English dropdown-ico

Manual JAI CV-M300

24 pages 0.6 mb
Download

Go to site of 24

Summary
  • JAI CV-M300 - page 1

    Opera tion Manual Industrial Monochrome CCD Camera (Rev.E) CV -M300 ...

  • JAI CV-M300 - page 2

    CV -M300 DECL ARA TION OF CONFORMIT Y AS D EFINE D B Y THE C O UN CI L D IREC T I VE 89/336/EEC E MC (E LECTR OMAG N E TIC C OMP A TI B ILITY ) WE HE R E WITH DECLAR E THA T TH IS PRODUCT C OM PLI E S WITH THE FOLL OWI NG PR OVISIONS APPL YI NG T O IT . E N-50081-1 E N-50082-1 ...

  • JAI CV-M300 - page 3

    - 2 - CV -M300 T able of Contents T able of Contents .............................................................................................................. ......................... 2 1 . General ................................................................................................................................................ 3 ...

  • JAI CV-M300 - page 4

    - 3 - CV -M300 1. General The CV -M300 is a monochrome 2/3" CCD camer a designed for automated imaging applications featuring high performance and unique functions within a uniform and compact housing. The high-speed shutter function and asynchronous random trigger function allow the camera to capture high quality images of fast moving objects ...

  • JAI CV-M300 - page 5

    - 4 - CV -M300 4. Locations and F unctions 1 2/3" interline transfer CCD sensor. 2 Lens mount of C-mount type. *1) 3 BNC connector for video output. 4 Switch block SW1 for shutter speed and function modes setting. 5 6-pin multi connector for WEN and EEN output external trigger input. 6 12-pin multi connector for +12V DC power , video output an ...

  • JAI CV-M300 - page 6

    - 5 - CV -M300 5. Pin Assignment 5.1. 12-pin Multi-connector (DC-IN/SYNC.) T ype: HR10A-10R-12PB-01 (Hirose) male Seen from rear. Notes: *1 ) Signals on pin no. 6, 7 and 9 can be changed by jumper setting. See “7.3. Jumper Settings” for more information. *2 ) In Edge Pre-select and Pulse Width Control mode do not input ext. VD signal. 5.2. 6-pi ...

  • JAI CV-M300 - page 7

    - 6 - CV -M300 6. F unctions and Operations 6.1. Input/Output of HD/VD Signal 6.1.1. Input of External HD/VD Signal As factory setting the camera can be synchronized by external HD/VD signals. The signal level must be 4.0 Vp-p ± 2.0V at the input with the 75 Ohm termination ON. T o change to non-terminated input, see instructions in “7. Mode Set ...

  • JAI CV-M300 - page 8

    - 7 - CV -M300 T o use this mode Set: SW1-4 to ON for ext. trigger shutter SW1-5 to OFF for field accumulation SW1-6 to ON for non-interlaced SW1-1, 2 and 3 to shutter speed Input: Ext. trigger to pin 5 on 6 pin multi connector. Ext. HD to pin 6 on 12-pin multi connector. (If used). 75 Ohm termination is done with SW2-1 (HD) on PK8041 board. Refer ...

  • JAI CV-M300 - page 9

    - 8 - CV -M300 CCIR (Non-interlaced / Field accumulation mode) 6.3.2. Pulse Width Control Mode The pulse width control mode will only work in non-interlaced field accumulation mode. The exposure is controlled by the lo w period of the ext. trigger pulse. The CV -M300 starts the exposure at the first HD pulse after the falling edge of the ext. trigg ...

  • JAI CV-M300 - page 10

    - 9 - CV -M300 Cautions in the Pulse Width Control Mode. 1. Pulse width control mode is effective only in non-interlaced field accumulation mode. 2. The exposure start may be delayed up to 1H max., when the falling edge of ext. trigger pulse is not synchronized with the falling edge of ext. H D signal. T o avoid this 1H jitter and delay, the fallin ...

  • JAI CV-M300 - page 11

    - 10 - CV -M300 6.3.3. Star t/Stop T rigger Mode The Start /Stop trigger will work in 3 modes: 1. Interlaced with frame accumulation. 2. Interlaced with field accumulation. 3. Non-interlaced with field accumulation. The exposure time is controlled by the interval between the ext. trigger pulse and the ext. VD signal. The exposure starts at the firs ...

  • JAI CV-M300 - page 12

    - 11 - CV -M300 Cautions in the Star t/Stop T rigger Mode. 1. The input of ext. VD signal must be given continuously to synchronize with int. VD signal. It is not possible to input ext. VD signal randomly. 2. The exposure start may delay up to 1H max., when the falling edge of ext. trigger pulse is not synchronized with the falling edge of ext. H D ...

  • JAI CV-M300 - page 13

    - 12 - CV -M300 6.3.4. Long Time Exposure Mode The Long time exposure will work in 3 modes: 1. Interlaced with field accumulation. 2. Interlaced with frame accumulation. 3. Non-interlaced with field accumulation. The exposure time is the interval between 2 ext. VD pulses sent to the camera VD input. Each ext. VD pulse will reset and restart the int ...

  • JAI CV-M300 - page 14

    - 13 - CV -M300 Cautions in the Long Time Exposure Mode. 1. Theoretical exposure time is as follows. EIA: 1/30 sec. to ∞ . CCIR: 1/25 sec. to ∞ . 2. It is recommended not to use exposure > 2 sec. since visible dark-current noise may occur. 3. Ext. HD signal (4.0 Vp-p ± 2.0V at 75 Ohm terminated) has to be input continuously The falling edge ...

  • JAI CV-M300 - page 15

    - 14 - CV -M300 7. Mode Setting Cautions on Mode Setting. Before making any mode or jumper setting turn the po wer OF F . 7.1.1. SW1 Switch on the Rear Panel Factory settings for SW1 are with all 8 switches in OFF position. The shutter values are given for a CCIR camera having the factory settings. Shutter values for other setups and EIA cameras ca ...

  • JAI CV-M300 - page 16

    - 15 - CV -M300 Cautions on Shutter . The image can flicker when the illumination is AC powered. Highlighted parts of the image will show increasing smear at a shorter shutter time. 7.1.4. Ext. T rigger Shutter Mode When trigger select SW1-4 is ON. The camera is in ext. trigger shutter mode. The SW1-1, SW1-2 and SW1- 3 are for selecting the shutter ...

  • JAI CV-M300 - page 17

    - 16 - CV -M300 7.3. Jumper Settings Cautions on Jumper Setting. Before making any mode or jumper setting turn the po wer OF F . Jumpers for mode setting are found on the boards PK8041 & PK8042. The following modes are available with jumper setting: Input/Output Mode of HD/VD signal. (HD/VD input is factory setting) Edge Pre-select Mode. (Facto ...

  • JAI CV-M300 - page 18

    - 17 - CV -M300 7.4. Location of SW2 and Jumpers Jumpers are shorted with a 0 Ohm resistor or b y a soldering between the 2 points. T o remove the solder tin from a jumper position, use a special tin remover such as de-soldering wick. 7.4.1. Board PK8041 Side A 7.4.2. Board PK8042 Side A ...

  • JAI CV-M300 - page 19

    - 18 - CV -M300 8. Adjustment of Video Signal Output Level When an alignment of a video output signal is required, remove the camera housing and adjust potentiometers VR3, VR4 and VR5 on the PK8042 board while measuring their levels at the video output connector. This adjustment should only be done in a setup with a standard TV test chart and contr ...

  • JAI CV-M300 - page 20

    - 19 - CV -M300 9. External Appearance Unit : mm (inches) T ripod mount plate ...

  • JAI CV-M300 - page 21

    - 20 - CV -M300 10. Specifications Scanning system CCIR 625 lines EIA 525 lines 25 frames/sec. 30 frames/sec. CCD sensor Monochrome 2/3" IT CCD Sensing area 8.8 mm (h) x 6.6 mm (v) Effective pixels 752 (h) x 582 (v) 768 (h) x 494 (v) Elements in video output 737 (h) x 575 (v) 758 (h) x 486 (v) Cell size 11.6 (h) x 11.2 (v) µm 11.6 (h) x 13.5 ...

  • JAI CV-M300 - page 22

    - 21 - CV -M300 11. Appendix 11.1. Precautions Personnel not trained in dealing with similar electronic devices should not service this camera. The camera contains components sensitive to electrostatic discharge. The handling of these devices should follow the requirements of electrostatic sensitive components. Do not attempt to disassemble this ca ...

  • JAI CV-M300 - page 23

    - 22 - CV -M300 12. User’s R ecord Camera type: CV -M300 Scanning system: EIA/CCIR Revision: (Revision E) Serial No. ................. Users Mode Settings Users Modifications This manual can be downloaded from: www.jai.com ...

  • JAI CV-M300 - page 24

    JAI America, Inc., USA Suite 450 23046 Avenida de la Carlota Laguna Hills, CA 92653 USA Phone +1 949 472 5900 Fax +1 949 472 5908 www.jai.com JAI Corporation, Japan German Industry Center 1-18-2 Hakusan, Midori-ku Y okohama, Kanagawa 226-0006, Japan Phone +81 45 933 5400 Fax +81 45 931 6142 www.jai-corp.co.jp JAI A·S, Denmark Produktionsvej 1, 260 ...

Manufacturer JAI Category Security Camera

Documents that we receive from a manufacturer of a JAI CV-M300 can be divided into several groups. They are, among others:
- JAI technical drawings
- CV-M300 manuals
- JAI product data sheets
- information booklets
- or energy labels JAI CV-M300
All of them are important, but the most important information from the point of view of use of the device are in the user manual JAI CV-M300.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals JAI CV-M300, service manual, brief instructions and user manuals JAI CV-M300. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product JAI CV-M300.

Similar manuals

A complete manual for the device JAI CV-M300, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use JAI CV-M300 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of JAI CV-M300.

A complete JAI manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual JAI CV-M300 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the JAI CV-M300, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the JAI CV-M300, that we can find in the current document
3. Tips how to use the basic functions of the device JAI CV-M300 - which should help us in our first steps of using JAI CV-M300
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with JAI CV-M300
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of JAI CV-M300 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning JAI CV-M300?

Use the form below

If you did not solve your problem by using a manual JAI CV-M300, ask a question using the form below. If a user had a similar problem with JAI CV-M300 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)