English dropdown-ico

Manual TRENDnet trend COMBI 650

16 pages 0.22 mb
Download

Go to site of 16

Summary
  • TRENDnet trend COMBI 650 - page 1

    ...

  • TRENDnet trend COMBI 650 - page 2

    Combi 65 0 -2- ITEMS ENCLOSED Length = 760mm Width = 360mm Thickness = 13mm Weight = 4.2kg Specification 1 x Solid laminate template 2 x Location bushes 1 x Manual 1 x Guarantee card 1 x Length setting stop 1 x Machine screw csk 1 x Washer 1 x Knob ...

  • TRENDnet trend COMBI 650 - page 3

    Combi 65 0 -3- SAFET Y PR ECAUT I ON S ■ Alwa ys switch off the po wer and unplug the router when changing cutters or when making adjustments. ■ Alwa ys wear protectiv e goggles when routing. ■ Wear sound protectiv e ear muffs when routing for long periods of time . ■ Alwa ys wear a dust mask or respirator . Use dust e xtraction equipment w ...

  • TRENDnet trend COMBI 650 - page 4

    Combi 65 0 -4- Recommended Cutters A 12.7mm ( 1 / 2 ”) diameter cutter must be used, which has a 50mm cutting reach and plunge cut facility . Router must be plunged in stages of maxim um 8mm in one pass. Description Order Ref. Craft Range Cutter C153x1/2TC As above with TC centre tip C153Dx1/2TC T rade Range Cutter TR17x1/2TC As above with TC cen ...

  • TRENDnet trend COMBI 650 - page 5

    Combi 65 0 -5- Gener al instructions f or fitting sub-bases to Router 1. Fit line-up guide bush onto sub-base , with screws supplied. 2. Fit 12.7mm ( 1 / 2 ”) shank line-up pin into collet of router . Plunge router until pin projects through base and lock plunge . 3. Locate guide bush and sub-base assemb ly ov er protruding pin. 4. Line up fixing ...

  • TRENDnet trend COMBI 650 - page 6

    Combi 65 0 -6- 100mm (4”) min. throat depth Panel Butt Connectors P anel butt connectors are essential f or connecting worktops. The y fit into the recess on the underside of the worktop and are tightened with a 10mm spanner . The jig has integral bolt recess slots to allow the bolt recess to be cut in the underside of the worktop , using the cut ...

  • TRENDnet trend COMBI 650 - page 7

    Combi 65 0 -7- Carry Case Hard wearing carry case to protect and allow ease of carrying of the COMBI650 Jig. Description Order Ref. Carry Case for COMBI650 CASE/650 Fill and Seal A solvent and silicone free coloured bonding sealant used to seal worktop joints to pre vent moisture reaching the core material. A vailab le in nine colours, Fill and Sea ...

  • TRENDnet trend COMBI 650 - page 8

    Combi 65 0 -8- AS S EM B L Y Loc ation Bush Identification T wo location bushes are used in diff erent holes in the jig to align the correct template aperture for the application. The holes are colour coded f or easy identification with dots as f ollows: Green dot – Female Joint Red dot – Male Joint Y ellow dot – Connector Recess The jig has ...

  • TRENDnet trend COMBI 650 - page 9

    Combi 65 0 -9- L ength Stop Arr angement OPERA TION Setting the Length Stop f or the Female Joint Carry out the setting operation first: ■ Fit bushes into Red dot location holes and offer the jig to the w orktop as shown. The Green dot location holes will be uppermost. ■ P osition the jig across the width of the worktop. Loosely fit the length ...

  • TRENDnet trend COMBI 650 - page 10

    Combi 65 0 -10- Male Joint Depending on accessibility la y female w orktop into position on units. La y male worktop on top and suppor t other end. Using a pencil dra w round the f emale cut onto the male. If inaccessible la y female onto male. Depending on a right or left hand joint, the pencil line ma y need to be transf erred on to the other sid ...

  • TRENDnet trend COMBI 650 - page 11

    Combi 65 0 -11- ■ Inser t both location b ushes into Red dot holes. Red dot f ace uppermost. ■ Lay jig across the w orktop, ensure the location bushes touch the postf or m edge. Clamp jig in position with quick action clamps . Draw a line 8.5mm a way from the jig slot edge. ■ With the mitred end of the length stop f acing towards the bac k of ...

  • TRENDnet trend COMBI 650 - page 12

    Combi 65 0 -12- Cutting the Bolt Recesses When the joint has been tested, proceed as follo ws to cut the recess f or panel butt connectors on the underside of the worktop . The same cutter and guide bush are retained and used with the integral bolt recess slots in the jig to produce the recesses f or the panel butt connectors. The bolt recess posit ...

  • TRENDnet trend COMBI 650 - page 13

    Combi 65 0 -13- Str engthening the Joint If the joint between the worktops is not suppor ted under neath, after some time the joint may ‘sag’ and become misaligned; to reduce this the joint should be reinf orced with a loose tongue or biscuit dowels . The biscuit jointing cutter set T rend Ref. 342 can be used with a por table router . The size ...

  • TRENDnet trend COMBI 650 - page 14

    Combi 65 0 -14- CO M B I 650 S P AR E P ART S D IAG RAM 1 2 7 3 8 5 4 6 CO M B I 65 0 - S P AR E P ART S LI ST v1.0 10/199 9 Item Qty Description Ref. 1 1 Combi 650 Jig COMBI/650 2 2 Alloy Bush BUSH/650 3 1 Length Setting Stop CJ/LSK 4 0 Machine Screw Csk M8 x 50mm Slot WP-SCW/41 5 0 W asher 8.5mm x 32mm x 1.0mm WP-W ASH/17 6 0 Knob M8 WP-KNOB/10 7 ...

  • TRENDnet trend COMBI 650 - page 15

    Combi 65 0 -15- Fault Cause Remedy ■ Joint does not fit correctly Cutter or guide b ush is the Check concentricity of cutter at the radius. incorrect diameter or location with guide bush. Cutter 12.7mm bushes are not against diameter with 30mm diameter worktop edge. guide bush. Ensure location bushes touch worktop . ■ The back edge of the joint ...

  • TRENDnet trend COMBI 650 - page 16

    MANU/650 v6.0 T rend Machinery & Cutting T ools Ltd. Odhams T rading Estate St Albans Road W atford WD24 7TR England Enquiries: _____________ 0800 487363 T echnical Support: _____ 01923 224681 Fax: _________________01923 236879 Email: ______ mailserver@trendm.co .uk WWW: _____ www .trendmachiner y .co .uk © Copyright T rend 2002. No par t of t ...

Manufacturer TRENDnet Category Router

Documents that we receive from a manufacturer of a TRENDnet trend COMBI 650 can be divided into several groups. They are, among others:
- TRENDnet technical drawings
- trend COMBI 650 manuals
- TRENDnet product data sheets
- information booklets
- or energy labels TRENDnet trend COMBI 650
All of them are important, but the most important information from the point of view of use of the device are in the user manual TRENDnet trend COMBI 650.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals TRENDnet trend COMBI 650, service manual, brief instructions and user manuals TRENDnet trend COMBI 650. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product TRENDnet trend COMBI 650.

Similar manuals

A complete manual for the device TRENDnet trend COMBI 650, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use TRENDnet trend COMBI 650 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of TRENDnet trend COMBI 650.

A complete TRENDnet manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual TRENDnet trend COMBI 650 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the TRENDnet trend COMBI 650, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the TRENDnet trend COMBI 650, that we can find in the current document
3. Tips how to use the basic functions of the device TRENDnet trend COMBI 650 - which should help us in our first steps of using TRENDnet trend COMBI 650
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with TRENDnet trend COMBI 650
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of TRENDnet trend COMBI 650 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning TRENDnet trend COMBI 650?

Use the form below

If you did not solve your problem by using a manual TRENDnet trend COMBI 650, ask a question using the form below. If a user had a similar problem with TRENDnet trend COMBI 650 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)