English dropdown-ico

Manual Linksys BEPSR31

66 pages 1.15 mb
Download

Go to site of 66

Summary
  • Linksys BEPSR31 - page 1

    Instant Broadband™ Series Cable/DSL Routers Use this guide to install the following products: BEFSR41 ver . 2 EtherFast ® Cable/DSL Router with 4-Port Switch BEFSRU31 EtherFast ® Cable/DSL Router with USB Port and 3-Port Switch BEFSR11 ver . 2 EtherFast ® 1-Port Cable/DSL Router User Guide ...

  • Linksys BEPSR31 - page 2

    COPYRIGHT & TRADEMARKS Copyright © 2002 Linksys, All Rights Reserved. Linksys and EtherFast are r egistered trademarks of Linksys. Instant Broadband is a trademark of Linksys. Micr osoft, Windows, and the Windows logo are r egistered trademarks of Micr osoft Corporation. All other trademarks and brand names are the pr operty of their respectiv ...

  • Linksys BEPSR31 - page 3

    EtherFast ® Cable/DSL Routers Chapter 7: Configure the PCs 35 Overview 35 Conf iguring W indo ws 95, 98, and Millennium PCs 36 Conf iguring W indo ws 2000 PCs 38 Conf iguring W indo ws XP PCs 40 Chapter 8: Configure the Router 42 Chapter 9: The Cable/DSL Router’ s Web-based Utility 47 Overview 47 Quick and Easy Router Administration 47 Setup 48 ...

  • Linksys BEPSR31 - page 4

    Instant Broadband ™ Series EtherFast ® Cable/DSL Routers Chapter 1: Introduction The Linksys EtherFast ® Cable/DSL Router Congratulations on the purchase of the EtherF ast Cable/DSL Router from Linksys! The Router is the perfect solution for connecting a netw ork of PCs to a high-speed broadband Internet connection and to an Ether net netw ork ...

  • Linksys BEPSR31 - page 5

    EtherFast ® Cable/DSL Routers 3 Instant Broadband ™ Series 2 Package Contents for the 1-Port Router (BEFSR11) • One EtherF ast 1-Port Cable/DSL Router • One Setup Wizard CD-R OM with User Guide Included • One P ow er Adapter • One F ast Star t Guide • One Registration Card (not sho wn) • One Windo ws PC equipped with: • TCP/IP Prot ...

  • Linksys BEPSR31 - page 6

    EtherFast ® Cable/DSL Routers The Router’ s f irew all (N A T) protects your netw ork of PCs so users on the pub- lic, Internet side cannot “see” your PCs. This is ho w your LAN, or netw ork, remains priv ate. The Router protects your netw ork by inspecting the f irst pack- et coming in through the W AN por t before deliv er y to the f inal ...

  • Linksys BEPSR31 - page 7

    This user guide co vers the basic steps for setting up a netw ork with a router . After going through the appropriate “Getting to Kno w the Router” chapter (Chapter 2, 3, or 4, depending on which Router y ou hav e), most users will onl y need to use the follo wing chapters: • Chapter 5: Connect the Router This chapter instructs you on ho w to ...

  • Linksys BEPSR31 - page 8

    EtherFast ® Cable/DSL Routers 9 Instant Broadband ™ Series 8 Pow e r Green . The Powe r LED lights up when the Router is po w ered on. Link/Act Gr een . The Link/Act LED ser v es two purposes. If the LED is continuously lit, the Router is successfull y connected to a device through the corresponding port ( 1 , 2 , 3 or 4 ). If the LED is flicker ...

  • Linksys BEPSR31 - page 9

    EtherFast ® Cable/DSL Routers 11 Instant Broadband ™ Series 10 Chapter 3: Getting to Know the 1- Port EtherFast Cable/DSL Router The rear panel of the Router is where all of the Router’ s cab ling connections are made, and where y ou can reset or conf igure the Router’ s LAN por t, as sho wn in Figure 3-1. WA N The WA N (W ide Area Netw ork) ...

  • Linksys BEPSR31 - page 10

    EtherFast ® Cable/DSL Routers Full/Col Gr een . The Full/Col LED also ser ves tw o pur poses. If this LED remains lit, a LAN port connection is being successful- ly maintained. If the LED flickers, the connection is experi- encing collisions. Infrequent collisions are normal. If this LED flickers too often, there ma y be a problem with your connec ...

  • Linksys BEPSR31 - page 11

    EtherFast ® Cable/DSL Routers 15 Instant Broadband ™ Series 14 This USB icon, sho wn in Figure 4-2, denotes the presence of a USB port or connector . The 3-P or t Router comes with a USB cable that has tw o different types of con- nectors. T ype A, the master connector, is shaped lik e a rectangle and plugs into your PC’ s USB port. T ype B , ...

  • Linksys BEPSR31 - page 12

    EtherFast ® Cable/DSL Routers The W AN Indicators Link Gr een . The Link LED lights up when a successful connec- tion is made betw een the Router and your broadband device or netw ork. Act Gr een . The Act LED flickers when the Router is sending or receiving data o ver the broadband WA N port. Diag Red . The Diag LED lights up when the Router goes ...

  • Linksys BEPSR31 - page 13

    EtherFast ® Cable/DSL Routers 19 Instant Broadband ™ Series 18 1. Before you be gin, make sure that all of y our hardw are is po w ered off, includ- ing the Router , PCs, hubs, switches, and cable or DSL modem. 2. If you ha ve the 4-P ort Router, go to step 2.A. If y ou hav e the 1-Port Router , go to step 2.B . If you ha ve the 3-P or t Router, ...

  • Linksys BEPSR31 - page 14

    EtherFast ® Cable/DSL Routers 21 Instant Broadband ™ Series 20 If the Router’ s LAN ports are all full and you still ha ve PCs and/or devices to connect, connect a hub or a switch to the Router using an Ethernet cable. T o do so, use the Router’ s Uplink port to connect to a standard por t on a hub or switch. This lea ves y ou with new , ope ...

  • Linksys BEPSR31 - page 15

    EtherFast ® Cable/DSL Routers 23 Instant Broadband ™ Series 22 3. Select Sear ch f or the best driv er for y our device (Recommended) , sho wn in Figure 6-2. Click the Ne xt button. 4. Insert the driver disk into the flopp y driv e, and select Floppy disk dri ves only , as sho wn in Figure 6-3. Click the Ne xt button to start the search for your ...

  • Linksys BEPSR31 - page 16

    EtherFast ® Cable/DSL Routers 7. W indows will notify y ou that it has completed copying the dri ver f iles to your PC, as sho wn in Figure 6-6. Click the Finish button to complete the USB driv er installation. 8. W indows will ask y ou if you w ant to restar t your PC, as sho wn in Figure 6- 7. Click the Y es button so your ne w installation will ...

  • Linksys BEPSR31 - page 17

    EtherFast ® Cable/DSL Routers 27 Instant Broadband ™ Series 9. When y our PC has f inished restarting, click the Start button, and select Settings and Control P anel . Double-click Netw ork . Make sure that TCP/IP is installed on your PC, as sho wn on the screen in Figure 6-8. By default, W indows 98 has TCP/IP installed. If TCP/IP is not instal ...

  • Linksys BEPSR31 - page 18

    EtherFast ® Cable/DSL Routers 5. When the Digital Signature Not F ound screen appears, as sho wn in F igure 6- 13, W indo ws will ask you if y ou want to continue the installation. Click the Ye s button. 6. Click the Ne xt button from the screen sho wn in Figure 6-14 to allo w W indows to cop y the dri ver f iles to your PC. 29 Instant Broadband ? ...

  • Linksys BEPSR31 - page 19

    EtherFast ® Cable/DSL Routers 31 Instant Broadband ™ Series 30 1. W ith the Router pow ered up and connected to your PC’ s USB port using a USB cable, start up your PC in W indows Millennium. 2. W indows will notify y ou that new hardw are has been detected (see Figure 6-17). Insert the driver disk. Select A utomatic search f or a better driv ...

  • Linksys BEPSR31 - page 20

    EtherFast ® Cable/DSL Routers 33 Instant Broadband ™ Series 32 1. W ith the Router connected to your PC’ s USB por t using a USB cable, start up your PC in W indows XP . 2. W indows will notify y ou that new hardw are has been detected (shown in Figure 6-22). Select Install fr om a list or specif ic location (Adv anced) , and click the Next bu ...

  • Linksys BEPSR31 - page 21

    EtherFast ® Cable/DSL Routers Chapter 7: Configure the PCs The instructions in this chapter will help you conf igure each of your comput- ers to be able to communicate with the Router . T o do this, you need to conf igure your PC’ s netw ork settings to obtain an IP (or TCP/IP) address automatically (called DHCP). Computers use IP addresses to c ...

  • Linksys BEPSR31 - page 22

    EtherFast ® Cable/DSL Routers 3. Click the IP Addr ess tab and select Obtain an IP address automaticall y , as sho wn in Figure 7-2. 4. No w click the Gate wa y tab to ensure that the Installed Gatew a y f ield is left blank. Click the OK button. 5. Click the OK button again. Windo ws may ask y ou for the original W indows installation disk or add ...

  • Linksys BEPSR31 - page 23

    EtherFast ® Cable/DSL Routers 4. Select Internet Pr otocol (TCP/IP) , as sho wn in Figure 7-4, and click the Pr oper ties button. 5. Select Obtain an IP ad dr ess automatically , as sho wn in Figure 7-5. Once the new windo w appears, click the OK button. Click the OK button again to complete the PC conf iguration. 6. Restart your computer . Go to ...

  • Linksys BEPSR31 - page 24

    EtherFast ® Cable/DSL Routers 4. Select Internet Pr otocol (TCP/IP) , as sho wn in Figure 7-7, and click the Pr oper ties button. 5. Select Obtain an IP addr ess automaticall y , as shown in F igure 7-8. Once the new windo w appears, click the OK button. Click the OK button again (or the Close button if any settings w ere changed) to complete the ...

  • Linksys BEPSR31 - page 25

    EtherFast ® Cable/DSL Routers 43 Instant Broadband ™ Series 42 3. The Router conf iguration screen will appear with the Setup tab selected. Based on the setup instructions from your ISP , you ma y need to provide the follo wing infor mation. Host Name and Domain Name : These f ields allo w you to pro vide a host name and domain name for the Rout ...

  • Linksys BEPSR31 - page 26

    EtherFast ® Cable/DSL Routers 45 Instant Broadband ™ Series DHCP or Obtain an IP Addr ess A utomatically If your ISP sa ys that you are connecting through DHCP or a dynamic IP address from your ISP , perform these steps: A . Select Obtain an IP automatically as the W AN Connection T ype, as sho wn in Figure 8-4. B . Click the Appl y button to sa ...

  • Linksys BEPSR31 - page 27

    EtherFast ® Cable/DSL Routers Chapter 9: The Cable/DSL Router’ s W eb-based Utility F or your con venience, use the Router’ s w eb-based utility to administer it. This chapter will explain all of the functions in this utility . The utility can be accessed via Microsoft Internet Explorer or Netscape Navigator through use of a computer connected ...

  • Linksys BEPSR31 - page 28

    EtherFast ® Cable/DSL Routers • Device IP Addr ess and Subnet Mask The v alues for the Router’ s IP Address and Subnet Mask are sho wn here. The def ault values are 192.168.1.1 for the Device IP Address and 255.255.255.0 for the Subnet Mask. • W AN Connection T ype The Router supports f ive connection types: DHCP , PPP oE, Static IP , PPTP , ...

  • Linksys BEPSR31 - page 29

    EtherFast ® Cable/DSL Routers 51 Instant Broadband ™ Series PPP oE Some DSL-based ISPs use PPP oE (P oint-to-P oint Protocol o ver Ethernet) to estab- lish Internet con- nections for end- users. If you are connected to the Internet through a DSL line, check with your ISP to see if they use PPP oE. If they do, you will ha ve to enable it, as sho ...

  • Linksys BEPSR31 - page 30

    EtherFast ® Cable/DSL Routers 53 Instant Broadband ™ Series 52 RAS Remote Access Service (RAS) (sho wn in Figure 9-8) is a service that applies to con- nections in Singapore only . F or users in Singapore, check with Singtel for information on RAS. User Name and P assword Enter the User Name and Pass word supplied b y Singtel. RAS Plan Select th ...

  • Linksys BEPSR31 - page 31

    EtherFast ® Cable/DSL Routers 55 Instant Broadband ™ Series 54 The Status tab, sho wn in F igure 9-10, displa ys the Router’ s status; it reflects the data and selections you’ ve entered using the Setup screen. All of the information provided on this screen is read-onl y . T o make changes, select the Setup tab . • Host Name This f ield sh ...

  • Linksys BEPSR31 - page 32

    EtherFast ® Cable/DSL Routers 57 Instant Broadband ™ Series 56 • DHCP Server DHCP is already enab led by factor y default. If you already ha ve a DHCP server on your netw ork, set the Router’ s DHCP option to Disab le . Click the A pply button. If y ou disable DHCP , remember to assign a static IP address to the Router . • Starting IP Addr ...

  • Linksys BEPSR31 - page 33

    EtherFast ® Cable/DSL Routers 59 Instant Broadband ™ Series The Log tab, sho wn in Figure 9-12, pro vides you with a lo g of all incoming and outgoing URLs or IP addresses for your Internet connection. T o access activity lo gs, select the Enab le option next to Access Log. This func- tion can be disabled b y clicking the Disable radio button. W ...

  • Linksys BEPSR31 - page 34

    EtherFast ® Cable/DSL Routers Under the Help tab, sho wn in F igure 9-14, y ou’ ll f ind links to all of the Utility’ s internal suppor t documentation, including the application that upg rades the Router’ s f irmware. New f ir mware versions are posted at www .linksys.com and can be do wnloaded for free. If the Router can access the Interne ...

  • Linksys BEPSR31 - page 35

    EtherFast ® Cable/DSL Routers 63 Instant Broadband ™ Series T o upgrade the Router’ s f ir mware: 1. Select the Help tab (see Figure 9-14). 2. Click Upgrade Firmwar e to displa y a new windo w (see Figure 9-15). 3. Click the Br o wse button to f ind the f irmware upgrade f ile that you do wn- loaded from the Linksys w ebsite and then extracted ...

  • Linksys BEPSR31 - page 36

    EtherFast ® Cable/DSL Routers 65 Instant Broadband ™ Series 64 Using MTU (Maximum T ransmission Unit) • This feature specif ies the largest pack et size permitted for network transmis- sion. Select Enab le and enter the value desired. It is recommended that you lea ve this value in the 1200 to 1500 range. F or most DSL users, it is recom- mend ...

  • Linksys BEPSR31 - page 37

    EtherFast ® Cable/DSL Routers 67 Instant Broadband ™ Series 66 • T elnet A ter minal emulation protocol commonly used on Internet and TCP/IP-based net- w orks. It allows a user at a terminal or computer to log onto a remote device and run a program. • SMTP (Simple Mail T ransfer Protocol) The stan- dard e-mail protocol on the Internet. It is ...

  • Linksys BEPSR31 - page 38

    EtherFast ® Cable/DSL Routers 69 Instant Broadband ™ Series 68 5. Enter the IP address of the ser ver that y ou w ant the Internet users to be able to access. T o f ind the IP address, go to “ Appendix F: Finding the MA C Address and IP Address for Y our Ethernet Adapter . ” 6. Check the Enab le box to enable the services you ha ve def ined. ...

  • Linksys BEPSR31 - page 39

    EtherFast ® Cable/DSL Routers 71 Instant Broadband ™ Series 70 If the Router is connected to more than one netw ork, it may be necessary to set up a static route betw een them. A static route is a pre-deter mined pathwa y that netw ork infor mation must trav el to reach a specif ic host or netw ork. From the Static Routing tab, as sho wn in F ig ...

  • Linksys BEPSR31 - page 40

    EtherFast ® Cable/DSL Routers 73 Instant Broadband ™ Series 72 The DMZ Hosting feature, sho wn in Figure 9-22, allo ws one local user to be exposed to the Internet for use of a special-pur pose ser vice such as Internet gaming and videoconferencing. Whereas P or t Range F orwarding can onl y forward a maximum of 10 ranges of ports, DMZ hosting f ...

  • Linksys BEPSR31 - page 41

    EtherFast ® Cable/DSL Routers 75 Instant Broadband ™ Series 74 Appendix A: Troubleshooting This appendix consists of tw o par ts: “Common Problems and Solutions” and “Frequentl y Asked Questions. ” Pro vided are possible solutions to problems regarding the installation and operation of the Router . If your situation is described here, th ...

  • Linksys BEPSR31 - page 42

    EtherFast ® Cable/DSL Routers F or Windo ws XP: The follo wing instr uctions assume you are running W indows XP with the default interface. If you are using the Classic interface (where the icons and menus look like pre vious W indo ws versions), please follo w the instructions for W indows 2000. A. Click Star t and Contr ol P anel . B . Click the ...

  • Linksys BEPSR31 - page 43

    EtherFast ® Cable/DSL Routers 79 Instant Broadband ™ Series 78 C. In the command prompt, type ping 192.168.1.1 and press the Enter key . • If you get a repl y , the computer is communicating with the Router . • If you do NO T get a reply , please check the cable, and make sure Obtain an IP addr ess automatically is selected in the TCP/IP set ...

  • Linksys BEPSR31 - page 44

    EtherFast ® Cable/DSL Routers Y our VPN ma y require por t 500/UDP packets to be passed to the computer that is connecting to the IPSec server . Refer to “Problem #7, I need to set up online game hosting or use other Internet applications” for details. Check the Linksys w ebsite for more infor mation at www .linksys.com . 6. I need to set up a ...

  • Linksys BEPSR31 - page 45

    EtherFast ® Cable/DSL Routers 8. I can’t get the Internet game , server , or application to work. If you are ha ving diff iculties getting an y Inter net game, server , or application to function properl y , consider exposing one PC to the Internet using DeMilitarized Zone (DMZ) hosting. This option is a v ailable w hen an applica- tion requires ...

  • Linksys BEPSR31 - page 46

    EtherFast ® Cable/DSL Routers 13. The fir mware upgrade failed, and/or the Diag LED is flashing. The upgrade could hav e f ailed for a number of reasons. F ollo w these steps to upgrade the f ir mware and/or make the Diag LED stop flashing: A. If the f irmware upgrade f ailed , use the TFTP pro gram (it was do wnloaded along with the f irmware). O ...

  • Linksys BEPSR31 - page 47

    EtherFast ® Cable/DSL Routers 17. The Diag LED stays lit continuously . • The Diag LED lights up when the de vice is f irst pow ered up. Meantime, the system will boot up itself and check for proper operation. After f in- ishing the checking procedure, the LED turns off to sho w that the system is w orking f ine. If the LED remains lit after thi ...

  • Linksys BEPSR31 - page 48

    EtherFast ® Cable/DSL Routers 89 Instant Broadband ™ Series 88 Does the Router support ICQ send file? Y es, with the follo wing f ix: click ICQ menu -> pr efer ence -> connections tab-> , and check I am behind a f ir e- wall or pr o xy . Then set the f irew all time-out to 80 seconds in the f irew all set- ting. The Internet user can th ...

  • Linksys BEPSR31 - page 49

    EtherFast ® Cable/DSL Routers 91 Instant Broadband ™ Series 90 Does the Router pass PPTP packets or actively route PPTP sessions? The Router allo ws PPTP packets to pass through. Is the Router cross-platform compatible? Any platform that supports Ether net and TCP/IP is compatible with the Router . How many ports can be simultaneously forwarded? ...

  • Linksys BEPSR31 - page 50

    EtherFast ® Cable/DSL Routers Bridge - A device that interconnects dif ferent netw orks together . Br oadband - A data-transmission scheme in which multiple signals share the bandwidth of a medium. This allo ws the transmission of voice, data, and video signals o ver a single medium. Cab le television uses broadband techniques to deliv er dozens o ...

  • Linksys BEPSR31 - page 51

    EtherFast ® Cable/DSL Routers DHCP supports static addresses for computers containing W eb servers that need a permanent IP address. DMZ - ( D e M ilitarized Z one) allo ws one IP address (or computer) to be exposed to the Internet. Some applications require multiple TCP/IP ports to be open. It is recommended that you set y our computer with a sta ...

  • Linksys BEPSR31 - page 52

    EtherFast ® Cable/DSL Routers Full Duplex - The ability of a device or line to transmit data simultaneousl y in both directions. Gatew a y – A device that interconnects netw orks with different, incompatib le communications protocols. Half Duplex - Data transmission that can occur in two directions o ver a single line, but only one direction at ...

  • Linksys BEPSR31 - page 53

    EtherFast ® Cable/DSL Routers NetBEUI ( NetB IOS E xtended U ser I nterface) - The transpor t la yer for NetBIOS. NetBIOS and NetBEUI w ere originally part of a single protocol suite that was later separated. NetBIOS sessions can be transported o ver NetBEUI, TCP/IP , and SPX/IPX protocols. NetBIOS - The nativ e networking protocol in DOS and W in ...

  • Linksys BEPSR31 - page 54

    EtherFast ® Cable/DSL Routers nostic tool or debugging feature, especially w hen fending off an attack. It enables the administrator to k eep close track of switch performance and alter it if necessary . P ort mir roring can be managed locally or remotel y . PPP oE ( P oint to P oint P rotocol o ver E thernet) - A method used mostl y b y DSL pro v ...

  • Linksys BEPSR31 - page 55

    EtherFast ® Cable/DSL Routers TCP/IP - T ransmission Control Protocol/Internet Protocol (TCP/IP) is the basic communication language or protocol of the Internet. It can also be used as a communications protocol in a pri v ate netw ork (either an intranet or an extranet). When you are set up with direct access to the Internet, your computer is pro ...

  • Linksys BEPSR31 - page 56

    EtherFast ® Cable/DSL Routers 105 Instant Broadband ™ Series URL ( U niform R esource L ocator) - The address that def ines the route to a f ile on the W eb or any other Internet facility . URLs are typed into the bro wser to access W eb pages, and URLs are embedded within the pages themselves to pro- vide the h yper text links to other pages. U ...

  • Linksys BEPSR31 - page 57

    EtherFast ® Cable/DSL Routers 107 Instant Broadband ™ Series 106 Step T wo: Pinging for a Web Address While the IP address returned abov e would w ork as your e-mail server address, it ma y not be permanent. IP addresses change all the time. W eb addresses, ho w- ev er , usually don’ t. Because of this, you’ re likely to ha ve fe wer prob le ...

  • Linksys BEPSR31 - page 58

    EtherFast ® Cable/DSL Routers 6. Find and double-click TCP/IP in the list to the right (see F igure D-2). 7. After a fe w seconds, the main Network windo w will appear . The TCP/IP Protocol should no w be listed , as sho wn in Figure D-3. 8. Click the OK button. W indows ma y ask for original W indo ws installation f iles. Supply them as needed , ...

  • Linksys BEPSR31 - page 59

    EtherFast ® Cable/DSL Routers 111 Instant Broadband ™ Series Appendix E: T wisted-Pair Cabling There are dif ferent grades, or “categories, ” of twisted-pair cabling. Category 5 is the most reliable and most highl y recommended. Category 3 is a good sec- ond choice. Straight-through cables are used for connecting computers to a hub . Crosso ...

  • Linksys BEPSR31 - page 60

    EtherFast ® Cable/DSL Routers 3. Write down the Adapter Address as sho wn on your computer screen (see Figure F-3). This is the MA C address for y our Ethernet adapter and will be sho wn as a series of numbers and letters. The MA C address/Adapter Address is what you will use for MA C Address Cloning or MA C Filtering. The example in F igure F-3 s ...

  • Linksys BEPSR31 - page 61

    EtherFast ® Cable/DSL Routers When entering the information using the Router’ s web-based utility , you will type the 12-digit MA C addr ess in this format, XXXXXXXXXXXX without the hyphens for MA C Filtering. See Figure F-6. When entering information for MAC Address Cloning, type the 12-digit MA C addr ess (see Figure F-7). 115 Instant Broadban ...

  • Linksys BEPSR31 - page 62

    EtherFast ® Cable/DSL Routers 3. From the Setup screen that appears, sho wn in Figure G-3, select Obtain an IP automat- ically from the W AN Connection T ype drop- do wn menu. Then, click the Security tab . 4. Select Enab le for A OL Parental Controls from the Security tab, sho wn in Figure G-4, and click the OK button on the screen that appears. ...

  • Linksys BEPSR31 - page 63

    EtherFast ® Cable/DSL Routers 119 Appendix H: 4-Port Router Specifications Model Number BEFSR41 ver . 2 Standards IEEE 802.3 (10BaseT), IEEE 802.3u (100BaseTX) Protocol CSMA/CD Ports LAN: Four 10/100 RJ-45 switched ports (and shared uplink) W AN: One 10Base-T Ether net RJ-45 port for the cable or DSL modem Speed LAN: 10/100Mbps W AN: 10Mbps Cablin ...

  • Linksys BEPSR31 - page 64

    EtherFast ® Cable/DSL Routers 121 Instant Broadband ™ Series 120 Appendix J: 3-Port Router Specifications Model Number BEFSRU31 Standards IEEE 802.3 (10BaseT), IEEE 802.3u (100BaseTX), USB Specification 1.0 & 1.1 Protocol CSMA/CD Ports LAN: Three 10/100 RJ-45 Switched ports (and shared uplink), One USB port W AN: One 10Base-T Ether net RJ-45 ...

  • Linksys BEPSR31 - page 65

    EtherFast ® Cable/DSL Routers Appendix L: Contact Information F or help with the installation or operation of your Instant Broadband EtherF ast Cable/DSL Router, contact Linksys T echnical Suppor t at one of the phone numbers or Internet addresses below . Sales Information 800-546-5797 (1-800-LINKSYS) T echnical Suppor t 800-326-7114 RMA Issues 94 ...

  • Linksys BEPSR31 - page 66

    © Copyright 2002 Linksys, All Rights Reserved. www .linksys.com ...

Manufacturer Linksys Category Network Router

Documents that we receive from a manufacturer of a Linksys BEPSR31 can be divided into several groups. They are, among others:
- Linksys technical drawings
- BEPSR31 manuals
- Linksys product data sheets
- information booklets
- or energy labels Linksys BEPSR31
All of them are important, but the most important information from the point of view of use of the device are in the user manual Linksys BEPSR31.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Linksys BEPSR31, service manual, brief instructions and user manuals Linksys BEPSR31. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Linksys BEPSR31.

Similar manuals

A complete manual for the device Linksys BEPSR31, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Linksys BEPSR31 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Linksys BEPSR31.

A complete Linksys manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Linksys BEPSR31 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Linksys BEPSR31, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Linksys BEPSR31, that we can find in the current document
3. Tips how to use the basic functions of the device Linksys BEPSR31 - which should help us in our first steps of using Linksys BEPSR31
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Linksys BEPSR31
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Linksys BEPSR31 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Linksys BEPSR31?

Use the form below

If you did not solve your problem by using a manual Linksys BEPSR31, ask a question using the form below. If a user had a similar problem with Linksys BEPSR31 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)