English dropdown-ico

Manual Havis-Shields KK-100-06

22 pages 2.3 mb
Download

Go to site of 22

Summary
  • Havis-Shields KK-100-06 - page 1

    INSTALL INSTRUCTIONS KK-100-06 & KK-120-06 KWIK-KIT PRISONER TRANSPORT INSERT FORD and CHEVY VAN PR ISONER TRANSPORT TOOLS REQUIRED: ¼” & 3/8” Ratcheting Wrenches ¼” & 3/8”Air Ratchets (recommended) 3/8” Impact Guns (recommended) ¼” & 3/8” Standard Socket Sets Powered Drill Powered Screwdriver (recommended) Drill Bi ...

  • Havis-Shields KK-100-06 - page 2

    KK-XXX-06_INST_8-07 2 40” COMPARTMENT (cont): QTY DESCRIPTION PART # USED FOR: 40 #10 x 1” Phillips pan head sheet metal screw GSM33196 Floor, wall to ceiling 25 #8 x 3/8” Phillips flat head screw GSM33179 Vent plates/dome lights 5 ½” Flat washer GSM31009 Grab straps/seat belts 5 ½” Lock washer GSM31030 Grab straps/seat belts 5 ½” x ...

  • Havis-Shields KK-100-06 - page 3

    KK-XXX-06_INST_8-07 3 Rear OEM Trim modifications 1997-2 007 Chevrolet G-Series Van Installation of Kwik Kit is very similar in Ford and Chevy Vans. All kits start with a measurement at th e rear floor. The rear plastic floor trim on Chevy vans must be cut straight across as shown in phot o. Measure seven inches ( 7” ) from rear center of trim an ...

  • Havis-Shields KK-100-06 - page 4

    KK-XXX-06_INST_8-07 4 Ford Driver-Side rear Ford Passenger-Side rear 8”inches 8” inches Note: Photos above show a Chevrolet Van. Photos ar e intended to show rubber floor mat option only. ***Kwik kits are designed for cargo vans with no rear OEM trim, however they can be installed into passenger window vans. Some rear trim remo val or modificat ...

  • Havis-Shields KK-100-06 - page 5

    KK-XXX-06_INST_8-07 5 1. Remove clear shrink- wrap covering the prisoner transport assembly. 2. This is the rear 40/60/or 80 section of the kit. 3. Remove all black hardware, wood panels and brackets holding wood panels. 4. Remove bolts holding the kit to the wood pallet. 5. With all hardware removed the remaining sections should match the sub-asse ...

  • Havis-Shields KK-100-06 - page 6

    KK-XXX-06_INST_8-07 6 Remove all black hardw are from asse mbled unit. This will give you the subassemblies as they are shown on the follow ing pages. ...

  • Havis-Shields KK-100-06 - page 7

    KK-XXX-06_INST_8-07 7 The following photos are the main subassemb lies as they are shipped from the factory. Remove drawing on final page and referen ce the item #’s as you install this kit. Driver Side Bench/Wall/ Front bulkhead wing section Driver-side ceiling Item #7 Center Divider Item #5 Passenger Side Rear Bench/Wall/ 3 rd Compartment Bulkh ...

  • Havis-Shields KK-100-06 - page 8

    KK-XXX-06_INST_8-07 8 KWIK KIT LAYOUT Diamond plate floor and ceiling sections are not shown for detail purposes. 3 rd Compartment ceiling Item #12 Rear bulkhead/door assembly Item #6 3 r d Compartment Bulkhead/door assembly Item #11 ...

  • Havis-Shields KK-100-06 - page 9

    KK-XXX-06_INST_8-07 9 VERY IMPORTANT: Be sure that all Auxiliary lighting, video systems, Kwik kit options, and wiring are complete. Access is s ever ely limited after kit is installed. If optional rear load light(s) (KK-RLL) was ordered, install at this time. See KK-RLL install instructions Run all wiring for dome lights, power vents, video system ...

  • Havis-Shields KK-100-06 - page 10

    KK-XXX-06_INST_8-07 10 Place Driver-side Bench/Wall assembly into van so bench rests on wheel well Item #1 Remove steel support bracket for Emergency Exit Hatch pin. Re-install when attaching Front Bulkhead to Bench/Wall assemblies Item #3 Item #2 Place Passenger-side Bench/Wall assembly into van so bench rests on wheel well Remove Emergency Exit H ...

  • Havis-Shields KK-100-06 - page 11

    KK-XXX-06_INST_8-07 11 Current view of installa tion Place Center Divider into vehicle. Item #5 Item #4 Item #3 Approximate center Item #5 Carefully place Driver-side Ceiling section into vehicle. Item #7 Loosely bolt Center Divider to Front Bulkhead Item #5 to #3 Place (2) Diamond Plate Floors between Bench/Wall assemblies and Front bulkhead . Pla ...

  • Havis-Shields KK-100-06 - page 12

    KK-XXX-06_INST_8-07 12 Remove screws holding the center divider together where 3 rd Compartment Bulkhead will be mounted. Item #5 Position 3 rd Compartment Ceiling into vehicle. Item #12 Current view of installa tion Slide the ceiling sections out of the way in order to access A/C hoses, wires, etc. Note: These components will be ha rd to access on ...

  • Havis-Shields KK-100-06 - page 13

    Place 3 rd compartment bench Photo shows optional storage door Note: Be careful not to scratch bulkheads. Item #10 Item #10 to #9 Bolt 3 rd Compartment Bench to 3 rd Compartment Divider using ¼” x ¾” carriage bolts and serrated nuts. Nuts should be on the inside of the bench Items #9, #8, & #12 all bolt together VERY IMPORTANT!!! Item #9 ...

  • Havis-Shields KK-100-06 - page 14

    KK-XXX-06_INST_8-07 14 Item #6 to #5 Item #6 Item #6 Place Rear Bulkhead Doorframe into vehicle Position between Driver and Passenger-side Bench/Wall assemblies Loosely attach Doorframe to Center divider using #10 x 3/8” flat head machine screws and nylock nuts Item #6 to #2 Place the 3 rd Compartment Doorframe assembly . Item #11 Note: It is rec ...

  • Havis-Shields KK-100-06 - page 15

    KK-XXX-06_INST_8-07 15 An awe or scribe will help align the holes THE FOLLOWING STEPS AR E EXTREMLY CRITI CAL FOR A SUCCESFULL INSTALLATION! PLEASE FOLLOW THESE INSTRUCTIONS CAREFULLY. Item #1 Rear driver-side doorframe wing Position of driver-side Rear Doorframe when insta ling with factory rear air There should be at least ¼” of space between ...

  • Havis-Shields KK-100-06 - page 16

    KK-XXX-06_INST_8-07 16 Top Passenger-Side rear Top Driver-Side rear Item #6 Approximately 3”inches Item #6 3” inches Item #7 to #1 Item #6 Item #6 Position Driver-side Ceiling section to mate with Bench/Wall assem bly. Pre- drill 5/32” holes into Ceiling, using Bench/Wall assembly holes as a guide. With unit positioned acc ording to m easurem ...

  • Havis-Shields KK-100-06 - page 17

    Begin to tighten ALL loose hardware on the remainder of the unit, being sure to align edges and bends of materials being tightened. This will square the unit to itself. Pre-drill through Ceiling sections, (using Divider as a template), with 3/16” d rill bit and attach using ¼” x 1 ½” hex head lag bolts Item #5 through #8 into #7 Attach rema ...

  • Havis-Shields KK-100-06 - page 18

    KK-XXX-06_INST_8-07 18 3/8” x 2” Hex head bolt, washers, and nut On the Rear doorframe , remove the sheet metal screws installed e arlier. Drill 3/8” holes through the doorframe, floor, and vehicle. Attach using 3/8” x 2” hex head bolts, washers, fender washers, lock washers, and hex nuts. Item #6 to van floor On 3 rd Compartment Doorfram ...

  • Havis-Shields KK-100-06 - page 19

    KK-XXX-06_INST_8-07 19 Socket Ball Item #14 to doors and frames Attach Ball & Socket Style Doorstop. 1 st Attach “Ball” portion of assembly. Attach to threaded hole on the doo r using a ¼” x 1” Hex head bolt. nd 2 Attach the “Socket” and brack et portion. Attach to doorframe using #8 x ¾” Phillips machine screws and keps nuts. S ...

  • Havis-Shields KK-100-06 - page 20

    KK-XXX-06_INST_8-07 20 Optional Storage Compartm ent (Sold Seperatley) FINAL INSTALLATION PHOTOS Optional Storage Compartm ent (Sold Separately) ...

  • Havis-Shields KK-100-06 - page 21

    KK-XXX-06_INST_8-07 21 PT-VIDEO-X C-VS-1800-ECO w/ C-TCB-7 & C-3090-7 K K -RLL KK-PV ENT K R -CCL-1 KR-DL PRISONER TRANSPORT OPTIONS – (A ll SOLD SEPERATLEY ) ...

  • Havis-Shields KK-100-06 - page 22

    Item 3 Item 7 Item 12 Item 1 Item 8 Item 10 Item 6 Item 2 Item 4 Item 9 Item 11 Item 14 Item 15 Item 5 Item 14 Item 13 ITEM DESCRIPTION 1 Driver-side Bench/Wall 2 Passenger-side Bench/Wall 3 Front Bulkhead 4 Diamond-plate Floor 5 Divider 6 Rear Bulkhead/ Doorframe 7 Driver-side Ceiling 8 Passenger-side Rear Ceiling 9 3 rd Compartment Bulkhead 10 3 ...

Manufacturer Havis-Shields Category Automobile Accessories

Documents that we receive from a manufacturer of a Havis-Shields KK-100-06 can be divided into several groups. They are, among others:
- Havis-Shields technical drawings
- KK-100-06 manuals
- Havis-Shields product data sheets
- information booklets
- or energy labels Havis-Shields KK-100-06
All of them are important, but the most important information from the point of view of use of the device are in the user manual Havis-Shields KK-100-06.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Havis-Shields KK-100-06, service manual, brief instructions and user manuals Havis-Shields KK-100-06. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Havis-Shields KK-100-06.

Similar manuals

A complete manual for the device Havis-Shields KK-100-06, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Havis-Shields KK-100-06 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Havis-Shields KK-100-06.

A complete Havis-Shields manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Havis-Shields KK-100-06 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Havis-Shields KK-100-06, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Havis-Shields KK-100-06, that we can find in the current document
3. Tips how to use the basic functions of the device Havis-Shields KK-100-06 - which should help us in our first steps of using Havis-Shields KK-100-06
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Havis-Shields KK-100-06
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Havis-Shields KK-100-06 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Havis-Shields KK-100-06?

Use the form below

If you did not solve your problem by using a manual Havis-Shields KK-100-06, ask a question using the form below. If a user had a similar problem with Havis-Shields KK-100-06 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (1)

Anatoly Medvedev

Not possible to connect with any other telephone. Only short rings are sounded.