English dropdown-ico

Manual Furuno GP-7000F

52 pages 1.38 mb
Download

Go to site of 52

Summary
  • Furuno GP-7000F - page 1

    www .furuno.co.jp In st all atio n Man ual COLOR GPS/PLO TTER/SOUN DER G P-7 00 0F SAF ETY IN STRUCT IO NS ..... ..... ..... ..... ..... .... ..... .......... ..... .... ..... ..... ..... ..... ... i SYSTEM CON FIGURATION . ..... ..... ..... ..... .... ..... ..... .......... .... ..... ..... ..... ..... .. ii EQUI PMEN T LI STS ...... ..... .... .. ...

  • Furuno GP-7000F - page 2

    The paper used in this manual is elemental chlorine free. ・FURUNO Authorized Distributor/Dealer 9-52 Ashihara-cho, Nishinomiya, 662-8580, JAPAN Telephone : +81-(0)798-65-2111 Fax : +81-(0)798-65-4200 A : AUG 2004 . Printed in Japan All rights reserved. C1 : JUN . 21, 2007 Pub. No. IME-44291-C1 *00014914012* *00014914012* ( HIMA ) GP-7000F * 00014 ...

  • Furuno GP-7000F - page 3

    i SAFETY INSTR UCTIONS WARNING ELECTRICAL SHOCK HAZARD Do not open the equipment unless totally familiar with electrical circuits and service manual. Only qualified personnel should work inside the equipment. Turn off the power at the switchboard before beginning the installation. Fire or electrical shock can result if the power is left on. CAUTION ...

  • Furuno GP-7000F - page 4

    ii SYSTEM CONFIGURA TION TRANSDUCER Speed/Water Temp Sensor (option) Distributor MB-1000* * Required when using 1 kW transducer . Power Source 12-24 VDC : Option : Standard : User Supply ANTENNA UNIT GPA-017 DISPLA Y UNIT GP-7000F How to remo ve the hard cov er Place your thumbs at the center of the cov er , and then lift the cov er while pressing ...

  • Furuno GP-7000F - page 5

    iii EQUIPMEN T LISTS Standa rd su pply *: See list at back o f this manual. Name T y pe Co de No. Qt y Rema rks Displa y U nit GP-7000F - 1 Ante nna Un it GP A -017 - 1 Sys tem also av a ilable with - out ante nna (f or boa ts which al ready hav e a n appro priat e an ten na) Installa tion Material s* CP1 4-0 640 0 00 0-041- 18 3 1 Signa l ca ble a ...

  • Furuno GP-7000F - page 6

    iv Optional equipment Name T ype Code No Qty GPS Antenna GP A-017S 000-040-541 Antenna Cable Set CP20-01700 004-372-1 10 30 m, antenna cable extension CP20-01710 004-372-120 50 m, antenna cable extension Right Angle Antenna Base No.13-QA330 000-803-23 9 For mounting antenna unit L-angle Antenna Base No.13-QA310 000 -803-240 Antenna Base for Rail Mo ...

  • Furuno GP-7000F - page 7

    1 1. INST A LLA TIO N 1.1 Dis play Unit The disp lay un it ma y be m oun te d on a de sk top, ov er he ad o r flus h mo un ted in a co nso le. Mo unting c onsid era tio ns Ch oose a m ou ntin g loca ti on for th e disp lay un it cons ideri ng t he follo wing poin t s: • C hoo se a lo c ation whe re t he cont rols can be eas il y ope rated . • L ...

  • Furuno GP-7000F - page 8

    2 Mounting Desktop, overhead mounting 1. Fix the hanger to the mounting location with fo ur self-tapping screws (5x20). See the outline drawing on page D-1 for comple te mounting dimensions. 2. Loosely screw the knob bolts into the display unit. 3. Set the display unit to the hanger and tigh ten the knob bolts. 4. Attach the hard cover to the displ ...

  • Furuno GP-7000F - page 9

    3 Flush mounting If the thickness of the console is 11-14 mm, use the washer head screws (M4x20) supplied with the installation materials. If it is thicker than those dimensions, th e length of the screws should be the thickness of the console plus 7.3 mm ± 1.5 mm. The length of the threaded portion to b e inserted to the display unit should not e ...

  • Furuno GP-7000F - page 10

    4 1.2 Antenna Unit Refer to the antenna unit outline drawing at the back of this manual for mounting instructions. When selecting a mounting location co nsider the following points: • Select a location ou t of the radar and Inmarsat beams. Those beams will obstruct or preven t reception of the GPS satellite signal. • There should be no interfe ...

  • Furuno GP-7000F - page 11

    5 1.3 T r ansdu cer Insid e -h ull mou ntin g Th e thr u-h ull mo unt t ra nsdu cer (520 -5P SD, 5 20- 5MS D) m ay al so be i nst all ed in si de t he hu ll , f ol- low ing the pr oc ed ure be low . Nece ssa ry tools You wi l l n eed the following tools: • San dpape r (# 100 ) • Silic o ne se ala nt Rem arks on installation • Turn off th e en ...

  • Furuno GP-7000F - page 12

    6 At tachi ng th e trans ducer 1. Clean the tr an sduc er f ace t o r emo ve a ny for eig n ma t eri al. L igh tly rou gh en t he tran sd uce r fac e with # 10 0 s and pape r. Also, ro ughen th e in side of the hul l wher e t he transdu c er is to be mo un ted. 2. W arm the silic on e sea lan t to 40 °C be f ore usag e to s often it. Co at th e tr ...

  • Furuno GP-7000F - page 13

    7 Thru- hul l mount ing Transd ucer m ounti ng loc ation Th e thr u-h ull mo unt t ra nsdu cer (520 -5P SD, 5 20- 5MS D) pr ov ides the bes t pe rf orman ce of al l, sin ce t h e transd uc e r p rotru de s f ro m t he h ull a nd the e ffe ct of a ir bu bb les and t urbu len c e near t he hull ski n is reduc e d. W h en t he bo at h as a k ee l, t h ...

  • Furuno GP-7000F - page 14

    8 Acce pta ble tr ansdu cer moun tin g lo cati ons Suit ab le tra ns duc er mo un ti ng lo cation s  P osition 1/2 to 1/3 of the hull from ster n.  15 to 30 cm off center line (inside first lifting strak es.)  Within the wetted bottom area  Deadrise angle within 15 ° DEEP-V HULL HIGH SPEED-V HULL ...

  • Furuno GP-7000F - page 15

    9 Proc edure f or ins talli ng the t hru-h ull mou nt tr ansducer 1. With the b oat hauled o u t of the water , mark the lo cation chose n fo r mounti ng the tra n sducer on th e b otto m of the hu ll. 2. If th e hull is not l evel withi n 15° in any dir ection, f a iri ng blocks m ade out o f teak shou l d be used betwe e n the transducer a nd hu ...

  • Furuno GP-7000F - page 16

    10 Transom mount transducer The transom mount transducer (525-5PWD) is very common ly employed, usually on relatively small inboard/outboard or outboard boats. Do not use this method on an inboard motor boat be- cause turbulence is created by the propeller ahead o f the transducer. There are two methods of installati on: flush with hull (for flat h ...

  • Furuno GP-7000F - page 17

    11 Installing the transom mount transducer on a deep-V hull This method is employed on deep-V hulls and provides good performance because the effects of air bubbles are minimal. Install the transducer paralle l with water surfa ce; not flush with hull. If the boat is placed on a trailer, care must be taken n ot to damage the transducer when the boa ...

  • Furuno GP-7000F - page 18

    12 Opti on al tr iduc er 525ST -MSD The op tion al t riduc e r 52 5S T-M SD is des i gne d fo r thru -hu ll m oun tin g. F o r how to ins ta ll it , see "t h - ru- hul l m oun ting ” on pag e 7. Triduc e r 525ST-MSD 525ST -PWD The Tra n som Mount Tr ansducer or TR IDUCER ® Mul tisensor wit h I n tegral Release Br a cket 525S T -P WD is m an ...

  • Furuno GP-7000F - page 19

    13 Dril l bit fo r: Brac ke t ho le s: 4 mm , #2 3, or 9/ 6 4" Fiber g lass h u ll: ch amfer bi t (preferre d ), 6 mm, or 1/4 " Tra nso m h ole : 1 9 mm or 3 / 4" (o ptio nal ) Cab le cl amp hol es: 3 mm or 1/8 " Sc rewd riv ers Str aig ht edg e Ma rine seal an t Penc i l Zip-tie s Wa ter-b as e d anti fouli ng p ain t ( m an da ...

  • Furuno GP-7000F - page 20

    14 Insta llation of bracket 1. Cut ou t the ins tal lat io n templ at e sho w n be low . 2. At the se le cted locati o n, posit ion th e template , so the a rro w at th e bottom i s aligned wi th the bott o m edge of the tran so m. Bei n g su r e the tem plat e is p a ral l el to the wat e rli n e, t ape it i n plac e. Warning: A lways we a r safe ...

  • Furuno GP-7000F - page 21

    15 Adjusting 1. Using a straight edge, sight the underside of the sen sor relative to the underside of the hull. The stern of the sensor should be 1-3 mm (1/16-1 / 8") below the bow of the sensor or parallel to the bottom of the hull. Sensor position and transom angle Note: Do not position the bow of the sensor lower than the stern because aer ...

  • Furuno GP-7000F - page 22

    16 5. Using t h e ve r tic a l adju stment sp a ce on the bracket s lots, slide th e sensor up or down to pro- vid e a pr oje ctio n of 3 m m (1 /8") . T ig ht en th e sc re ws. Vert ical a dju s tment an d cab le ro utin g Attachi ng the sensor to the bra cket 1. If the reta ining cover near th e top of the bracket i s closed, open i t b y de ...

  • Furuno GP-7000F - page 23

    17 4. Position the second cable clam p halfway between the first clamp and the ca ble hole. Mark this mounting hole. 5. If a hole has been drilled in the transom, open the appropriate slot in the transom cable cover . Position the cover over the cable wh ere it enters the hull. Mark the two mounting holes. 6. At each of the marked locations, use a ...

  • Furuno GP-7000F - page 24

    18 1. 4 Option al S peed/W ate r T e mperatur e Sensor ST -02MSB, ST -0 2PSB 1. Dry-dock th e b oat. 2. Make a hole of approx. 51 mm diameter i n the mounti ng locati on. 3. Unfasten l ocknut and r e move th e sensor secti on. 4. Apply hig h-grade seala n t to the fl a nge of t he sensor . 5. Pass the se nsor casi n g thr o ugh th e hol e . 6. Face ...

  • Furuno GP-7000F - page 25

    19 2. WIRING The figure below shows the basic wiring scheme. Display unit, rear view Shield White Black Ground ANTENNA UNIT GP A-017 Antenna Cable 10 m MJ-A15A3F0013-035-3A, 3.5 m FROM LEFT PC/NMEA IN: Connection of PC, NMEA device, AIS NMEA 2: Radar, autopilot, video sounder, temperature indicator, etc. NMEA 1: Same as NMEA 2 Speed/W ater T emp Se ...

  • Furuno GP-7000F - page 26

    20 Power source The power source is a 12-24 VDC battery. Be sure the power cable is tightly fastened to the power source and the polarity (plus and minus) is correct. Connect th e white lead to the positive terminal (+) and the black lead to the negative terminal (-). Transducer Connect the transducer to XDR port on the rear of the display unit. If ...

  • Furuno GP-7000F - page 27

    21 Wiring for connection of speed/water te mperature sensor with cable 02S4147 Ground Connect the ground wire to the boat's grou nding bus. If the unit is not grounded, noise may result. If noise is a problem on an FRP vessel, fasten a gr ound plate of 20 cm x 30 cm to the outside of the ship's hull and connect the ground wire there. Use ...

  • Furuno GP-7000F - page 28

    22 Antenna cab le Type s of a ntenna cab les If a long er len gt h of an te nn a cab le is req uire d, us e t he option al an t en na c ab le set , wh ic h is av ail - abl e i n 30 and 50 m le ngth s. Conne cting the antenn a cable If yo u are us in g th e a nt en na ca ble se t, a c oa x ial conne c t er is fi tte d at on e en d of th e c ab le a ...

  • Furuno GP-7000F - page 29

    23 Waterproofing the connector If you are using the extension cabl e, connect the ca ble and then wrap the connector with self- vul- canizing tape and then vinyl tape to waterproof it. Bi nd ends of vinyl tape with cable ties (local sup- ply) to prevent unraveling. How to waterproof the connector ...

  • Furuno GP-7000F - page 30

    24 How to attach N-P-8DFB conne ctor (for extension cable kit) How to attach N-P-8DFB connector Outer Sheath Armor Dimensions in millimeters. Inner Sheath Shield Remov e outer sheath and ar mor by the dimensions shown left. Expose inner sheath and shield by the dimensions shown left. Cut off insulator and core by 10 mm. T wist shield end. Slip on c ...

  • Furuno GP-7000F - page 31

    25 Optional transducer The optional Distributor MB-1000 is required to con nect the optional transducers 50B-6, 50B-6G, 200B-5S, 200B-5S, 50/200-IT. The optional cable assy 02S4089 (Code No. 000-133 -622, 1 m) is required to connect the Distributor. Distributor MB-1000, cover removed Fabricating the transducer cable Fabricate the transducer cable a ...

  • Furuno GP-7000F - page 32

    26 3. ADJUSTMENTS This chapter shows you how to adjust your uni t, from the menu. When choosing item or option from the menu, you may use the [ENTER] knob or the Curso rPad ( ). For sake of brevity the descriptions contained herein use the [ENTER] kno b. 3.1 Choosing Position Dat a Source 1. Press the [MENU] key to show the menu bar. Menu bar 2. Ro ...

  • Furuno GP-7000F - page 33

    27 3. Rotate the [ENTER] knob to choose INPUT/ OUTPUT and then push the [ENTER] knob. INPUT/OUTPUT menu 4. Rotate the [ENTER] knob to choose INTE RNAL GPS SETUP and then push the [ENTER] knob. INTERNAL GPS SETUP menu 5. Rotate the [ENTER] knob to choose INTERNAL GPS and t hen push the [ENTER] knob. 6. Rotate the [ENTER] knob to choose Of f or On an ...

  • Furuno GP-7000F - page 34

    28 3.2 Choo sing Port I/O Form at 1. Press the [ME NU] key to show t h e menu b ar. 2. Rotate the [ENTER] knob to choose A D V ANCED from th e menu bar and then p ush the [ENTER] knob. 3. Rotate the [ENTER] kn o b t o cho o se INPUT/OUTPUT a n d th e n push t he [ENTER] kn ob. 4. Rotate the [ENTER] kn o b t o cho o se approp riate INPUT o r OUTPUT ...

  • Furuno GP-7000F - page 35

    29 Output 1) Rota te the [ENTER] kn o b t o choose approp r ia te option and t hen push th e [ENTER] kn ob . 2) Rota te the [ENTER] kn o b t o choose Of f or On as a ppro p riat e an d then p ush the [ENTER] knob fo llowed by W . 6. Repeat ste p 5 to set up other por ts. 7. Press the [ ME NU ] key t o clos e all op en wind ows an d er ase t he menu ...

  • Furuno GP-7000F - page 36

    30 3.3 Ech o Sounder Set tings Sett ing t ransduc er mod el, out put po wer The G P -70 00F is pre s et to us e a 600 W tra ns d ucer (5 20 -5P SD , 52 5-5 PW D , 52 0-5 M SD ). F or a 1 kW t ra nsd uc er , follo w the pr oced ure b elo w . Not e that th e o ption al D istr ibut or MB- 100 0 an d ca ble assy. 0 2 S4089 ar e necessary i n order t o ...

  • Furuno GP-7000F - page 37

    31 Ca libr ati ng spe ed/ wate r temp erat ur e sensor , se ttin g dr aft The optio na l s peed/ wa te r tem pe ratu re se ns or may be ca libr ated as below to co mp ens a te for er - ror. If you requi r e depth fr o m the sea surf a ce (rather than the tra n sdu ce r), set it with "DRAFT SET- UP." For ei ther sensor ca librati o n o r d ...

  • Furuno GP-7000F - page 38

    32 8. Rotate the [ENTER] knob to set digit and push the [ENTER] knob. T o clear a line of data, press the [CLR FLD] soft key (one o f the keys below the screen). Setting range Draft setup: -20 - +39.9 (ft) S peed calibration: -50 - +50 (%) T emp calibration: -50 - +5 ( ° F) Acoustic speed calibration: -50 - +50 (ms) 9. Set other digits as you did ...

  • Furuno GP-7000F - page 39

    33 3. 5 Cal ibrating NMEA D epth, S peed and W ater T em perature Dat a NMEA sp eed, dept h and water t emper at ure data may b e c orrec ted f ro m th e GP-70 00F if the y ca n- not be do ne from the e qu ipme nt that outp uts the da t a. Ente r a m in us va lue if the ac tua l va lue is lower than the NMEA data , or a plu s value i f the actual v ...

  • Furuno GP-7000F - page 40

    34 3.6 W aypoin t, Route Forma t You may tr ansf er wayp oin t and ro ute dat a t o an other GP- 700 0 ser ies un it o r a PC i n St anda rd o r Furuno fo rmat, via the NMEA1 port, NM EA2 port or PC NMEA IN po rt. 1. Press the [ME NU] key to show t h e menu b ar. 2. Rotate the [ENTER] knob to choose A D V ANCED from th e menu bar and then p ush the ...

  • Furuno GP-7000F - page 41

    35 3.8 Primary , Secondary Unit (C-link) The C-link feature, available when seve ral GP -7000 series units are interconnected via NMEA ports or PC/NMEA IN ports (see the illustration below), lets you duplicate on secondary station s the destination set at th e primary station. With this feature active destin ation may only be set from the primary s ...

  • Furuno GP-7000F - page 42

    NAME OUTLINE Q'TY DESCRIPTION/CODE № ＰＡＣＫＩＮＧ　ＬＩＳＴ 14CR-X-9851 -12 GP-7000/F-E-C-017,GP-7000/F-E-N-017 1/1 NAME OUTLINE Q'TY DESCRIPTION/CODE № ユニット UNIT 空中線部 ANTEN NA UNIT 1 GPA- 017 000-041-403-00 指示器 DISPL AY UNIT 1 ** GP-7 000-E-C 000-041-184-00 予備品 SPARE PARTS SP14-03201 ﾋｭ? ...

  • Furuno GP-7000F - page 43

    NAME OUTLINE Q'TY DESCRIPTION/CODE № ＰＡＣＫＩＮＧ　ＬＩＳＴ 14CR-X-9852 -13 GP-7000/F-E-C,GP-7000/F-E-N 1/1 NAME OUTLINE Q'TY DESCRIPTION/CODE № ユニット UNIT 指示器 DISPL AY UNIT 1 ** GP-7 000-E-C 000-041-184-00 予備品 SPARE PARTS SP14-03201 ﾋｭｰｽﾞ FUSE 1 FGBO -A 3A AC 125V 000-549-063-00 FGB0 -A 125V ...

  • Furuno GP-7000F - page 44

    Y. Hatai D-1 ...

  • Furuno GP-7000F - page 45

    Y. Hatai D-2 ...

  • Furuno GP-7000F - page 46

    Y . Hatai hatai 2005.12.19 11:57:12 +09'00' D-3 ...

  • Furuno GP-7000F - page 47

    Mar,27'07 R.Esumi D-4 ...

  • Furuno GP-7000F - page 48

    Feb. 17, '03 D-5 ...

  • Furuno GP-7000F - page 49

    D-6 ...

  • Furuno GP-7000F - page 50

    D-7 ...

  • Furuno GP-7000F - page 51

    Mar. 03 '05 D-8 ...

  • Furuno GP-7000F - page 52

    12 4 3 B A C NOTE 注記 ＊２）オプション。 ＊１）造船所手配。 ＊３）コネクタは現地にて取付け。 *1 GND *3. ATTACH CONNECTOR LOCALLY. NAME 名称 TITLE kg MASS DWG No. SCALE APPROVED CHECKED DRAWN GP-7000F カラーGPSプロッタ魚探 COLOR GPS PLOTTER/SOUNDER INTERCONNECTION DIAGRAM 相互結線図 E. MIYOSHI 10m ...

Manufacturer Furuno Category Marine GPS System

Documents that we receive from a manufacturer of a Furuno GP-7000F can be divided into several groups. They are, among others:
- Furuno technical drawings
- GP-7000F manuals
- Furuno product data sheets
- information booklets
- or energy labels Furuno GP-7000F
All of them are important, but the most important information from the point of view of use of the device are in the user manual Furuno GP-7000F.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Furuno GP-7000F, service manual, brief instructions and user manuals Furuno GP-7000F. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Furuno GP-7000F.

Similar manuals

A complete manual for the device Furuno GP-7000F, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Furuno GP-7000F by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Furuno GP-7000F.

A complete Furuno manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Furuno GP-7000F - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Furuno GP-7000F, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Furuno GP-7000F, that we can find in the current document
3. Tips how to use the basic functions of the device Furuno GP-7000F - which should help us in our first steps of using Furuno GP-7000F
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Furuno GP-7000F
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Furuno GP-7000F in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Furuno GP-7000F?

Use the form below

If you did not solve your problem by using a manual Furuno GP-7000F, ask a question using the form below. If a user had a similar problem with Furuno GP-7000F it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)