English dropdown-ico

Manual Crestron electronic CEN-CN

32 pages 0.87 mb
Download

Go to site of 32

Summary
  • Crestron electronic CEN-CN - page 1

    ...

  • Crestron electronic CEN-CN - page 2

    This document was prepared and written by the Technical Documentation department at: Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 1-888-CRESTRON ...

  • Crestron electronic CEN-CN - page 3

    Crestron CEN-CN Ethernet/Cresnet Interface Operations Guide - DOC. 5721 Contents • • i Contents Ethernet/Cresnet Interface: CEN -CN 1 Description 1 Functional Description 1 Physical Description 2 Leading Specifications 4 Cresnet Network Wiring 5 Configuration Setup 6 Installing Crestron Development Tools 6 Obtaining Communications 7 Troubleshoo ...

  • Crestron electronic CEN-CN - page 4

    ...

  • Crestron electronic CEN-CN - page 5

    Crestron CEN-CN Ethernet/Cresnet Interface Operations Guide - DOC. 5721 Ethernet/Cresnet Interface: CEN-CN • • 1 Ethernet/Cresnet Interface: CEN -CN Description Functional Description The CEN-CN is used to connect Crestron remote control system (herein referred to as the Cresnet system) equipment to a Crestron e-Control ™ capable control syst ...

  • Crestron electronic CEN-CN - page 6

    Ethernet/Cresnet Interface Crestron CEN -CN 2 • • Ethernet/Cresnet Interface: CEN-CN Operations Guide - DOC. 5721 Physical Description The CEN-CN, shown below, is housed in a black enclosure with silk-screened labels on the front and rear panels. On the front panel are six light-emitting diodes (LEDs) for indicating the status of the unit, the ...

  • Crestron electronic CEN-CN - page 7

    Crestron CEN-CN Ethernet/Cresnet Interface Operations Guide - DOC. 5721 Ethernet/Cresnet Interface: CEN-CN • • 3 12VDC .5 A This DC power socket connector is used to supply power via an external power pack. Crestron recommends specific power packs for its devices. The recommended power pack for the CEN-CN is Crestron part number PW-1205 ( PWI-1 ...

  • Crestron electronic CEN-CN - page 8

    Ethernet/Cresnet Interface Crestron CEN -CN 4 • • Ethernet/Cresnet Interface: CEN-CN Operations Guide - DOC. 5721 ETHERNET This 8-pin, 8-position RJ45 port connects the CEN-CN to a 10BaseT Ethernet/LAN or WAN via a hub. Refer to the table below for the pinouts. A standard (straight, non-cross-over type) Ethernet cable is required, but not suppl ...

  • Crestron electronic CEN-CN - page 9

    Crestron CEN-CN Ethernet/Cresnet Interface Operations Guide - DOC. 5721 Ethernet/Cresnet Interface: CEN-CN • • 5 Leading Specifications of the CEN-CN SPECIFICATION DETAILS Power Requirements 12VDC, external power pack or 24VDC, .25A, 6W, network Ethernet Network Type 10BaseT Ethernet Network Protocols TCP/IP, UDP/IP, ICMP (Ping), & CIP SIMP ...

  • Crestron electronic CEN-CN - page 10

    Ethernet/Cresnet Interface Crestron CEN -CN 6 • • Ethernet/Cresnet Interface: CEN-CN Operations Guide - DOC. 5721 network port, the load factor of that unit is the load factor of the entire run. The length of the run in feet and the load factor of the run should be used in the following resistance equation to calculate the value on the right si ...

  • Crestron electronic CEN-CN - page 11

    Crestron CEN-CN Ethernet/Cresnet Interface Operations Guide - DOC. 5721 Ethernet/Cresnet Interface: CEN-CN • • 7 Before installing any development tools, confirm that all other applications such as Microsoft ® Office, etc. are closed. The website and CD provide instructions for installing the various tools. When initiating a custom install fro ...

  • Crestron electronic CEN-CN - page 12

    Ethernet/Cresnet Interface Crestron CEN -CN 8 • • Ethernet/Cresnet Interface: CEN-CN Operations Guide - DOC. 5721 Typical Connections When Configuring the CEN-CN CRESTRON ELECTRONICS INC. ROCKLEIGH, N.J. 07647 USA CRESTRON ELECTRONICS INC. ROCKLEIGH, N.J. 07647 USA 12VDC .5A ETHERNET PC NET Y NET 24 G Z Z G Y 24 NET FROM EXTERNAL AC POWER PACK ...

  • Crestron electronic CEN-CN - page 13

    Crestron CEN-CN Ethernet/Cresnet Interface Operations Guide - DOC. 5721 Ethernet/Cresnet Interface: CEN-CN • • 9 5. Refer to figure below. From the Setup menu, verify that Auto Baud Search is checked. Verifying Auto Baud Search 6. Refer to figure below. While the Viewport is displayed, select Setup | Communications (alternatively, depress Alt+D ...

  • Crestron electronic CEN-CN - page 14

    Ethernet/Cresnet Interface Crestron CEN -CN 10 • • Ethernet/Cresnet Interface: CEN-CN Operations Guide - DOC. 5721 Port Settings Dialog Box 8. Select Diagnostics | Check Operating System Version (alternatively, depress F5 ) from the Viewport. The Viewport may display a window as it scans various baud rates. Eventually, a message should appear i ...

  • Crestron electronic CEN-CN - page 15

    Crestron CEN-CN Ethernet/Cresnet Interface Operations Guide - DOC. 5721 Ethernet/Cresnet Interface: CEN-CN • • 11 Updating the CEN-CN The CEN-CN contains an Operating System, a Monitor ROM, and TCP/IP Stack. All three are separate components but packaged together in a Control System Update File. Control system update files have the UPZ extensio ...

  • Crestron electronic CEN-CN - page 16

    Ethernet/Cresnet Interface Crestron CEN -CN 12 • • Ethernet/Cresnet Interface: CEN-CN Operations Guide - DOC. 5721 Update Control System Dialog Box NOTE: After a file is selected, the “Update Control System” dialog box, as shown below, will query the CEN-CN to determine what versions of the Operating system, Monitor ROM, and TCP/IP Stack ar ...

  • Crestron electronic CEN-CN - page 17

    Crestron CEN-CN Ethernet/Cresnet Interface Operations Guide - DOC. 5721 Ethernet/Cresnet Interface: CEN-CN • • 13 5. As a result of the update, a dialog box (similar to as shown below) may open and the SIMPL program (and possibly SIMPL+ modules) must be cleared. As shown below, click the Yes button. Continue with transfer? Selection Box 6. Uplo ...

  • Crestron electronic CEN-CN - page 18

    Ethernet/Cresnet Interface Crestron CEN -CN 14 • • Ethernet/Cresnet Interface: CEN-CN Operations Guide - DOC. 5721 Set IP Information via Viewport 2. Observe a dialog box similar to as shown below. As shown, the CEN -CN does not have an IP address assigned to it. IP Address Dialog Box ...

  • Crestron electronic CEN-CN - page 19

    Crestron CEN-CN Ethernet/Cresnet Interface Operations Guide - DOC. 5721 Ethernet/Cresnet Interface: CEN-CN • • 15 3. Refer to the two tables below and enter the network IP values. NOTE: If an invalid IP address is entered, the subnet mask may be CHANGED AUTOMATICALLY BY THE EQUIPMENT to an appropriate subnet mask. NOTE: To TURN OFF the TCP/IP s ...

  • Crestron electronic CEN-CN - page 20

    Ethernet/Cresnet Interface Crestron CEN -CN 16 • • Ethernet/Cresnet Interface: CEN-CN Operations Guide - DOC. 5721 Reboot Dialog Box 6. Observe a confirmation message that the IP information has been setup. After the system reboots, select Function | Cold Boot , to view the IP Information. NOTE: If an error that the viewport could not setup the ...

  • Crestron electronic CEN-CN - page 21

    Crestron CEN-CN Ethernet/Cresnet Interface Operations Guide - DOC. 5721 Ethernet/Cresnet Interface: CEN-CN • • 17 and list it in the dialog box. Modify or delete existing entries or add new ones. When all the necessary changes have been made, save the new table to disk and/or load it back into the unit. Do not overwrite the IP table in the CEN- ...

  • Crestron electronic CEN-CN - page 22

    Ethernet/Cresnet Interface Crestron CEN -CN 18 • • Ethernet/Cresnet Interface: CEN-CN Operations Guide - DOC. 5721 Typical Connections for Normal Operation CRESTRON ELECTRONICS INC. ROCKLEIGH, N.J. 07647 USA CRESTRON ELECTRONICS INC. ROCKLEIGH, N.J. 07647 USA 12VDC .5A ETHERNET PC NET Y NET 24 G Z Z G Y 24 NET TO LAN/WAN VIA HUB TO CRESNET DEVI ...

  • Crestron electronic CEN-CN - page 23

    Crestron CEN-CN Ethernet/Cresnet Interface Operations Guide - DOC. 5721 Ethernet/Cresnet Interface: CEN-CN • • 19 2. Enter the IP address of the configured CEN-CN and click the Connect button. (Within the address, X and Y may range from 0 to 255. In the example shown below, X is 1 and Y is 2.) Connect TCP/IP Address 3. The message shown below s ...

  • Crestron electronic CEN-CN - page 24

    Ethernet/Cresnet Interface Crestron CEN -CN 20 • • Ethernet/Cresnet Interface: CEN-CN Operations Guide - DOC. 5721 SIMPL™ Windows ® Example Program SIMPL (Symbol Intensive Master Programming Language) is an easy-to-use programming language that is completely integrated and compatible with all Crestron system hardware. The objects that are us ...

  • Crestron electronic CEN-CN - page 25

    Crestron CEN-CN Ethernet/Cresnet Interface Operations Guide - DOC. 5721 Ethernet/Cresnet Interface: CEN-CN • • 21 CEN-CN Troubleshooting TROUBLE POSSIBLE CAUSE(S) CORRECTIVE ACTION Improper Ethernet cable connections. Verify cable connections with LAN: proper connection is used, cable intact, and connections are secure. Improper IP addresses us ...

  • Crestron electronic CEN-CN - page 26

    Ethernet/Cresnet Interface Crestron CEN -CN 22 • • Ethernet/Cresnet Interface: CEN-CN Operations Guide - DOC. 5721 Return and Warranty Policies Merchandise Returns / Repair Service 1. No merchandise may be returned for credit, exchange, or service without prior authorization from CRESTRON. To obtain warranty service for CRESTRON products, conta ...

  • Crestron electronic CEN-CN - page 27

    Crestron CEN-CN Ethernet/Cresnet Interface Operations Guide - DOC. 5721 Glossary of Terms • • 23 Glossary of Terms CIP Cresnet (over) Internet Protocol is a combination of Cresnet and Internet protocols. On a regular Cresnet network (such as a CNMSX talking to a CT-3000 touchpanel) the low-level protocol that handles communications (such as &qu ...

  • Crestron electronic CEN-CN - page 28

    Ethernet/Cresnet Interface Crestron CEN -CN 24 • • Glossary of Terms Operations Guide - DOC. 5721 IP ID The IP ID is a two-digit hexadecimal number that is used to differentiate a given device from a group of Ethernet devices in a control system with the same IP address. Just as the Net ID is used to distinguish between identical devices within ...

  • Crestron electronic CEN-CN - page 29

    Crestron CEN-CN Ethernet/Cresnet Interface Operations Guide - DOC. 5721 Glossary of Terms • • 25 TCP/IP TCP/IP stands for Transmission Control Protocol/Internet Protocol. It is quite simply a standard set of protocols that govern the basic workings of the Internet that was implemented in 1982. The TCP part is all about ensuring that data is tra ...

  • Crestron electronic CEN-CN - page 30

    Ethernet/Cresnet Interface Crestron CEN -CN 26 • • Glossary of Terms Operations Guide - DOC. 5721 This page intentionally left blank. ...

  • Crestron electronic CEN-CN - page 31

    Crestron CEN-CN Ethernet/Cresnet Interface Operations Guide - DOC. 5721 Glossary of Terms • • 27 This page intentionally left blank. ...

  • Crestron electronic CEN-CN - page 32

    Crestron Electronics, Inc. Operations Gui de – DOC. 5721 15 Volvo Drive Rockleigh, NJ 07647 11.00 Tel: 888.CRESTRON Fax: 201.767.7576 Specifications subject to www.crestron.com change without notice. ...

Manufacturer Crestron electronic Category Network Router

Documents that we receive from a manufacturer of a Crestron electronic CEN-CN can be divided into several groups. They are, among others:
- Crestron electronic technical drawings
- CEN-CN manuals
- Crestron electronic product data sheets
- information booklets
- or energy labels Crestron electronic CEN-CN
All of them are important, but the most important information from the point of view of use of the device are in the user manual Crestron electronic CEN-CN.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Crestron electronic CEN-CN, service manual, brief instructions and user manuals Crestron electronic CEN-CN. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Crestron electronic CEN-CN.

Similar manuals

A complete manual for the device Crestron electronic CEN-CN, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Crestron electronic CEN-CN by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Crestron electronic CEN-CN.

A complete Crestron electronic manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Crestron electronic CEN-CN - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Crestron electronic CEN-CN, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Crestron electronic CEN-CN, that we can find in the current document
3. Tips how to use the basic functions of the device Crestron electronic CEN-CN - which should help us in our first steps of using Crestron electronic CEN-CN
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Crestron electronic CEN-CN
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Crestron electronic CEN-CN in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Crestron electronic CEN-CN?

Use the form below

If you did not solve your problem by using a manual Crestron electronic CEN-CN, ask a question using the form below. If a user had a similar problem with Crestron electronic CEN-CN it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)