English dropdown-ico

Manual Pelco IV SE

80 pages 1.71 mb
Download

Go to site of 80

Summary
  • Pelco IV SE - page 1

    C3434M-A (9/07) Spectra ® IV SE Horizon Series Dome Drive INSTALLATION/OPERATION ...

  • Pelco IV SE - page 2

    ...

  • Pelco IV SE - page 3

    C3434M-A (9/07) 3 Contents Welcome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Pelco IV SE - page 4

    4 C3434M-A (9/07) Shutter Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 AGC Limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Pelco IV SE - page 5

    C3434M-A (9/07) 5 Clear Event . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 List Event . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Pelco IV SE - page 6

    6 C3434M-A (9/07) W elcome Thank you for purchasing Pelco’ s premier look up integrated dome system, Spectra ® IV SE Horizon. Y our new system features a high resolution camera/optics package with programmable dome drive software, and the ability to view scenes 18 degrees above the horizon. With the ability to view scenes above the horizon, the ...

  • Pelco IV SE - page 7

    C3434M-A (9/07) 7 Installation NOTES: • Please refer to the Important Note shipped with the dome drive before installing the back box, dome drive, or lower dome. The Important Note contains vital information about managing the bubble seam. • This manual contains installation instructions only for the Spectra IV SE Horizon dome drive. For comple ...

  • Pelco IV SE - page 8

    8 C3434M-A (9/07) SW2 SWITCHES 1-3: SPECIAL SYSTEM SETTINGS AD-32 Preset System SW2-1 should be set to the ON position if an AD-32 controller and Pelco’ s TXB-AD translator board are used to control the dome system. CM9502 Setting If a CM9502 matrix system is used with the dome drive, set SW2-2 to the ON position. Vicon System The Vicon ® protoc ...

  • Pelco IV SE - page 9

    C3434M-A (9/07) 9 SW2 Switch 9: Coaxial/UTP Cable SW2-9 should be set to the OFF position (default) if you are using coaxial cable. If you are using unshielded twisted pair (UTP) cable, set SW2-9 to the ON position. SW2 Switch 10: T ermination Setting When connecting more than one Spectra IV SE Horizon dome system to a single controller , terminate ...

  • Pelco IV SE - page 10

    10 C3434M-A (9/07) T able A. Switch Settings for SW1 P-T ype Control SPECTRA ADDRESS SWITCH SETTING SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 1 OFF OFF OFF OFF OFF OFF OFF OFF 2 ON OFF OFF OFF OFF OFF OFF OFF 3 OFF ON OFF OFF OFF OFF OFF OFF 4 ON ON OFF OFF OFF OFF OFF OFF 5 OFF OFF ON OFF OFF OFF OFF OFF 6 ON OFF ON OFF OFF OFF OFF OFF 7 OFF ...

  • Pelco IV SE - page 11

    C3434M-A (9/07) 11 T able B. Switch Settings for SW1 D-T ype Control SPECTRA ADDRESS SWITCH SETTING SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 1 ON OFF OFF OFF OFF OFF OFF OFF 2 OFF ON OFF OFF OFF OFF OFF OFF 3 ON ON OFF OFF OFF OFF OFF OFF 4 OFF OFF ON OFF OFF OFF OFF OFF 5 ON OFF ON OFF OFF OFF OFF OFF 6 OFF ON ON OFF OFF OFF OFF OFF 7 ON ON ...

  • Pelco IV SE - page 12

    12 C3434M-A (9/07) 36 OFF OFF ON OFF OFF ON OFF OFF 37 ON OFF ON OFF OFF ON OFF OFF 38 OFF ON ON OFF OFF ON OFF OFF 39 ON ON ON OFF OFF ON OFF OFF 40 OFF OFF OFF ON OFF ON OFF OFF 41 ON OFF OFF ON OFF ON OFF OFF 42 OFF ON OFF ON OFF ON OFF OFF 43 ON ON OFF ON OFF ON OFF OFF 44 OFF OFF ON ON OFF ON OFF OFF 45 ON OFF ON ON OFF ON OFF OFF 46 OFF ON ON ...

  • Pelco IV SE - page 13

    C3434M-A (9/07) 13 71 ON ON ON OFF OFF OFF ON OFF 72 OFF OFF OFF ON OFF OFF ON OFF 73 ON OFF OFF ON OFF OFF ON OFF 74 OFF ON OFF ON OFF OFF ON OFF 75 ON ON OFF ON OFF OFF ON OFF 76 OFF OFF ON ON OFF OFF ON OFF 77 ON OFF ON ON OFF OFF ON OFF 78 OFF ON ON ON OFF OFF ON OFF 79 ON ON ON ON OFF OFF ON OFF 80 OFF OFF OFF OFF ON OFF ON OFF 81 ON OFF OFF O ...

  • Pelco IV SE - page 14

    14 C3434M-A (9/07) 106 OFF ON OFF ON OFF ON ON OFF 107 ON ON OFF ON OFF ON ON OFF 108 OFF OFF ON ON OFF ON ON OFF 109 ON OFF ON ON OFF ON ON OFF 110 OFF ON ON ON OFF ON ON OFF 111 ON ON ON ON OFF ON ON OFF 112 OFF OFF OFF OFF ON ON ON OFF 113 ON OFF OFF OFF ON ON ON OFF 114 OFF ON OFF OFF ON ON ON OFF 115 ON ON OFF OFF ON ON ON OFF 116 OFF OFF ON O ...

  • Pelco IV SE - page 15

    C3434M-A (9/07) 15 141 ON OFF ON ON OFF OFF OFF ON 142 OFF ON ON ON OFF OFF OFF ON 143 ON ON ON ON OFF OFF OFF ON 144 OFF OFF OFF OFF ON OFF OFF ON 145 ON OFF OFF OFF ON OFF OFF ON 146 OFF ON OFF OFF ON OFF OFF ON 147 ON ON OFF OFF ON OFF OFF ON 148 OFF OFF ON OFF ON OFF OFF ON 149 ON OFF ON OFF ON OFF OFF ON 150 OFF ON ON OFF ON OFF OFF ON 151 ON ...

  • Pelco IV SE - page 16

    16 C3434M-A (9/07) 176 OFF OFF OFF OFF ON ON OFF ON 177 ON OFF OFF OFF ON ON OFF ON 178 OFF ON OFF OFF ON ON OFF ON 179 ON ON OFF OFF ON ON OFF ON 180 OFF OFF ON OFF ON ON OFF ON 181 ON OFF ON OFF ON ON OFF ON 182 OFF ON ON OFF ON ON OFF ON 183 ON ON ON OFF ON ON OFF ON 184 OFF OFF OFF ON ON ON OFF ON 185 ON OFF OFF ON ON ON OFF ON 186 OFF ON OFF O ...

  • Pelco IV SE - page 17

    C3434M-A (9/07) 17 211 ON ON OFF OFF ON OFF ON ON 212 OFF OFF ON OFF ON OFF ON ON 213 ON OFF ON OFF ON OFF ON ON 214 OFF ON ON OFF ON OFF ON ON 215 ON ON ON OFF ON OFF ON ON 216 OFF OFF OFF ON ON OFF ON ON 217 ON OFF OFF ON ON OFF ON ON 218 OFF ON OFF ON ON OFF ON ON 219 ON ON OFF ON ON OFF ON ON 220 OFF OFF ON ON ON OFF ON ON 221 ON OFF ON ON ON O ...

  • Pelco IV SE - page 18

    18 C3434M-A (9/07) 246 OFF ON ON OFF ON ON ON ON 247 ON ON ON OFF ON ON ON ON 248 OFF OFF OFF ON ON ON ON ON 249 ON OFF OFF ON ON ON ON ON 250 OFF ON OFF ON ON ON ON ON 251 ON ON OFF ON ON ON ON ON 252 OFF OFF ON ON ON ON ON ON 253 ON OFF ON ON ON ON ON ON 254 OFF ON ON ON ON ON ON ON T able B. Switch Settings for SW1 D-T ype Control (Continued) SP ...

  • Pelco IV SE - page 19

    C3434M-A (9/07) 19 Getting Started Once installed, apply power to the Spectra IV SE Horizon dome system. The system will start a configuration sequence. When configuration is done, the following information is displayed: Pelco Spectra IV SE Horizon V ersion X.XX D Address: 1 P Address: 2 Comm 2400, N, 8, 1 CONFIGURE DONE This information will rem ...

  • Pelco IV SE - page 20

    20 C3434M-A (9/07) How to Operate Y our Dome System Operation How to Control Pan and T ilt Move joystick or press the direction keys left/right and up/down. Zoom Far T o zoom far , do the following: 1. Press the Zoom T ele button or turn the joystick clockwise until zoom stops at the optical zoom limit. 2. Release the button or joystick for one sec ...

  • Pelco IV SE - page 21

    C3434M-A (9/07) 21 QUICK PROGRAMMING GUIDE Access main menu (preset 95). See the Accessing Main Menu (Preset 95) section. Use the joystick to position the cursor beside menu selection. NOTE: If your controller does not have a joystick, use the up or down key . Press Iris Open, the submenu/cursor moves to the right. Move the joystick up or down to v ...

  • Pelco IV SE - page 22

    22 C3434M-A (9/07) CM9500 1. Enter the number of the Spectra IV SE Horizon dome system and press the CAM key . The main menu appears. 2. Highlight SETUP in the main menu and press the SELECT key . 3. Highlight CAM in the Setup menu and press the SELECT key . 4. Highlight PRESET in the Camera menu and press the SELECT key . 5. Enter 95 and press the ...

  • Pelco IV SE - page 23

    C3434M-A (9/07) 23 NET300/NET350/NET4001A 1. Check the Set box. 2. Click the preset 95 button. The main menu appears. ENDURA W ORKSTATION 1. Right-click in the video pane of the Spectra IV SE Horizon dome system. 2. Click Preset and then click Select Preset. 3. Enter 95 and then click OK. VCD5000 1. Enter 95 for the preset action. The shortcuts men ...

  • Pelco IV SE - page 24

    24 C3434M-A (9/07) Spectra IV SE Horizon Menu T ree LANGUAGE ENGLISH <SYSTEM INFORMA TION> <DISPLA Y SETUP> <DOME SETTINGS> PELCO SPECTRA IV SE HORIZON ADVANCED SETTINGS MOTION POWER UP ACTION AUTO POWER UP TYPE OF LIGHTING OUTDOOR AUTO FOCUS ON ZOOM LIMIT XXXX ZOOM SPEED XXXX LOW LIGHT LIMIT IR CUT FIL TER XXXXXX XXXX AUTO AUTO I ...

  • Pelco IV SE - page 25

    C3434M-A (9/07) 25 DETECTION AREA 1 LOCA TION 0 SENSITIVITY MEDIUM DETECTION AREA 2 LOCA TION SENSITIITY 0 MEDIUM 0 MEDIUM 0 MEDIUM DETECTION AREA 3 LOCA TION SENSITIVITY DETECTION AREA 4 LOCA TION SENSITIVITY EDIT DETECTION AREAS LINE SYNC ON LINE SYNC PHASE 0 LINE SYNC RESUME OFF 5 0 SEQUENCE (SECS) RESET DELA Y (SECS) <ALARM SETTINGS> ALAR ...

  • Pelco IV SE - page 26

    26 C3434M-A (9/07) Language The language for the on-screen menus is selectable. Available languages include English, Spanish, French, German, Italian, Portuguese, Russian, Polish, T urkish, and Czech. The factory default language is English. T o change the display language: 1. Use the joystick to position the cursor beside LANGUAGE. 2. Press Iris O ...

  • Pelco IV SE - page 27

    C3434M-A (9/07) 27 System Information The System Information screen displays dome drive model, software version, available memory , and other diagnostic information. System settings cannot be changed using this screen. This screen is for reference only . Use the following steps to display the System Information screen: 1. Use the joystick to positi ...

  • Pelco IV SE - page 28

    28 C3434M-A (9/07) Display Setup Display setup allows you to program how labels are displayed on the monitor . The following labels are available: PRESET LABEL Identifies preset. ZONE LABEL Identifies zone. ZOOM Identifies the amount of magnification. AZIMUTH 1 /ELEVATION 2 Amount of pan from zero degrees vertical and the amount of tilt from ze ...

  • Pelco IV SE - page 29

    C3434M-A (9/07) 29 LABEL POSITIONS Labels can be placed anywhere on the monitor . This feature allows you to customize the appearance of your monitor screen. The following labels are not set at fixed positions: PRESET LABEL ZONE LABEL ALARM 1 ZOOM RA TIO - XXX.XX AZIMUTH 1 /ELEV A TION 2 - XXX°/-XX° DIRECTION - NE EVENT LABEL T o set a label pos ...

  • Pelco IV SE - page 30

    30 C3434M-A (9/07) Dome Settings CAMERA T YPE OF LIGHTING Pelco has calibrated settings that optimize the white balance and the picture for indoor and outdoor lighting conditions. There are two settings: OUTDOOR (default) INDOOR AUTO FOCUS Auto focus allows the lens to remain in focus during zoom-in, zoom-out, and motion functions. There are two au ...

  • Pelco IV SE - page 31

    C3434M-A (9/07) 31 ZOOM LIMIT Zoom limit allows the user to define a limitation on the amount of telephoto zoom. The settings vary depending on camera model.The default setting is 70X. Cameras with 420X zoom (35X optical zoom and 12X digital zoom) can be set for 35X, 70X, 140X, 280X, 350X, or 420X ZOOM SPEED Zoom speed allows the user to define h ...

  • Pelco IV SE - page 32

    32 C3434M-A (9/07) IR CUT FILTER The camera have two modes of operation: color , and black-white. Y ou can increase sensitivity in low light conditions by switching to black-white mode (removing the IR cut filter). Color mode is preferred in normal lighting conditions. The following are the settings for the IR cut filter: OFF Manual operation is ...

  • Pelco IV SE - page 33

    C3434M-A (9/07) 33 ADVANCED CAMERA SETTINGS SHUTTER SPEED Shutter speed is the duration of the electronic shutter . Program shutter speed to operate automatically (Auto) or manually (Numeric V alue). AUTO (default) The electronic shutter speed is set automatically by the amount of light sensed by the camera. NUMERIC V ALUE Spectra IV SE Horizon dom ...

  • Pelco IV SE - page 34

    34 C3434M-A (9/07) AUTO IRIS Auto iris is the lens function that automatically opens and closes the iris in response to changing light conditions. Program the auto iris to operate automatically or at a user -defined level. OFF Auto iris is disabled, and control is always manual. AUTO (default) The iris is adjusted automatically to produce a consta ...

  • Pelco IV SE - page 35

    C3434M-A (9/07) 35 AUTO SHARPNESS Auto sharpness enhances picture detail by increasing the aperture gain of the camera and sharpening the edges in the picture. There are two settings: ON (default) The camera automatically maintains a normal sharpness mode. OFF The sharpness of the picture is set manually by programming the sharpness level. Sharpnes ...

  • Pelco IV SE - page 36

    36 C3434M-A (9/07) BACKLIGHT COMPENSATION (BLC) If a bright backlight is present, the subjects in the picture may appear dark or as a silhouette. Backlight compensation enhances objects in the center of the picture. The dome uses the center of the picture to adjust the iris. If there is a bright light source outside of this area, it will wash out t ...

  • Pelco IV SE - page 37

    C3434M-A (9/07) 37 VIDEO LEVEL Set the video output to one of the following: NORMAL 1.0 volt peak-to-peak HIGH (default setting) 1.2 volt peak-to-peak to compensate for losses in video cable. WIDE DYNAMIC RANGE Wide dynamic range (WDR) balances the brightest and darkest sections of a scene to produce a picture that is better balanced in lighting an ...

  • Pelco IV SE - page 38

    38 C3434M-A (9/07) ELECTRONIC IMAGE STABILIZATION Electronic image stabilization is a feature of the camera that can compensate for some forms of external influences. In all cases, care should be taken to make sure that any dome system is mounted to a rigid location. In the event that vibration is introduced to the dome system, a user can select o ...

  • Pelco IV SE - page 39

    C3434M-A (9/07) 39 MOTION SETTINGS AUTO FLIP When the camera tilts downward and goes just beyond the vertical position, the dome rotates 180 degrees. When the dome rotates (flips), the camera starts moving upward as long as you continue to hold the joystick in the down position. Once you let go of the joystick after the dome rotates, joystick cont ...

  • Pelco IV SE - page 40

    40 C3434M-A (9/07) PARK T IME This feature allows the dome to begin a specified operation (scan, preset, or pattern) after a programmed time of inactivity . Park time can be programmed from 1 minute to 720 minutes (12 hours), or set to zero, which disables this feature. The default setting is zero. Park Action This feature will define the activit ...

  • Pelco IV SE - page 41

    C3434M-A (9/07) 41 SCAN SPEED Scan speed is the degrees per second that the dome will pan when in a scan mode. Scan speed is adjustable from 1 to 40 degrees per second through the programming menu. The default setting is 25 degrees per second. PRESET FREEZE FRAME This feature freezes the scene on the monitor when going to a preset. This allows for ...

  • Pelco IV SE - page 42

    42 C3434M-A (9/07) LIMIT STOPS Limit stops are programmable stops that limit the pan range of the dome. There must be two limits, a left and a right, to define an area. There are two types of limit stops: MANUAL A manual (joystick) pan operation stops when a limit stop is reached. SCAN The dome reverses direction during random, frame, or auto scan ...

  • Pelco IV SE - page 43

    C3434M-A (9/07) 43 AZIMUTH ZERO Azimuth is the pan angle from zero to 359 degrees. Azimuth zero is the pan position you specify to be the zero degree point. Azimuth zero is normally set to magnetic north. Once set, azimuth and compass readings are based on the set Azimuth Zero point. T o program azimuth zero: 1. Use the joystick to position the cur ...

  • Pelco IV SE - page 44

    44 C3434M-A (9/07) POWER UP POWER UP ACTION This setting defines a specific activity (scan, preset, pattern) to be performed in the event the power to the dome is cycled. The following settings are available: NONE No action. AUTO (default) The dome resumes its prior activity or direction before the power outage. AUTO SCAN Dome starts auto scan op ...

  • Pelco IV SE - page 45

    C3434M-A (9/07) 45 LINE SYNC Line sync refers to a programmable function that allows you to synchronize all cameras within a matrix system. NOTE: Spectra IV SE Horizon dome systems automatically sense V-Sync input. No line sync setup is required for Pelco control systems that provide a V-Sync signal. For matrix systems that do not output V-Sync, th ...

  • Pelco IV SE - page 46

    46 C3434M-A (9/07) PRESETS NOTE: The model of the back box you are using limits the number of programmable presets that can be stored and retrieved in the back box memory . If you are using an older model back box, you may program and use up to the maximum number of presets available to the dome drive. However , if the dome drive is changed, the ba ...

  • Pelco IV SE - page 47

    C3434M-A (9/07) 47 NOTE: For American Dynamics controllers with only 32 presets, switch SW2-1 on the dome drive to the ON position. When SW2-1 is ON, preset 99 becomes 32 92 becomes 25 98 becomes 31 91 becomes 24 97 becomes 30 90 becomes 23 96 becomes 29 89 becomes 22 95 becomes 28 88 becomes 21 93 becomes 26 If the limit stops are turned off, pres ...

  • Pelco IV SE - page 48

    48 C3434M-A (9/07) 4. Edit preset camera settings: a. Use the joystick to position the cursor beside EDIT CAMERA SETTINGS. b. Press Iris Open. The EDIT CAMERA SETTINGS window appears on the monitor . Refer to the Camera and Advanced Camera Settings sections of this manual to change preset camera settings. c. T o edit the camera settings schedule, u ...

  • Pelco IV SE - page 49

    C3434M-A (9/07) 49 ENABLE MOTION DETECTION The following are the settings for motion detection: OFF (default) Motion detection is turned off (disabled). ON Motion detection is turned on (enabled). NOTE: Motion detection does not work if the shutter speed is set at less than 1/60 of a second. EDIT DETECTION AREAS Four motion detection areas can be d ...

  • Pelco IV SE - page 50

    50 C3434M-A (9/07) NOTE: Motion detection is not guaranteed to catch 100% of activity . EDIT DETECTION AREAS DETECTION AREA 1 LOCA TION 0 SENSITIVITY MEDIUM DETECTION AREA 2 LOCA TION 0 SENSITIVITY MEDIUM DETECTION AREA 3 LOCA TION 0 SENSITIVITY MEDIUM DETECTION AREA 4 LOCA TION 0 SENSITIVITY MEDIUM BACK EXIT MOTION DETECTION AREAS ...

  • Pelco IV SE - page 51

    C3434M-A (9/07) 51 ACTIVATE AUX COMMAND Motion detection can be programmed to trigger an auxiliary command when motion is detected. The following are the settings for ACTIV A TE AUX: OFF (default) Motion detection will not trigger an AUX command. 1 T riggers a command to AUX 1. 2 T riggers a command to AUX 2. AUX T IME Aux time is the length of tim ...

  • Pelco IV SE - page 52

    52 C3434M-A (9/07) PATTERNS A pattern is a memorized, repeating series of pan, tilt, zoom, and preset functions that can be recalled with a command from a controller or automatically by a programmed function (alarm, park, event, or power -up). The Spectra IV SE Horizon can handle up to eight patterns. Pattern length is based upon memory usage rathe ...

  • Pelco IV SE - page 53

    C3434M-A (9/07) 53 ZONES A zone is a pan area, defined by a left and right limit, on the 360-degree pan plane. Spectra IV SE Horizon dome systems are capable of eight zones, each with a 20-character label. T o program a zone: 1. Use the joystick to position the cursor beside ZONE NUMBER. Press Iris Open, and the cursor moves to the right. 2. Move ...

  • Pelco IV SE - page 54

    54 C3434M-A (9/07) WINDOW BLANKING Window blanking allows a user to program four -sided areas that cannot be viewed by the operator of the dome system. A blanked area will move with pan and tilt functions and automatically adjust in size as the lens zooms telephoto and wide. The Spectra IV SE Horizon dome system has eight available user -defined w ...

  • Pelco IV SE - page 55

    C3434M-A (9/07) 55 6. The blanked area can be programmed to turn on or off at a specified zoom point. T o set the zoom point: a. Use the joystick to position the cursor beside EDIT WINDOW ZOOM, and then press Iris Open. b. Zoom in to the point where you want window blanking to turn on. Press Iris Open to set the zoom point. NOTES: • Since the ar ...

  • Pelco IV SE - page 56

    56 C3434M-A (9/07) BLANK ALL ABOVE/BLANK ALL BELOW The Blank All Above and Blank All Below options add additional flexibility to setting up privacy areas. These settings are ideal for applications where a complete pan location needs to be blanked. Blank All Above blanks everything above a user -defined tilt angle. A blanked band will appear at th ...

  • Pelco IV SE - page 57

    C3434M-A (9/07) 57 ALARMS The Spectra IV SE Horizon dome system has seven alarm inputs that can be programmed as high, medium, or low priority . When an alarm is received, an input signal to the dome triggers the user - defined action (go to preset, run pattern, etc.) programmed for the alarm. There are three global alarm settings: RESUME This mod ...

  • Pelco IV SE - page 58

    58 C3434M-A (9/07) 3. Select the alarm priority: a. Use the joystick to position the cursor beside ALARM PRIORITY . b. Press Iris Open. The cursor moves to the right. c. Move the joystick up or down to view the available selections. Available settings include HIGH, MEDIUM, and LOW (default). If multiple alarms with different priorities are active a ...

  • Pelco IV SE - page 59

    C3434M-A (9/07) 59 5. Set the auxiliary to activate: a. Use the joystick to position the cursor beside ACTIV A TE AUX. b. Press Iris Open. The cursor moves to the right. c. Move the joystick up or down to view the following available selections. NO (default) Not activated. 1 An alarm action will close AUX 1. 2 An alarm action will close AUX 2. d. P ...

  • Pelco IV SE - page 60

    60 C3434M-A (9/07) AUX An auxiliary output is a programmable signal from the dome back box that can trigger another device to operate. An auxiliary output is programmable to trigger from an alarm or from a controller . An AUX 1 command from the controller will activate the relay in the dome and operate the device that is connected to the relay . Th ...

  • Pelco IV SE - page 61

    C3434M-A (9/07) 61 T ITLE T EXT T itle text is the label used to identify the camera viewed on the monitor . Up to 20 characters can be used for a title. T o edit the title text label, do the following: 1. Use the joystick to position the cursor beside EDIT TITLE TEXT . 2. Press Iris Open. The following appears on the monitor: 3. Use the joystick t ...

  • Pelco IV SE - page 62

    62 C3434M-A (9/07) CLEAR Use this setting to clear user -defined settings or return the dome to factory default settings. The following are the available settings: ALL ZONES Clears all zones. T o clear a single zone, refer to the Zones section on page 53. ALL PRESETS Clears all presets. T o clear a single preset, refer to the Presets section on pa ...

  • Pelco IV SE - page 63

    C3434M-A (9/07) 63 PASSWORD The Spectra IV SE Horizon features password protection to prevent unauthorized changes to the dome settings. An operator can open the System Information and Display Setup screens, but cannot access any of the dome settings menus. Controller/keyboard commands cannot override password-protected settings. If a keyboard is u ...

  • Pelco IV SE - page 64

    64 C3434M-A (9/07) CLOCK The clock is used to program the current date and time. The date and time set in the Clock menu is used to program events. The date and time can also be displayed on the monitor when the menus are not being accessed (refer to Display Setup on page 28). T o program the clock, do the following: 1. Use the joystick to position ...

  • Pelco IV SE - page 65

    C3434M-A (9/07) 65 7. If FIXED DA TE was selected, the following appears on the monitor: a. Use the joystick to position the cursor beside TIME SHIFT . Press Iris Open. Scroll through the options until the desired selection appears. Press Iris Open to select the time shift. b. Use the joystick to position the cursor beside the start date MONTH. Pre ...

  • Pelco IV SE - page 66

    66 C3434M-A (9/07) 8. If RELA TIVE DA TE was selected, the following appears on the monitor: Follow the instructions in step 7 for FIXED DA TE, adding WEEK. CLOCK TIME BASE INTERNAL CLOCK TIME FORMA T 12 HOUR SET TIME 00:00 AM DA TE FORMA T MM/DD/YYYY SET DA TE 00/00/0000 DA YLIGHT SAVINGS RELA TIVE DA TE TIME SHIFT 1 HOUR ST ART DA TE MONTH APRIL ...

  • Pelco IV SE - page 67

    C3434M-A (9/07) 67 EVENT An event is a preprogrammed camera, park, scan, preset, pattern, window blanking, alarm, or auxiliary function that can be performed automatically at a specific date and time. For example, suppose a camera is set to run in a continuous pattern that scans a parking lot during business hours Monday through Friday . On Saturd ...

  • Pelco IV SE - page 68

    68 C3434M-A (9/07) EDIT EVENT LABEL After an event has been programmed, the label can be changed using the following steps: 1. Use the joystick to position the cursor beside EDIT EVENT LABEL. 2. Press Iris Open. The following appears on the monitor: 3. Use the joystick to position the cursor beside a character . Press Iris Open to enter selection. ...

  • Pelco IV SE - page 69

    C3434M-A (9/07) 69 EDIT EVENT Use the following steps to edit an event. 1. Use the joystick to position the cursor beside EDIT EVENT . 2. Press Iris Open. The following appears on the monitor: a. Use the joystick to position the cursor beside EVENT ACTIVE. Press Iris Open. Scroll to select NO to leave the event inactive or YES to activate the event ...

  • Pelco IV SE - page 70

    70 C3434M-A (9/07) CLEAR EVENT T o clear an event: 1. Use the joystick to position the cursor beside CLEAR EVENT . 2. Press Iris Open. 3. Follow the directions displayed on the monitor . LIST EVENT T o list events: 1. Use the joystick to position the cursor beside LIST EVENT . 2. Press Iris Open. 3. All programmed events will be listed. HOLIDAY Use ...

  • Pelco IV SE - page 71

    C3434M-A (9/07) 71 EDIT HOLIDAY Use the following steps to edit a holiday: 1. Use the joystick to position the cursor beside EDIT EVENT LABEL. 2. Press Iris Open. 3. Use the joystick to position the cursor beside OCCURRENCE. Press Iris Open. The following are the settings for Occurrence: FIXED DA TE Holiday occurs on the same date each year . RELA ...

  • Pelco IV SE - page 72

    72 C3434M-A (9/07) CLEAR HOLIDAY T o clear a holiday: 1. Use the joystick to position the cursor beside CLEAR HOLIDA Y . 2. Press Iris Open. 3. Follow the directions displayed on the monitor . LIST HOLIDAYS T o list events: 1. Use the joystick to position the cursor beside LIST HOLIDA YS. 2. Press Iris Open. 3. All programmed holidays will be liste ...

  • Pelco IV SE - page 73

    C3434M-A (9/07) 73 SCHEDULED EVENTS Use this page to record scheduled events. ________________________________________________________________________________________ ________________________________________________________________________________________ ________________________________________________________________________________________ _____ ...

  • Pelco IV SE - page 74

    74 C3434M-A (9/07) Reset, Cycle Power , Reboot RESET CAMERA Use this function to reset all camera settings to factory default parameters. CYCLE CAMERA POWER If the camera is not operating or if you lose camera control, cycle camera power . Cycling camera power resets the camera but does not change any saved camera settings. REBOOT SYSTEM Reboot the ...

  • Pelco IV SE - page 75

    C3434M-A (9/07) 75 Software/Language File Upload The RJ-45 data port of the dome drive allows access for on-site setup, testing, and uploading of revised operating software and language files. A Pelco field service tool is required to perform these operations. Field service tools include Pelco’ s remote monitor kit (IPS-RMK), remote data port b ...

  • Pelco IV SE - page 76

    76 C3434M-A (9/07) Suggested Preventative Maintenance The Spectra IV SE Horizon dome systems do not require any special maintenance. Occasionally , dust may build up on the inside or the outside of the dome. If this occurs, turn power to the unit off and remove the lower dome from the back box. Remove the dust from the lower dome using compressed a ...

  • Pelco IV SE - page 77

    C3434M-A (9/07) 77 Specifications DD4H35 Signal Format NTSC Scanning System 2:1 Interlace Image Sensor 1/4-inch CCD Effective Pixels 768 (H) X 494 (V) Horizontal Resolution > 540 TV lines Lens f/1.4 (focal length, 3.4~119 mm; 35X optical zoom, 12X digital zoom) Zoom Speed (optical range) 3.2/4.6/6.6 seconds Horizontal Angle of View 55.8° at 3. ...

  • Pelco IV SE - page 78

    78 C3434M-A (9/07) DD4H35-X Signal Format P AL Scanning System 2:1 Interlace Image Sensor 1/4-inch CCD Effective Pixels 752 (H) X 582 (V) Horizontal Resolution > 540 TV lines Lens f/1.4 (focal length, 3.4~119 mm; 35X optical zoom, 12X digital zoom) Zoom Speed 3.2/4.6/6.6 seconds Horizontal Angle of View 55.8° at 3.4 mm wide zoom; 1.7° at 119 m ...

  • Pelco IV SE - page 79

    PRODUCT WARRANTY AND RETURN INFORMA TION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on fiber optic products and TW3000 Series unshielded twisted pair transmissio ...

  • Pelco IV SE - page 80

    W orldwide Headquarters 3500 Pelco W ay Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www .pelco.com ISO 9001 Australia | Canada | Finland | France | Germany | Italy | Macau | The Netherlands | Russia | Singapore South Africa | Spain | Sweden | United Arab E ...

Manufacturer Pelco Category Home Security System

Documents that we receive from a manufacturer of a Pelco IV SE can be divided into several groups. They are, among others:
- Pelco technical drawings
- IV SE manuals
- Pelco product data sheets
- information booklets
- or energy labels Pelco IV SE
All of them are important, but the most important information from the point of view of use of the device are in the user manual Pelco IV SE.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Pelco IV SE, service manual, brief instructions and user manuals Pelco IV SE. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Pelco IV SE.

Similar manuals

A complete manual for the device Pelco IV SE, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Pelco IV SE by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Pelco IV SE.

A complete Pelco manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Pelco IV SE - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Pelco IV SE, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Pelco IV SE, that we can find in the current document
3. Tips how to use the basic functions of the device Pelco IV SE - which should help us in our first steps of using Pelco IV SE
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Pelco IV SE
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Pelco IV SE in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Pelco IV SE?

Use the form below

If you did not solve your problem by using a manual Pelco IV SE, ask a question using the form below. If a user had a similar problem with Pelco IV SE it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)