Manual Brother NC-5100H

140 pages 0.81 mb
Download

Go to site of 140

Summary
  • Brother NC-5100H - page 1

    HL7050_US_NUG.FM5.5 Multi-Protocol Print Server NC-5100h Network User's Guide Version 0 Please read this manual thorou ghly before using the printer. You can print or vi ew this manual from the CD-ROM a t any time, please kee p the CD-ROM in a convenient place for quick and easy refe rence at all times. The Brother Solu tions Center (h ttp://s ...

  • Brother NC-5100H - page 2

    i YL4US_FAX2800MFC4800-FM5.5 Trademarks Brother is a registe red trademark of Brother Industries, Ltd. HP, HP/UX, JetDirect and JetAd min are trademarks of Hewlett-Packard Company. DEC, DEC server, VMS, LAT, and ULTRI X are trademarks of Digital Equipment Corporation. UNIX is a trademarks of UNIX Syst ems Laboratories. Ethernet is trad emark of Xer ...

  • Brother NC-5100H - page 3

    ii YL4US_FAX2800MFC4800-FM5.5 IMPORTANT NOTE: For technical and op erational assist ance, you must call. Calls must be made from within that country. In USA 1-800-276-7746 In Canada 1-877-BROTHER (514) 685-64 64 ( In Montreal ) If you have any comme nt s or sugges tions, pl ease write to us at: In Europe European Technica l Services 1 Tame Street A ...

  • Brother NC-5100H - page 4

    iii YL4US_FAX2800MFC4800-FM5.5 IMPORTANT INFORMATION: REGULATIONS Federal Communications Comm ission (FCC) Declaration of Conformity (For U.S.A. only) Responsible Party: Brother International Corporation 100 Somerset Corpo rate Boulevard Bridgewater, NJ 08807-0911, USA TEL: (908) 704-1700 declares, that the products Product Name: Brother Network Ca ...

  • Brother NC-5100H - page 5

    iv YL4US_FAX2800MFC4800-FM5.5 Declaration of Conformity (Europe) We, Brother Industries, Ltd., 15-1, Naeshiro-cho, Mizuho-ku, Nagoya 467-8561, Japan declare that this product is in conformity with the following normative documents. Safety: EN 60950, EMC: EN 55022 Class B, EN 55024 following the provisions of the Low Voltage Directive 73/23/EEC and ...

  • Brother NC-5100H - page 6

    v ZleMFC-US-FAX-4750e/5750e- Table of Contents 1 Unix Printing ......................................................................... 1-1 Printing from Unix/Linux using TCP/IP ............................. 1-1 Overview..................................................................... 1-1 TCP/IP ................................................ ...

  • Brother NC-5100H - page 7

    vi ZleMFC-US-FAX-4750e/5750e- Other Sources of Information.................................... 2-13 3 Peer to Peer Printing ............................................................ 3-1 How to Print in a Windows ® 95/98/Me Peer to Peer network ........................................................ 3-1 Overview ................................ ...

  • Brother NC-5100H - page 8

    vii ZleMFC-US-FAX-4750e/5750e- Using BRAdmin to Configure the Print Server............ 5-4 Brother Internet Print Using a Web Browser to configure the Print Server ... 5-5 Brother Internet Print Using TELNET to Configur e the Print Server ............. 5-6 Brother Internet Print Installing the BIP software on Windows ® 95/98/Me/NT4.0/2000/XP ..... ...

  • Brother NC-5100H - page 9

    viii ZleMFC-US-FAX-4750e/5750e- Other Sources of Information.................................... 6-22 7 AppleTalk (EtherTalk) TCP/IP Printing ................................ 7-1 Printing From a Macintosh ................................................ 7-1 Overview .............................................. ....................... 7-1 Macintos ...

  • Brother NC-5100H - page 10

    ix ZleMFC-US-FAX-4750e/5750e- Using DHCP to Configure the IP address ................ 10-5 Using APIPA to Configure the IP Address................ 10-5 Using ARP to Configure the Print Server IP Address .................................................... 10-6 Using RARP to Configure the IP Address ................ 10-8 Using BOOTP to Configure the ...

  • Brother NC-5100H - page 11

    x ZleMFC-US-FAX-4750e/5750e- Reloading the Print Server Firmware ............................... A-4 General ...................................................................... A-4 Reloading firmware us ing BRAdmin .......................... A-5 Reloading process ..................................................... A-6 Reloading using the FTP P ...

  • Brother NC-5100H - page 12

    UNIX PRINTING 1 - 1 1 YL4US_FAX2800MFC4800-FM5.5 1 Unix Printing Printing from Unix/Linux using TCP/IP Overview Brother print servers are supplied with the Transmission Control Protocol/Internet Protocol (TCP/IP) pr otocol suite. Since virtually all UNIX host computers support TCP/IP, this capability allows a printer to be shared on a UNIX Ethernet ...

  • Brother NC-5100H - page 13

    1 - 2 UNIX PRINTING YL4US_FAX2800MFC4800-FM5.5 5 When configuring the PRINTCAP file, pay particular attention to the service names, BINARY_P1 and TEXT_P1. TCP/IP Brother print servers appear to the network as a UNIX host computer with a unique IP address running the lpd (line printer daemon) protocol. As a result, any host computer that supports th ...

  • Brother NC-5100H - page 14

    UNIX PRINTING 1 - 3 YL4US_FAX2800MFC4800-FM5.5 The actual format of the entry may vary depending on your system, check your system documentation and also note the format of other entries in the /etc/hosts file. In any case, the node name in the /etc/hosts file must match the node name in the /etc/printcap file. Some systems such as HP/UX and AIX al ...

  • Brother NC-5100H - page 15

    1 - 4 UNIX PRINTING YL4US_FAX2800MFC4800-FM5.5 3 Configure the /etc/printcap file on each host computer to specify the local print queue, the print server name (also called remote machine or rm), and the print server service name (also called remote printer, remote queue, or rp), and the spool directory. An example of a typical printcap file: laser ...

  • Brother NC-5100H - page 16

    UNIX PRINTING 1 - 5 YL4US_FAX2800MFC4800-FM5.5 %lpc status laser1: queuing is enabled printing is enabled no entries no daemon present Users of AT&T-compatible UNIX systems can generally use the lpstat or rlpstat commands to obtain similar status information. Because this procedure varies from system to system, refer to your system documentatio ...

  • Brother NC-5100H - page 17

    1 - 6 UNIX PRINTING YL4US_FAX2800MFC4800-FM5.5 Linux Configuration If you do not wish to use the comm and line interface to configure your Linux distribution, you may wish to use the Linux Printer System Manager application on your GUI. To do this, do the following: 1 From the Linux Printer System Manager screen, click the Add button. 2 You will no ...

  • Brother NC-5100H - page 18

    UNIX PRINTING 1 - 7 YL4US_FAX2800MFC4800-FM5.5 HP/UX Configuration In the case of HP/UX10.xx, the sam program is used to set up the remote printer. The steps are as follows: 1 Execute the sam program. From the list of options, select Printers and Plotters . 2 Select LP Spooler . 3 Select Printers and Plotters . 4 Select Actions and then Add Remote ...

  • Brother NC-5100H - page 19

    1 - 8 UNIX PRINTING YL4US_FAX2800MFC4800-FM5.5 Earlier versions of HP/UX use similar procedures to 10.xx users: 1 Enter sam and select Peripheral Devices and then Add Remote Printer (not Networked printer) . 2 Enter the following remote printer settings (the other settings do not matter): ■ Line printer name (user-selectable). ■ Remote system n ...

  • Brother NC-5100H - page 20

    UNIX PRINTING 1 - 9 YL4US_FAX2800MFC4800-FM5.5 The procedure for pre-V4.0 systems is as follows. 1 Enter smit and select devices . 2 Select printer/plotter . 3 Select manage remote printer subsystem . 4 Select client services . 5 Select remote printer queues . 6 Select add a remote queue . 7 Enter the following remote queue settings: ■ Name of qu ...

  • Brother NC-5100H - page 21

    1 - 10 UNIX PRINTING YL4US_FAX2800MFC4800-FM5.5 If this is the first printer configured, you must also use the lpsched command prior to the accept command. As an alternative, you may use Printer Manager in the Admintool utility under OpenWindows. Select Edit , Add , and Add Access to Remote Printer . Then enter the print server name in the format p ...

  • Brother NC-5100H - page 22

    UNIX PRINTING 1 - 11 YL4US_FAX2800MFC4800-FM5.5 SCO UNIX requires TCP/IP V1.2 or later to work with Brother print servers. You must first configure the /etc/hosts and /etc/ printcap files as described in step 2. Then run the sysadmsh program as follows: 1 Select Printers . 2 Select Configure . 3 Select Add . 4 Enter the name of the print queue you ...

  • Brother NC-5100H - page 23

    1 - 12 UNIX PRINTING YL4US_FAX2800MFC4800-FM5.5 Use the following one-line OS/400 command to create the LPD queue: CRTOUTQ OUTQ(<queuename> RMSTSYS (*INTNETADR) RMTPRTQ(<service>) AUTOSTRWTR(1) CNNTYPE(*IP) DESTTYPE (*OTHER) MFRTYPMDL (<driver>) INTNETADR('<ipaddress>') TEXT ('<description>') where ...

  • Brother NC-5100H - page 24

    UNIX PRINTING 1 - 13 YL4US_FAX2800MFC4800-FM5.5 OS/400 version 4, 5, 5.1 You can also use the following command line to create a printer definition: CRTDEVPRT DEVD(BR2) DEV CLS(*LAN) TYPE(3812) MODEL(1) LANATTACH(*IP) PORT(9100) FONT(011) PARITY(*NONE) STOPBITS( 1) TRANSFORM(*YES) MFRTYPMDL(*HP5SI) PPRSR C1(*A4) PPRSRC2(*A4) RMTLOCNAME('10.0.0 ...

  • Brother NC-5100H - page 25

    1 - 14 UNIX PRINTING YL4US_FAX2800MFC4800-FM5.5 If you have not created a spool direct ory for the Brother print server on your UNIX host computer, you will need to do so now (the printer setup utilities in HP/UX, AIX, Solaris 2.xx, and other systems will automatically create the spool directory). The lpd spool directory is usually located in the / ...

  • Brother NC-5100H - page 26

    TCP/IP PRINTING 2 - 1 2 YL4US_FAX2800MFC4800-FM5.5 2 TCP/IP Printing Printing from Windows ® NT, Windows ® 2000/XP, LAN Server and Warp Server Overview Users of Windows ® NT can print directly to a network-ready Brother printer using the TCP/IP protocol. Microsoft Windows ® NT users must install Microsoft's "TCP/IP printing" prot ...

  • Brother NC-5100H - page 27

    2 - 2 TCP/IP PRINTING YL4US_FAX2800MFC4800-FM5.5 5 Windows ® 95/98/Me users can send print jobs using the IPP protocol via a Windows ® 2000/XP computer providing that the Microsoft Internet Print Services software is installed on the client PC, IIS is instal led and running on the Windows ® 2000/XP computer and that the client PC is using versio ...

  • Brother NC-5100H - page 28

    TCP/IP PRINTING 2 - 3 YL4US_FAX2800MFC4800-FM5.5 3 Click on Next . 4 You must now select the correct Network printing port. Select a new port from the pull-down window and select Standard TCP/IP Port . 5 When you have done that click Next . 6 The Add Standard TCP/IP Port Wizard will now appear. Click the Next button. 7 Enter the IP address, or name ...

  • Brother NC-5100H - page 29

    2 - 4 TCP/IP PRINTING YL4US_FAX2800MFC4800-FM5.5 IPP Printing from Windows ® 2000/XP Clients If you wish to print using the IPP protocol, follow these steps: 1 From the Printers folder select Add Printer . The Add Printer Wizard will now start. Click on Next . 2 For Windows ® 2000: Select Network Printer . For Windows ® XP: Select A Network Prin ...

  • Brother NC-5100H - page 30

    TCP/IP PRINTING 2 - 5 YL4US_FAX2800MFC4800-FM5.5 By using Microsoft's IPP software you can also send jobs to other printers that do not support the IPP protocol. Windows ® 2000/XP Printing (Printer Driver already installed) If you have already installed the prin ter driver and wish to configure it for network printing, follow these steps: 1 S ...

  • Brother NC-5100H - page 31

    2 - 6 TCP/IP PRINTING YL4US_FAX2800MFC4800-FM5.5 6 Configure the host IP address, subne t mask, and gateway address in that dialog. Consult your sy stem manager f or these addresses. 7 Click OK to exit (your NT workstation or server will need to be re-booted). Windows ® NT 4.0 Printing Installing the Brother Peer to Peer Software 1 Start the CD-RO ...

  • Brother NC-5100H - page 32

    TCP/IP PRINTING 2 - 7 YL4US_FAX2800MFC4800-FM5.5 Windows ® NT 4.0 Printing Associating to the Printer You must now create a printer on your Windows ® system using the standard Windows ® printer setup procedure. 1 To do this, go to the Start button, select Settings and then Printers . 2 Double click the Add Printer icon to get the Add Printer Wiz ...

  • Brother NC-5100H - page 33

    2 - 8 TCP/IP PRINTING YL4US_FAX2800MFC4800-FM5.5 Windows ® NT 4.0 Printing Adding a Second Brother LPR Port You do not need to re-run the install program to add a new Brother LPR port. Instead, press the Start button, select Settings , and open the Printers window. Click on the icon of the printer that you wish to configure, select File from the m ...

  • Brother NC-5100H - page 34

    TCP/IP PRINTING 2 - 9 YL4US_FAX2800MFC4800-FM5.5 Windows ® NT 3.5x Printing (Printer Driver not yet installed) If you have Windows ® NT 3.5 or 3.51, use the following procedure to configure the print server. 1 Go to the Main window and select the Print Manager icon. 2 Select Printer menu. 3 Select Create Printer . 4 Enter any name for the Printer ...

  • Brother NC-5100H - page 35

    2 - 10 TCP/IP PRINTING YL4US_FAX2800MFC4800-FM5.5 LAN Server, OS/2 Warp Server Configuration Brother print servers will work with IBM LAN Server, OS/2 Warp Server networks that have IBM TCP/IP V2.0 or later installed on the file server (TCP/IP is supplied as standard with LAN Server V4.0 and later as well as Warp Server). Use the following procedur ...

  • Brother NC-5100H - page 36

    TCP/IP PRINTING 2 - 11 YL4US_FAX2800MFC4800-FM5.5 5 Choose the output port. IBM TCP/IP automatically creates 8 named pipes called PIPELPD0 through to PIPELPD7 . Pick an unused port and double click on it. You will get the Settings window. Enter the following: You may leave the other ent ries blank. Click on the OK button. The pipe should be hig ...

  • Brother NC-5100H - page 37

    2 - 12 TCP/IP PRINTING YL4US_FAX2800MFC4800-FM5.5 4 Select Create . Enter the following: 5 Exit the LAN Requester program. 6 You should now be able to print. To test the queue, type the following from either the OS/2 command prompt or from a DOS workstation: 7 COPY C:CONFIG.SYS servernamealias 8 Where servername is the name of the file server a ...

  • Brother NC-5100H - page 38

    TCP/IP PRINTING 2 - 13 YL4US_FAX2800MFC4800-FM5.5 Other Sources of Information 1 Visit http://solutions.brother.com/ for more information on network printing and for documents on the IPP protocol and how to configure a Windows ® 2000/XP/95/98/Me System. 2 Refer to chapter 10 of this user guide to learn how to configure the IP address of the printe ...

  • Brother NC-5100H - page 39

    3 - 1 PEER TO PEER PRINTING 3 YL4US_FAX2800MFC4800-FM5.5 3 Peer to Peer Printing How to Print in a Windows ® 95/98/Me Peer to Peer network Overview Microsoft's Windows ® 95/98/Me operating systems feature built-in networking capabilities. These capabilities allow a Windows ® PC to be configured as a client workstation in a file server based ...

  • Brother NC-5100H - page 40

    PEER TO PEER PRINTING 3 - 2 YL4US_FAX2800MFC4800-FM5.5 4 Windows ® 95/98/Me users can send print jobs using the IPP protocol via a Windows ® 2000 computer providing that the Microsoft Internet Print Services software is installed on the client PC, IIS is installed and running on the Windows ® 2000 and that the client PC is using version 4 or lat ...

  • Brother NC-5100H - page 41

    3 - 3 PEER TO PEER PRINTING YL4US_FAX2800MFC4800-FM5.5 Installing the Brother Peer to Peer Software 1 Start the CD-ROM installation menu program according to the Quick Setup Guide. 2 Select the proper model and then the Software Installation menu. Then select the appropriate menu to start the Brother Network Print Software installation program. 3 P ...

  • Brother NC-5100H - page 42

    PEER TO PEER PRINTING 3 - 4 YL4US_FAX2800MFC4800-FM5.5 8 Click the OK button. When prompted you must re-boot your computer. Associating to the printer You must now create a printer on your Windows ® system using the standard Windows ® printer setup procedure. 1 To do this, go the Start button, select Settings and then Printers . 2 Select Add Prin ...

  • Brother NC-5100H - page 43

    3 - 5 PEER TO PEER PRINTING YL4US_FAX2800MFC4800-FM5.5 Adding a Second Brother LPR Port You do not re-run the install program to add a new Brother LPR port. Instead, press the Start button, select Settings , and open the Printers window. Click on the icon of the printer that you wish to configure, select File from the menu bar, and then choose Prop ...

  • Brother NC-5100H - page 44

    NETBIOS PEER TO PEE R PRINTING 4 - 1 4 YL4US_FAX2800MFC4800-FM5.5 4 NetBIOS Peer to Peer Printing How to Print using NetBIOS in Windows ® 95/98/Me/NT/2000/XP, LAN Server and OS/2 Warp Server Overview Brother print server range suppor ts SMB (Server Message Block) over the TCP/IP protocol via the Ne tBIOS interface. This means that just like regula ...

  • Brother NC-5100H - page 45

    4 - 2 NETBIOS PEER TO PEER PRINTING YL4US_FAX2800MFC4800-FM5.5 Print Server Configuration In order for this function to work, you must correctly change the DOMAIN name or WORKGROUP name to match that of your network. Once this is done, the pr int server will appear automatically in your network neighborhood and you will be able to send print docume ...

  • Brother NC-5100H - page 46

    NETBIOS PEER TO PEE R PRINTING 4 - 3 YL4US_FAX2800MFC4800-FM5.5 Changing the workgroup/ domain name using TELNET or BRCONFIG or a web browser If you are unable to use the BRAdmin application, you can use TELNET, a web browser or the BRCONFIG Remote console program (BRCONFIG requires the IP X/SPX protocol to be installed on your PC). When you are co ...

  • Brother NC-5100H - page 47

    4 - 4 NETBIOS PEER TO PEER PRINTING YL4US_FAX2800MFC4800-FM5.5 NetBIOS Port Monitor for Windows ® 95/98/Me, NT4.0/2000/XP This software requires the TCP/IP transport protocols to be installed on your Windows ® 95/98/Me, NT4.0/2000/XP computer. To install those protocols refer to your Windows ® documentation. If you are using the TCP/IP protocol, ...

  • Brother NC-5100H - page 48

    NETBIOS PEER TO PEE R PRINTING 4 - 5 YL4US_FAX2800MFC4800-FM5.5 7 You must now enter the server name and port name for the actual print server. You can use the Browse button to search for the print server, select the domain/workgroup name, and then the server is listed. If the print server does not automatically appear in your browse list, then you ...

  • Brother NC-5100H - page 49

    4 - 6 NETBIOS PEER TO PEER PRINTING YL4US_FAX2800MFC4800-FM5.5 4 Select Local Printer when you are asked how the printer is connected to your computer, and then push Next . 5 Select the correct driver. Click Next when you are done. 6 If you have selected a printer driver that is already being used, you have the option of either keeping the existing ...

  • Brother NC-5100H - page 50

    NETBIOS PEER TO PEE R PRINTING 4 - 7 YL4US_FAX2800MFC4800-FM5.5 7 If you have selected a printer driver that is already used, you have the option of either keeping the existing driver (recommended) or replacing it. Select the desired option and press Next . 8 Enter any desired name for the Brother printer and press Next . For example, you could cal ...

  • Brother NC-5100H - page 51

    4 - 8 NETBIOS PEER TO PEER PRINTING YL4US_FAX2800MFC4800-FM5.5 Windows NT ® 4.0 / Windows ® 2000/XP 2 Click on the Port/s tab and push the Add Port button. In the Add Port dialog, highlight Brother NetBIOS port . Click New Port and enter the port name. The default port name is BNT1. If you have already used this name, you will get an error messag ...

  • Brother NC-5100H - page 52

    NETBIOS PEER TO PEE R PRINTING 4 - 9 YL4US_FAX2800MFC4800-FM5.5 Workstation Configuration: On each workstation that you wish to print from, execute the following step: Go to the DOS or OS/2 command prompt and enter the command: NET USE LPTx: NodeNameServiceName Where x is the LPT port number (1 through 9), NodeName is the NetBIOS Name of the pri ...

  • Brother NC-5100H - page 53

    5 - 1 CONFIGURING INTERNET PRINTING FOR WINDOWS ® 5 YL4US_FAX2800MFC4800-FM5.5 5 Configuring Internet Printing for Windows ® Internet Printing Installation Overview Brother's Brother Internet Print (BIP) software, for Windows ® 95/98/ Me/NT4.0, allows a PC user at one location to send a print job to a Brother Printer at a remote locati on v ...

  • Brother NC-5100H - page 54

    CONFIGURING INTERNET PRINTING FOR WINDOWS ® 5 - 2 YL4US_FAX2800MFC4800-FM5.5 5 Windows ® 95/98/Me users can send print jobs using the IPP protocol via Windows ® 2000 computer, provided that the Microsoft Internet Print Services software is installed on the client PC, Internet Information Server (IIS) is installed and running on the server and th ...

  • Brother NC-5100H - page 55

    5 - 3 CONFIGURING INTERNET PRINTING FOR WINDOWS ® YL4US_FAX2800MFC4800-FM5.5 ■ At the remote site, an E-mail server receives the E-mail message. The remote print server, which has its own E-mail address, uses the POP3 protocol (Post Office Pr otocol 3) to download the E-mail message from the e-mail server. It then decodes the attachment and prin ...

  • Brother NC-5100H - page 56

    CONFIGURING INTERNET PRINTING FOR WINDOWS ® 5 - 4 YL4US_FAX2800MFC4800-FM5.5 Brother Internet Print Using BRAdmin to Configure the Print Server The steps required to configure the pr int server to receive print jobs from a Windows ® 95/98//Me/NT4.0/2000/XP. PC running the BIP software is as follows: 1 Start BRAdmin. 2 Select the node name of the ...

  • Brother NC-5100H - page 57

    5 - 5 CONFIGURING INTERNET PRINTING FOR WINDOWS ® YL4US_FAX2800MFC4800-FM5.5 7 The print server is configured by default to poll the POP3 server every 30 seconds. You may change this value, if desired. 8 If you have enabled notification, enter the address of your SMTP server (consult your network administrator if you do not know this address). 9 P ...

  • Brother NC-5100H - page 58

    CONFIGURING INTERNET PRINTING FOR WINDOWS ® 5 - 6 YL4US_FAX2800MFC4800-FM5.5 Brother Internet Print Using TELNET to Configure the Print Server 1 When you get the Local> prompt after connecting to the console, enter the command: SET POP3 ADDRESS address where ipaddress is the address of your POP3 server (consult with your network administrator i ...

  • Brother NC-5100H - page 59

    5 - 7 CONFIGURING INTERNET PRINTING FOR WINDOWS ® YL4US_FAX2800MFC4800-FM5.5 Brother Internet Print Installing the BIP software on Windows ® 95/98/Me/NT4.0/2000/XP To install the BIP software on a Windows ® 95/98/NT4.0/2000/XP PC, execute the following steps: Setup from CD-ROM 1 Start the CD-ROM installation menu program according to the Quick S ...

  • Brother NC-5100H - page 60

    CONFIGURING INTERNET PRINTING FOR WINDOWS ® 5 - 8 YL4US_FAX2800MFC4800-FM5.5 9 You will then be asked to enter the port settings for the remote print server: Enter any unique legal Internet E-mail address for the remote print server (for example emailprinter@xyz.com). Note that Internet E-mail addresses cannot have spaces in them. Enter your E-mai ...

  • Brother NC-5100H - page 61

    5 - 9 CONFIGURING INTERNET PRINTING FOR WINDOWS ® YL4US_FAX2800MFC4800-FM5.5 17 Select the Brother Internet port (BIP...) which you selected in step 6 and press Next . <For Windows ® NT4.0/2000/XP users> 15 Select the Brother Internet port (BIP...) which you selected in step 6 and press Next . 16 Select the desired model of the remote print ...

  • Brother NC-5100H - page 62

    CONFIGURING INTERNET PRINTING FOR WINDOWS ® 5 - 10 YL4US_FAX2800MFC4800-FM5.5 Adding a Second Brot her Internet Port You should not re-run the instal l program to add a new Brother Internet Port. Instead, press the Start button, select Settings , and open the Printers window. Click on the icon of a printer that is using BIP, select File from the m ...

  • Brother NC-5100H - page 63

    5 - 11 CONFIGURING INTERNET PRINTING FOR WINDOWS ® YL4US_FAX2800MFC4800-FM5.5 5 When you click Next , Windows ® 2000/XP will make a connection with the URL that you specified. IF THE PRINTER DRIVER HA S ALREADY BEEN INSTALLED If the appropriate printer driver is already installed on your PC, Windows ® 2000/XP will automatically use that driver f ...

  • Brother NC-5100H - page 64

    CONFIGURING INTERNET PRINTING FOR WINDOWS ® 5 - 12 YL4US_FAX2800MFC4800-FM5.5 Specifying a different URL Please note that there are several pos sible entries that you can enter for the URL field. http://printer_ip_address:631/ipp This is the default URL and we recommend that you use this URL. Please note the Get More Info option will not display a ...

  • Brother NC-5100H - page 65

    6 - 1 NOVELL NETWARE PRINTING 6 YL4US_FAX2800MFC4800-FM5.5 6 Novell NetWare Printing How to configure Novell NetWare Printing Overview Brother print servers allow NetWare client PCs to print jobs on the same printer as TCP/IP or other net work protocol users. All NetWare jobs are spooled through the Novell server and delivered to the printer when i ...

  • Brother NC-5100H - page 66

    NOVELL NETWARE PRINTING 6 - 2 YL4US_FAX2800MFC4800-FM5.5 General Information In order to use a Brother print server on a NetWare network, one or more file servers must be configur ed with a print queue that the print server can service. Users send their print requests to the file server's print queue, and the jobs are then spooled (either dire ...

  • Brother NC-5100H - page 67

    6 - 3 NOVELL NETWARE PRINTING YL4US_FAX2800MFC4800-FM5.5 Creating a NDPS Printer Using NWADMI N for NetWare5 With NetWare 5, Novell has released a new preferred printing system called Novell Distributed Prin t Services (NDPS). Before the print server can be configured, NDPS must be installed on the NetWare 5 server and an NDPS Manager configured on ...

  • Brother NC-5100H - page 68

    NOVELL NETWARE PRINTING 6 - 4 YL4US_FAX2800MFC4800-FM5.5 NDPS Broker When NDPS is installed, an NDPS broker is loaded onto the network. One of the Broker services Resource Management Service allows Printer Drivers to be installed onto the server for use with Printer Agents. To add a Printer Driver to the Broker: 1 Make sure the Resource Management ...

  • Brother NC-5100H - page 69

    6 - 5 NOVELL NETWARE PRINTING YL4US_FAX2800MFC4800-FM5.5 Creating a Printer Agent Follow the steps below to create a Printer Agent for the control access printer (NDS object). 1 In NetWare Administrator, select object | create | NDPS Printer . Enter the NDPS printer name. 2 If this is a new printer select create A New Printer Agent . 3 If there is ...

  • Brother NC-5100H - page 70

    NOVELL NETWARE PRINTING 6 - 6 YL4US_FAX2800MFC4800-FM5.5 4 Enter the name you wish the Prin ter Agent to be referred to by, and select Novell Printer Gateway for the Gateway type and click OK . 5 Select None for the printer Type, and Novell Port Handler for the Port Handler Type. Then click OK . 6 You must now specify the type of connection that yo ...

  • Brother NC-5100H - page 71

    6 - 7 NOVELL NETWARE PRINTING YL4US_FAX2800MFC4800-FM5.5 names are BRN_xxxxxx , where xxxxxx is the last six digits of the Ethernet address (MAC address)). 4 Select the print server that you wish to configure and double click it. You will be asked for a password. The default password is access . 5 Select the NetWare tab. a If it is not already sele ...

  • Brother NC-5100H - page 72

    NOVELL NETWARE PRINTING 6 - 8 YL4US_FAX2800MFC4800-FM5.5 Configuring the Brot her Print Server (Queue Server Mode in NDS mode) using BRAdmin 1 Make sure that you logged in as ADMIN in NDS mode. 2 Start BRAdmin. 3 One or more print server services will appear in the list of printers (the default node names are BRN_xxxxxx , where xxxxxx is the last s ...

  • Brother NC-5100H - page 73

    6 - 9 NOVELL NETWARE PRINTING YL4US_FAX2800MFC4800-FM5.5 e Your queue name will appear in the TREE and Context that you specified. Select the queue and click on Add . The queue name will then be transferred to the Service Print Queues Window. You will be able to see the TREE and Context information along with the queue name information in this Wind ...

  • Brother NC-5100H - page 74

    NOVELL NETWARE PRINTING 6 - 10 YL4US_FAX2800MFC4800-FM5.5 7 Change context if required and t hen double click the name of the printer you created in step 3. 8 Click Assignments . 9 Click Add . 10 Change the context if necessary. 11 Select the print queue you created in step 5. 12 Click Configuration and set the Printer type to Other/ Unknown . Clic ...

  • Brother NC-5100H - page 75

    6 - 11 NOVELL NETWARE PRINTING YL4US_FAX2800MFC4800-FM5.5 18 Start the appropriate BRAdmin application, and select the correct print server from the list (by default, the node name is BRN_xxxxxx , where xxxxxx is the last six digits of the Ethernet address (MAC address)). 19 Double click the appropriate Brother print server. You will be prompted fo ...

  • Brother NC-5100H - page 76

    NOVELL NETWARE PRINTING 6 - 12 YL4US_FAX2800MFC4800-FM5.5 Configuring the Brother Print Server (Remote Printer Mode in NDS mode) using Novell NWAdmin and BRAdmin To configure a Brother print server for remote printer mode with NWADMIN (NetWare Administrator utility) and BRAdmin, you will need to perform the following steps: 1 Make sure that the PSE ...

  • Brother NC-5100H - page 77

    6 - 13 NOVELL NETWARE PRINTING YL4US_FAX2800MFC4800-FM5.5 12 Change context if necessary and select the print queue you created. Click OK and then OK again, and then exit NWADMIN. 13 Start the appropriate BRAdmin application, and select the correct print server you wish to configure (by default, the node names will begin with BRN_xxxxxx_P1 ) 14 Dou ...

  • Brother NC-5100H - page 78

    NOVELL NETWARE PRINTING 6 - 14 YL4US_FAX2800MFC4800-FM5.5 Configuring the Brother Print Server (Queue Server Mode in Bindery emulation mode) using PCONSOLE and BRCONFIG 1 Login as Supervisor (NetWare 3.xx) or ADMIN (NetWare 4.1x or later; be sure to specify the /b option for bindery mode). 2 Execute BRCONFIG from the Windows ® menu. 3 Select the c ...

  • Brother NC-5100H - page 79

    6 - 15 NOVELL NETWARE PRINTING YL4US_FAX2800MFC4800-FM5.5 11 Press INSERT to create a new queue on the file server, type the new queue name and press ENTER. The name does not have to be related to the name of the print server resources, but should be short and convenient for users to remember. 12 Make sure that the new queue name is highlighted, an ...

  • Brother NC-5100H - page 80

    NOVELL NETWARE PRINTING 6 - 16 YL4US_FAX2800MFC4800-FM5.5 Configuring the Brother Print Server (Queue Server Mode in NDS mode) using PCONSOLE and BRCONFIG 1 Make sure that you are logged in as ADMIN in NDS mode on the NetWare 4.1x file server. 2 Run the PCONSOLE utility from PC workstation. 3 Select print servers from the Available Options menu. 4 ...

  • Brother NC-5100H - page 81

    6 - 17 NOVELL NETWARE PRINTING YL4US_FAX2800MFC4800-FM5.5 10 Press INSERT to get a list of the queue server candidates and select the NetWare print server name from step 4, which will then be added to the list. Press ENTER. And then, press ESCAPE several times to return to the main Available Options menu. 11 Select Printers from the Available Optio ...

  • Brother NC-5100H - page 82

    NOVELL NETWARE PRINTING 6 - 18 YL4US_FAX2800MFC4800-FM5.5 21 Execute the BRCONFIG from the Windows ® menu. Select the print server from the list of print servers. When you get the message that the print server is connected, press the ENTER key and type the default password of access in response to the # prompt (the password will not echo), and the ...

  • Brother NC-5100H - page 83

    6 - 19 NOVELL NETWARE PRINTING YL4US_FAX2800MFC4800-FM5.5 Configuring the Brother Print Server (Remote Printer Mode) using PCONSOLE and BRCONFIG 1 Make sure that the PSERVER NLM (NetWare Loadable Module) is loaded on your file server. 2 Log into the file server from your PC workstation as ADMIN if you are using NetWare 4.1x (if y ou want NDS suppor ...

  • Brother NC-5100H - page 84

    NOVELL NETWARE PRINTING 6 - 20 YL4US_FAX2800MFC4800-FM5.5 g Highlight Print Queues Assigned and press ENTER and then INSERT to get a list of available queues. h Highlight the name of the print queue you wish to assign to the remote printer and press ENTER. i The other settings in the menu are not required. Push ESCAPE several times to exit PCONSOLE ...

  • Brother NC-5100H - page 85

    6 - 21 NOVELL NETWARE PRINTING YL4US_FAX2800MFC4800-FM5.5 Assigning the Remote printer name and number using BRCONFIG 7 a Execute the BRCONFIG from the Windows ® menu. b Select the Brother print server from the list of print servers. When you get the message that t he print server is connected, press the ENTER key and type the default password acc ...

  • Brother NC-5100H - page 86

    NOVELL NETWARE PRINTING 6 - 22 YL4US_FAX2800MFC4800-FM5.5 Other Sources of Information 1 Visit http://solutions.brother.com/ for more information on network printing. 2 Refer to chapter 10 of this user guide to learn how to configure the IP address of the printer. The same services assigned by NetWare print server name cannot be used for both queue ...

  • Brother NC-5100H - page 87

    APPLETALK (ETHERTALK) TCP/IP PRINTING 7 - 1 7 YL4US_FAX2800MFC4800-FM5.5 7 AppleTalk (EtherTalk) TCP/IP Printing Printing From a Macintosh Overview Brother print servers support the AppleTalk protocol running over Ethernet (also known as EtherTalk). This allows Macintosh users to print at the same time as all other Ethernet network using the AppleT ...

  • Brother NC-5100H - page 88

    APPLETALK (ETHERTALK) TC P/IP PRINTING 7 - 2 YL4US_FAX2800MFC4800-FM5.5 Quick Tips: Macintosh Configuration (OS 8.5 - 9.2) Your Brother Printer is compatible with the standard Apple LaserWriter 8 printer driver (earlier versions of the LaserWriter drivers may crash or cause PostScript errors on large networks). If you do not have the LaserWriter 8 ...

  • Brother NC-5100H - page 89

    7 - 3 APPLETALK (ETHER TALK) TCP/IP PRINTING YL4US_FAX2800MFC4800-FM5.5 The appropriate PPD file supplied with your printer must first be installed. Insert the CD-ROM into the CD-ROM drive of your computer. Select the Start Here icon, select your language and follow the on-screen instructions for Install Software . Figure 1 Typical Macintosh Instal ...

  • Brother NC-5100H - page 90

    APPLETALK (ETHERTALK) TC P/IP PRINTING 7 - 4 YL4US_FAX2800MFC4800-FM5.5 1 Open the Chooser from the Apple Menu on the Macintosh, and then click on the LaserWriter icon (if necessary, select the appropriate AppleTalk zone from the Network Control Panel ). Figure 2 Macintosh Chooser 2 Click on the appropriate print server and close the Chooser progra ...

  • Brother NC-5100H - page 91

    7 - 5 APPLETALK (ETHER TALK) TCP/IP PRINTING YL4US_FAX2800MFC4800-FM5.5 How to Select the Print Server (TCP/IP) Apple has developed the "Desktop Printer" utility. This can be found from the Apple menu (this is only available from System 8.6 or later). When you run it you will see the following screen: Figure 3 Selecting LPR Printing ...

  • Brother NC-5100H - page 92

    APPLETALK (ETHERTALK) TC P/IP PRINTING 7 - 6 YL4US_FAX2800MFC4800-FM5.5 1 Select the Printer (LPR ) option and click OK . You will then see the following: Figure 4 Selecting the PPD and LPR Configuration 2 At this point we must select t he correct PPD file for the printer and also configure the correct LPR information. Click the Change button in th ...

  • Brother NC-5100H - page 93

    7 - 7 APPLETALK (ETHER TALK) TCP/IP PRINTING YL4US_FAX2800MFC4800-FM5.5 Figure 5 Entering the IP address and Queue 5 Click OK to go back to the previous screen. 6 You are now ready to create the printer for use. To do that, click the Create button and you will see the following: Figure 6 Saving the printer to the Desktop (screen shown is from the H ...

  • Brother NC-5100H - page 94

    APPLETALK (ETHERTALK) TC P/IP PRINTING 7 - 8 YL4US_FAX2800MFC4800-FM5.5 Macintosh Configuration (OS X v. 10/10.1/10.2) The appropriate PPD file supplied with your printer must be installed. Insert the CD-ROM into the CD-ROM drive of your computer. Select the Mac OS X folder. Double click on the PPD_Installer.pkg icon and follow the on-screen instru ...

  • Brother NC-5100H - page 95

    7 - 9 APPLETALK (ETHER TALK) TCP/IP PRINTING YL4US_FAX2800MFC4800-FM5.5 Printing the configuration page will allow you to confirm the MAC address. Please refer to the Quick Setup Guide for information on how to print the configuration page. 8 From the Printer Model pull-down list select your model. 9 Click Add and the printer will be available from ...

  • Brother NC-5100H - page 96

    APPLETALK (ETHERTALK) TC P/IP PRINTING 7 - 10 YL4US_FAX2800MFC4800-FM5.5 Changing the Configuration From a Macintosh, the easiest way to change the printer or print server parameters is to use a web browser. Simply connect to the pr inter using the format: http://ip_address where ip_address is the address of the printer. Other Sources of Informatio ...

  • Brother NC-5100H - page 97

    DLC PRINTING 8 - 1 8 YL4US_FAX2800MFC4800-FM5.5 8 DLC Printing Printing from Windows ® NT or Windows ® 2000 Overview DLC is a simple protocol that is included in Windows NT ® and Windows ® 2000 as standard. It can be used on other operating systems (such as Windows ® 3.x) with the addition of vendor-supplied software that supports the Hewlett- ...

  • Brother NC-5100H - page 98

    DLC PRINTING 8 - 2 YL4US_FAX2800MFC4800-FM5.5 3 Select DLC Protocol and then OK or Add if using Windows ® 2000. You may be asked for the location of the files. For Intel based computers, the necessary files are stored in the i386 directory of the Windows ® NT CD-ROM. If you have a non-Intel platform, specify the correct directory on your Windows ...

  • Brother NC-5100H - page 99

    8 - 3 DLC PRINTING YL4US_FAX2800MFC4800-FM5.5 9 The selected print server address will then appear in the smaller box under Card Address . 10 Type in any desired name for the port (the name must not be the name of an existing port or DOS device, such as LPT1) and click OK then on the Printer Ports screen, click Next . 11 Select the correct driver c ...

  • Brother NC-5100H - page 100

    DLC PRINTING 8 - 4 YL4US_FAX2800MFC4800-FM5.5 5 A list of available print server MAC addresses (Ethernet addresses) appears in the larger box under Card Address . Select the address of the desired print server (you can see the Ethernet address on the printer configuration page). 6 The selected print server addres s will then appear in the smaller b ...

  • Brother NC-5100H - page 101

    8 - 5 DLC PRINTING YL4US_FAX2800MFC4800-FM5.5 6 Click on Hewlett-Packard Network Port . 7 Type in your desired name for the port (this name must not be an existing port or DOS device, such as LPT1). 8 The MAC addresses (Ethernet addresses) of available print servers will appear in the Card Address menu. Select the desired address (You can see the E ...

  • Brother NC-5100H - page 102

    DLC PRINTING 8 - 6 YL4US_FAX2800MFC4800-FM5.5 The final step is to create a printer using the normal operating system printer setup method. The only difference is that instead of connecting the printer to the LPT1 parallel port, you point it to the network port you just created. Other Sources of Information Visit http://solutions.brother.com/ for m ...

  • Brother NC-5100H - page 103

    WEB BASED MANAGEMENT 9 - 1 9 YL4US_FAX2800MFC4800-FM5.5 9 Web Based Management How to use a Web Browser to manage your Device Overview A standard Web Browser (we recommend Netscape Navigator version 4.0 or later/Microsoft Internet Explorer version 5.0 or later) can be used to manage your printer using the HTTP (Hyper Text Transfer Protocol). You ca ...

  • Brother NC-5100H - page 104

    WEB BASED MANAGEMENT 9 - 2 YL4US_FAX2800MFC4800-FM5.5 3 The default password for Brother print servers is access . 4 You can use a web browser on most computing platforms, for example, Macintosh and Unix users are also able to connect to the printer and manage it. 5 You can also use the BRAd min application to manage the printer and its network con ...

  • Brother NC-5100H - page 105

    TCP/IP CONFIGURATION 10 - 1 10 YL4US_FAX2800MFC4800-FM5.5 10 TCP/IP Configuration Assigning TCP/IP Information Overview The TCP/IP protocol requires t hat each device on the network have it's own unique IP address. Use the following information to learn about IP address configuration. The Automatic Private IP Addressi ng (APIPA) protocol autom ...

  • Brother NC-5100H - page 106

    TCP/IP CONFIGURATION 10 - 2 YL4US_FAX2800MFC4800-FM5.5 ■ Other SNMP based management utility. These configuration methods are des cribed in the fo llowing paragraphs. Using the printer cont rol panel to allocate an IP address (printer s with LCD panels only) Refer to the Quick Setup Guide for details on how to configure IP address information usi ...

  • Brother NC-5100H - page 107

    10 - 3 TCP/IP CONFIGURATION YL4US_FAX2800MFC4800-FM5.5 The BRAdmin application can use t he IPX/SPX or TCP/IP protocols to communicate with the Brother print server. If you wish to use the TCP/IP protocol to manage the print server make sure that the print server has a valid IP address. There are two ways to change the IP address using the BRAdmin ...

  • Brother NC-5100H - page 108

    TCP/IP CONFIGURATION 10 - 4 YL4US_FAX2800MFC4800-FM5.5 6 Click OK . Restart the print server by using BRAdmin, Web Browser or TELNET. If you are not sure how to restart the print server, you may simply turn the printer’s power switch off, and then switch it on. Using BRAdmin and the TCP/IP Protocol to set the IP address If your PC is using the TC ...

  • Brother NC-5100H - page 109

    10 - 5 TCP/IP CONFIGURATION YL4US_FAX2800MFC4800-FM5.5 Using DHCP to Configure the IP address The Dynamic Host Configuration Pr otocol (DHCP) is one of several automated mechanisms for IP addre ss allocation. If you have DHCP Server in your network (typically a Unix/Linux, Windows NT ® 4.0, Windows ® 2000 or Novell Netware network) the print serv ...

  • Brother NC-5100H - page 110

    TCP/IP CONFIGURATION 10 - 6 YL4US_FAX2800MFC4800-FM5.5 Using ARP to Configure the Print Server IP Address If you are unable to use the BRAdmin application or the printer’s control panel and your network does not use a DHCP server, you can also use the ARP command. The ARP command is available on Windows ® systems that have TCP/IP installed as we ...

  • Brother NC-5100H - page 111

    10 - 7 TCP/IP CONFIGURATION YL4US_FAX2800MFC4800-FM5.5 Unix/Linux Systems Typically, Unix systems require the hash "-" character between each digit of the Ethernet address. arp -s 192.189.207.2 00-80-77-31-01-07 To configure the print server and to verify the connection, enter the following command ping ipaddress where ipaddress is the IP ...

  • Brother NC-5100H - page 112

    TCP/IP CONFIGURATION 10 - 8 YL4US_FAX2800MFC4800-FM5.5 Using RARP to Config ure the IP Address The Brother print server’s IP address can be configured using the Reverse ARP (rarp) facility on your host computer. This is done by editing the /etc/ethers file (if this file does not exist, you can create it) with an entry similar to the following: 00 ...

  • Brother NC-5100H - page 113

    10 - 9 TCP/IP CONFIGURATION YL4US_FAX2800MFC4800-FM5.5 Using BOOTP to Configure the IP Address BOOTP is an alternative to rarp that has the advantage of allowing configuration of the subnet mask and gateway. In order to use BOOTP to configure the IP address make sure that BOOTP is installed and running on your host computer (it should appear in the ...

  • Brother NC-5100H - page 114

    TCP/IP CONFIGURATION 10 - 10 YL4US_FAX2800MFC4800-FM5.5 Certain BOOTP host software implementations will not respond to BOOTP requests if you have not included a download filename in the configuration file; if this is the ca se, simply create a null file on the host and specify the name of this file and its path in the configuration file. As with r ...

  • Brother NC-5100H - page 115

    10 - 11 TCP/IP CONFIGURATION YL4US_FAX2800MFC4800-FM5.5 If you do not have any subnets, use one of the following default subnet masks: 255.255.255.0 for class C networks 255.255.0.0 for class B networks 255.0.0.0 for class A networks The leftmost group of digits in your IP address can identify the type of network you have. The value of this group r ...

  • Brother NC-5100H - page 116

    TCP/IP CONFIGURATION 10 - 12 YL4US_FAX2800MFC4800-FM5.5 You will then get the Local> prompt. Type SET IP ADDRESS ipaddress , where ipaddress is the desired IP address you wish to assign to the print server (che ck with your network manager for the IP address to use). For example: Local> SET IP ADDRESS 192.189.207.3 You will now need to set t ...

  • Brother NC-5100H - page 117

    10 - 13 TCP/IP CONFIGURATION YL4US_FAX2800MFC4800-FM5.5 Other Sources of Information Visit http://solutions.brother.com/ for more information on TCP/IP protocol. ...

  • Brother NC-5100H - page 118

    11 - 1 TROUBLESHOOTING 11 YL4US_FAX2800MFC4800-FM5.5 11 Troubleshooting Overview This chapter describes procedures for troubleshooting problems you may encounter with a Brother print server, it is divided into the following sections: 1 Installation Problems 2 Intermittent Problems 3 Protocol-Specific Troubleshooting Installation problems If you can ...

  • Brother NC-5100H - page 119

    11 - 2 TROUBLESHOOTING YL4US_FAX2800MFC4800-FM5.5 2 If the configuration page prints but you cannot print documents, try the following a If you are using TCP/IP: Try pinging the print server from the host operating system command prompt with the command: ping ipaddress Where ipaddress is the print server IP address (note that in some instances it c ...

  • Brother NC-5100H - page 120

    TROUBLESHOOTING 11 - 3 YL4US_FAX2800MFC4800-FM5.5 3 If you cannot make any of the co nnections in step 2, check the following: a Make sure the printer is powered on and on-line. b Check the cabling, network connection, and print out a configuration page in the Networ k STATISTICS information to see if bytes are being transmitted and received. c Che ...

  • Brother NC-5100H - page 121

    11 - 4 TROUBLESHOOTING YL4US_FAX2800MFC4800-FM5.5 6 If the job exits the queue but does not print, make sure that you are not trying to print a text job to a PostScript printer. If you have a printer that is capable of automatic language switching, make sure that the printer is not forced into PostScript mode. Intermittent Problems If the print ser ...

  • Brother NC-5100H - page 122

    TROUBLESHOOTING 11 - 5 YL4US_FAX2800MFC4800-FM5.5 2 If you used BRCONFIG, NCP or to enter the IP address, make sure that you exited the remote console properly with a CTRL- D or EXIT and that you turned the printer off and then again (it may take up to two minutes for the IP address to take effect). 3 Make sure that the TCP/IP protocol of the print ...

  • Brother NC-5100H - page 123

    11 - 6 TROUBLESHOOTING YL4US_FAX2800MFC4800-FM5.5 3 If you are using a Berkeley-based UNIX, make sure that the daemon is started on Berkeley based systems with the command lpc start printer, where pr inter is the name of the local print queue. 4 If you are using an AT&T-based UNIX , make sure the printer is enabled (enable printer, where printe ...

  • Brother NC-5100H - page 124

    TROUBLESHOOTING 11 - 7 YL4US_FAX2800MFC4800-FM5.5 Windows ® NT/LAN Server (TCP/IP) Troubleshooting If you are having trouble printing with Windows ® NT or LAN Server, check the following: 1 Make sure that TCP/IP and TCP/IP print service are installed and running on the Windows ® NT system or the LAN Server file server. 2 If you are using DHCP an ...

  • Brother NC-5100H - page 125

    11 - 8 TROUBLESHOOTING YL4US_FAX2800MFC4800-FM5.5 Windows ® 95/98/Me Peer-to-Peer (HP JetAdmin compatible method) Troubleshooting If you are having trouble printing on a Windows ® 95/98/Me Peer-to- Peer network, check the follow ing (HP JetAdmin compatible method): 1 If the print server does not show up under JetAdmin on a Windows ® 95/98/Me Pee ...

  • Brother NC-5100H - page 126

    TROUBLESHOOTING 11 - 9 YL4US_FAX2800MFC4800-FM5.5 Brother Internet Print (TCP/IP) Troubleshooting 1 The first step in troubleshooting is to make sure that you have a valid E-mail connection on both the sending PC and the receiving print server. Try sending an E-mail message from the PC to a user at the remote site who can receive mail via the POP3 ...

  • Brother NC-5100H - page 127

    11 - 10 TROUBLESHOOTING YL4US_FAX2800MFC4800-FM5.5 Get More Info option in Windows ® 2000 not working If you are using a URL of: http://ip_address:631 or http://ip_address:631/ipp , the Get More Info option in Windows ® 2000 will not function. If you wish to use the Get More Info option use the following URL: http://ip_address This will then forc ...

  • Brother NC-5100H - page 128

    TROUBLESHOOTING 11 - 11 YL4US_FAX2800MFC4800-FM5.5 1 If you changed the login password, you must change the password in both the Brother print server (using the SET NETWARE PASSWORD command if you are using the BRConfig software) or by using a web br owser or the BRAdmin application and in the file server (using the PCONSOLE Print Server Informatio ...

  • Brother NC-5100H - page 129

    11 - 12 TROUBLESHOOTING YL4US_FAX2800MFC4800-FM5.5 3 If you have a large network, make sure that you have the Laser Writer V8.xx or equivalent driver, since earlier versions may cause PostScript errors. Also, verify that you get the correct printer information when you select Printer Info from the Setup button in the Chooser. 4 Make sure that you h ...

  • Brother NC-5100H - page 130

    A - 1 APPENDIX A YL4US_FAX2800MFC4800-FM5.5 A Appendix Appendix A General Information You can change the configuration of your print server using any of the following methods. • Brother BRAdmin application for Windo ws ® 95/98/Me, Windows NT ® 4.0 and Windows ® 2000/XP • Brother Web BRAdmin application for IIS * • HTTP (using a web browser ...

  • Brother NC-5100H - page 131

    A - 2 APPENDIX YL4US_FAX2800MFC4800-FM5.5 HTTP (Recommended) Use your favorite web browser to connect to the Brother print server. This will allow you to configure printer and/or print server parameters. WebJetAdmin Brother's print server range is HP WebJetAdmin compatible. TELNET To connect to the print server using TELNET on UNIX, Windows NT ...

  • Brother NC-5100H - page 132

    APPENDIX A - 3 YL4US_FAX2800MFC4800-FM5.5 Using Services General A service is a resource that can be accessed by computers that wish to print to the Brother print server . The Brother print server provides the following predefined services (do a SHOW SERVICE command in the Brother print server remote console to see a list of available services): En ...

  • Brother NC-5100H - page 133

    A - 4 APPENDIX YL4US_FAX2800MFC4800-FM5.5 Reloading the Print Server Firmware General The firmware on the print server is stored in flash memory. This means that you can upgrade the firmware by downloading the appropriate update file. To get the latest firmware update, visit the Brother Solutions web site at http://solutions.brother.com/ Because of ...

  • Brother NC-5100H - page 134

    APPENDIX A - 5 YL4US_FAX2800MFC4800-FM5.5 Reloading firmware using BRAdmin The BRAdmin application can be used to easily re-program your Brother print server. 1 Start BRAdmin. 2 Highlight the appropriate print server. Then press select the Control menu and choose Load Firmwa re. You can select more than one print server by pressing CTRL+<select& ...

  • Brother NC-5100H - page 135

    A - 6 APPENDIX YL4US_FAX2800MFC4800-FM5.5 Reloading process The Data LED on the printer control panel will blink during the firmware file loading process. During programming process, the backlight on the printer’s LCD goes off, and Erase xxxxxx and Write xxxxxx will be indicated alternately on the LCD. After the firmware update is completed, the ...

  • Brother NC-5100H - page 136

    APPENDIX A - 7 YL4US_FAX2800MFC4800-FM5.5 Reloading using the FTP Protocol from a command prompt By specifying the print server PASSWORD AS THE USERNAME when logging on, it becom es possible to upgrade the firmware of the print server or printer (if supported). The following example assumes that the print server password is " cambridge " ...

  • Brother NC-5100H - page 137

    A - 8 APPENDIX YL4US_FAX2800MFC4800-FM5.5 Reloading using the FTP Protocol from a Web Browser Please visit the Brother Solutions Web site at http://solutions.brother.com for more information on upgrading th e print serve r using a we b browser. ...

  • Brother NC-5100H - page 138

    INDEX I - 1 HL7050_US_NUG.FM5.5 I INDEX A AIX ...................................... 1-3 AIX 4.0 ................................ 1-8 AppleTalk ....... 7-1 , 7-3 , 7-8 , 11-2 , 11-11 ARP ...................1-2 , 10-1 , 10-6 B Berkeley UNIX .................... 1-1 BINARY_P1 ......... 1-2 , 1-3 , A-3 BINDERY ............................ 6-2 BIP .... ...

  • Brother NC-5100H - page 139

    I - 2 INDEX HL7050_US_NUG.FM5.5 Microsoft Internet Print Services ................................... 2-2 , 3-2 Microsoft TCP/IP printing ... 2-1 MIME .................................. 5-2 N NDPS .......................... 6-2 , 6-3 NDS .................................... 6-2 NET USE ............................ 4-9 NetBIOS ............. 4-1 , 4- ...

  • Brother NC-5100H - page 140

    INDEX I - 3 HL7050_US_NUG.FM5.5 Windows 2000 ......................... ......... 2-1 , 3-2 , 5-1 , 8-1 , 11-10 Windows 2000 Printing ................................... 2-2 , 2-5 Windows 95/98/Me ............. 3-1 Windows NT ........................ 8-1 Windows NT 3.51 ................ 2-1 Windows NT 3.5x ................ 2-1 Windows NT 3.5x Printi ...

Manufacturer Brother Category Printer

Documents that we receive from a manufacturer of a Brother NC-5100H can be divided into several groups. They are, among others:
- Brother technical drawings
- NC-5100H manuals
- Brother product data sheets
- information booklets
- or energy labels Brother NC-5100H
All of them are important, but the most important information from the point of view of use of the device are in the user manual Brother NC-5100H.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Brother NC-5100H, service manual, brief instructions and user manuals Brother NC-5100H. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Brother NC-5100H.

Similar manuals

A complete manual for the device Brother NC-5100H, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Brother NC-5100H by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Brother NC-5100H.

A complete Brother manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Brother NC-5100H - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Brother NC-5100H, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Brother NC-5100H, that we can find in the current document
3. Tips how to use the basic functions of the device Brother NC-5100H - which should help us in our first steps of using Brother NC-5100H
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Brother NC-5100H
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Brother NC-5100H in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Brother NC-5100H?

Use the form below

If you did not solve your problem by using a manual Brother NC-5100H, ask a question using the form below. If a user had a similar problem with Brother NC-5100H it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)