English dropdown-ico

Manual Euro-Pro 9110

79 pages 2.41 mb
Download

Go to site of 79

Summary
  • Euro-Pro 9110 - page 1

    Another quality product from Model 91 10 ...

  • Euro-Pro 9110 - page 2

    SYMBOL INSTRUCTIONS Raise needle Raise presser foot Lower presser foot ...

  • Euro-Pro 9110 - page 3

    IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic safety should always be followed, including the following: Read all instructions before using this sewing machine. -To reduce the risk of electric shock: 1. An appliance should never be left unattended when plugged in. 2. Always unplug this appliance from the electric outlet im ...

  • Euro-Pro 9110 - page 4

    CONTENTS PRINCIPAL PARTS OF THE MACHINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 BUTTONS OF THE MACHINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 LCD SCREEN . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Euro-Pro 9110 - page 5

    CONTENTS BLIND HEM/ LINGERIE STITCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 BUTTON SEWING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 BUTTONHOLE STITCHING . . . . . . . . . . . . ...

  • Euro-Pro 9110 - page 6

    3 5 4 PRINCIPAL PARTS OF THE MACHINE 1 Bobbin thread guide Tension dial Thread take-up lever Horizontal spool pin Hole for second spool pin Bobbin winder with on/off switch Face plate Presser foot pressure Buttonhole lever Auto needle threader Needle plate Sewing table and accessory box LCD screen Function buttons Speed limiting adjustment lever Ha ...

  • Euro-Pro 9110 - page 7

    2 BUTTONS OF THE MACHINE BUTTONS OF THE MACHINE 1. Start/stop button 2. Reverse button 3. Auto-lock button 4. Needle up/down position button Press this button to start or stop the machine. Hold down this button to sew either backwards or a reinforcement stitch at a low speed. Hold down this button to sew locking stitches immediately or at the end o ...

  • Euro-Pro 9110 - page 8

    7. Mode selection button 8. Elongation button 9. Mirror button 10. Twin needle button Press this button to select direct mode, utility and decorative pattern mode, block letter mode, script letter mode and outline letter mode. Pattern 30 to 39 can be elongated up to five times its normal length by pressing this button. Press this button to sew a re ...

  • Euro-Pro 9110 - page 9

    LCD SCREEN LCD SCREEN 4 Number of current unit Total number of unit Memory group Pattern for selecting Stitch width Stitch length Sound on/off Auto-lock Needle up/down position Mirror Stitch width Auto-stop Sound on/off Needle up/down position Auto-lock Reverse Pattern number Pattern Tension Needle position Stitch length Suggested presser foot and ...

  • Euro-Pro 9110 - page 10

    The portion marked in purple on the chart shows the one unit of each pattern. below 5 PATTERN CHART PATTERN CHART Outline style 01 02 03 04 05 06 07 08 09 10 11 1 2 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 V X Block style 01 02 03 04 05 06 07 08 09 10 11 1 2 13 ...

  • Euro-Pro 9110 - page 11

    6 ACCESSORIES ACCESSORIES 1. All purpose foot (T)- 2. Zipper foot (I)- 3. Buttonhole foot (D) - 4. Cording foot (M) - 5. Overcasting foot (E) - 6. Blind hem foot (F) - 7. Hemmer foot (K) - 8. Satin stitch foot (A) - 9. Quilting foot (P) - 10. Darning/ Embroidery foot - 11. Gathering foot - 12. Button sewing foot - 13. Brush/ Seam ripper - 14. Spool ...

  • Euro-Pro 9110 - page 12

    7 CONNECTING THE MACHINE TO THE POWER SOURCE CONNECTING THE MACHINE TO THE POWER SOURCE Connecting the machine Before connecting the power supply, make sure that the voltage and frequency shown on the machine is conforming with your electrical power. Place the machine on a stable table. 1. Connect the power line cord to the machine by inserting the ...

  • Euro-Pro 9110 - page 13

    8 STARTING SEWING STARTING SEWING Start/stop button With the sewing machine turned off, insert the foot control plug into its connector on the sewing machine. Turn on the sewing machine, and then slowly depress the foot control to start sewing. Release the foot control to stop the sewing machine. Foot control The machine will start running when Sta ...

  • Euro-Pro 9110 - page 14

    9 CHANGING THE PRESSER FOOT CHANGING THE PRESSER FOOT (1) Raise the presser foot bar (a). Attach the presser foot holder (b) as illustrated. (2) Lower the presser foot holder (b) until the cut-out (c) is directly above the pin (d). Raise the lever (e). Lower the presser foot holder (b) and the presser foot (f) will engage automatically. (3) Raise t ...

  • Euro-Pro 9110 - page 15

    MATCHING NEEDLE/ FABRIC/ THREAD MATCHING NEEDLE/ FABRIC/ THREAD NEEDLE, FABRIC, THREAD SELECTION GUIDE 10 Please Note: - In general, fine threads and needles are used for sewing fine fabrics, and thicker t hreads are used for sewing heavy fabrics. - Always test thread and needle size on a small piece of fabric which will be used for actual sewing. ...

  • Euro-Pro 9110 - page 16

    All purpose foot (T) Zipper foot (I) Buttonhole foot (D) Cording foot (M) Overcasting foot (E) Blind hem foot (F) Hemmer foot (K) Satin stitch foot (A) Quilting foot (P) Darning/ Embroidery foot Gathering foot Button sewing foot Walking foot APPLICATION PRESSER FOOT General sewing, Patchwork stitches, Decorative stitching, Smocking, Fagoting, etc. ...

  • Euro-Pro 9110 - page 17

    1. Place the thread and spool holder onto the spool pin. For smaller spools of thread, place spool holder with the small side next to the spool or use the small spool holder. 2. Snap the thread into the thread guide (Child beneath thread guide cover). 3. Wind the thread clockwise around the bobbin winder tension discs. 4. Place the thread end throu ...

  • Euro-Pro 9110 - page 18

    WINDING THE BOBBIN WINDING THE BOBBIN 13 6. will display the animation of bobbin winding, press the engaging lever to right, the animation disappear, LCD display the frame of ordinary operating. When the bobbin winder switch is pressed to the left, LCD 7. Hold the thread tail securely in one hand. 8. Press the Start/stop button or foot control. 9. ...

  • Euro-Pro 9110 - page 19

    Attention: Turn power switch to off ("O") before inserting or removing the bobbin. When inserting or removing the bobbin, the needle must be fully raised. 1. Insert the bobbin in the bobbin case with the thread running in a counterclockwise direction (arrow). 2. Pull the thread through the slit (A). 3. Pull the thread toward the left and ...

  • Euro-Pro 9110 - page 20

    THREADING THE UPPER THREAD THREADING THE UPPER THREAD Please Note: It is important to carry out the threading correctly as by not doing so several sewing problems could result. Start by raising the needle to its highest point, and also raise the presser foot to release the tension discs. 1. Lift up the spool pin. Place the spool of thread on the sp ...

  • Euro-Pro 9110 - page 21

    THREADING THE UPPER THREAD THREADING THE UPPER THREAD 16 5. Then, down and around the check spring holder. 6. At the top of this movement, pass the thread from right to the left through the slotted eye of the take-up lever and then downwards again. 7. Pass the thread behind the flat, horizontal thread guide. 4. Thread the tension module by passing ...

  • Euro-Pro 9110 - page 22

    USING THE NEEDLE THREADER USING THE NEEDLE THREADER 2. The needle threader automatically turns to the threading position and the hook pin passes through the needle eye. 3. Take the thread in front of the needle. 4. Hold the thread loosely and release the lever slowly. The hook will turn and pass the thread through the needle eye forming a loop. Pul ...

  • Euro-Pro 9110 - page 23

    Upper thread Bobbin thread THREAD TENSION THREAD TENSION - Basic thread tension setting: "4" - To increase the tension, turn the dial to the next number up. To reduce the tension, turn the dial to the next number down. - Proper setting of tension is important to good sewing. - There is no single tension setting appropriate for all the sti ...

  • Euro-Pro 9110 - page 24

    1. Hold the upper thread with the left hand. Turn the handwheel towards you (counterclockwise) lowering, then raising the needle. 2. Gently pull on the upper thread to bring the bobbin thread up through the needle plate hole. The bobbin thread will come up in a loop. 3. Pull both threads to the back under the presser foot. 1 2 Raise the presser foo ...

  • Euro-Pro 9110 - page 25

    TWO-STEP PRESSER FOOT LIFTER TWO-STEP PRESSER FOOT LIFTER 1. The presser foot lifter raises and lowers your presser foot. 2. When sewing several layers or thick fabrics, the presser foot can be raised a second stage for easy positioning of the work. With the sewing table off the machine, the feed dog adjustment lever can be seen on the base in back ...

  • Euro-Pro 9110 - page 26

    21 Needle up/down position button Auto-lock button Reverse button Start/stop button OPERATION BUTTONS OPERATION BUTTONS The machine will start running when start/stop button is pressed and will stop when pressed the second time. The machine will rotate slowly at the beginning of the sewing. The sewing speed can be controlled by the speed limiting a ...

  • Euro-Pro 9110 - page 27

    OPERATION BUTTONS OPERATION BUTTONS When the patterns 00-06 are selected, the machine will immediately sew 3 locking stitches when the Auto-lock button is pressed, then automatically stop. The LCD will display the figure " " until the machine is stopped. Auto-lock button When the patterns 07-15, 30-99 are selected, press the Auto-lock but ...

  • Euro-Pro 9110 - page 28

    FUNCTION BUTTONS FUNCTION BUTTONS Stitch width adjustment button When you select a stitch, the machine will automatically set the recommended stitch width, which will be indicated by numbers on the LCD screen. The stitch width can be regulated by pressing the stitch width adjustment buttons. Certain stitches have a limited stitch width. Mode select ...

  • Euro-Pro 9110 - page 29

    24 FUNCTION BUTTONS FUNCTION BUTTONS Stitch length adjustment button When you select a stitch the machine will automatically set the recommended stitch length which will be indicated by numbers on the LCD screen. The stitch length can be adjusted by pressing the stitch length adjustment buttons. To shorten the stitch length, press the " " ...

  • Euro-Pro 9110 - page 30

    25 FUNCTION BUTTONS FUNCTION BUTTONS Mirror button (see page 57) The patterns 00-15, 30-99 can be mirror imaged along a vertical axis by pressing the " " button, LED light will turn on. The machine will continue to sew the reflected pattern until the mirror button is pressed again. The mirror function also will be canceled if the pattern ...

  • Euro-Pro 9110 - page 31

    SELECTION BUTTONS SELECTION BUTTONS Direct pattern selection and number buttons Clear button Edit button Memory button Direct pattern selection and number buttons Direct pattern selection Press the buttons to select the utility patterns shown beside the number button when the mode button is set at the Direct mode. Number buttons Press the number bu ...

  • Euro-Pro 9110 - page 32

    SELECTION BUTTONS SELECTION BUTTONS Press this button when the incorrect character is selected. Each press of this button erases one character, or press this button to remove an added pattern when sewing combinations of characters or decorative stitches. Clear button 1 23 4 7 5 8 6 9 0 If you wish to modify any settings in the memory mode, use the ...

  • Euro-Pro 9110 - page 33

    USEFUL SKILLS USEFUL SKILLS 1. Stop the sewing machine when you reach a corner. 2. Lower the needle into the fabric manually or by pressing the needle up/down button once. 3. Raise the presser foot. 4. Use the needle as a pivot and turn the fabric. 5. Lower the presser foot and resume sewing. Reverse stitching is used to secure the threads at the b ...

  • Euro-Pro 9110 - page 34

    The black button on the right side of the presser foot will lock the presser foot in a horizontal position if you push it in before lowering the presser foot. This ensures even feeding at the beginning of a seam and helps when sewing multiple layers of fabric such as sewing over seams when hemming jeans. When you reach the point of an increased thi ...

  • Euro-Pro 9110 - page 35

    Changing the needle position These setting apply only to pattern 00-04. The pre-set position is "3.5", center position. When you press the " " stitch width adjustment button, the needle position will move to the left. When you press the "+" stitch width adjustment button, the needle position will move to the right. On ...

  • Euro-Pro 9110 - page 36

    It assures you of a stitch that is strong and flexible and will give with the fabric without breaking. Good for easy to ravel and knit fabrics. It is good for joining durable fabric such as denims. These stitches can also be used as a decorative top stitch. Triple zigzag stretch stitch is suitable for firm fabrics like denim, poplin, duck, etc. T S ...

  • Euro-Pro 9110 - page 37

    Using the overcasting foot 1. Change the presser foot to the overcasting foot. 2. Sew the fabric with the fabric edge against the guide of the overcasting foot. Attention: The overcasting foot should be used to sew with patterns 05 and 08 only and do not set the stitch width narrower than "5.0". It is possible that needle could hit the pr ...

  • Euro-Pro 9110 - page 38

    1. Fold the fabric as illustrated with the wrong side uppermost. 2. Place the fabric under the foot. Turn the handwheel forwards by hand until the needle swings fully to the left. It should just pierce the fold of the fabric. If it does not, adjust the stitch width accordingly. 3. Adjust the guide (b) by turning the knob (a) so that the guide just ...

  • Euro-Pro 9110 - page 39

    Change the presser foot to the button sewing foot. 2. Position the work under the foot. Place the button in the desired position, lower the foot. 3. Select zig zag pattern. Adjust the stitch width to "2.0-7.0" according to the distance between the two holes of the button. 4. Turn the handwheel to check that the needle goes cleanly into th ...

  • Euro-Pro 9110 - page 40

    Please Note: Before sewing a buttonhole on your project, practice on a scrap piece of the same type of fabric. 35 16: 17: 18: 19: 20: 21: 22: 23: 24: 25: 26: For thin or medium fabric For horizontal holes on blouses or shirts made from thin or medium fabric For thin or medium fabric For horizontal holes on blouses or shirts made from thin or medium ...

  • Euro-Pro 9110 - page 41

    3. Select the buttonhole stitch. Adjust the stitch width and the stitch length to the desired width and density. 4. Position the fabric under the presser foot so that the centerline's mark is aligning with the center of the buttonhole foot. Lower the buttonhole lever, then push it to the back. Please Note: When you select any buttonhole patter ...

  • Euro-Pro 9110 - page 42

    6. Buttonholes are sewn from the front of the presser foot to the back, as shown. 37 BUTTONHOLE STITCHING BUTTONHOLE STITCHING 6 7. Raise the presser foot and cut thread. To sew over same buttonhole, raise the presser foot (will return to original position). After sewing the buttonhole stitch, raise the buttonhole lever until it stops. 7 PUSH Pleas ...

  • Euro-Pro 9110 - page 43

    38 BUTTONHOLE STITCHING BUTTONHOLE STITCHING 8. Cut the center of the buttonhole being careful not to cut any stitches on either side. Use a pin as a stopper at the bartack so you do not cut too much. 8 When sewing buttonholes on stretch fabric, hook heavy thread or cord under the buttonhole foot. 1. Attach the buttonhole foot and hook the gimp thr ...

  • Euro-Pro 9110 - page 44

    39 ADJUSTING PATTERN BALANCE ADJUSTING PATTERN BALANCE If the decorative stitch patterns, numbers or manual buttonhole stitch are uneven when you sew on a particular fabric, adjust them with the feed balancing dial. The dial should usually be in a neutral position. A BC A BC A BC Adjusting distorted stretch stitch patterns A. When Patterns are too ...

  • Euro-Pro 9110 - page 45

    40 EYELET STITCH EYELET STITCH 1. Select pattern 27 to get the eyelet stitch. Attach presser foot "A". 2. Press the " " or "+" stitch width adjustment to button select the eyelet size. Size of eyelet. A. Large: 7.0mm (1/4 inch). B. Medium: 6.0mm (15/64 inch). C. Small: 5.0mm (3/16 inch). 3. Lower the needle into the fa ...

  • Euro-Pro 9110 - page 46

    41 1. Select pattern 28 or 29 from the Group Patterns "A" to get the darning stitch. Change the presser foot to the buttonhole foot. 3. Pull the button holder to the rear. Set the button guide plate on buttonhole foot to the desired length. 1 2. Baste the upper fabric and the under fabric together. Select the needle position. Lower the pr ...

  • Euro-Pro 9110 - page 47

    5. Position the fabric so that the needle is 2mm (1/16 inch) in front of the area to be darned, and then lower the presser foot lever. When lowering the presser foot, do not push in the front of the presser foot, otherwise the darning will not be sewn with the correct size. Please Note: 6. Pass the upper thread down through the hole in the presser ...

  • Euro-Pro 9110 - page 48

    43 1. Baste the zipper opening on the garment. 2. Press open the seam allowance. Place the zipper face down on the seam allowance with the teeth against the seam line. Baste the zipper tape. 3. Attach the zipper foot. Attach the right side of the presser foot pin to the holder when sewing the left side of the zipper. 4. Attach the left side of the ...

  • Euro-Pro 9110 - page 49

    Inserting a side zipper 44 1. Baste the zipper opening on the garment. 2. Fold back to the left seam allowance. Turn under the right seam allowance to form 3mm (1/8 inch) fold. 3. Attach the zipper foot. Attach the right side of the presser foot pin to the holder when sewing the left side of the zipper. Attach the left side of the presser foot pin ...

  • Euro-Pro 9110 - page 50

    45 K 1. Fold edge of fabric over about 3mm (1/8 inch), then fold it over again 3mm (1/8 inch) for about 5cm (2 inches) along the edge of the fabric. 2. Insert the needle into the fold by rotating the handwheel toward you, and lower the presser foot. Sew several stitches and raise the presser foot. Insert the fabric fold into the spiral opening of h ...

  • Euro-Pro 9110 - page 51

    46 M Mark the design on the fabric. Insert the cord in the center groove of the cording foot from the right side opening. Pull the cord about 5cm (2 inches) behind the foot. The grooves under the foot will hold the length of the cord in place while the stitches are being form over the cord. Select the stitch and adjust the stitch width so that the ...

  • Euro-Pro 9110 - page 52

    47 A Use the satin stitch foot for satin stitching and sewing decorative stitches. This foot has a full indentation on the underside to allowed easy sewing over the thickness of the stitches form by closely spaced zigzag stitches, and even feeding of the fabric. To tailor the satin or decorative stitch pattern, you may adjust the length and width o ...

  • Euro-Pro 9110 - page 53

    48 P Insert the quilting guide in the presser foot holder as illustrated and set the space as you desire. Sew the first row and move over the fabric to sew successive rows with the guide riding along the previous row of stitching. QUILTING QUIL TING 3.5 1.0~3.0 ...

  • Euro-Pro 9110 - page 54

    49 1. Remove the presser foot holder and attach the gathering foot. 2. Sew a single row or multiple rows of straight stitches. 3. If more gathering is required, loosen the upper thread tension to below 2 so that the bobbin thread lies on the underside of the material. 4. Pull the bobbin threads to obtain the desired amount of gather, then tie the t ...

  • Euro-Pro 9110 - page 55

    50 1. Use the gathering foot to sew straight lines 1cm (3/8 inch) apart, across the area to be smocked. * For gathering sewing instructions, see page 49. 2. Knot the threads along one edge. Pull the bobbin threads and distribute the gathers evenly. Secure the threads at the other end. 3. Reduce the tension, if necessary and sew decorative pattern s ...

  • Euro-Pro 9110 - page 56

    51 Remove the presser foot holder, and attach the darning foot to the presser foot holder bar. The lever (a) should be behind the needle clamp screw (b). Press the darning foot on firmly from behind with your index finger and tighten the screw (c). Move the drop feed control to " " to lower the feed dogs. First sew around the edges of the ...

  • Euro-Pro 9110 - page 57

    Select zigzag stitch pattern and adjust the stitch width as desired. Stitch along the outline of the design by moving the embroidery hoop. Make sure to maintain a constant speed. Fill in the design working from the outline towards the inside. Keep the stitches close together. You will get longer stitches by moving the hoop faster and shorter stitch ...

  • Euro-Pro 9110 - page 58

    It is easier to guide the fabric and you have a better view of the seam when using the standard, regular foot on your machine. Your sewing machine offers excellent stitch quality on a wide range of fabrics from delicate chiffons to multiple layers of denim. 53 WALKING FOOT WALKING FOOT 1 2 a b c 3 4 Please Note: Always try to sew first without the ...

  • Euro-Pro 9110 - page 59

    1. Place the two pieces of fabric with the right side together and sew with the straight stitch. 2. Open the seam allowances and presses it flat. 3. Place the center of the presser foot on the seam line of the joined pieces of fabric and sew over the seam. T 1. Separate the folded edges of the fabric pieces with a gap of 4mm (1/8 inch) and baste th ...

  • Euro-Pro 9110 - page 60

    55 T T A 1. Fold the fabric right side together in and sew along the edge. 2. Cut the fabric along the seam leaving an allowance of 3mm (1/8 inch) for seaming. Notch the allowance. 3. Turn fabric over and push out the curved seam to the surface and iron it. 1. Sew on hem line. 2. Trim the fabric close to the stitching taking care not to cut the thr ...

  • Euro-Pro 9110 - page 61

    1. The stitch can be elongated up to five times its normal length by pressing the elongation button. ELONGATION ELONGATION 1 A 2.5~7.0 0.3~1.0 3 x5 x4 x3 x2 x1 2 2. The LCD screen icon for elongation imaging of the pattern appears. 3. When the width or length or stitch is changed, a greater variety of patterns are available. Please Note: The patter ...

  • Euro-Pro 9110 - page 62

    MIRROR MIRROR 57 1. Select the pattern. 1 3 2 3. The LCD screen icon for mirror imaging of the pattern appears. 2. Pressing the mirror button. Please Note: - Pattern 16-29 cannot be mirror imaged. - Mirror imaged patterns can also be combined with other patterns. 4 A. Normal pattern sewing. B. Mirror pattern sewing. A B ...

  • Euro-Pro 9110 - page 63

    58 1. Insert the twin needle. T 2. Follow the instructions for single-needle threading using the horizontal spool pin. Thread through the left needle. Set the second spool pin (included with the accessories) into the hole on the top of the machine. Thread through remaining points, making certain to omit the thread guide above the needle and pass th ...

  • Euro-Pro 9110 - page 64

    MEMORY MEMORY 59 Please Note: - Multiple patterns selecting from pattern modes , , , can be combined and sewn together. - - - This machine has 4 modules of program memory and each module can retain 20 units of stitches. Patterns 16-29 cannot be entered into memory. All the units in the memory can be edited to set its function such as Stitch length, ...

  • Euro-Pro 9110 - page 65

    MEMORY MEMORY 60 6 7 6. The selected pattern displays on the LCD screen and the cursor move to the next position. 7. Repeat step 5, 6 for more patterns to be stored in the memory. Please Note: When the memory the full with 20 units of patterns, the machine will beep to signal it. 5. Press the desired pattern number. (E.g.68) 5 8 8. Press the " ...

  • Euro-Pro 9110 - page 66

    MEMORY MEMORY 61 Editing patterns 1. Use the stitch width adjustment button to select the pattern that you wish to edit while in the memory mode. 2. Press the " " button to edit the pattern. The stitch length, stitch width, Elongation, Mirror, and Auto-lock of the patterns can be adjusted manually. 4. Press the " " button when c ...

  • Euro-Pro 9110 - page 67

    MEMORY MEMORY 62 5. The cursor on the LCD screen will move along with the sequential pattern while sewing. 6. Press the " " button to leave memory mode and return to the normal screen. 1. Press the " " button to enter memory mode and then input the number of memory module when the cursor start flashing. 2. Input the number of me ...

  • Euro-Pro 9110 - page 68

    WARNING FUNCTIONS WARNING FUNCTIONS 63 Warning animation message display Presser foot is not lowered The Start/stop button or reverse button was pressed while the presser foot was raise. BH lever is not lowered The buttonhole or darning stitch was selected and the start/stop button was pressed while the buttonhole lever is raised. BH lever is not l ...

  • Euro-Pro 9110 - page 69

    WARNING FUNCTIONS WARNING FUNCTIONS 64 - When operating correctly: 1 beep - When the memory is full 20 units of pattern: 2-short beeps - When operating incorrectly: 3-short beeps - When the sewing machine is in trouble and can't sew: 8 seconds short beeps It means that the thread is twisted or jammed and the hand wheel axle can't move. Pl ...

  • Euro-Pro 9110 - page 70

    BUZZER SOUND BUZZER SOUND 3. Pressing the " " button. The Buzzer sound setting mark will appear on the LCD screen when you have set it. 1 1. Press on the " " button and turn on the power switch. 2. You can select the mode by pressing the stitch width "+" or " " button. Select desired mode sound on " &quo ...

  • Euro-Pro 9110 - page 71

    66 Attention: Turn the power switch off and wait until the lamp has cooled down before touching it. 1. Loosen the screw (a) on the left side of the sewing head and remove the face plate (b). 2. If the machine is equipped with a 5W lamp, replace the bulb as follows: Pull light bulb downward to remove. Replace the bulb with same type rated 5W. Replac ...

  • Euro-Pro 9110 - page 72

    67 Attention: Disconnect the power cord from the wall socket before cleaning the screen and sewing machine surface, otherwise injury or electrical shock may result. If the front panel is dirty, wipe it gently with a soft, dry cloth. Do not use any organic solvents or detergents. If the surface of the sewing machine is dirty, lightly soak a cloth in ...

  • Euro-Pro 9110 - page 73

    68 MAINTENANCE MAINTENANCE 3. Remove the needle, presser foot and presser foot holder. R emove the bobbin cover plate and bobbin. Remove the screw holding the needle plate and remove the needle plate. 4. Lift up the bobbin case and remove it. 5. Clean the hook race, feed dog and bobbin case with a brush. Also clean them, using a soft, dry cloth. 6. ...

  • Euro-Pro 9110 - page 74

    69 Before calling for service, check the following items. If the problem still persists, contact the place of purchase or your nearest authorized dealer. TROUBLE SHOOTING GUIDE TROUBLE SHOOTING GUIDE Problem Cause Correction Upper thread breaks Lower thread breaks Skipped stitches Needle breaks Loose stitches Seam gather or pucker 1.The machine is ...

  • Euro-Pro 9110 - page 75

    70 TROUBLE SHOOTING GUIDE TROUBLE SHOOTING GUIDE Seam puckering Patterns are distorted 1.The needle thread tension is too tight. 2.The needle thread is not threaded correctly. 3.The needle is too heavy for the fabric being sewn. 4.The stitch length is too long for the fabric. 5.The presser foot pressure is not correctly adjusted. 1.The correct pres ...

  • Euro-Pro 9110 - page 76

    QUICK ADJUSTMENT REFERENCE CHART QUICK ADJUSTMENT REFERENCE CHART : Adjustments can be made. 71 00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 3.5 0.0 3.5 3.5 3.5 5.0 5.0 5.0 5.0 5.0 3.5 3.5 3.5 5.0 7.0 6.0 5.0 5.5 5.0 6.0 5.0 5.0 7.0 7.0 7.0 6.0 6.0 7.0 7.0 7.0 7.0 7.0 7.0 7. ...

  • Euro-Pro 9110 - page 77

    QUICK ADJUSTMENT REFERENCE CHART QUICK ADJUSTMENT REFERENCE CHART : Adjustments can be made. 72 Functions Presser Foot Stitch Pattern Auto Manual Auto Manual Auto-lock Elongation Mirror/ Presser foot Twin needle Reverse Width (mm) Length (mm) Memory /A /A /A /A /A /A /A /A /A /A 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 6 ...

  • Euro-Pro 9110 - page 78

    QUICK ADJUSTMENT REFERENCE CHART QUICK ADJUSTMENT REFERENCE CHART Functions Presser Foot Stitch Pattern Auto Manual Auto Manual Auto-lock Elongation Mirror/ Presser foot Twin needle Reverse Width (mm) Length (mm) Memory /A /A /A /A /A /A /A /A /A /A /A /A /A /A /A /A /A /A /A /A 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 7.0 7.0 7. ...

  • Euro-Pro 9110 - page 79

    021D3B0101 EURO-PRO 91 10(9000B) (C)( ) Aug/05 ...

Manufacturer Euro-Pro Category Sewing Machine

Documents that we receive from a manufacturer of a Euro-Pro 9110 can be divided into several groups. They are, among others:
- Euro-Pro technical drawings
- 9110 manuals
- Euro-Pro product data sheets
- information booklets
- or energy labels Euro-Pro 9110
All of them are important, but the most important information from the point of view of use of the device are in the user manual Euro-Pro 9110.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Euro-Pro 9110, service manual, brief instructions and user manuals Euro-Pro 9110. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Euro-Pro 9110.

Similar manuals

A complete manual for the device Euro-Pro 9110, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Euro-Pro 9110 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Euro-Pro 9110.

A complete Euro-Pro manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Euro-Pro 9110 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Euro-Pro 9110, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Euro-Pro 9110, that we can find in the current document
3. Tips how to use the basic functions of the device Euro-Pro 9110 - which should help us in our first steps of using Euro-Pro 9110
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Euro-Pro 9110
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Euro-Pro 9110 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Euro-Pro 9110?

Use the form below

If you did not solve your problem by using a manual Euro-Pro 9110, ask a question using the form below. If a user had a similar problem with Euro-Pro 9110 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)