NP503004, service manual, brief instructions and user manuals NuTone NP503004. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product NuTone NP503004.

Similar manuals

A complete manual for the device NuTone NP503004, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use NuTone NP503004 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of NuTone NP503004.

A complete NuTone manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual NuTone NP503004 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the NuTone NP503004, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the NuTone NP503004, that we can find in the current document
3. Tips how to use the basic functions of the device NuTone NP503004 - which should help us in our first steps of using NuTone NP503004
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with NuTone NP503004
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of NuTone NP503004 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning NuTone NP503004?

Use the form below

If you did not solve your problem by using a manual NuTone NP503004, ask a question using the form below. If a user had a similar problem with NuTone NP503004 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)