English dropdown-ico

Manual Pfaff Hobbylock 2.5

28 pages Not applicable
Download

Go to site of 28

Summary
  • Pfaff Hobbylock 2.5 - page 1

    Owner’s Manual ...

  • Pfaff Hobbylock 2.5 - page 2

    This household sewing machine is designed to comply with IEC/EN 60335-2-28 and UL1594 IMPORT ANT SAFETY INS TRUCTIONS When using an electrical appliance, basic safety precautions should always be followed, including the following: Read all instructions before using this household sewing machine. D ANGER - T o r educe the risk of electric shock: • ...

  • Pfaff Hobbylock 2.5 - page 3

    3 T able of contents Parts of the machine ................................................................. 4 Accessories .................................................................................... 5 Connecting the foot control and the power supply ..... 5 Setting up the telescopic thread stand ............................. 6 Attaching the ...

  • Pfaff Hobbylock 2.5 - page 4

    4 9 10 11 12 13 1 2 3 4 5 6 14 15 19 16 17 18 7 8 24 21 20 26 25 23 22 P arts of the machine 1. Presser foot pressure adjustment knob 2. Left needle thread tension dial (blue) 3. Right needle thread tension dial (green) 4. Upper looper thread tension dial (red) 5. Lower looper thread tension dial (yellow) 6. Handle 7. Thread cutter 8. Presser foot ...

  • Pfaff Hobbylock 2.5 - page 5

    5 1 2 3 4 5 6 8 9 10 7 Accessories 1. Needle pack including three needles, size #14/90 and two needles, size #12/80. Two needles, size #14/90, are in the machine on delivery. 2. Screwdriver 3. Tweezers 4. Thread unreeling discs (4) 5. Lint brush 6. Knife blade (for the stationary lower cutter) 7. 2-thread converter 8. Thread spool nets (4) 9. Waste ...

  • Pfaff Hobbylock 2.5 - page 6

    6 A A Setting up the telescopic thread stand Pull out the spool stand in the direction of the arrow (A) Extend the telescopic thread stand to its full height, then turn until it clicks into place. Place the thread spools or cones over the cone holders on the spool pin. If the machine is already threaded, straighten the threads to prevent tangling. ...

  • Pfaff Hobbylock 2.5 - page 7

    7 A A Presser foot lift Raise the presser foot with the presser foot lift lever (A) at the back of the machine. Changing the needles Turn off the main power switch and unplug the machine. 1. Turn the hand wheel toward you until the needles are at the highest position. 2. Loosen, but do not remove the left (B) and/or right (A) needle clamp screw wit ...

  • Pfaff Hobbylock 2.5 - page 8

    8 A B C D A Disengage the movable upper cutter Place the movable upper cutter in nonworking position 1. Turn the hand wheel toward you until the upper cutter is raised to the highest position. 2. Open the front cover. 3. Push the movable cutter holder to the right as far as it will go. 4. Turn the knob away from you until the cutter clicks into the ...

  • Pfaff Hobbylock 2.5 - page 9

    9 2 3 4 1 Threading the machine A color coded diagram is located inside the front cover for quick reference. When threading the machine, thread only in the following order: 1. Upper looper threading - (Red) 2. Lower looper threading - (Yellow) 3. Right needle threading - (Green) 4. Left needle threading - (Blue) Important: If the lower looper shoul ...

  • Pfaff Hobbylock 2.5 - page 10

    10 1 3 2 4 5 6 7 8 8 Threading the upper looper (r ed) 1. Pass the thread from back to front through the thread guides on the thread stand (1). 2. Pull the thread from left to right under the thread guide at the back on the top cover (2). 3. Lift up the handle and bring the thread under it. While holding the thread with both hands, pass it between ...

  • Pfaff Hobbylock 2.5 - page 11

    11 1 3 2 4 5 6 7 8 10 9 10 9A 9B Threading the lower looper (yellow) 1. Pass the thread from back to front through the thread guide on the thread stand (1). 2. Pull the thread from left to right under the thread guide on the back of the top cover (2). 3. Lift up the handle and bring the thread under it. While holding the thread with both hands, pas ...

  • Pfaff Hobbylock 2.5 - page 12

    12 1 1 3 3 4 5 7 8 4 6 7 2 2 6 5 Threading the right needle (gr een) 1. Pass the thread from back to front through the thread guides on the thread stand (1). 2. Pull the thread from left to right under the thread guide on the back of the top cover (2). 3. Lift up the handle and bring the thread under it. While holding the thread with both hands, pa ...

  • Pfaff Hobbylock 2.5 - page 13

    13 Changing threads The following is an easy way to change threads: 1. Cut the thread in use near the spool, behind the guides on the telescopic thread stand. 2. Remove the thread spool and place the new thread on the spool pin. 3. Tie the end of the new thread to the end of the old thread. Cut the thread tails to 2-3 cm in length and À rmly pull ...

  • Pfaff Hobbylock 2.5 - page 14

    14 Thread tension settings Set the thread tension to suit the type of fabric and thread used. As the number on the thread tension discs increases, the thread tension becomes tighter. Lower looper thread and upper looper thread should be well balanced with the same tension (both looper threads should cross at the edge of the fabrics). Needle threads ...

  • Pfaff Hobbylock 2.5 - page 15

    15 Differential feed adjustment The differential feed system consists of two sets of feed teeth arranged one behind the other. Both feed teeth work independently of each other to give perfect results when sewing on speciality fabrics. When the amount of feed by the front feed teeth is changed in relation to the feed by the rear feed teeth it will ? ...

  • Pfaff Hobbylock 2.5 - page 16

    16 Presser foot pr essure adjustment The presser foot pressure is pre-set for sewing based on normal conditions. Adjustment might in some conditions be necessary. Increase or decrease the pressure until you are satis À ed with the result. Always test sew on a sample of your fabric before sewing on your garment. Less pressure: Decrease the pressure ...

  • Pfaff Hobbylock 2.5 - page 17

    17 Stitch À nger lever setting The stitch À nger lever should be set to “S” for all standard overlock sewing. To sew rolled edge you need to retract the stitch À nger by setting the stitch À nger lever to “R”. When moving the stitch À nger, be sure to push the lever as far as it will go in each direction. Rolled edge sewing The rolled ...

  • Pfaff Hobbylock 2.5 - page 18

    18 Flatlock sewing A Flatlock Stitch is made by adjusting the tension of the 2- or 3-thread overlock stitch, sewing the seam and pulling the fabric apart to Á atten the seam. The tensions must be adjusted correctly for the fabric to pull Á at. The Flatlock Stitch can be used both as a decorative construction stitch, sewing two pieces together (St ...

  • Pfaff Hobbylock 2.5 - page 19

    19 Corded overlock Corded overlock can be used to strengthen stitches when joining elastic fabrics such as knits. Cording prevents knit fabrics from stretching and also stabilize the seams. 1. Insert the cord through the hole in the front of the foot. 2. Position the cord under the foot to the back of the machine and sew the garment seam. 3. The co ...

  • Pfaff Hobbylock 2.5 - page 20

    20 Machine maintenance An overlock requires more frequent maintenance than a conventional machine for two reasons: - A lot of lint is produced when the cutters are cutting the the fabric. - An overlock runs at a very high speed and needs to be oiled frequently to lubricate the internal working parts. Cleaning Turn off the main power switch and unpl ...

  • Pfaff Hobbylock 2.5 - page 21

    21 1 2 3 Replacing the stationary cutter Turn off the main power switch and unplug the machine. The stationary cutter should be changed when it becomes dull. The stationary cutter can be replaced according to the following directions. If you are having any dif À culties, consult your dealer to make the necessary adjustments. 1. Open the front cove ...

  • Pfaff Hobbylock 2.5 - page 22

    22 T rouble shooting Problem Solution Page Fabric does not feed well - Lengthen stitch length. - Increase presser foot pressure for heavy weight fabric. - Decrease presser foot pressure for light weight fabric. - Check the differential feed. 16 16 16 15 Needle breaks - Insert needle correctly. - Do not pull fabric while sewing. - Tighten needle set ...

  • Pfaff Hobbylock 2.5 - page 23

    23 Combination Needle position Stitch length Stitch width Differ- ential feed Stitch À nger 2-thread con- verter Thread tension Stitch F abric BG R Y 2-thread overlock, wide Left 3 R(3.5) 1 S Yes 0.0 - - 5.0 0.5 - - 5.0 1.0 - - 5.0 0.0 - - 5.0 1.0 - - 5.0 1.5 1.0 - - 5.0 2-thread overlock, narrow Right 3 R(3.5) 1 S Yes - 0.0 - 4.0 - 0.5 - 5.0 - 1. ...

  • Pfaff Hobbylock 2.5 - page 24

    24 Combination Needle position Stitch length Stitch width Differ- ential feed Stitch À nger 2-thread con- verter Thread tension Stitch F abric BG R Y 2-thread overlock, wr ap, narrow Right 3 R(3.5) 1 S Yes - 3.5 - 2.0 - 4.0 - 2.0 - 5.0 - 2.0 - 3.0 - 2.0 - 4.0 - 2.0 1.5 - 5.0 - 2.0 2-thread rolled edge Right 1 3 1 R Yes - 3.0 - 2.0 - 3.0 - 2.0 Not ...

  • Pfaff Hobbylock 2.5 - page 25

    25 Combination Needle position Stitch length Stitch width Differ- ential feed Stitch À nger 2-thread con- verter Thread tension Stitch F abric BG R Y 3-thread overlock stitch, wide Left 3 R(3.5) 1 SN o 2.5 - 3.0 3.0 3.0 - 3.0 3.0 3.5 - 3.0 3.0 2.5 - 3.0 3.0 3.0 - 3.0 3.0 1.5 3.0 - 3.0 3.0 3-thread overlock stitch, narrow Right 3 R(3.5) 1 SN o - 2. ...

  • Pfaff Hobbylock 2.5 - page 26

    26 Combination Needle position Stitch length Stitch width Differ- ential feed Stitch À nger 2-thread con- verter Thread tension Stitch F abric BG R Y 3-thread rolled edge Right 1 3 1 R No - 2.0 5.0 7.0 - 2.0 5.0 8.0 Not recommended Right 1 3 1 R No - 3.0 4.0 6.0 Not recommended 3-thread narrow edge Right 1 3 1 R No - 3.0 5.0 3.0 - 3.0 5.0 4.0 Not ...

  • Pfaff Hobbylock 2.5 - page 27

    27 F abric / Needle / Thr ead table F abric Light fabric (voile, crepe, georgette, etc.) Medium fabric (cotton, chino, wool, satin etc.) Heavy fabric (denim, jersey, tweed etc.) Needle #12/80 #12/80, #14/90 #14/90 Thread Polyester (spun À lament) Twisted thread #60/2 - #80/2 (Twisted thread #80/3 - #100/3) Twisted thread #60/2 Twisted thread #50/2 ...

  • Pfaff Hobbylock 2.5 - page 28

    413 17 36 - 26E • English • Inhouse • © 2010 KSIN Luxembourg II, S.ar.l. • All rights reserved • Printed in Sweden on environment friendly paper www .pfaff.com ...

Manufacturer Pfaff Category Sewing Machine

Documents that we receive from a manufacturer of a Pfaff Hobbylock 2.5 can be divided into several groups. They are, among others:
- Pfaff technical drawings
- Hobbylock 2.5 manuals
- Pfaff product data sheets
- information booklets
- or energy labels Pfaff Hobbylock 2.5
All of them are important, but the most important information from the point of view of use of the device are in the user manual Pfaff Hobbylock 2.5.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Pfaff Hobbylock 2.5, service manual, brief instructions and user manuals Pfaff Hobbylock 2.5. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Pfaff Hobbylock 2.5.

Similar manuals

A complete manual for the device Pfaff Hobbylock 2.5, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Pfaff Hobbylock 2.5 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Pfaff Hobbylock 2.5.

A complete Pfaff manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Pfaff Hobbylock 2.5 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Pfaff Hobbylock 2.5, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Pfaff Hobbylock 2.5, that we can find in the current document
3. Tips how to use the basic functions of the device Pfaff Hobbylock 2.5 - which should help us in our first steps of using Pfaff Hobbylock 2.5
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Pfaff Hobbylock 2.5
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Pfaff Hobbylock 2.5 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Pfaff Hobbylock 2.5?

Use the form below

If you did not solve your problem by using a manual Pfaff Hobbylock 2.5, ask a question using the form below. If a user had a similar problem with Pfaff Hobbylock 2.5 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)