English dropdown-ico

Manual Hobart LXiC ML-130016

24 pages 1.53 mb
Download

Go to site of 24

Summary
  • Hobart LXiC ML-130016 - page 1

    701 S. RIDGE AVENUE TROY, OHIO 45374-0001 937 332-3000 www.hobartcorp.com N S T R U C T I O N S I LXi SERIES DISHW ASHER MODELS LX iC ML-130016 LX iH ML-130017 LX iGC ML-130018 LX iGH ML-130019 FORM 34779 Rev. B (Sept. 2005) LXi SERIES DISHWASHER ...

  • Hobart LXiC ML-130016 - page 2

    – 2 – © HOBART CORPORATION, 2003 ...

  • Hobart LXiC ML-130016 - page 3

    – 3 – TABLE OF CONTENTS GENERAL ............................................................................................................................................ 4 INSTALLATION ................................................................................................................................... 5 Unpacking .............. ...

  • Hobart LXiC ML-130016 - page 4

    – 4 – Installation, Operation and Care of LXi SERIES DISHW ASHERS SA VE THESE INSTRUCTIONS GENERAL The LXi Series dishwashers are fully automatic, front-loading dishwashing machines that are capable of 30 racks per hour. All LXi Series dishwashers shut down automatically 4 hours after last use to conserve energy. All LXiH and LXiGH dishwashers ...

  • Hobart LXiC ML-130016 - page 5

    – 5 – INST ALLA TION UNPACKING Immediately after unpacking the dishwasher, check for possible shipping damage. If this machine is found to be damaged, save packaging material and contact the carrier within 15 days of delivery. LOCATION Prior to installation, verify that the electrical supply agrees with the specifications on the machine data pl ...

  • Hobart LXiC ML-130016 - page 6

    – 6 – Water Supply A water hammer arrestor (meeting ASSE-1010 Standard or equivalent) should be installed (supplied by others) in the common water supply line at the service connection. Water must be proper hardness. Higher hardness may cause excessive formation of lime scale. The plumber connecting this machine is responsible for making certai ...

  • Hobart LXiC ML-130016 - page 7

    – 7 – ELECTRICAL CONNECTION WARNING : ELECTRICAL AND GROUNDING CONNECTIONS MUST COMPLY WITH THE APPLICABLE PORTIONS OF THE NATIONAL ELECTRICAL CODE AND/OR OTHER LOCAL ELECTRICAL CODES. WARNING: DISCONNECT THE ELECTRICAL POWER TO THE MACHINE AND FOLLOW LOCKOUT / TAGOUT PROCEDURES. ELECTRICAL DATA Complied in accordance with the National Electric ...

  • Hobart LXiC ML-130016 - page 8

    – 8 – Connection Method 1. Remove the cover plate at the upper right in the back of the machine (Fig. 1). A hole for 1" trade size conduit is supplied in the cover plate. Fig. 1 Fig. 2 2. Remove the two screws (Fig. 2) securing the controls drawer and open it fully. 3. Install 1" trade conduit and fitting to the cover plate. A 90 degr ...

  • Hobart LXiC ML-130016 - page 9

    – 9 – OPERATOR PROGRAMMING MODE The Operator Programming mode allows changes to be made from factory settings to the chemical pumps’ operation. This includes the Detergent and Rinse Aid pumps, but does not apply to the Sanitizer pump on the LXiC and LXiGC models. The Detergent and/or Rinse Aid pumps can be turned off by entering this programm ...

  • Hobart LXiC ML-130016 - page 10

    – 10 – INSTALLATION DIAGRAM (LXiC & LXiH) W ARNING: REQUIRED FLOWING WA TER PRESSURE TO THE DISHMACHINE IS 20 ± 5 PSIG. IF PRESSURES HIGHER THAN 25 PSIG ARE PRESENT , A PRESSURE REGULA TING V AL VE MUST BE INST ALLED IN THE WA TER LINE TO THE DISHMACHINE (BY OTHERS). IMPORT ANT : THE SODIUM HYPOCHLORITE (LIQUID BLEACH) CONT AINER SHOULD BE ...

  • Hobart LXiC ML-130016 - page 11

    – 11 – INSTALLATION DIAGRAM (LXiGC & LXiGH) CONNECTION INFORMA TION (AFF = ABOVE FINISHED FLOOR) LEGEND E1 ELECTRICAL CONNECTION: 1-3/8" DIA. HOLE FOR 1" TRADE SIZE CONDUIT ; 31-3/4" AFF . P1 SINGLE FILL AND RINSE CONNECTION: 3/4" FEMALE GARDEN HOSE FITTING ON 6' LONG HOSE SUPPLIED WITH MACHINE; 140 ° F W A TER MIN ...

  • Hobart LXiC ML-130016 - page 12

    – 12 – CHEMICAL SANITIZER (LXiC AND LXiGC) CAUTION: Items such as pewter, aluminum and silver will be attacked by sodium hypochlorite (bleach). Therefore, chemical-sanitizing dishwashers should not be used to wash such items. On model LXiC only, the chemical sanitizer pump is factory-set for use with 6% sodium hypochlorite solution. If 8.40% so ...

  • Hobart LXiC ML-130016 - page 13

    – 13 – OPERATING THE LXi DISHWASHER S I H T O D S W O H S Y A L P S I D S K R A M E R . N O s s e r P . r e b m u n l e d o M s i h T . k c e h c - f l e s s m r o f r e p r e h s a w h s i D . s d n o c e s 0 1 - 5 s e k a t e r u t a r e p m e t p m u s d n a t i l L L I F s i e n i h c a m n e h w d e y a l p s i d . g n i l l i f l l i F s ...

  • Hobart LXiC ML-130016 - page 14

    – 14 – DIAGNOSTIC MESSAGES In the event of a problem with a temperature probe, the display will flash P1, P2 or P3 every second. The respective heaters will shut down. Other functions will continue to operate normally. Contact your local Hobart Service Office. Drain and fill error messages are displayed as E0, E1, E2, E3, E4, E5, E6 or E7. In a ...

  • Hobart LXiC ML-130016 - page 15

    – 15 – PREPARATION Make sure the coarse (Fig. 7) and fine (Fig. 8) strainers are in place and free of debris. Check both wash arms and rinse arms to make sure they spin freely and are not clogged. Fig. 7 Fig. 8 Dishes must be scraped and/or rinsed to remove food particles and other debris. Never use steel wool on ware to be loaded into the dish ...

  • Hobart LXiC ML-130016 - page 16

    – 16 – DO'S AND DON'TS FOR YOUR NEW HOBART DISHWASHER DO assure proper water hardness. DO prescrape dishes thoroughly. DO use only detergents recommended by your chemical professional. DO, at the end of the day, thoroughly cleanse the machine, rinse and dry. (Leave door open.) DO closely follow your chemical professional's prescr ...

  • Hobart LXiC ML-130016 - page 17

    – 17 – CLEANING This machine must be cleaned at least once each working day. Use only products formulated to be safe on stainless steel. 1. Press OFF. The machine will drain. When the display is no longer lit, open the door and remove any debris from the bottom of the tank. Do not allow food soil to accumulate on the tank bottom. 2. Remove the ...

  • Hobart LXiC ML-130016 - page 18

    – 18 – PRIMING CHEMICAL PUMPS When a chemical becomes empty, the priming operation starts automatically the next time the machine is turned on or a wash cycle is started. This feature is only supported on machines with the chemical sense board installed and where CHEMICAL SENSING is enabled. Note that the initial prime time for all pumps (Deter ...

  • Hobart LXiC ML-130016 - page 19

    – 19 – MAINTENANCE DELIMING WARNING: DELIMING SOLUTION, RINSE AGENTS OR ANY OTHER KIND OF ACID MUST NOT COME IN CONTACT WITH BLEACH OR RINSE SOLUTION CONTAINING BLEACH USED IN CHEMICAL-SANITIZING MACHINES. MIXING MAY CAUSE HAZARDOUS GAS TO FORM. THIS ENTIRE PROCEDURE MUST BE FOLLOWED STEP BY STEP FOR SAFE AND SATISFACTORY RESULTS. CAUTION: Do n ...

  • Hobart LXiC ML-130016 - page 20

    – 20 – TROUBLESHOOTING This section outlines various symptoms and possible causes that may be encountered in the event of abnormal machine operation. If symptoms persist after possible causes have been checked, service may be required. Symptom Possible Causes No machine operation 1. Machine OFF - turn machine ON. (no display). 2. Blown fuse or ...

  • Hobart LXiC ML-130016 - page 21

    – 21 – Symptom Possible Causes Unexpected results on 1. Etching - usually caused by any combination of high dishes. temperatures, soft water, soft glass or high alkaline washing solutions. 2. Tarnishing - avoid washing silver, silver plates and pewter in chemical-sanitizing machines. 3. Pitting - stainless steel may pit with lengthy contact of ...

  • Hobart LXiC ML-130016 - page 22

    – 22 – Symptom Possible Causes Machine fills too high or 1. Machine not level - see LEVELING in this manual. leaks from door. 2. Fill solenoid valve leaking - turn the dishwasher OFF; if water (Display shows CL/Pr.) continues to come in, contact your local Hobart Service Office. 3. Clean water level probes. (See Cleaning.) Machine will not drai ...

  • Hobart LXiC ML-130016 - page 23

    – 23 – NOTES ...

  • Hobart LXiC ML-130016 - page 24

    – 24 – FORM 34779 Rev. B (Sept. 2005) PRINTED in U.S.A. NOTES ...

Manufacturer Hobart Category Dishwasher

Documents that we receive from a manufacturer of a Hobart LXiC ML-130016 can be divided into several groups. They are, among others:
- Hobart technical drawings
- LXiC ML-130016 manuals
- Hobart product data sheets
- information booklets
- or energy labels Hobart LXiC ML-130016
All of them are important, but the most important information from the point of view of use of the device are in the user manual Hobart LXiC ML-130016.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Hobart LXiC ML-130016, service manual, brief instructions and user manuals Hobart LXiC ML-130016. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Hobart LXiC ML-130016.

Similar manuals

A complete manual for the device Hobart LXiC ML-130016, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Hobart LXiC ML-130016 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Hobart LXiC ML-130016.

A complete Hobart manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Hobart LXiC ML-130016 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Hobart LXiC ML-130016, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Hobart LXiC ML-130016, that we can find in the current document
3. Tips how to use the basic functions of the device Hobart LXiC ML-130016 - which should help us in our first steps of using Hobart LXiC ML-130016
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Hobart LXiC ML-130016
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Hobart LXiC ML-130016 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Hobart LXiC ML-130016?

Use the form below

If you did not solve your problem by using a manual Hobart LXiC ML-130016, ask a question using the form below. If a user had a similar problem with Hobart LXiC ML-130016 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)