English dropdown-ico

Manual Global Machinery Company POL1450

16 pages 0.25 mb
Download

Go to site of 16

Summary
  • Global Machinery Company POL1450 - page 1

    POL1450 030901 Ed8 DR ...

  • Global Machinery Company POL1450 - page 2

    Contents W arranty 2 Introduction 3 Environment al protection 3 Description of s ymbols 3 Specifications 3 Safety instructions 4 Additional safety rules f or sanders 5 Additional safety rules f or angle grinders 6 Additional safety rules f or polishers 7 Accessories 7 Unpacking 7 Know y our product 8 Setting up 9 Operation in grinder mode 9 Operati ...

  • Global Machinery Company POL1450 - page 3

    Description of s ymbols The rating plate on your tool may show symbols. These represent important information about the product or instructions on its use . Wear hearing protection. Wear eye protection. Wear breathing protection. Double insulated for additional protection. Conforms to relevant standards f or electromagnetic compatibility. Specifica ...

  • Global Machinery Company POL1450 - page 4

    Safety instructions The tool must be used only for the prescribed purpose . Any uses other than those mentioned in this manual will be considered a case of misuse . The user and not the manufacturer shall be liable f or any damage or injury resulting from such cases of misuse . T o use this tool properly , you must observe the safety regulations, t ...

  • Global Machinery Company POL1450 - page 5

    9. Connect dust extr action equipment. If devices are provided for the connection o f dust extraction and collection facilities , ensure that these are connected and properly used. 10. Do not abuse the po wer cor d. Never pull the cord to disconnect the tool from the power point. Keep the cord away from heat, oil and sharp edges. 11. Secur e the wo ...

  • Global Machinery Company POL1450 - page 6

    6 • Check the disc before mounting it into the angle grinder . Check by striking it with a wooden handle whilst balancing the disc on your finger . Listen for the ring and do not use if dull, as the disc may be cracked. • When the disc is installed, run it for at least one minute to ensure that it does not have a fault. It is always advisable t ...

  • Global Machinery Company POL1450 - page 7

    • When sanding wood, always connect the dust bag or use a dust extraction system. • Before using the sander with metal, always remove the dust bag from the outlet as sparks may ignite the dust or the bag. • Do not continue to use worn, torn or heavily clogged sanding discs. • Do not touch the moving sanding disc. • Ensure that you have re ...

  • Global Machinery Company POL1450 - page 8

    Know y our product Before using the polisher , familiarise yourself with all the operating features and safety requirements. Use the tool and accessories only for the applications intended. All other applications are expressly ruled out. 1. Motor housing 2. Spindle lock button 3. V ariable speed dial 4. Rear handle 5. Soft grip 6. Mounting points f ...

  • Global Machinery Company POL1450 - page 9

    Setting up Multi position front handle Screw the multi position front handle (9) into the most suitable mounting point (6) (left side , right side or at the top) to suit the task on hand. V ariable Speed The POL1450 is fitted with a variable speed dial (3) that allows you to adjust the speed to suit the application and material. The tool operates b ...

  • Global Machinery Company POL1450 - page 10

    9. T o tighten, press and hold the spindle lock button (2) and using the pin wrench tighten the outer flange . 10. Turn the new disc by hand, ensuring that it is tight in the flanges and that it rotates fully and does not wobble unduly. 11. Run the angle grinder at no load for at least one minute to ensure the new disc is in good condition. Make su ...

  • Global Machinery Company POL1450 - page 11

    11 Operation in sander mode Fitting the Sandpaper Switch off the tool and disconnect it from the power supply. 1. The GMC grinder/sander/polisher is fitted with a hook & loop base allowing easy changing of accessories . Ensure there are no debris left in the hooks & loops o f the disc before fitting accessories. 2. Align the sandpaper with ...

  • Global Machinery Company POL1450 - page 12

    12 Operation in polisher mode Prepar e the surface For best results, the surf ace should be clean and dry. Most high-gloss surfaces can be cleaned with a mild soap and water solution. For removal of stubborn dirt stains such as road tar , grease, and bug stains , you can use a mild ammonia solution such as that used in glass cleaners. Before using ...

  • Global Machinery Company POL1450 - page 13

    sponge , polishing bonnet and the tool are in good condition. Plug the cordset into the mains socket. 3. Do not overload the tool so that the disc slows down. Let the tool do the work rather than applying pressure . The weight of the tool alone provides sufficient pressure . 4. Hold the tool securely and make sure that you have full control at all ...

  • Global Machinery Company POL1450 - page 14

    14 ...

  • Global Machinery Company POL1450 - page 15

    15 ...

  • Global Machinery Company POL1450 - page 16

    Carefully read the entire Instruction Manual before using this product. Before returning this product for a Warranty Claim or any other reason Please Call 1300 880 001 (Australia) or 0800 445 721 (New Zealand) When you make your call, please have the following information at hand: • GMC Product Type • GMC Product Code A GMC Service Engineer wil ...

Manufacturer Global Machinery Company Category Sander

Documents that we receive from a manufacturer of a Global Machinery Company POL1450 can be divided into several groups. They are, among others:
- Global Machinery Company technical drawings
- POL1450 manuals
- Global Machinery Company product data sheets
- information booklets
- or energy labels Global Machinery Company POL1450
All of them are important, but the most important information from the point of view of use of the device are in the user manual Global Machinery Company POL1450.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Global Machinery Company POL1450, service manual, brief instructions and user manuals Global Machinery Company POL1450. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Global Machinery Company POL1450.

Similar manuals

A complete manual for the device Global Machinery Company POL1450, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Global Machinery Company POL1450 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Global Machinery Company POL1450.

A complete Global Machinery Company manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Global Machinery Company POL1450 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Global Machinery Company POL1450, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Global Machinery Company POL1450, that we can find in the current document
3. Tips how to use the basic functions of the device Global Machinery Company POL1450 - which should help us in our first steps of using Global Machinery Company POL1450
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Global Machinery Company POL1450
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Global Machinery Company POL1450 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Global Machinery Company POL1450?

Use the form below

If you did not solve your problem by using a manual Global Machinery Company POL1450, ask a question using the form below. If a user had a similar problem with Global Machinery Company POL1450 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)