English dropdown-ico

Manual Sea Frost Bait Freezer

11 pages 0.39 mb
Download

Go to site of 11

Summary
  • Sea Frost Bait Freezer - page 1

    1 372 ROUTE 4 BARRINGTON, NH 03825 USA TEL (603) 868-5720 FAX (603) 868-1040 1-800-435-6708 E-Mail:sales@seafrost.com www.seafrost.com SEA FROST BAIT FREEZER BF1 ~ BF2 ~ BF3 220-VOLT Pre-charged DESCRIPTION The Sea Frost Freezer system consists of se veral parts: The cold plates or wrapped box liner (hidden cooling coils), a refrigerant control val ...

  • Sea Frost Bait Freezer - page 2

    2 CONDENSING UNIT LOCATION AND MOUNTING Air Cooled The design of the Bait Freezer (BF) allo ws the air-cooled condensing unit to be placed in an enclosed space such as a locker or engine room. Mount the unit level with the compressor at the bottom. The unit may be bulkhead or platform mounted. Rubber Wellnut inserts ar e installed on the bottom and ...

  • Sea Frost Bait Freezer - page 3

    3 EVAPORATOR PLATE INSTALLATION Mount the plates on opposite walls as high as possible to take advantage of thermal convection. Install the plates with the Wellnut, spacers and screws provided. The plate(s) mounts with a Wellnut expandable neoprene blind hole fastener. A template or the plate itself should be used to locate the mounting holes. Dril ...

  • Sea Frost Bait Freezer - page 4

    4 EXPANSION VALVE The expansion valve/ liquid line/drier connects to one of the plate fittings and at the discharge fitting on the compressor section. After assembly externally mounted, valves will need to be insulated to prevent frost and sweating. Installers Set up The constant pressure valve sets the refr igerant boiling point. The pressure sett ...

  • Sea Frost Bait Freezer - page 5

    5 Installing a Jumper If installing a multi plate system, use the jumper to connect the remaining tube on the first plate to either tube on the second plate. Installing the Return Line Connect a return line to the remaining tube. This return line connects to the compressor. Support the tubing every 18 inches as nec essary with mountable tie wraps a ...

  • Sea Frost Bait Freezer - page 6

    6 Thermostat Operation The thermostat is pre-set and locked at t he factory. When locked the keypad is disabled and changes to the settings cannot be made. To change the settings the lockout switch must be placed in the unlock position. To access the lockout switch: 1. Switch off the power. 2. Remove the four screws and cover. 3. Slide the lockout ...

  • Sea Frost Bait Freezer - page 7

    7 220-VOLT CIRCUIT A separate 10-amp breaker is required for the 220-volt supply. This circuit powers the thermostat through a built in transformer . For operation, it is necessary to have power at all times. RE-CHARGING OR ADDING REFRIGERANT Adding refrigerant will not change the suction (l ow) side pressure. Do not charge more than 12 oz of R-134 ...

  • Sea Frost Bait Freezer - page 8

    8 WARNING: A clear sight glass can also indicate a completely EMPTY system. Anytime the compressor is started, white foam should appear in the sight glass indicating that the refrigerant is present. This foam may disappear quite quickly but, IF NO FOAM IS EVIDENT and the system is not cooling, the system is empty. DO NOT OPERATE THE SYSTEM in this ...

  • Sea Frost Bait Freezer - page 9

    9 DEFROSTING The unit will require defrosting from time to time as the frost layer builds up. Allowing the unit to warm above freezing is one method of defrosting. Warm water or a hair dryer is also a quick method. Plates can be scraped with a spatula or ice scraper to remove excessive frost build up. Bait Freezer Specifications BF 1 BF 2 BF 3 Amp ...

  • Sea Frost Bait Freezer - page 10

    10 ...

  • Sea Frost Bait Freezer - page 11

    11 ...

Manufacturer Sea Frost Category Freezer

Documents that we receive from a manufacturer of a Sea Frost Bait Freezer can be divided into several groups. They are, among others:
- Sea Frost technical drawings
- Bait Freezer manuals
- Sea Frost product data sheets
- information booklets
- or energy labels Sea Frost Bait Freezer
All of them are important, but the most important information from the point of view of use of the device are in the user manual Sea Frost Bait Freezer.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Sea Frost Bait Freezer, service manual, brief instructions and user manuals Sea Frost Bait Freezer. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Sea Frost Bait Freezer.

Similar manuals

A complete manual for the device Sea Frost Bait Freezer, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Sea Frost Bait Freezer by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Sea Frost Bait Freezer.

A complete Sea Frost manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Sea Frost Bait Freezer - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Sea Frost Bait Freezer, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Sea Frost Bait Freezer, that we can find in the current document
3. Tips how to use the basic functions of the device Sea Frost Bait Freezer - which should help us in our first steps of using Sea Frost Bait Freezer
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Sea Frost Bait Freezer
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Sea Frost Bait Freezer in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Sea Frost Bait Freezer?

Use the form below

If you did not solve your problem by using a manual Sea Frost Bait Freezer, ask a question using the form below. If a user had a similar problem with Sea Frost Bait Freezer it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)