English dropdown-ico

Manual Raypak 185A

18 pages 4.42 mb
Download

Go to site of 18

Summary
  • Raypak 185A - page 1

    RAYPAK REPLACEMENT INSTRUCTIONS IMPORTANT NOTICE These instructions are intended primar ily for use by qua lified personnel s pecif ical ly trained and experi enced in the insta llati on of this type of heating equipment and related system components. Installation and service pers onnel may be required to be licensed in some states. Persons not qua ...

  • Raypak 185A - page 2

    r r Fig. 1 REMOVE THESE SCREWS Fig. 2 Page 2 2151 Eastman Ave., Oxnar d, CA 93030 805-278-5300 Fax 800-777-7026 www.raypak.c om Technical suppor t is availa ble M-F, 5:30 A M to 5 :00 PM PS T, at 800- 947-2975 or 800- 627-2975 REMOVE THESE SCREWS ACCESSING THE BOARD - MODELS 206A, 207A, 266A, 267A, 336A, 337A, 406A, 407A: 1. Turn off the power to t ...

  • Raypak 185A - page 3

    REMOVING THE CIR CUIT BOARD - MODELS 185A/B, 265A/B, 33 5A/B, 405A/B: Make sure the power and gas are off. 1. Unplug all connectors from old circuit board. Fig. 7 . 2. Unplug keypad ribbon from old circuit board. 3. Remove four screws as shown in Fig. 8 . 4. Remove ol d circuit board. Fig. 7 2.2 UNPLUG ALL CONNECTOR S REMOVE KEYBOARD RIBBON Fig. 8 ...

  • Raypak 185A - page 4

    2151 Eastman Ave., Oxnar d, CA 93030 805-278-5300 Fax 800-777-7026 www.raypak.c om Technical suppor t is availa ble M-F, 5:30 A M to 5 :00 PM PS T, at 800- 947-2975 or 800- 627-2975 Page 4 UNPLUG ALL CONNECTORS REMOVE MOUNTING S CREWS Fig. 9 Fig. 10 REMOVING THE CIRCUI T BOARD - MODELS 206A, 207A, 266A, 267A, 336A , 337A, 406A, 407A: Make sure the ...

  • Raypak 185A - page 5

    Page 5 DISCONNECTING IGNITI ON CONTROL - M ODEL S 185A, 265A, 33 5A, AND 405A ONLY : Make sure the power and gas are off. 1. Unplug all wires and connect ors from i gnition control. (See Fig. 11 .) Note: The ignition control is now part of the new control circuit b oard. Old module can be left in place but not used. Fig. 11 UNPLUG ALL WIRES 2151 Ea ...

  • Raypak 185A - page 6

    Page 6 PROPANE HEATERS ONLY: Make sure the power and gas are off. 1. Locate the pr opane tab on the board as shown in Fig. 12 . 2. Break off tab with pliers as shown in Fig. 13 & Fig. 14 . Fig. 12 Fig. 14 PROPANE BROKEN TAB 2151 Eastman Ave., Oxnar d, CA 93030 805-278-5300 Fax 800-777-7026 www.raypak.c om Technical suppor t is availa ble M-F, 5 ...

  • Raypak 185A - page 7

    MODELS 185, 265, 335 & 405, A & B SERIES, LOW NOX ONLY: Make sure the power and gas are off. 1. DO NOT break tab See Fig. 15 and Fig.16. 2. No additional wiring or connecti ons are necessary. 2151 Eastman Ave., Oxnar d, CA 93030 805-278-5300 Fax 800-777-7026 www.raypak.c om Technical suppor t is availa ble M-F, 5:30 A M to 5 :00 PM PS T, at ...

  • Raypak 185A - page 8

    LOW NOX MODELS 207A, 267A, 337A & 407A: Make sure the power and gas are off. 1. Locate Lo Nox tab and P-10 air switch termin al on the board as shown i n Fig. 17 and Fig. 18 . 2. Break off tab shown in Fig. 19 with pliers. 3. Attach the wire from the air s witch to the P-10 locati on shown in Fig. 20 . 2151 Eastman Ave., Oxnar d, CA 93030 805-2 ...

  • Raypak 185A - page 9

    Page 9 NEW CIRCUIT BOARD & GASKET INSTALLATION USING OLD BEZE L - M ODEL S 185, 265, 335 & 405, A & B SERIES: Make sure the power and gas are off. Note: Disregard window gasket installation i f already present. LA Y B OA RD DOWN Fig. 22 CLEAR WINDOW GASKET STICKY SIDE TO PLASTIC BEZEL RE-ASSEMBLE WITH NEW BOAR D MOUNTING SCREWS Fig. 23 ...

  • Raypak 185A - page 10

    GASKET & NEW CIRCUIT BO ARD NEW BEZEL INSTALLATION - MODELS 206A, 207A, 266A, 267A, 336A, 337A, 406A, 407A: Make sure the power and gas are off. Note: Disregard window gasket installation i f already present. 1. Remove backing on gasket and install a dhesive side on the control panel bezel as shown in Fig. 24 & Fig. 25 . 2. Re-assemble with ...

  • Raypak 185A - page 11

    Page 11 REMOVING & REPLACING SENSOR - MODELS 185, 265, 335 & 405, A & B SERIES: Make sure the power and gas are off. 1. Loosen drain plug to relieve pressure i n heat exchanger. See Fig. 27 . 2. Remove five screws and in/out access panel as shown in Fig. 28 . 3. Re-route the 2-wire s ensor connector from the board (P1) back towa rds the ...

  • Raypak 185A - page 12

    Page 12 Fig. 33 Fig. 32 CLEAR PLASTIC STRIP WITH THIN CONNECTOR Fig. 34 PLASTIC SHIELD & BRACKET INSTAL LATION - MODELS 185, 265, 335 & 405, A & B SERIES: Make sure the power and gas are off. 1. Note that the plastic shie ld is installed under the front bracket as pictured. Install the shield brackets and plastic shield using the existi ...

  • Raypak 185A - page 13

    Ensure the power and the gas has been shut off. 1. Re-connect pilot wire (side B) to new board. See Fig. 35. CONNECT THIS END TO NEW PC BOARD SPARK LUG CONNECT THIS END TO EXISTING PILOT WIRE Fig. 37 EXISTING PILOT WIRE Page 13 P/N 241169 Rev.-3 2151 Eastman Ave., Oxnar d, CA 93030 805-278-5300 Fax 800-777-7026 www.raypak.c om Technical suppor t is ...

  • Raypak 185A - page 14

    Page 14 2151 Eastman Ave., Oxnar d, CA 93030 805-278-5300 Fax 800-777-7026 www.raypak.c om Technical suppor t is availa ble M-F, 5:30 A M to 5 :00 PM PS T, at 800- 947-2975 or 800- 627-2975 P/N 241169 Rev.-3 ...

  • Raypak 185A - page 15

    Page 15 2151 Eastman Ave., Oxnar d, CA 93030 805-278-5300 Fax 800-777-7026 www.raypak.c om Technical suppor t is availa ble M-F, 5:30 A M to 5 :00 PM PS T, at 800- 947-2975 or 800- 627-2975 P/N 241169 Rev.-3 ...

  • Raypak 185A - page 16

    Page 16 2151 Eastman Ave., Oxnar d, CA 93030 805-278-5300 Fax 800-777-7026 www.raypak.c om Technical suppor t is availa ble M-F, 5:30 A M to 5 :00 PM PS T, at 800- 947-2975 or 800- 627-2975 P/N 241169 Rev.-3 ...

  • Raypak 185A - page 17

    Page 17 2151 Eastman Ave., Oxnar d, CA 93030 805-278-5300 Fax 800-777-7026 www.raypak.c om Technical suppor t is availa ble M-F, 5:30 A M to 5 :00 PM PS T, at 800- 947-2975 or 800- 627-2975 P/N 241169 Rev.-3 ...

  • Raypak 185A - page 18

    Page 18 2151 Eastman Ave., Oxnar d, CA 93030 805-278-5300 Fax 800-777-7026 www.raypak.c om Technical suppor t is availa ble M-F, 5:30 A M to 5 :00 PM PS T, at 800- 947-2975 or 800- 627-2975 P/N 241169 Rev.-3 ...

Manufacturer Raypak Category Swimming Pool Heater

Documents that we receive from a manufacturer of a Raypak 185A can be divided into several groups. They are, among others:
- Raypak technical drawings
- 185A manuals
- Raypak product data sheets
- information booklets
- or energy labels Raypak 185A
All of them are important, but the most important information from the point of view of use of the device are in the user manual Raypak 185A.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Raypak 185A, service manual, brief instructions and user manuals Raypak 185A. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Raypak 185A.

Similar manuals

A complete manual for the device Raypak 185A, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Raypak 185A by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Raypak 185A.

A complete Raypak manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Raypak 185A - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Raypak 185A, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Raypak 185A, that we can find in the current document
3. Tips how to use the basic functions of the device Raypak 185A - which should help us in our first steps of using Raypak 185A
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Raypak 185A
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Raypak 185A in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Raypak 185A?

Use the form below

If you did not solve your problem by using a manual Raypak 185A, ask a question using the form below. If a user had a similar problem with Raypak 185A it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)