English dropdown-ico

Manual GE ZET2

16 pages 0.66 mb
Download

Go to site of 16

Summary
  • GE ZET2 - page 1

    1 30 ” Built-In W all Oven Installation Instructions ZET1, ZET2 If you have questions, call 1.800.GE.CARES or visit our website at: ge.com Before Y ou Begin Read these instructions carefully and completely . • IMPORT ANT —Save these instructions for local inspector ’ s use. • IMPORT ANT —Observe all governing codes and ordinances. • N ...

  • GE ZET2 - page 2

    2 IMPORT ANT SAFETY INSTRUCTIONS Installation Instructions For Y our Safety • Be sure your oven is installed properly by a qualified installer or service technician. • Be sure the oven is securely installed in a cabinet that is firmly attached to the house structure. Weight on the oven door could cause the oven to tip and result in injury . Nev ...

  • GE ZET2 - page 3

    3 Open oven door and remove literature pack, broiler pan and grid, oven racks, rack supports and a bag with 9 hex nuts. Read Installation Instructions carefully before you begin. Be sure to place all literature, Owner ’s Manual, Installations, etc. in a safe place for future reference. Remove packaging materials. Check behind hinges and under fal ...

  • GE ZET2 - page 4

    4 Place the oven on a table or platform even with the cutout opening. (Platform must support 175 lbs. [79 kg] single, 350 lbs. [159 kg] double.) Installation Instructions Pre-Installation Checklist cont. Remove the bottom trim from the top of the oven. It will be installed at the end of the installation process. The trim is wrapped separately and t ...

  • GE ZET2 - page 5

    5 Cabinet Width 30 ” (76.2 cm) Recommended Minimum Cutout Location from Floor 32 1/2 ” (82.6 cm) Cutout Depth 23 1/2 ” (59.7 cm) Min. Cutout Width 28 1/2 ” (72.4 cm) Min. 28 5/8 ” (72.7 cm) Max. Cutout Height 27 1/4 ” (69.2 cm) Min. 27 5/16 ” (69.2 cm) Max. If the cabinet does not have a solid bottom, two braces or runners must be ins ...

  • GE ZET2 - page 6

    6 Installation Instructions Cabinet Width 30 ” (76.2 cm) Recommended Minimum Cutout Location from Floor 12 ” (30.5 cm) Cutout Depth 23 1/2 ” (59.7 cm) Min. Cutout Width 28 1/2 ” (72.4 cm) Min. 28 5/8 ” (72.7 cm) Max. Cutout Height 51 13/16 ” (131.6 cm) Min. 51 15/16 ” (131.8 cm) Max. If the cabinet does not have a solid bottom, two br ...

  • GE ZET2 - page 7

    7 Installation Instructions Cutout for Single Built-In Oven Under Counter A3 25" Gas or electric cooktops may be installed over this oven. See cooktop installation instructions for cutout size. See label on top of oven for approved cooktop models. Gas and electrical connections for 30" gas cooktop must be located in an adjacent accessible ...

  • GE ZET2 - page 8

    8 Cabinetry NOTE: Additional clearances between cutouts may be required. Check to be sure the oven supports above the W arming Drawer location do not obstruct the required interior 23 1/2 ” (59.7 cm) depth and 9 1/4 ” (23.5 cm) height. • These Monogram Ovens require 3/4 ” (1.9 cm) overlap on both sides. Allow 1 ” (2.5 cm) Min. for top ove ...

  • GE ZET2 - page 9

    9 NOTE: The middle rail separating the two openings may need to be larger than the 2 ” (5.1 cm) minimum shown. Always refer to the individual installation instructions packed with each product for specific requirements. Combined Advantium and W all Oven Installation: When installed in combination with a Monogram single wall oven, use separate ele ...

  • GE ZET2 - page 10

    10 (Continued on following page) Installation Instructions Electrical Connections ATTENTION INST ALLER All electric wall ovens must be hard wired (direct wired) into an approved junction box. A plug and receptacle is NOT permitted on these products. DO NOT shorten the flexible conduit. The conduit strain relief clamp must be securely attached to th ...

  • GE ZET2 - page 11

    11 Installation Instructions Electrical Connections cont. B6 Three-Conductor Branch Circuit Connection When connecting to a three-conductor branch circuit, if local codes permit: a. Connect the bare oven ground conductor with the crimped neutral (white) lead to the branch circuit neutral (white or gray in color), using a wire nut. b. Connect the ov ...

  • GE ZET2 - page 12

    12 (Continued on following page) W ARNING: Mounting screws must be used. Failure to do so could result in the oven falling out of the cabinet causing serious injury . Installation Instructions Securing the Oven in the Opening Drilling the Pilot Holes and Mounting the Oven a. Drill through the mounting holes (top and bottom) of the side trim, for th ...

  • GE ZET2 - page 13

    13 Installation Instructions Installing the Metal Bottom T rim IMPORT ANT : If this unit is ever removed from the cabinet or the oven is ever pulled out for service, the trim must be removed first or damage to the trim will occur . C4 a. Place the bottom trim between the side trim and against the bottom of the cutout. b. Using two trim screws provi ...

  • GE ZET2 - page 14

    14 Lift the oven door by placing one hand on each side. The door is heavy , so you may need help. Do not lift the door by the handle. With the door at the same angle as the removal position, seat the notch of the hinge arm into the bottom edge of the hinge slot. The notch of the hinge arm must be fully seated into the bottom of the slot. Open the o ...

  • GE ZET2 - page 15

    15 Installation Instructions Remove all protective film, if present, and any stickers. Check to be sure that all wiring is secure and not pinched or in contact with moving parts. NOTE T O ELECTRICIAN: Y ou must unplug the green wire (near where the long flexible conduit exits the unit) when conducting high-potential testing. Please replug prior to ...

  • GE ZET2 - page 16

    16 Printed in U.S.A. ...

Manufacturer GE Category Computer Drive

Documents that we receive from a manufacturer of a GE ZET2 can be divided into several groups. They are, among others:
- GE technical drawings
- ZET2 manuals
- GE product data sheets
- information booklets
- or energy labels GE ZET2
All of them are important, but the most important information from the point of view of use of the device are in the user manual GE ZET2.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals GE ZET2, service manual, brief instructions and user manuals GE ZET2. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product GE ZET2.

Similar manuals

A complete manual for the device GE ZET2, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use GE ZET2 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of GE ZET2.

A complete GE manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual GE ZET2 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the GE ZET2, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the GE ZET2, that we can find in the current document
3. Tips how to use the basic functions of the device GE ZET2 - which should help us in our first steps of using GE ZET2
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with GE ZET2
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of GE ZET2 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning GE ZET2?

Use the form below

If you did not solve your problem by using a manual GE ZET2, ask a question using the form below. If a user had a similar problem with GE ZET2 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)