English dropdown-ico

Manual EAW Loudspeaker's

40 pages 0.39 mb
Download

Go to site of 40

Summary
  • EAW Loudspeaker's - page 1

    EA W L OUDSPEAKER OWNER ’ S MANU AL NEVERENDING INNOV A TION ...

  • EAW Loudspeaker's - page 2

    L oudspeak er O wner ’ s Manual Congratulations on the purchase of your new EAW loudspeaker. You now own one of the finest professional audio products available - the result of exceptional engineering and meticulous craftsmanship. This manual is intended for use with all EAW loudspeakers. As such, it contains information that is common to differe ...

  • EAW Loudspeaker's - page 3

    8. Do not install near any heat sources such as radiators , heat registers, sto ves, or other apparatus (including amplifiers) that produce heat. 9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other . A grounding type plug has two blades and a third grounding pron ...

  • EAW Loudspeaker's - page 4

    En cas de conflit d'informations, les informations fournies dans les brochures ou manuels accompagnant le produit annulent et remplacent celles de ce manuel. 1. CONSIGNES DE S É CURIT É - À LIRE EN PREMIER Lisez et respectez toutes les consignes de s é curit é de ce manuel av at d'utiliser le produit. Le non-respect de ces consignes ...

  • EAW Loudspeaker's - page 5

    19. Si l'enceinte est expos é e à des variations de temp é rature et d'humidit é , il se peut qu'un condensation interne se produise . La mise sous tension de l'appareil en pr é sence de cette condensation peut entra î ner une panne é lectrique . Si l'appareil est expos é à de telles variations , attendez au moins ...

  • EAW Loudspeaker's - page 6

    9. Non annullare la sicurezza garantita dall'utilizz di spine polarizzate o con messa a terra. Le spine polarizzate sono caratterizzate dalla presenza di due lamine , una pi ù grande dell'altra. Le spine con messa a terra sono caratterizzate dalla presenza di due lamine e di un "dente" per la messa a terra. a lamina maggiore e ...

  • EAW Loudspeaker's - page 7

    En caso de cualquier conflicto o duplicaci ó n, la informaci ó n que se adjunte en el manual que acompa ñ e a este documento sustituye a la informaci ó n contenida en estas p á ginas . 1. PRECAUCIONES DE SEURID AD - LEA ESTO PRIMER O Lea y respete todas las instrucciones de seguridad y aviso que aparezcan en este manual antes de comenzar a usa ...

  • EAW Loudspeaker's - page 8

    una salida de corriente que disponga de una conexi ó n a tierra de protecci ó n (la ercera l á mina que indicamos antes). 18. Este aparato no sobrepasa los l í mites de la clase A/clase AB (cualquiera que sea la aplicable) en cuanto a emisi ó n de ruidos de radio de aparatos digitales, de acuerdo a lo que viene estipulado en las leyes sobre in ...

  • EAW Loudspeaker's - page 9

    1. Lesen Sie diese Anleitung. 2. Bewahren Sie diese Anleitung auf. 3. Beachten Sie alle W arnhinweise . 4. Befolgen Sie die Anw eisungen. 5. Betreiben Sie das Ger ä t nicht in der N ä he von W asser . 6. R einigen Si das Ger ä t nur mit einem trockenen Lappen. 7. V erdecken Sie keine L ü ftungsschlitze . Stellen Sie das Ger ä t nur nach den V ...

  • EAW Loudspeaker's - page 10

    V ORSICHT: V on einer falsch eingesetzten Batterie geht Gefahr aus. Ersetzen Sie Batterien nur mit dem gleiche oder gleichwertigen T yp. Diese gilt f ü r alle Lautsprecher mit Batterien. W ARNUNG: Um Feuer oder einen elektrischen Schlag zu v ermeiden, setzen Sie das Ger ä t w eder R egen noch Feuchtigkeit aus . V ermeiden Sie, dass T ropfen oder ...

  • EAW Loudspeaker's - page 11

    CA UTION: The user assumes all responsibility and liability for the proper design, installation, and use of any rigging and mounting s ystems for EA W loudspeakers. CA UTION: Accessory items are a vailable from EA W and from aftermarket suppliers to facilitate suspension, wall, ceiling, or other rigging. When using these items , review all enclosed ...

  • EAW Loudspeaker's - page 12

    PRECA UCION: T anto en EA W como en los comercios habituales de ramo tiene disponibles los accesorios necesarios para la suspensi ó n, montaje en pared o en techo o fijaci ó n de cualquier otra manera. Cuando utilice este tipo de piezas accesorias, revisetoda la documentaci ó n que venga con ellas y siga todas las instrucciones de uso y segurida ...

  • EAW Loudspeaker's - page 13

    CONTENTS Section 1 Important Safety Precautions-R ead This First . . . . . . . . . . . . ii 1.1 Important Safety Instructions for Po w ered Loudspeakers . . . . . . . ii 1 Consignes de S é curit é - À Lire en Premier . . . . . . . . . . . . . . . . . . iv 1.1 Consignes de S é curit é Importantes R elativ es Aux Enceintes A ctiv e . iv 1 Precau ...

  • EAW Loudspeaker's - page 14

    Section 9 Signal Processing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 9.1 Digital Signal Processor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 9.2 Unpow ered Loudspeakers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 9.2.1 Single-Amplified Mode . . . . . . . . . . . . . ...

  • EAW Loudspeaker's - page 15

    Sec tion 2 Unpacking 2.1 Shipping Damage Y ou should hav e visually inspected the outside of the shipping carton and noted any damage on the shipping bill you signed. After unpacking, if y ou find concealed damage to the loudspeaker , sav e the packing materials for the carrier's inspection, notify the carrier immediately and file a shipping d ...

  • EAW Loudspeaker's - page 16

    4.1 Definitions For brevity purposes , "rigging" is used herein as a general term referring to fixed mounting and suspension as well as the hardw are used for such mounting and suspension. It also applies to temporary and permanent installation. Nous utilisons le terme g é n é ral "montage" dans ce document pour d é crire le ...

  • EAW Loudspeaker's - page 17

    D ANGER: En pr é sence du moindre doute quant à l'int é grit é ou la capacit é d'un ou plusieurs é l é ments à rempli la fonction qui lui est assign é e lors du montage des enceintes, retirez imm é diatement ce ou ces é l é ments de la strucure , faites-les v é rifier ou r é parer par un personnel comp é tent, ou remplacez- ...

  • EAW Loudspeaker's - page 18

    una serie de peligros mortales potenciales en caso de que se realice de forma incorrecta. R esulta devital importancia que esta tarea sea realizada ú nicamente por t é cnicos especialistas en este tipo de intalaciones y que tengan un pleno conocimiento de todos los factores implicados, teniendo la seguridad como su primera prioridad. Solo aquella ...

  • EAW Loudspeaker's - page 19

    Exceptions: 1. Where a WLL is specified in an accompanying manual for a specific loudspeaker model, that rating supersedes this section. 2. Where the loudspeaker is specifically designed for suspension in touring applications . 4.4 Design F ac tor The Design Factor for all WLLs is a minimum of 8:1. Sec tion 5 Rigging Design 5.1 Rigging Design Pract ...

  • EAW Loudspeaker's - page 20

    Sec tion 6 Amplifier P ower Requirements This section does not apply to pow ered loudspeakers . 6.1 Selec ting an Amplifier As is true of all professional loudspeaker sy stems , the performance of the loudspeaker depends on an amplifier delivering an adequate supply of clean po w er . Determining the appropriate pow er amplifier w attage for a give ...

  • EAW Loudspeaker's - page 21

    6.1.3 Selecting An Appropriate Amplifier Size The amplifier for your loudspeaker should be sized according to both the sound lev els required and the type of audio signals that will be reproduced. This requires a considered analysis for the particular application. If y ou are unsure of ho w to determine these parameters, consult a qualified audio p ...

  • EAW Loudspeaker's - page 22

    ov erheat and puts them into a standb y mode . When the amplifiers ha ve cooled do wn to a safe operating temperature , the thermal switch will reset and the loudspeaker will resume normal operation. An amplifier Fault indicator will illuminate if a thermal switch has been activated. 7.1.4 Heat Sink V entilation The amplifiers are convection cooled ...

  • EAW Loudspeaker's - page 23

    Sec tion 8 Signal C onnections CA UTION: In spite of the listings belo w , check the input panel labeling to v erify proper connections because of possible design differences or production changes. 8.1 Audio Input C onnec tors - Unpow ered Loudspeak ers 8.1.1 Neutrik ® NL and Cannon AP ® C onnectors The input connector on the loudspeaker will be ...

  • EAW Loudspeaker's - page 24

    8.1.2 T wo Connectors If the loudspeaker has two NL or AP type connectors , they are wired in parallel so y ou can "Y -connect" multiple loudspeakers together to a single amplifier channel. This is commonly known as "dais y chaining." This will lo wer the load impedance on the amplifier . This can be calculated by this formula: ...

  • EAW Loudspeaker's - page 25

    8.2 Audio Input C onnec tions - P ow ered Loudspeak ers 8.2.1 Input Connection The audio input connector will be a female XLR-3 or a type of terminal block connector . Where both male and female XLR-3 connectors are pro vided, the input connection can be made to either . Normally , the female connector is used for the input signal, with the male co ...

  • EAW Loudspeaker's - page 26

    W ARNING: Do not defeat an y safety grounding connection to the ac mains supply to reduce ground loop noise . This is a dangerous and, in man y locales, an illegal practice . Failure to follo w this w arning may result in injury or death. 8.3.1 Input Cable For line lev el signals , use cable constructed with a shielded, twisted pair . How ever , th ...

  • EAW Loudspeaker's - page 27

    Unprocessed Input Signal: EIA-426B spectrum with an a v erage level of 0 dBu / 0.775 V Processed Output Signal: av erage lev el of 0 dBu / 0.775 V Amplifier Gain Settings: The amplifier gain setting for a single-amplified loudspeaker has no bearing on the loudspeaker's inherent performance . Choose the amplifier gain as needed for optimum sy s ...

  • EAW Loudspeaker's - page 28

    9.4 Unpow ered Loudspeak ers - Limiters CAUTION: The assumptions that must be made about ho w to set a limiter and what a driver's po w er handling limits are cannot address all conditions of use . As such, limiters cannot provide absolute protection nor pro vide an y guarantee against damage or failure from excessive inputs . A t best, they c ...

  • EAW Loudspeaker's - page 29

    9.5 P ow ered Loudspeak ers 9.5.1 External Processing Po w ered loudspeakers hav e built-in, factory set, signal processing. The settings w ere determined to provide the maximum performance in terms of frequency response , phase response , po wer handling, and audio quality . In some cases, acoustical conditions , program material, or personal tast ...

  • EAW Loudspeaker's - page 30

    A TTENTION: Si l'exposition à un niv eau sonore sup é rieur à 1 00 dB doit ê tre proong é e, portez des protections auditives dans les oreilles ou sur les oreilles . CA UTELA: In caso di esposizione prolungata a liv elli superiori a 1 00 dB, si consiglia l'impiego di tappi per le orecchie oppure di indossare cuffie protetive . PRECA ...

  • EAW Loudspeaker's - page 31

    10.4 Measurements The SmaartLive ™ computer program, from SIA Softw are Compan y , is an ideal tool to use to measure and optimize a loudspeaker sy stem or loudspeaker arra y for a particular venue . This is a fast, yet sophisticated, process that will indicate problem areas due to particular venue characteristics . Usually it is a matter of appl ...

  • EAW Loudspeaker's - page 32

    11.1 Periodic Inspection D ANGER: If there is an y question about the integrity or capability of any part used to rig a loudspeaker to perform its intended function, immediately remov e it from service for repair or replacement. D ANGER: En cas de doute sur l'int é grit é ou la capacit é d'un des é l é ments à assurer correctement s ...

  • EAW Loudspeaker's - page 33

    Inspect for problems and abnormalities including, but not limited to: 1. Bends 2. Breaks 3. Broken parts 4. Corrosion 5. Cracks 6. Cracks in w elded joints 7. Deformation 8. Denting 9. W ear 1 0. Holes 1 1. Loose or missing parts or fasteners 11.2 Periodic P er formance T esting Periodically perform listening tests and/or formal acoustical measurem ...

  • EAW Loudspeaker's - page 34

    4. Tighten all accessible screw s , nuts, and bolts , especially those that are part of the rigging hardware . 5. Clean the exterior surfaces of the enclosure and rigging s y stem as required, this largely depending on the type of "dirt". Normally , use a cloth dampened with mild soapy w ater to remo ve dust, dirt, food spills or similar ...

  • EAW Loudspeaker's - page 35

    Cosmetics: V arious finishes are used on loudspeaker enclosures depending on the product and its applications. While these finishes are designed to be durable o v er long periods, like an y applied finish, they can deteriorate ov er time , largely depending on the conditions of use. While this deterioration will not affect performance , refinish th ...

  • EAW Loudspeaker's - page 36

    3. Internal electronics (pow ered loudspeakers) 4. Enclosure and integral hardware If no problems can be traced to any of these items , look for problems with external electronics or cabling. Troubleshooting these items is bey ond the scope of this manual. 12.4.2 Drivers A faulty driver will usually cause readily audible distortions or other un w a ...

  • EAW Loudspeaker's - page 37

    12.5.1 No Sound or Low Output 1. Loudspeaker cables or connectors are mis-wired or faulty: Check all cabling. R efer to these instructions for correct loudspeaker cable connections. The best w a y to check a suspect cable is to swap it with a kno wn good cable . Read the loudspeaker's input panel to verify correct cable connections . 2. Electr ...

  • EAW Loudspeaker's - page 38

    In the case of malfunctioning electronics, contact the EA W Service Department for troubleshooting and repair instructions. Sec tion 13 C ontacting EA W In this manual we ha v e tried to answer an y questions y ou may ha v e about EA W loudspeakers. Should y ou need further assistance , please do not hesitate to contact us. Y ou can contact us in s ...

  • EAW Loudspeaker's - page 39

    Sec tion 14 W arranty Y our EA W loudspeaker is warranted against factory defects for these periods from the date of installation: Six (6) years for loudspeakers and driv ers Five (5) years for w eather protected (WP) loudspeakers products Tw o (2) years ac pow ered electronics See the warranty card packaged with the product for the complete w arra ...

  • EAW Loudspeaker's - page 40

    One Main Street, Whitinsville, MA 01588 tel: 800 992 5013 / 508 234 6158 fax: 508 234 8251 web: www .eaw .com The Laws of Physics | The Art of Listening EA W is the worldwide technological and market leader in the design and manufacture of high-performance professional loudspeaker systems. PN 425017 (E) DEC05 ...

Manufacturer EAW Category Portable Speaker

Documents that we receive from a manufacturer of a EAW Loudspeaker's can be divided into several groups. They are, among others:
- EAW technical drawings
- Loudspeaker's manuals
- EAW product data sheets
- information booklets
- or energy labels EAW Loudspeaker's
All of them are important, but the most important information from the point of view of use of the device are in the user manual EAW Loudspeaker's.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals EAW Loudspeaker's, service manual, brief instructions and user manuals EAW Loudspeaker's. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product EAW Loudspeaker's.

Similar manuals

A complete manual for the device EAW Loudspeaker's, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use EAW Loudspeaker's by users. Manuals are usually written by a technical writer, but in a language understandable to all users of EAW Loudspeaker's.

A complete EAW manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual EAW Loudspeaker's - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the EAW Loudspeaker's, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the EAW Loudspeaker's, that we can find in the current document
3. Tips how to use the basic functions of the device EAW Loudspeaker's - which should help us in our first steps of using EAW Loudspeaker's
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with EAW Loudspeaker's
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of EAW Loudspeaker's in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning EAW Loudspeaker's?

Use the form below

If you did not solve your problem by using a manual EAW Loudspeaker's, ask a question using the form below. If a user had a similar problem with EAW Loudspeaker's it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)