English dropdown-ico

Manual Stanley Black & Decker CS25/28

22 pages 1.95 mb
Download

Go to site of 22

Summary
  • Stanley Black & Decker CS25/28 - page 1

    © 2014 Stanley Black & Decker , Inc. New Britain, CT 06053 U.S.A. 66205 8/2014 V er . 9 USER MANUAL Safety , Operation and Maintenance CS25/28 HYDRAULIC POLE CHAIN SA W ...

  • Stanley Black & Decker CS25/28 - page 2

    2 ► CS25/28 User Manual DECLARATION OF CONF ORMI TY ÜBEREINSTIMM UNGS - ERKLARUNG DECLARATION DE CONFOR MITE CEE DECLARACION DE CONFO RMIDAD DICHIARAZIONE DI CONFORM ITA Hydraulic Tools _______ _________ ___________ ___________ _________ ___________ _________ ___ I, the undersigned: Ich, der Unterzeichnende: Je soussi gné: El abajo firmante: lo ...

  • Stanley Black & Decker CS25/28 - page 3

    CS25/28 User Manual ◄ 3 SERVICING: This manual contains safety , operation, and routine maintenance instructions. Stanley Hydraulic T ools recommends that servicing of hydraulic tools, other than routine maintenance, must be performed by an au- thorized and certied dealer . Please read the following warning. For the nearest authorized and cert ...

  • Stanley Black & Decker CS25/28 - page 4

    4 ► CS25/28 User Manual Always observe safety symbols. They are included for your safety and for the protection of the tool. LOCAL SAFETY REGULA TIONS Enter any local safety regulations here. Keep these instructions in an area accessible to the operator and mainte- nance personnel. Safety symbols and signal words, as shown below , are used to emp ...

  • Stanley Black & Decker CS25/28 - page 5

    CS25/28 User Manual ◄ 5 T ool operators and maintenance personnel must always comply with the safety precautions given in this manual and on the stickers and tags attached to the tool and hose. These safety precautions are given for your safety . Re- view them carefully before operating the tool and before performing general maintenance or repair ...

  • Stanley Black & Decker CS25/28 - page 6

    6 ► CS25/28 User Manual POLE CHAIN SA W SPECIFIC SAFETY PRECAUTIONS • Do not rely exclusively upon the safety devices built into the saw . As a pole saw user , several steps must be taken to keep your cutting jobs free from accident or injury . • With basic understanding of kickback, you can re- duce or eliminate the element of surprise. Sudd ...

  • Stanley Black & Decker CS25/28 - page 7

    CS25/28 User Manual ◄ 7 The following guidelines must be followed to prevent accidental contact with overhead electrical conductors and/or communication wires and cables. (Ref. ANSI Z133.1-2000) WORKING IN PROXIMITY T O ELECTRICAL HAZARDS A n inspection shall be made by a qualied arborist to determine whether an electrical hazard exists before ...

  • Stanley Black & Decker CS25/28 - page 8

    8 ► CS25/28 User Manual T able 2 – Minimum approach distances to energized conductors for persons other than qualied line- clearance arborists and qualied line-clearance ar - borist trainees. Nominal V oltage kV phase-to-phase 1) Distance ft-in m 0.0 – 1.0 10–00 3.05 1.1 – 15.0 10–00 3.05 15.1 – 36.0 10–00 3.05 36.1 – 50.0 1 ...

  • Stanley Black & Decker CS25/28 - page 9

    CS25/28 User Manual ◄ 9 SAFETY T AG P/N 15875 (Shown smaller then actual size) DANGER DANGER READ OPERA TION MANUAL AND SAFETY INSTRUCTIONS FOR THIS TOOL BEFORE USING IT . USE ONL Y P ARTS AND REP AIR PROCEDURES APPROVED BY ST ANLEY AND DESCRIBED IN THE OPERA TION MANUAL. T AG TO BE REMOVED ONL Y BY TOOL OPERA TOR. SEE OTHER SIDE 1. FAILURE TO US ...

  • Stanley Black & Decker CS25/28 - page 10

    10 ► CS25/28 User Manual The rated working pressure of the hydraulic hose must be equal to or higher than the relief valve setting on the hy- draulic system. There are three types of hydraulic hose that meet this requirement and are authorized for use with Stanley Hydraulic T ools. They are: Certied non-conductive — constructed of thermoplas ...

  • Stanley Black & Decker CS25/28 - page 11

    CS25/28 User Manual ◄ 1 1 Oil Flow Hose Lengths Inside Diameter USE ( Press/Return) Min. Working Pressure GPM LPM FEET METERS INCH MM PSI BAR Certied Non-Conductive Hose - Fiber Braid - for Utility Bucket T rucks 4-9 15-34 up to 10 up to 3 3/8 10 Both 2250 155 Conductive Hose - Wire Braid or Fiber Braid -DO NOT USE NEAR ELECTRICAL CONDUCT ORS ...

  • Stanley Black & Decker CS25/28 - page 12

    12 ► CS25/28 User Manual Flow Range Nominal Operating Pressure (at the power supply outlet) System relief valve setting (at the power supply outlet) Maximum back pressure (at tool end of the return hose) Measured at a max. uid viscosity of: (at min. operating temperature) T emperature: Sufcient heat rejection capacity to limit max. uid t ...

  • Stanley Black & Decker CS25/28 - page 13

    CS25/28 User Manual ◄ 13 screw located in the top of the valve spool fully in (clock- wise) until it bottoms. TO DISABLE DUAL SPOOL OPERA TION AND CONVERT TO OC ONL Y OPERA TION T urn the selector screw located in the top of the valve spool fully out (counter-clockwise) until it hits the stop. 1. Insert the small plug from the kit (furnished with ...

  • Stanley Black & Decker CS25/28 - page 14

    14 ► CS25/28 User Manual 4. WARNING W atch for falling limbs. Make a diagonal cut down to meet the horizontal cut and remove the wood from the notch. FELLING OR BACK CUT 5. The felling or back cut is made on the side opposite and at least 2 inches above the horizontal undercut (the felling cut is made higher as the size of the tree increases). 6. ...

  • Stanley Black & Decker CS25/28 - page 15

    CS25/28 User Manual ◄ 15 PRUNING & TRIMMING 1. Observe all safety precautions. 2. Use both hands. Keep a rm grip. 3. Be alert for kickback. Do not allow the tip of the bar to touch anything while the chain is in motion. Figure 3. Crosscutting Logs/Limbs with Pressure on Bottom 4. Pole chain saws must be hung securely in a vertical position ...

  • Stanley Black & Decker CS25/28 - page 16

    16 ► CS25/28 User Manual CHAIN TENSION ADJUSTMENT 1. Observe all safety precautions. 2. When the chain appears loose, lubricate it well and let it cool for a few minutes to allow for contraction of the chain. Disconnect the pole chain saw from its hydraulic power source. NOTE: Perform Steps 3 through 6 while holding the top end of the saw bar upw ...

  • Stanley Black & Decker CS25/28 - page 17

    CS25/28 User Manual ◄ 17 • Make sure all couplers are wiped clean before con- nection. • The hydraulic circuit control valve must be in the OFF position when coupling or uncoupling hydraulic tools. Failure to do so may result in damage to the quick couples and cause overheating of the hydrau- lic system. • Always store the tool in a clean d ...

  • Stanley Black & Decker CS25/28 - page 18

    18 ► CS25/28 User Manual If symptoms of poor performance develop, the following chart can be used as a guide to correct the problem. When diagnosing faults in operation of the pole chain saw , always make sure the hydraulic power source is supply- ing the correct hydraulic ow and pressure as listed in the table. Use a owmeter know to be acc ...

  • Stanley Black & Decker CS25/28 - page 19

    CS25/28 User Manual ◄ 19 Capacity CS25 and CS28 .................................................................................... 12 and 15 inch/30 and 38 cm Cut Lengths Weight (w/o Bar and Chain) ...................................................................................................................... 8.5 lbs/4 kg Overall Length 1 ...

  • Stanley Black & Decker CS25/28 - page 20

    20 ► CS25/28 User Manual T o order complete motor assembly see “Note” on parts list (Page 21). CS25 / CS28 P ARTS ILLUSTRA TION ...

  • Stanley Black & Decker CS25/28 - page 21

    CS25/28 User Manual ◄ 21 ITEM P ART NO. QTY DESCRIPTION 1 19212 1 CAPSCREW 2 65834 1 CHAIN GUARD 3 07631 2 NUT 4 08348 1 SA W CHAIN – 12 INCH 07641 1 SA W CHAIN – 15 INCH 5 66577 1 CHAIN GUIDE PLA TE 6 07630 2 STUD 7 07620 1 BAR ADJUSTMENT NUT 8 07632 1 SCREW 9 04044 2 NEEDLE ROLLER 10 04106 2 DRIVER GEAR (8 GPM) 07832 2 DRIVER GEAR (5 GPM) 1 ...

  • Stanley Black & Decker CS25/28 - page 22

    Stanley Hydraulic T ools 3810 SE Naef Road Milwaukie, Oregon 97267-5698 USA (503) 659-5660 / Fax (503) 652-1780 www .stanleyhydraulics.com ...

Manufacturer Stanley Black & Decker Category Pole Saw

Documents that we receive from a manufacturer of a Stanley Black & Decker CS25/28 can be divided into several groups. They are, among others:
- Stanley Black & Decker technical drawings
- CS25/28 manuals
- Stanley Black & Decker product data sheets
- information booklets
- or energy labels Stanley Black & Decker CS25/28
All of them are important, but the most important information from the point of view of use of the device are in the user manual Stanley Black & Decker CS25/28.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Stanley Black & Decker CS25/28, service manual, brief instructions and user manuals Stanley Black & Decker CS25/28. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Stanley Black & Decker CS25/28.

Similar manuals

A complete manual for the device Stanley Black & Decker CS25/28, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Stanley Black & Decker CS25/28 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Stanley Black & Decker CS25/28.

A complete Stanley Black & Decker manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Stanley Black & Decker CS25/28 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Stanley Black & Decker CS25/28, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Stanley Black & Decker CS25/28, that we can find in the current document
3. Tips how to use the basic functions of the device Stanley Black & Decker CS25/28 - which should help us in our first steps of using Stanley Black & Decker CS25/28
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Stanley Black & Decker CS25/28
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Stanley Black & Decker CS25/28 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Stanley Black & Decker CS25/28?

Use the form below

If you did not solve your problem by using a manual Stanley Black & Decker CS25/28, ask a question using the form below. If a user had a similar problem with Stanley Black & Decker CS25/28 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)