English dropdown-ico

Manual InFocus IN136UST

66 pages 3.57 mb
Download

Go to site of 66

Summary
  • InFocus IN136UST - page 1

    ...

  • InFocus IN136UST - page 2

    Copyright This publication, includin g all photographs, illustrati ons and softwa re, is protected under international copyright laws, with all rig hts reserved. Neither this manual, nor any of the material contained h erein, may be reproduced without written consent of the author. © Copyright 2013 Disclaimer The information in this docu ment is s ...

  • InFocus IN136UST - page 3

    IN134UST/IN136UST User’s Manual Important Safety Information Important: It is strongly recommended that you read this sect ion carefully b efore using the projector. These safety and usage instructions will ensure that you enj oy many years of safe use of the pr ojector. Keep this manual for future reference. Symbols Used Warning symbols are u se ...

  • InFocus IN136UST - page 4

    Preface Projector Installation Notice  Place the projector in a horizontal p osition The tilt angle of the projector should not excee d 15 degrees, nor should the proje ctor be installed in any way other than the desktop and ceiling mou nt, ot herwise lamp life could decrease dramatically.  Allow at least 50 cm clearance around th e exhaust v ...

  • InFocus IN136UST - page 5

    IN134UST/IN136UST User’s Manual GS Mark Associated address: INFOCUS INTERNATIONAL B.V. CASABLANCAWEG 14 BLD A4 1047 HP AMSTERDAM NL About this manual This manual is intended for end users and descri bes how to install and operate the DLP projector. Wherever possible, releva nt information—such as an illustration and its de scription—has been ...

  • InFocus IN136UST - page 6

    Preface – v – Table of Contents GETTING STARTED ........................................................................................................................................................... 1 P ACKING C HECKLIST ........................................................................................................................ ...

  • InFocus IN136UST - page 7

    IN134UST/IN136UST User’s Manual — vi — L AMP P ROBLEMS ............................................................................................................................................................... 47 R EMOTE C ONTROL P ROBLEMS ................................................................................................... ...

  • InFocus IN136UST - page 8

    IN134UST/IN136UST User’s Manual – 1 – G ETTING S TARTED Packing Checklist Carefully unpack the projector and che ck that the following items are included: DLP P ROJ ECTO R R EMOTE CONTROL (B ATTERIES NOT INCLUDED ) P O WER CORD VGA C ABLE CD-ROM (T HIS U SER ’ S MANUAL ) Q UICK S TART G UIDE S AFETY & W ARRANTY B OOKLET Contact your dea ...

  • InFocus IN136UST - page 9

    IN134UST/IN136UST User’s Manual Views of Projector Parts Front-right View 13 4 5 26 I TEM L ABEL D ESCRIP TION S EE PAGE 1. Lamp cover Remove cover to replace lamp modul e 2. IR receiver Receives IR si gnal from remote control 3. Aspheric mirror Reflects images 4. Lens Projection Lens 5. Focus ring Focuses the projected image 6. Function keys See ...

  • InFocus IN136UST - page 10

    IN134UST/IN136UST User’s Manual Top view—On-screen Displa y (OSD) buttons and LEDs 1 6 2 3 4 5 12 7 8 9 10 11 I TEM L ABEL D ESCRIPTION S EE PAGE 1. MENU Opens and exits OSD me nus 2. Navigates in the OSD Keystone adjustment (whe n OSD menu is closed) 16 3. SOURCE Enter the Source menu 4. Navigates and changes settings in the OSD Volume adjustm ...

  • InFocus IN136UST - page 11

    IN134UST/IN136UST User’s Manual Rear view 15 16 12 3 4 56 7 89 10 14 13 12 1 1 I TEM L ABEL D ESCRIPTION S EE PAGE 1. Security bar For security purpos es 2. Kensington lock Secure to a permanent object with a Ke nsington® Lock system 44 3. 3D SYNC Connect the 3D IR glasses transmitter (Note: For Vivitek brand 3D IR glasses only) 4. AUDIO IN Conn ...

  • InFocus IN136UST - page 12

    IN134UST/IN136UST User’s Manual – 5 – I TEM L ABEL D ESCRIPTION S EE PAGE 14. VIDEO Connect a composite cable from a video device 15. HDMI Connect an HDMI cable from a HDMI device 16. RJ45 Connect a LAN cable from Ethernet Note: If your video equipment has various input sources, it is recommended that you connect the cables in the following o ...

  • InFocus IN136UST - page 13

    IN134UST/IN136UST User’s Manual Bottom view — 6 — 2 47. 0 1 135.51 1 2 2 2 1 1 I TEM L ABEL D ESCRIPTION S EE PAGE 1. Tilt adjustor Rotate adjuster lever to adjust angl e position 14 2. Ceiling support holes Contact your dealer for information on m ounting the projector on a ceiling Note: When installing, ensure that you us e only UL Listed c ...

  • InFocus IN136UST - page 14

    IN134UST/IN136UST User’s Manual Remote Control Par ts 12 3 4 5 6 7 8 9 10 11 12 13 14 15 Important: 1. Avoid using the projector with bright fluore scent lighting turned on. Certain high-frequency fluorescent lights can disrupt remote control operation. 2. Be sure nothing obstructs the path between the remote control and the pr ojector. If the pa ...

  • InFocus IN136UST - page 15

    IN134UST/IN136UST User’s Manual — 8 — I TEM L ABEL D ESCRIPTION S EE PAGE : 1. Up cursor Navigates and changes settings in the OSD 2. Enter Changes settings in the OSD 16 3. Power Turns the projector on or of f 11 4. Right cursor Navigates and changes settings in the OSD 5. Volume + Increa ses volume 6. Volume - Decrease s volume 15 7. Mute M ...

  • InFocus IN136UST - page 16

    IN134UST/IN136UST User’s Manual – 9 – Remote Control Operating Range The remote control uses infrared transmission to cont rol the projector. It is not necessary to point the remote directly at the projector. Provided you are not holding the remote perpendicular to the sides or the rear of the projector, the re mote will function well within ...

  • InFocus IN136UST - page 17

    IN134UST/IN136UST User’s Manual — 10 — S ETUP AND O PERATION Inserting the Remote Control Batteries 1. Remove the battery compartment cover by sliding the cover in the direction of the arrow (A) . Pull out the cover (B) . 2. Insert the battery with the positive side facing up. 3. Replace the cover. Caution: 1. Only use a 3V lithium battery (C ...

  • InFocus IN136UST - page 18

    IN134UST/IN136UST User’s Manual Starting and Shutting down t he Project or 1. Connect the power cord to the projector. Connect the other end to a wall outlet. 2. Turn on the connected devices. 3. Ensure the POWER LED displays a solid green. Then press the POWER button of the remote to turn on the projector. The projector splash screen displays an ...

  • InFocus IN136UST - page 19

    IN134UST/IN136UST User’s Manual Setting an Access Password (Secu rity Lock) You can use the four (arrow) buttons to set a password and pr event u nauthorized use of the projector. When enabled, the password must be entered after you p ower on the projector. (See Navigating the OSD on page 16 and Setting the OSD Langua ge on page 17 for help on us ...

  • InFocus IN136UST - page 20

    IN134UST/IN136UST User’s Manual 4. Press the ▲▼ buttons to select Security Lock . 5. Press the ◄► buttons to enable or disable security lock function. A password dialog box automatically appears. 6. You can use the cursor buttons ▲▼◄► on IR remote control for password entry. You can use any combination including the same arrow fiv ...

  • InFocus IN136UST - page 21

    IN134UST/IN136UST User’s Manual Adjusting the Projector Level Take note of the following when setting up the projector:  The projector t able or stand should be level and sturdy .  Position the projector so that it is perpendicular t o the screen.  Ensure the cables are in a safe location. Y ou could trip over them. To adjust the angle o ...

  • InFocus IN136UST - page 22

    IN134UST/IN136UST User’s Manual Adjusting the Focus and Keystone 1. Use the Image-focus control (on the projector only) to sharpen the projected image. 2. Use the KEYSTONE buttons the remote control to correct trapezoid image issues (wider top or bottom). 3. The keystone control appears on the display. Adjusting the Volume 1. Press the Volume +/- ...

  • InFocus IN136UST - page 23

    IN134UST/IN136UST User’s Manual — 16 — O N -S CREEN D ISPLAY (OSD) M ENU S ETTINGS OSD Menu Controls The projector has an OSD that lets you ma ke image adjustments and c hange various settings. Navigating the OSD 2 1 1 2 3 4 1 1 2 4 5 6 5 6 3 You can use the remote control cursor butt on to navigate and make changes to the OSD. 1. To enter th ...

  • InFocus IN136UST - page 24

    IN134UST/IN136UST User’s Manual Setting the OSD Language Set the OSD language to your pr eference before continuing. 1. Press the MENU button. Press the ◄► buttons to navigate to Installation I. 2. Press the ▲▼ buttons until Language is highlighted. 3. Press the ◄► buttons until the language you want is highlighted. 4. Press the MENU ...

  • InFocus IN136UST - page 25

    IN134UST/IN136UST User’s Manual OSD Menu Overview Use the following illustration to quickly find a se tting or determine the range for a setting. — 18 — ...

  • InFocus IN136UST - page 26

    IN134UST/IN136UST User’s Manual OSD Sub-Menu Overvie w Installation II / Advanced / Periphera l Test Remote Control Test Installation II / St atus Video in formati on Active Source Image / Advanc ed / Color Manager Red Hue Saturation Gain Lamp Hours(Normal, Bright) Color Test Color Temperat ure Color Space Color Manager Native , Warm , Normal , C ...

  • InFocus IN136UST - page 27

    IN134UST/IN136UST User’s Manual Image Menu Press the MENU button to open the OSD menu. Press the ◄► buttons to move to the Image Menu . Press the ▲▼ buttons to move up and down in the Image menu. Press ◄► to change setting values. I TEM D ESCRIPTION Display Mode Press the ◄► buttons to set the Display Mode. Note : Display Mode mus ...

  • InFocus IN136UST - page 28

    IN134UST/IN136UST User’s Manual Advanced Features Press the Menu button to open the OSD menu. Press ◄► to move to the Image menu. Press ▼▲ to move to the Advanced menu and then press Enter or ► . Press ▼▲ to move up and down in the Advanced menu. I TEM D ESCRIPTION Color Space Press the ◄► buttons to adjust the color space. (Ran ...

  • InFocus IN136UST - page 29

    IN134UST/IN136UST User’s Manual Color Manager Press (Enter) / ► to enter the Color Manager sub menu. I TEM D ESCR IPTION Red Select to enter the Red Color Manage r. Press the ◄► buttons to adjust the Hue, Saturation, and Gain. Green Select to ente r the Green Color Manager. Press the ◄► buttons to adjust the Hue, Saturation, and Gain. B ...

  • InFocus IN136UST - page 30

    IN134UST/IN136UST User’s Manual Computer Menu Press the MENU button to open the OSD menu. Press the ◄► buttons to move to the Computer menu. Press the ▲▼ buttons to move up and down in the computer menu. Press ◄► to change setting values. I TEM D ESCRIPTION Horizontal Position Press the ◄► buttons to adjust the display position to ...

  • InFocus IN136UST - page 31

    IN134UST/IN136UST User’s Manual Video Menu Press the MENU button to open the OSD menu. Press the ◄► buttons to move to the Video menu. Press the ▲▼ buttons to move up and down in the Video menu. Press ◄► to change setting values. Note: Available settings vary depending on the input source. Others will appear grayed out. I TEM D ESCRIP ...

  • InFocus IN136UST - page 32

    IN134UST/IN136UST User’s Manual Audio Press (Enter) / ► to enter the Audio sub menu. I TEM D ESCRIP TION Volume Press the ◄► buttons to adjust the audio volume. Mute Press the ◄► buttons to turn on or off the speaker. Audio Input Press the ◄► buttons to select audio input. – 25 – ...

  • InFocus IN136UST - page 33

    IN134UST/IN136UST User’s Manual Installation I Menu Press the MENU button to open the OSD menu. Press the ◄► buttons to move to the Installation I menu. Press the ▲▼ buttons to move up and down in the Installation I menu. Press ◄► to change setting values. I TEM D ESCRIP TION Language Press the ◄► buttons to change the OSD languag ...

  • InFocus IN136UST - page 34

    IN134UST/IN136UST User’s Manual Advanced Features Press the Menu button to open the OSD menu. Press ◄► to move to the Installation I menu. Press ▲▼ to move to the Advanced menu and then press Enter or ► . Press ▲▼ to move up and down in the Advanced menu. Press ◄► to change setting values. I TEM D ESCR IPTION Security Lock Press ...

  • InFocus IN136UST - page 35

    IN134UST/IN136UST User’s Manual Presentation Timer The Presentation Timer func tion can indicate the presentation ti me on the screen to help you achieve better time management while giving a presentation. I TEM D ESCR IPTION Timer Press the ◄► buttons to enable or disabl e the presentation timer. Timer Period Press the ◄► buttons to sele ...

  • InFocus IN136UST - page 36

    IN134UST/IN136UST User’s Manual Installation II Menu Press the MENU button to open the OSD menu. Press the ◄► buttons to move to the Installation II menu. Press the ▲▼ buttons to move up and down in the Installation II menu. I TEM D ESCR IPTION Auto Source Press the ◄► buttons to enable or disable automatic so urce detection. Auto Pow ...

  • InFocus IN136UST - page 37

    IN134UST/IN136UST User’s Manual Advanced Features Press the Menu button to open the OSD menu. Press ◄► to move to the Installation II menu. Press ▲▼ to move to the Advanced menu and then press Enter or ► . Press ▲▼ to move up and down in the Advanced menu. Press ◄► to change setting values. I TEM D ESCR IPTION OSD Menu Setting P ...

  • InFocus IN136UST - page 38

    IN134UST/IN136UST User’s Manual OSD Menu Setting I TEM D ESCRIPTION Menu Position Press the ◄► buttons to select a different OSD location. Translucent Menu Press the ◄► buttons to select the OS D background translucent level. Menu Display Press the ◄► buttons to select the OSD timeout delay. Peripheral Test I TEM D ESCRIPTION Remote C ...

  • InFocus IN136UST - page 39

    IN134UST/IN136UST User’s Manual Lamp Hour Reset Please refer to Resetting the Lamp on page 41 to reset the lamp hour counter. — 32 — ...

  • InFocus IN136UST - page 40

    IN134UST/IN136UST User’s Manual 3D I TEM D ESCRIPTION 3D Press the ◄► buttons to select Off, DLP-Link or IR. 3D Sync Invert Press the ◄► buttons to turn 3D Sync Invert On or Off. 3D Format Press the ◄► buttons to enable or disable 3D Format. Note: 1. By default, if no 3D sou rce is detected, the 3D OSD menu item s will not be availabl ...

  • InFocus IN136UST - page 41

    IN134UST/IN136UST User’s Manual Network I TEM D ESCRIPTION Network State Displays the network conn ection status. DHCP Press ◄► to turn DHCP On or Off. Note: If you select DHCP Off, complete the IP Address, Subnet Mask, Gateway, and DNS fields. IP Address Enter a valid IP address if DHCP is turned off. Subnet Mask Enter a valid Subnet Mask if ...

  • InFocus IN136UST - page 42

    IN134UST/IN136UST User’s Manual For simplicity and ease of operation, the proj ector provides diverse networking and rem ote management features. The LAN/RJ45 feature allo ws the projector to be conn ected to a net work and remotely manage d. Available remote management controls incl ude: Power On/Off, Video-Source, Br ightness and Cont rast sett ...

  • InFocus IN136UST - page 43

    IN134UST/IN136UST User’s Manual 2. From the Homepage of LAN/RJ45, click Alert Mail Settings . 3. By default, the input boxes in Alert Mail Settings a re blank. 4. To setup email alerts, input the following:  　 The SMTP field is the mail server for sendi ng out email (SMTP protocol). This is a required field.  　 The To field is the recip ...

  • InFocus IN136UST - page 44

    IN134UST/IN136UST User’s Manual Note: Fill in all fields as specified. Select the desired alert condition and click Submit to conduct an Email Alert Test . A successful test alerts t he designated email accounts. To create an email alert, you must select alert conditions and enter a correct email address. Group and Name identify the alerting proj ...

  • InFocus IN136UST - page 45

    IN134UST/IN136UST User’s Manual Factory Reset Press the ▲▼ buttons to move up and down in the Installation II menu. Select the Factory Reset sub menu and press (Enter) / ► to reset all the menu items to t he factory default values (except Language and Security Lock). Status Press the ▲▼ buttons to move up and down in the Installation II ...

  • InFocus IN136UST - page 46

    IN134UST/IN136UST User’s Manual – 39 – M AINTENANCE AND S ECURITY Replacing the Projection Lamp The projection lamp should be replaced when it burns out. It should only be r eplaced with a certified replacement part, which you can order from your local dealer. Important: a. The projection lamp used in this produc t contains a small amount of ...

  • InFocus IN136UST - page 47

    IN134UST/IN136UST User’s Manual 2. Remove the lamp compartment cover. 3. Loosen the two screws from the lamp module. 4. Lift the module handle up. 5. Pull firmly on the module handle to remove the lamp module. 6. Reverse steps 1 to 5 to install the new lamp module. While installing, align the lamp module with the connector and ensure it is level ...

  • InFocus IN136UST - page 48

    IN134UST/IN136UST User’s Manual Resetting the Lamp After replacing the lamp, you should reset the lamp hour counter to zero. Refer to the following: 1. Press the MENU button to open the OSD menu. 2. Press the ◄► buttons to move to the Installation II menu. Press the cursor button to move down to Advanced . 3. Press the ▼▲ buttons to move ...

  • InFocus IN136UST - page 49

    IN134UST/IN136UST User’s Manual Cleaning the Projector Cleaning the projector to remove dust and gr ime will help ensure trouble-free operation. Cleaning the Projector Mirror: 1. Remove dust the lens with a lens blower (available from most camera shops) to prevent scratching the mirror when it is wiped. 2. Gently wipe the lens with a lens cleanin ...

  • InFocus IN136UST - page 50

    IN134UST/IN136UST User’s Manual Cleaning the Case Follow these instructions to clean the projector case: 1. Wipe off dust with a clean dampened cloth. 2. Moisten the cloth with warm water and mild det ergent (such as used to wash dishes), and then wipe the case. 3. Rinse all detergent from the cl oth and wipe the projector again. Caution: To prev ...

  • InFocus IN136UST - page 51

    IN134UST/IN136UST User’s Manual Using the Physical Lock Using the Kensington ® Lock If you are concerned about security, attach the proj ector to a permanent obje ct with the Kensington slot and a security cable. Note: Contact your vendor for details on purchasing a suitable Kensi ngton security cable. The security lock corresponds to Kensington ...

  • InFocus IN136UST - page 52

    IN134UST/IN136UST User’s Manual – 45 – T ROUBLESHOOTING Common problems and solut ions These guidelines provide tips to deal with problem s you may encounter while using the projector. If the problem remains unsolved, cont act your dealer for assistance. Often after time spent troubleshooting, the problem is traced to so mething as simple as ...

  • InFocus IN136UST - page 53

    IN134UST/IN136UST User’s Manual — 46 — LED Error Messages E RROR C ODE M ES SAGES P OWER LED G REEN L AMP LED A MBER T EMP LED R ED Power On ON OFF OFF Power Off ON OFF OFF Cooling Flashing OFF OFF Over Temperature OFF OFF ON Thermal Break Sensor error 4 blinks OFF OFF Lamp error OFF ON OFF Fan 1 6 blinks 1 blink OFF Fan 2 6 blinks 2 blinks O ...

  • InFocus IN136UST - page 54

    IN134UST/IN136UST User’s Manual – 47 – Problem: The color of the projected image does not match the source image. Adjust the Color Temperature and Gamma settings on the Image menu of the OSD. Lamp Problems Problem: There is no light from the projector 1. Check that the power cable is securely connected. 2. Ensure the power source is good by t ...

  • InFocus IN136UST - page 55

    IN134UST/IN136UST User’s Manual — 48 — HDMI Q & A Q. What is the difference between a “Standard” HDMI cable and a “High-Speed” HDMI cable? 1. Recently, HDMI Licensing, LLC announced that cables would be tested as Standard or High-Speed cables. 2. ˙ Standard (or “category 1”) HDMI cabl es have been tested to perform at speeds ...

  • InFocus IN136UST - page 56

    IN134UST/IN136UST User’s Manual – 49 – S PECIFICATIONS Specifications Model IN134UST IN136UST Display type DMD 0.55" XGA DMD 0.65" WXGA Native Resolution XGA 1024 x 768 Native WXGA 1280 x 800 Native Projection distance 371~417mm 336~42 1mm Projection screen size (diagonal) 4:3 (68"~85”) 16:10 (80”~100”) Projection lens Ma ...

  • InFocus IN136UST - page 57

    IN134UST/IN136UST User’s Manual Projection Distance vs. Projection Si ze Projection Distance and Size Table IN136UST WXGA 16:10 Diagonal 80" 87" 97" 100" Distance 282.3+/-20mm 336.3+/-20m m 421.4+/-20mm 445.8+/-20mm Image Width 1723mm 1869mm 2088mm 2154mm Image Height 1077mm 1168mm 1305mm 1346mm H 280+/-50mm 298.5+/-50mm 325.5 ...

  • InFocus IN136UST - page 58

    IN134UST/IN136UST User’s Manual – 51 – Timing Mode Table The projector can display several resolutions. The following table outlines the resolutions that can be displayed by the projector. S IGNAL R ESOLUTION H-S YNC (KH Z ) V-S YNC (H Z ) C OMPOSITE S_V IDEO C OMPONENT RGB (A NALOG ) DVI/ HDMI (D IGITAL ) NTSC － 15.734 60.0 ○ － － － ...

  • InFocus IN136UST - page 59

    IN134UST/IN136UST User’s Manual — 52 — S IGNAL R ESOLUTION H-S YNC (KH Z ) V-S YNC (H Z ) C OMPOSITE S_V IDEO C OMPONENT RGB (A NALOG ) DVI/ HDMI (D IGITAL ) *** 1280 X 1024 64.0 60.0 － － ○ ○ 1280 X 1024 80.0 75.0 － － ○ ○ 1280 X 1024 91.1 85.0 － － ○ ○ *** 1280 X 960 60.0 60.0 － － ○ ○ 1280 X 960 85.9 85.0 － ? ...

  • InFocus IN136UST - page 60

    IN134UST/IN136UST User’s Manual – 53 – S IGNAL R ESOLUTION H-S YNC (KH Z ) V-S YNC (H Z ) C OMPOSITE S_V IDEO C OMPONENT RGB (A NALOG ) DVI/ HDMI (D IGITAL ) 1080 P 56.3 50.0 － ○ － ○ 1080 P 67.5 60.0 － ○ － ○ O: Frequency supported —: Frequency not supported  3D no te ： “  ” means the timing can support non-3D and ...

  • InFocus IN136UST - page 61

    IN134UST/IN136UST User’s Manual Projector Dimensions — 54 — 160.0 122.58 374.51 ...

  • InFocus IN136UST - page 62

    IN134UST/IN136UST User’s Manual – 55 – R EGULATORY C OMPLIANCE FCC Warning This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipm ent is operated in a commercial ...

  • InFocus IN136UST - page 63

    IN134UST/IN136UST User’s Manual — 56 — A PPENDIX I Communication The following table describes the serial comm unication configuration t hat should be used when interfacing to the CLI via the serial port. Windows HyperTerminal or Procomm are two tool s that can be used to send CLI commands across the serial port. Setting Value Bits per second ...

  • InFocus IN136UST - page 64

    IN134UST/IN136UST User’s Manual – 57 – No Function Command RW Min Max Default Step Parameter 16 Color Temp TMP RW 0 3 Source Specific 1 Display Mode=User onl y 0:Native 1:Warm 2:Normal 3:Cold 17 Contrast CON RW 0 100 50 1 Display Mode=User only 18 Current Source SRC RW 0 4 0 1 0:VGA1 1:VGA2 5:HDMI 12:Composite 13:S-Video 21 Digital Zoom DZM R ...

  • InFocus IN136UST - page 65

    IN134UST/IN136UST User’s Manual — 58 — No Function Command RW Min Max Default Step Parameter 63 Language LAN RW 0 20 0 1 0:English 1:French 2:German 3:Spanish 4: Simp Chinese 5: Trad Chines e 6: Italian 7: Norwegian 8: Swedish 9: Dutch 10:Russian 11: Finnish 12: Korean 13: Arabic 14: Turkish 15: Japanese 16: Brazilian Portuguese 17: Vietnames ...

  • InFocus IN136UST - page 66

    IN134UST/IN136UST User’s Manual – 59 – No Function Command RW Min Max Default Step Parameter 117 Projector Low Power (Eco) Hours LTE R 0 9999 Displays the numbers of hours that the projector has run in Low Power (Eco) mode over its life (including all lamps). 118 Projector Model MDL R string IN134U ST / IN136UST 119 Projector Resolution NRS R ...

Manufacturer InFocus Category Projector

Documents that we receive from a manufacturer of a InFocus IN136UST can be divided into several groups. They are, among others:
- InFocus technical drawings
- IN136UST manuals
- InFocus product data sheets
- information booklets
- or energy labels InFocus IN136UST
All of them are important, but the most important information from the point of view of use of the device are in the user manual InFocus IN136UST.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals InFocus IN136UST, service manual, brief instructions and user manuals InFocus IN136UST. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product InFocus IN136UST.

Similar manuals

A complete manual for the device InFocus IN136UST, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use InFocus IN136UST by users. Manuals are usually written by a technical writer, but in a language understandable to all users of InFocus IN136UST.

A complete InFocus manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual InFocus IN136UST - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the InFocus IN136UST, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the InFocus IN136UST, that we can find in the current document
3. Tips how to use the basic functions of the device InFocus IN136UST - which should help us in our first steps of using InFocus IN136UST
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with InFocus IN136UST
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of InFocus IN136UST in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning InFocus IN136UST?

Use the form below

If you did not solve your problem by using a manual InFocus IN136UST, ask a question using the form below. If a user had a similar problem with InFocus IN136UST it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)