English dropdown-ico

Manual Sears 113.235501

22 pages 2.17 mb
Download

Go to site of 22

Summary
  • Sears 113.235501 - page 1

    Future Reference Serial Number Model and serial number may be found attached to the right side of housing. You should record both model and serial number in a safe place for future use. FOR YOUR SAFETY: READ ALL INSTRUCTIONS CAREFULLY , S/CRRFT3M SCROLL • assembly o operati . repair parts Sears, Roebuck and Co., Hoffman Estates, ILo 60179 U.S.A. ...

  • Sears 113.235501 - page 2

    i i_i FULL ON E YEAR WARRAN _ ON CRAFTSMAN SCROLL SAW If within Oneye&_from the date of purchase this craftsman SCroll Saw fails due to a defect in material or wo rk- • manship, Sears will repair it free of charge. WARRANTY SERVICE IS AVAILABLE BY SIMPLY RETURNING THE CRAFTSMAN SCROLL SAW TO THE NEAREST SEARS RETAIL/CATALOG STORE OR SERVICE C ...

  • Sears 113.235501 - page 3

    L CHECK DAMAGED PARTS. Check for: • Alignment of moving pads. . Binding of moving parts . Broken parts. o Stable mounting. . Any other conditions that may affect the way the saw works. If any part is missing, bent or broken in any way, or any electrical parts don't work properly, turn the saw off and unp]ug the saw REPLACE damaged, missing o ...

  • Sears 113.235501 - page 4

    :tions for scroll saw . cauS- - Unplugthe saw. ....... Wait for a mov ng Pads to stop • : L_UT onlyone worKplece aT a [tme - -' • Clear eveL=hin exce t the work iece and e ° " • Wt!] afa[badescrewdriver" -- turn motor shaft by hand ry_ g p p r aTee support dev ces off the table before turn ng the saw on. by i, nsertlng into th ...

  • Sears 113.235501 - page 5

    motor specifications and eUectricaB requirements This machine is equipped with, a 1725 RPM motor. It is wired for operation on 120V, 60Hz, alternating current. For replacement motor, refer to parts list in this manual. CONNECTING TO POWER SUPPLY OUTLET If power cord is worn or cut, or damaged in any way, have it replaced immediately. WARNING: If no ...

  • Sears 113.235501 - page 6

    , edge of the workpiece the blade firsti s or woodworking m 5. Blade Tooth Set - the distance that the edge of the sawblade tooth is bent (or set) outward from the side of the blade, 3, Sawblade Path - the area of the workpiece directly in line with and moving toward the sawblade edge. 4. Bevel - the ability to slant the table to make angle cuts. A ...

  • Sears 113.235501 - page 7

    DO NOT LIFT SAW BY THIS ARM LIFT HERE LIFT HERE assembay WARNING: For your own safety, never connect plug to power source outlet until all assembly steps are complete, and you have read and understand the safety and operating instructions. 1, Lift the saw by the frame and base and place scroll saw on work bench 2. Familiarize yourself with the cont ...

  • Sears 113.235501 - page 8

    fOr bevel: cutting up to 45 ° from the 0 ° or hor zontal cuttng positioni 2. A bevel scale is provided under the work table as a bonvenient reference for setting the approximate :table angle for bevel cutling. When greater precision is required, make practice cuts and adjust the table as necessary for your ;requirementS: :: ! : BEVEL SCALE :TO AL ...

  • Sears 113.235501 - page 9

    2. Use a small square to set the table at 90 ° to the blade. I! there is too much space between the square and the blade, the table must be adjusted. 3. When the space between the square and the blade is minimal, tighten the bevel lock knob, The table should now be approximately 90 ° to the blade. r- 4. Loosen the screw holding the bevel scale po ...

  • Sears 113.235501 - page 10

    removing and instaUling bRades WARNING: TO avoid Injury front accidental Starting, always turn switch OFF and remove switch key before removing or replacing the blade. _ TENSION KNOB 1: Loosen tension on blade by turning tension knob counterclockwise ( _ ) about three full turns. 2. Remove blade by pulling forward on blade and then lifting the blad ...

  • Sears 113.235501 - page 11

    4. Locate the blade guard and carefully install it onto the saw as shown. Lightly spread apart the blade guard so pins will go into holes in frame, 5. In order to cut, and to avoid uncontrollable lifting of the workpiece, the teeth of the blades used on the scroll saw should always point downward when installed on the scroll saw. 6. Install the bla ...

  • Sears 113.235501 - page 12

    :_Ountinq the SCroll sawto a bench :i 'WSed mounting this Saw to aworkbench a Solid :i ; : =. : I"- ..... : i:sUpptied with the s_wi:RoWever welrecommend the Descripiion : : :::: Qtyl ......... _.............. -_.... " He× Head Screw, 1!4-20 x length required ............. 3 / Flat Washers, !14 t.D .................................. ...

  • Sears 113.235501 - page 13

    getting to know your scro U saw 1. TENSION 2, BLADE HOLDER 3. BLADE GUARD ELOCK KNOB 7. BEVEL SCALE" _. TENSION KNOB _. Tightening the knob _cIockwise) will increase the tension of the blade. Loosening it (counterclockwise) will decrease the tension. 2. BLADE HOLDER ... Retain and position the blade. 3. BLADE GUARD .., Provides added control o ...

  • Sears 113.235501 - page 14

    gett ng to know your scroll saw 2 TO turn machine ON, place finger under switch lever and PULL end of switch, out, : i 3. To turn machine "OFF", PUSH lever =n. Never leave the machine unattended until it has come to a stop. PUSH 4. To lock switch in "OFF" position, hold switch IN with one hand, REMOVE key with other hand. WARNIN ...

  • Sears 113.235501 - page 15

    operation of your scroll saw PLEASE, road and understand the following items about your scroll saw before attempting to use the saw. 1. The saw does not cut wood by itself. You allow the saw to cut wood by guiding the wood into the blade as it moves. 2, The blade teeth cut wood _ on the down stroke, 3. You must guide the wood into the blade slowly ...

  • Sears 113.235501 - page 16

    • Do not wear loose clothing, gloves, neckties or jewelry (rings, wristwatches). They can get caught and draw you into moving parts. • :To avoid aocidental blade contact, minimize blade ° i breakage and provide maximum blade support = Wear non-slip footwear. always adjust the blade hold down and blade guard o T e back long hair. just €lear t ...

  • Sears 113.235501 - page 17

    _ON'T OVERREACH. Keep good footing and balance. .(eep your face and body to one side of blade, out of line with a possible thrown piece if the blade should break. WHENEVER SAW IS RUNNHNG WARNING: Don't let familiarity (gained from frequent use of your saw) cause a careless mistake. A careless fraction of a second is enough to cause a seve ...

  • Sears 113.235501 - page 18

    maintenance _WARNING: for your own safety, turn switch "OFF", I remove key and removeplug from power source I outlet before maintaining or lubricating your saw. GENERAL: An Occasional coat of paste wax on trhe work table will allow the wood being cut to glide smoothly across the work surface. MOTOR If the power cord is worn, cut or damage ...

  • Sears 113.235501 - page 19

    Sears recommends the following accessories 4em Sears Number Sears may recommend other accessories not listed in Leg Set ............................................................... 9-22244 manual. See your nearest Sears store for other accesso- ries. Blades ... See Catalog - For 5" long, Pin end type blades Plain End Blade Adaptor ......... ...

  • Sears 113.235501 - page 20

    "1'1 44 40" 35 35 32 36 22 23 24 22 22 7_ 6 / 12 22 2 _ if) -4 0 o_ m r'- =9 m 0 0 r= ...

  • Sears 113.235501 - page 21

    'ARTS LIST FOR CRAFTSMAN 16-INCH MOTOI_IZED SCROLL SAW MODEL NO. 113=235501 FIGURE 1 Always Order By Part Number-Not By Key Number ho Key No. Part No. 1 821526 2 821447-t 3 821416 4 821517 5 508855 6 821529 7 821530 8 STD541411 9 821531 10 66071 11 822033-t 12 821451 13 821463 14 STD551010 15 STD551210 16 808277q3 17 822220 18 821511 19 9-2225 ...

  • Sears 113.235501 - page 22

    f lllll_l,,ll i i MODEL NO. 113.235501 The model number of your scroll saw will be found attached to the right side of arm housing. When requesting service or ordering parts, always provide the following information: • Product Type • Modet Number • Part Number ° Part Description 1 CH SCROLL For the repair or replacement parts you need Call 7 ...

Manufacturer Sears Category Saw

Documents that we receive from a manufacturer of a Sears 113.235501 can be divided into several groups. They are, among others:
- Sears technical drawings
- 113.235501 manuals
- Sears product data sheets
- information booklets
- or energy labels Sears 113.235501
All of them are important, but the most important information from the point of view of use of the device are in the user manual Sears 113.235501.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Sears 113.235501, service manual, brief instructions and user manuals Sears 113.235501. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Sears 113.235501.

Similar manuals

A complete manual for the device Sears 113.235501, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Sears 113.235501 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Sears 113.235501.

A complete Sears manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Sears 113.235501 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Sears 113.235501, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Sears 113.235501, that we can find in the current document
3. Tips how to use the basic functions of the device Sears 113.235501 - which should help us in our first steps of using Sears 113.235501
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Sears 113.235501
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Sears 113.235501 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Sears 113.235501?

Use the form below

If you did not solve your problem by using a manual Sears 113.235501, ask a question using the form below. If a user had a similar problem with Sears 113.235501 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)