Manual Hoover DYN D8P

40 pages 1.57 mb
Download

Go to site of 40

Summary
  • Hoover DYN D8P - page 1

    Instruction Book Instructions for installation and use ...

  • Hoover DYN D8P - page 2

    ...

  • Hoover DYN D8P - page 3

    ...

  • Hoover DYN D8P - page 4

    8 kg 0.05 ÷ 0.8 MPa 85 cm 60 cm 52 cm ...

  • Hoover DYN D8P - page 5

    ...

  • Hoover DYN D8P - page 6

    ...

  • Hoover DYN D8P - page 7

    ...

  • Hoover DYN D8P - page 8

    Unpacking the Product Remove the machine from its packaging close to the final location of the machine. Step 1 . Remove all outer packaging from the machine. Check there is no damage to the machine before continuing the installation process. Step 2 . Carefully cut through the hose-retaining clip at the rear of the machine, taking care not to cut t ...

  • Hoover DYN D8P - page 9

    Unpacking the Product Remove the machine from its packaging close to the final location of the machine. Step 1 . Remove all outer packaging from the machine. Check there is no damage to the machine before continuing the installation process. Step 2 . Carefully cut through the hose-retaining clip at the rear of the machine, taking care not to cut t ...

  • Hoover DYN D8P - page 10

    W a ter Suppl y This machine should only be connected to a cold-water supply . The cold-water pressure should be between 0.5 and 8 bar (0.05-0.8 Mpa). Do not connect the machine to a single outlet instantaneous water heater . Before connecting the fill hose, check that the water is running from the water supply tap to be used. Let the water flow ...

  • Hoover DYN D8P - page 11

    W a ter Suppl y This machine should only be connected to a cold-water supply . The cold-water pressure should be between 0.5 and 8 bar (0.05-0.8 Mpa). Do not connect the machine to a single outlet instantaneous water heater . Before connecting the fill hose, check that the water is running from the water supply tap to be used. Let the water flow ...

  • Hoover DYN D8P - page 12

    Connecting the drainage pipe This machine must be connected in accordance with the water supply regulations. W ater bylaws prohibit connection to a sur face water drain. Decide which plumbing option suits you best then follow the instructions below: Option 1 - W aste pipe connection (waste trap) Fit the hooked end support to the outlet pipe and pos ...

  • Hoover DYN D8P - page 13

    Connecting the drainage pipe This machine must be connected in accordance with the water supply regulations. W ater bylaws prohibit connection to a sur face water drain. Decide which plumbing option suits you best then follow the instructions below: Option 1 - W aste pipe connection (waste trap) Fit the hooked end support to the outlet pipe and pos ...

  • Hoover DYN D8P - page 14

    Description of the Machine The Hoover washing machine details are indicated below: Step 5 . Switch off the machine at the end of the cycle by tur ning the Programme Selector to the OFF position. Step 6 . Select the spin programme and press the Start Pause button to star t the machine. If the machine takes longer than one minute to empty check the d ...

  • Hoover DYN D8P - page 15

    Description of the Machine The Hoover washing machine details are indicated below: Step 5 . Switch off the machine at the end of the cycle by tur ning the Programme Selector to the OFF position. Step 6 . Select the spin programme and press the Start Pause button to star t the machine. If the machine takes longer than one minute to empty check the d ...

  • Hoover DYN D8P - page 16

    The Control P anel T urning the Machine On T urning the Programme Selector to your chosen programme will turn the machine on. The Programme Selector must be returned to the OFF position between each wash cycle in order to reset the controls. Star t Pause Button ST AR T After selecting the programme and the required options press the Start Pause but ...

  • Hoover DYN D8P - page 17

    The Control P anel T urning the Machine On T urning the Programme Selector to your chosen programme will turn the machine on. The Programme Selector must be returned to the OFF position between each wash cycle in order to reset the controls. Star t Pause Button ST AR T After selecting the programme and the required options press the Start Pause but ...

  • Hoover DYN D8P - page 18

    Spin Speed When a programme is selected the maximum spin speed allowed for that programme appears on the display . Pressing the Spin Speed button will reduce the speed by 100rpm each time the button is pressed. The minimum speed is 400rpm, or continuing to press the button will eliminate the final spin completely . Delay Star t This indicator show ...

  • Hoover DYN D8P - page 19

    Spin Speed When a programme is selected the maximum spin speed allowed for that programme appears on the display . Pressing the Spin Speed button will reduce the speed by 100rpm each time the button is pressed. The minimum speed is 400rpm, or continuing to press the button will eliminate the final spin completely . Delay Star t This indicator show ...

  • Hoover DYN D8P - page 20

    Automa tic Fea tures KG Mode (Half Load) Available on the Cottons and Synthetics cycles, the intelligent sensor adjusts the water level and programme length throughout each phase of the cycle according to how much laundr y you load into the machine. The KG Mode indicator will light up when the intelligent sensor is weighing the laundr y . The washi ...

  • Hoover DYN D8P - page 21

    Automa tic Fea tures KG Mode (Half Load) Available on the Cottons and Synthetics cycles, the intelligent sensor adjusts the water level and programme length throughout each phase of the cycle according to how much laundr y you load into the machine. The KG Mode indicator will light up when the intelligent sensor is weighing the laundr y . The washi ...

  • Hoover DYN D8P - page 22

    Programme Descriptions For handling the various types of fabric and their level of dirtiness in your laundr y the washing machine has different programme groups according to type of wash, temperature, spin speed and duration (see Programme Guide). Once the programme is selected, the intelligent sensor will weigh the laundr y using the KG Mode and a ...

  • Hoover DYN D8P - page 23

    Programme Descriptions For handling the various types of fabric and their level of dirtiness in your laundr y the washing machine has different programme groups according to type of wash, temperature, spin speed and duration (see Programme Guide). Once the programme is selected, the intelligent sensor will weigh the laundr y using the KG Mode and a ...

  • Hoover DYN D8P - page 24

    Programme Guide 24 25 Programme Fabric T ype W ater T emp Recommended (C°) W ater T emp MAX (C°) Spin Speed MAX (RPM) Max Load Size (kg) Cottons, Colourfast and linen Cottons, Non- fast Coloureds, mixed fabrics Mixed fabrics and synthetics Delicate fabrics - - - Silk and “Machine washable wool” garments Lightly dirty cottons and synthetics Co ...

  • Hoover DYN D8P - page 25

    Programme Guide 24 25 Programme Fabric T ype W ater T emp Recommended (C°) W ater T emp MAX (C°) Spin Speed MAX (RPM) Max Load Size (kg) Cottons, Colourfast and linen Cottons, Non- fast Coloureds, mixed fabrics Mixed fabrics and synthetics Delicate fabrics - - - Silk and “Machine washable wool” garments Lightly dirty cottons and synthetics Co ...

  • Hoover DYN D8P - page 26

    Refer to the programme guide ( pag.24) ** ST ANDARD COTTON PROGRAMMES ACCORDING TO (EU) No 1015 /2010 and No 1061/2010 COTTON PROGRAMME with a temperatur e of 60°C COTTON PROGRAMME with a temperatur e of 40°C These programmes are suita ble to clean normally soiled cotton laundry and they are the most efficient programmes in terms of combined ene ...

  • Hoover DYN D8P - page 27

    Refer to the programme guide ( pag.24) ** ST ANDARD COTTON PROGRAMMES ACCORDING TO (EU) No 1015 /2010 and No 1061/2010 COTTON PROGRAMME with a temperatu re of 60°C COTTON PROGRAMME with a temperatu re of 40°C These programmes are suit able to clean normally soiled cotton laundry and they are the most efficient programmes in terms of combined ene ...

  • Hoover DYN D8P - page 28

    Laundry Items to avoid W e recommend that you do not wash under wired bras in the machine. Should the wires become detached they could cause damage to your clothes and the machine. If the wash care label states that the bra is machine washable then we advise placing it in a wash bag. Recommendations Always follow the wash care labelling on the garm ...

  • Hoover DYN D8P - page 29

    Laundry Items to avoid W e recommend that you do not wash under wired bras in the machine. Should the wires become detached they could cause damage to your clothes and the machine. If the wash care label states that the bra is machine washable then we advise placing it in a wash bag. Recommendations Always follow the wash care labelling on the garm ...

  • Hoover DYN D8P - page 30

    the wash cycle, the KG Mode will weigh the clothes and update the wash time remaining on the display ever y five seconds until the weight has been determined. In some programs in the initial phase of the cycle there are planned spin sequences to ensure optimal wash results. Do not tr y to open the door when the door locked indicator is on, nor ope ...

  • Hoover DYN D8P - page 31

    the wash cycle, the KG Mode will weigh the clothes and update the wash time remaining on the display ever y five seconds until the weight has been determined. In some programs in the initial phase of the cycle there are planned spin sequences to ensure optimal wash results. Do not tr y to open the door when the door locked indicator is on, nor ope ...

  • Hoover DYN D8P - page 32

    Step 4 . T urn the filter anti-clockwise until it stops in the ver tical position. Remove the filter and clean. Step 5 . Replace the filter and turn in a clockwise direction until locked in position. Replace the stopper in the hose and close the filter cover . W e recommend that the filter be cleaned frequently , at least once a month. Mainten ...

  • Hoover DYN D8P - page 33

    Step 4 . T urn the filter anti-clockwise until it stops in the ver tical position. Remove the filter and clean. Step 5 . Replace the filter and turn in a clockwise direction until locked in position. Replace the stopper in the hose and close the filter cover . W e recommend that the filter be cleaned frequently , at least once a month. Mainten ...

  • Hoover DYN D8P - page 34

    W ater on the floor around the washing machine... ● Is the fill hose tightened? If so, replace the rubber washers and re-tighten. ● Is the standpipe or the household drain blocked? If so, clear the blockage yourself or call a plumber . ● Is there clothing or dirt between the door gasket and the door glass? Ensure that the door glass and gas ...

  • Hoover DYN D8P - page 35

    W ater on the floor around the washing machine... ● Is the fill hose tightened? If so, replace the rubber washers and re-tighten. ● Is the standpipe or the household drain blocked? If so, clear the blockage yourself or call a plumber . ● Is there clothing or dirt between the door gasket and the door glass? Ensure that the door glass and gas ...

  • Hoover DYN D8P - page 36

    Power Failure If there is a power failure the wash cycle will be interrupted, and the wash programme and functions will be suspended. When the power is restored, the wash programme and functions will re-start from the same point and complete the programme. During a power failure the water can be drained and the load can be removed from the machine ...

  • Hoover DYN D8P - page 37

    Power Failure If there is a power failure the wash cycle will be interrupted, and the wash programme and functions will be suspended. When the power is restored, the wash programme and functions will re-start from the same point and complete the programme. During a power failure the water can be drained and the load can be removed from the machine ...

  • Hoover DYN D8P - page 38

    The guarantee excludes: ● Any faults which occur due to bad installation or misuse of the machine. ● Repair of, or interference with, the machine by any person not authorised by the manufacturer . ● Any parts which are fitted to the machine that are not original manufacturer’ s parts. ● Non-domestic use of the machine. ● Operation at i ...

  • Hoover DYN D8P - page 39

    The guarantee excludes: ● Any faults which occur due to bad installation or misuse of the machine. ● Repair of, or interference with, the machine by any person not authorised by the manufacturer . ● Any parts which are fitted to the machine that are not original manufacturer’ s parts. ● Non-domestic use of the machine. ● Operation at i ...

  • Hoover DYN D8P - page 40

    13.02 - 41038569 - Canon Italia - Business Services Channel - Printed in Italy - Imprimé en Italie ...

Manufacturer Hoover Category Washer

Documents that we receive from a manufacturer of a Hoover DYN D8P can be divided into several groups. They are, among others:
- Hoover technical drawings
- DYN D8P manuals
- Hoover product data sheets
- information booklets
- or energy labels Hoover DYN D8P
All of them are important, but the most important information from the point of view of use of the device are in the user manual Hoover DYN D8P.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Hoover DYN D8P, service manual, brief instructions and user manuals Hoover DYN D8P. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Hoover DYN D8P.

Similar manuals

A complete manual for the device Hoover DYN D8P, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Hoover DYN D8P by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Hoover DYN D8P.

A complete Hoover manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Hoover DYN D8P - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Hoover DYN D8P, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Hoover DYN D8P, that we can find in the current document
3. Tips how to use the basic functions of the device Hoover DYN D8P - which should help us in our first steps of using Hoover DYN D8P
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Hoover DYN D8P
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Hoover DYN D8P in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Hoover DYN D8P?

Use the form below

If you did not solve your problem by using a manual Hoover DYN D8P, ask a question using the form below. If a user had a similar problem with Hoover DYN D8P it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)