English dropdown-ico

Manual GE JTP20

16 pages 0.77 mb
Download

Go to site of 16

Summary
  • GE JTP20 - page 1

    1 30 ” Built-In W all Oven Installation Instructions JTP20, JTP25, JTP28, JTP48, JTP50, JT912, JT915, JT952, JT955, ZET938, ZET958 If you have questions, call 1.800.GE.CARES or visit our website at: ge.com Before Y ou Begin Read these instructions carefully and completely . • IMPORT ANT —Save these instructions for local inspector ’ s use. ...

  • GE JTP20 - page 2

    2 Electrical Requirements This appliance must be supplied with the proper voltage and frequency , and connected to an individual, properly grounded branch circuit, protected by a circuit breaker or fuse having amperage as noted on rating plate. (Rating plate is located on oven frame.) Rating Plate Location (behind oven door) IMPORT ANT SAFETY INSTR ...

  • GE JTP20 - page 3

    3 Open oven door and remove literature pack, broiler pan and grid, and oven racks. Remove Installation Instructions from literature pack and read them carefully before you begin. Be sure to place all literature, Owner ’s Manual, Installations, etc. in a safe place for future reference. Remove packaging materials. Check behind hinges and under fal ...

  • GE JTP20 - page 4

    4 Place the oven on a table or platform even with the cutout opening. (Platform must support 150 lbs. single, 275 lbs. double.) Installation Instructions Pre-Installation Checklist cont. Remove the bottom trim from the top of the oven. It will be installed at the end of the installation process. The trim is wrapped separately and taped to the top o ...

  • GE JTP20 - page 5

    5 Cabinet Width 30 ” Recommended Minimum Cutout Location from Floor 32 1/2 ” Cutout Depth 23 1/2 ” Min. Cutout Width 28 1/2 ” Min. 28 5/8 ” Max. Cutout Height 27 1/4 ” Min. 27 5/16 ” Max. If the cabinet does not have a solid bottom, two braces or runners must be installed level with the bottom of the cutout to support the weight of th ...

  • GE JTP20 - page 6

    6 Installation Instructions Cabinet Width 30 ” Recommended Minimum Cutout Location from Floor 12 ” Cutout Depth 23 1/2 ” Min. Cutout Width 28 1/2 ” Min. 28 5/8 ” Max. Cutout Height 51 13/16 ” Min. 51 15/16 ” Max. f the cabinet does not have a solid bottom, two braces or runners must be installed level with the bottom of the cutout to ...

  • GE JTP20 - page 7

    7 Installation Instructions Cutout for Single Built-In Oven Under Counter NOTE: This oven is not approved to be installed under a solid disk, induction or downdraft modular cooktop. A3 25" Gas or electric cooktops may be installed over this oven. See cooktop installation instructions for cutout size. See label on top of oven for approved cookt ...

  • GE JTP20 - page 8

    8 (Continued on following page) Installation Instructions Electrical Connections ATTENTION INST ALLER All electric wall ovens must be hard wired (direct wired) into an approved junction box. A plug and receptacle is NOT permitted on these products. DO NOT shorten the flexible conduit. The conduit strain relief clamp must be securely attached to the ...

  • GE JTP20 - page 9

    9 Installation Instructions Electrical Connections cont. B4 Three-Conductor Branch Circuit Connection When connecting to a three-conductor branch circuit, if local codes permit: a. Connect the bare oven ground conductor with the crimped neutral (white) lead to the branch circuit neutral (white or gray in color), using a wire nut. b . Connect the ov ...

  • GE JTP20 - page 10

    10 (Continued on following page) W ARNING: Mounting screws must be used. Failure to do so could result in the oven falling out of the cabinet causing serious injury . Installation Instructions Securing the Oven in the Opening Drilling the Pilot Holes and Mounting the Oven a. Drill through the mounting holes (top and bottom) of the side trim, for th ...

  • GE JTP20 - page 11

    11 a. With oven installed, take the bottom trim and center it on the bottom front edge of the cabinet opening. b. Using the trim as a template, mark the center of each slot (two total) where the mounting holes will be drilled. c. Remove the trim. d. Drill pilot holes into the center of each template mark. Installation Instructions Installing the Me ...

  • GE JTP20 - page 12

    12 Lift the oven door by placing one hand on each side. The door is heavy , so you may need help. Do not lift the door by the handle. With the door at the same angle as the removal position (half way between the closed and broil stop position, seat the notch of the hinge arm into the bottom edge of the hinge slot. The notch of the hinge arm must be ...

  • GE JTP20 - page 13

    13 Installation Instructions Remove all protective film, if present, and any stickers. Check to be sure that all wiring is secure and not pinched or in contact with moving parts. Pre-T est Checklist Check that the bottom trim is installed properly (see page 1 1). Check to be sure the mounting screws are installed and flush with the side trim (see p ...

  • GE JTP20 - page 14

    14 NOTES ...

  • GE JTP20 - page 15

    15 NOTES ...

  • GE JTP20 - page 16

    16 NOTES ...

Manufacturer GE Category Oven

Documents that we receive from a manufacturer of a GE JTP20 can be divided into several groups. They are, among others:
- GE technical drawings
- JTP20 manuals
- GE product data sheets
- information booklets
- or energy labels GE JTP20
All of them are important, but the most important information from the point of view of use of the device are in the user manual GE JTP20.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals GE JTP20, service manual, brief instructions and user manuals GE JTP20. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product GE JTP20.

Similar manuals

A complete manual for the device GE JTP20, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use GE JTP20 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of GE JTP20.

A complete GE manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual GE JTP20 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the GE JTP20, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the GE JTP20, that we can find in the current document
3. Tips how to use the basic functions of the device GE JTP20 - which should help us in our first steps of using GE JTP20
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with GE JTP20
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of GE JTP20 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning GE JTP20?

Use the form below

If you did not solve your problem by using a manual GE JTP20, ask a question using the form below. If a user had a similar problem with GE JTP20 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)