English dropdown-ico

Manual Agilent Technologies 87130A

140 pages 1.46 mb
Download

Go to site of 140

Summary
  • Agilent Technologies 87130A - page 1

    87130A Attenuator/Switch Driver Operating and Service Guide Manual par t number: 87 130-90007 Printed in USA August 2001 Supersede s: May 2000 ...

  • Agilent Technologies 87130A - page 2

    ii Agilent 87130A Operating and Service Manual Notice The infor mation containe d in this document is subject t o change wit hout notice. Agilent T echnologi es makes no warranty o f any kind with regard t o this materia l, including, but not li mited to, the implied war ranties of merchanta bility and fitness for a part icular pur pose. Agile nt T ...

  • Agilent Technologies 87130A - page 3

    Agilent 87130A Operating and Service Manual iii Wa r r a n t y Certific atio n Agilent T echnolog ies, Inc., certifies that thi s pr oduct met its p ublished spec ific atio ns a t the time of sh ipme nt from the fac tory . Ag ilent T ech nolo gie s further certif ies that its cali bration me asur ements ar e traceable to the United St ates Nati ona ...

  • Agilent Technologies 87130A - page 4

    iv Agilent 87130A Operating and Service Manual W ARRANTIES OR MERCHANT ABILITY AND FITNESS FOR A P AR TICULAR PURPOSE. EXCLUSIVE REMEDIES. THE REMEDIES PROVIDED HEREIN ARE BUYER ’ S SOLE AND EXCLUSIVE REMEDIES. AGILENT TECHNOLOGIES SHALL NOT BE LIABLE FOR ANY DIRECT , INDIRECT , SPECIAL, INCIDENT AL, OR CONSEQUENTIAL DAMAGES, WHETHER BASED ON CON ...

  • Agilent Technologies 87130A - page 5

    Agilent 87130A Operating and Service Manual v Service and Support Any adjust ment, mainte nance, or repa ir of th is product must be perfo rmed by quali fied pers onnel. Cont act your c ustomer engi neer thr ough your loca l Agilent T echnologi es Servi ce Center . Y ou can find a list o f local ser vice repres entatives on the W eb at: www.agilent ...

  • Agilent Technologies 87130A - page 6

    vi Agilent 87130A Operating and Service Manual Safety and Regulatory Infor mation Review this prod uct and re lated docu mentation to famili arize you rself wit h safety markings and inst ructions bef ore you ope rate the instrument. Thi s product has been des igned and t ested in accordanc e with int ernational standar ds. W ARNING The W ARNING no ...

  • Agilent Technologies 87130A - page 7

    Agilent 87130A Operating and Service Manual vii Safety Earth Ground This is a Safety Class I prod uct (prov ided with a pr otective earthing terminal ). An uninter ruptibl e safety ea rth ground must be provided fro m the main power s ource to the product input wiri ng terminal s, power cord, o r supplie d power cord set. Wheneve r it is likel y th ...

  • Agilent Technologies 87130A - page 8

    viii Agilent 87130A Operating and Service Manual General Safety Consi derations W ARNING • This product has b een designed and te sted in accordance with IEC Publication 1010, Safety Requireme nts for Electronic Meas uring Apparatus, and has been supplied in a safe condition. The instruction documentation co ntains information and w arnings which ...

  • Agilent Technologies 87130A - page 9

    Agilent 87130A Operating and Service Manual ix ...

  • Agilent Technologies 87130A - page 10

    x Agilent 87130A Operating and Service Manual T ypeface C onventions Itali cs • Used to emphasi ze importa nt infor mation: Use this software onl y with the 87130A. • Used for t he titl e of a publ ication : Refe r to t he Agilent 8713 0A Operating and Servic e Manual . • Used to ind ica te a v ari abl e: T ype LOAD BIN filen ame . Instrument ...

  • Agilent Technologies 87130A - page 11

    Contents Agilent 87130A Operating and Service Manual Contents-1 1. Introducing t he 87130A Atte nua tor /Sw itch Dr ive r Feature s of the Attenuat or/Switch Driver . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 Figur e 1-1. 87130A Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . 1- 2 Drive Pulse and Sensing . . . . . . . . . ...

  • Agilent Technologies 87130A - page 12

    Contents-2 Agilent 87130A Operating and Service Manual Figur e 2-7. Daisy Chain of Driver Ca r ds in Si ngle Enclo sur e . . . . 2-8 Figur e 2-8. Daisy Chain of Driver Ca r ds in Dif fer ent Enclosur es . 2-8 Connecting At tenuators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9 Figur e 2-9. T ypical Atten uator Cable s C ...

  • Agilent Technologies 87130A - page 13

    Agilent 87130A Operating and Service Manual Contents-3 *IDN (Identi fication Number) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-16 *OPC (Operation Compl ete) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4- 17 *RST (Reset ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Agilent Technologies 87130A - page 14

    Contents-4 Agilent 87130A Operating and Service Manual Figur e 4-1. T iming Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-77 5. Replaceable Pa rts Accessory Boar ds and Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-13 T able 5-1. Accesso ries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Agilent Technologies 87130A - page 15

    Agilent 87130A Operating and Service Manual 1-1 1 Intr oducing the 87130A Attenuator/Switch Driver Overview I n this cha pter you wi ll find: • Function , feature s, and capabil ities of t he 87130A att enuator/ switch drive r • How to unpac k and check y our instrument • How to set up a stat ic-f ree wo rk stat ion • How to cont act Agilen ...

  • Agilent Technologies 87130A - page 16

    1-2 Agilent 87130A Operating and Service Manual Introducing the 87130A Attenuator/Switch Driver Features of th e Attenuator/Switch Driver Features of the Attenuator/Swit ch Drive r The Agilen t 87130A att enuator/swi tch drive r is a GPIB compat ible instru ment design ed to driv e electr omechanical switches and step attenua tors. • The stand ar ...

  • Agilent Technologies 87130A - page 17

    Agilent 87130A Operating and Service Manual 1-3 Introducing the 87130A Attenuator/Switch Driver Features of t he Attenuator/Switch Driver Drive Puls e and Sensing The atte nuator/s witch dri ver can del iver 500 mA, 2 4 Vdc curren t pulses to 31 indivi dual swit ch secti ons and up t o a total of 248 swit ch sections by the additi on of exte rnal 8 ...

  • Agilent Technologies 87130A - page 18

    1-4 Agilent 87130A Operating and Service Manual Introducing the 87130A Attenuator/Switch Driver Features of th e Attenuator/Switch Driver Compa tible S witch es and Attenuators The atte nuator/ s witch dri ver is de signed to drive Agil ent switches and attenua tors shown in the ta bles belo w . NOTE If you ar e using s witches or at tenuator s mad ...

  • Agilent Technologies 87130A - page 19

    Agilent 87130A Operating and Service Manual 1-5 Introducing the 87130A Attenuator/Switch Driver Features of t he Attenuator/Switch Driver Front Panel Featur es The front panel LEDs i ndicate the status o f the 87130 A atten uator/switc h driver . The front -panel LEDs s hould turn on a nd of f while t he switch d river is perf orming the self-te st ...

  • Agilent Technologies 87130A - page 20

    1-6 Agilent 87130A Operating and Service Manual Introducing the 87130A Attenuator/Switch Driver Unpacking Your Instru ment Unpacking Y our Instrument Unpack and i nspect t he shippi ng contain er and it s contents thoroughl y to ensure t hat nothing was damaged duri ng shipment. If the shipping co ntainer or cushi oning materia l is damaged, t he c ...

  • Agilent Technologies 87130A - page 21

    Agilent 87130A Operating and Service Manual 1-7 Introducing the 87130A Attenuator/Switch Driver Unpacking Your Inst rument Figure 1-3 Packaging Mat erials for the 87130A Sw itch Driver Item Quantity Part Number Description 1 1 921 1- 6365 Outer carton 2 1 5181-5515 Foam In sert 3 Foam insert (Part of item 2.) 4 1 5181-5535 Spacer ...

  • Agilent Technologies 87130A - page 22

    1-8 Agilent 87130A Operating and Service Manual Introducing the 87130A Attenuator/Switch Driver Before Installing th e Attenuator/Switch Driver Befor e Installing the At tenuator/Switch Driver Electr ostatic dischar ge ( ESD) can d amage or d estroy e lectron ic componen ts. All work pe rformed on assemblies consist ing of ele ctronic compon ents s ...

  • Agilent Technologies 87130A - page 23

    Agilent 87130A Operating and Service Manual 1-9 Introducing the 87130A Attenuator/Switch Driver Before Installing t he Attenuator/Switch Driver Reducing ES D Damage T o help reduce the amount of ESD damage tha t occurs during ins tallation , testi ng, or serv icing ins truments u se the follo wing gui delines: • Be sure t hat all i nstruments a r ...

  • Agilent Technologies 87130A - page 24

    1-10 Agilent 87130A Operating and Service Manual Introducing the 87130A Attenuator/Switch Driver Returning Your Instrum ent for Service Returning Y our Instrument for Service T o obtain serv icing inf ormation o r to order r eplacement parts, co ntact your nearest Agilent T echnol ogies Servic e Center l isted under “ Service and Support ” on p ...

  • Agilent Technologies 87130A - page 25

    Agilent 87130A Operating and Service Manual 2-1 Installing the 87130A Attenuator/Switch Driver 2 Installing the 87130A Attenuator/Switch Driver Overview I n this cha pter you wi ll lear n about: • How to inst all your switch drive r • How to veri fy its ba sic func tionality • How to addre ss your inst rument • How to conne ct it to a switc ...

  • Agilent Technologies 87130A - page 26

    2-2 Agilent 87130A Operating and Service Manual Installing the 87130A Attenuator/Switch Driver Getting Start ed Gettin g Started Initi al Insp ecti on 1. Unpack and inspect the sh ipping cont ainer and it s content s thorough ly to ensure t hat nothing wa s damaged dur ing shipmen t. If the shi pping contain er or cush ioning material is damaged, t ...

  • Agilent Technologies 87130A - page 27

    Agilent 87130A Operating and Service Manual 2-3 Installing the 87130A Attenuator/Switch Driver Getting Started GPIB Addr essing 3. Use the f ive-bit binary add ress swit ches loca ted on the rear pane l of the instru ment to c hange the GPIB address. ❍ The 87130A has a factor y preset a ddress of 9. There are 32 po ssible address es. The sw itch ...

  • Agilent Technologies 87130A - page 28

    2-4 Agilent 87130A Operating and Service Manual Installing the 87130A Attenuator/Switch Driver Connecting Switch Dr ivers to Switches and Attenuator s Connecting Switc h Drivers to Swit ches and Attenuators Driver Boar ds The stand ard 87130A at tenuator /switch d river has a single interna l driver board capable of driv ing 31 switche s. The atten ...

  • Agilent Technologies 87130A - page 29

    Agilent 87130A Operating and Service Manual 2-5 Installing the 87130A Attenuator/Switch Driver Connecting Switch Drivers to Switches and Attenuato rs Using External Drivers A standard switc h driver can contr ol up to se ven extern al 84940A drive r car ds. ❍ Each dri ver card ha s 31 4-pin black out put connector s numbere d J1 to J31 ( silkscr ...

  • Agilent Technologies 87130A - page 30

    2-6 Agilent 87130A Operating and Service Manual Installing the 87130A Attenuator/Switch Driver Connecting Switch Dr ivers to Switches and Attenuator s CAUTION Do not c onnect or disconn ect rel ays from 84940A ext ernal driv er ca rds with prefix es prior to US4016 whil e the attenu ator/swi tch drive r line switc h is turned o n. An uninten tional ...

  • Agilent Technologies 87130A - page 31

    Agilent 87130A Operating and Service Manual 2-7 Installing the 87130A Attenuator/Switch Driver Connecting Switch Drivers to Switches and Attenuato rs W iring Channel Connector s When ins talling th e switch dr iver , it is impe rative t o know which wi res will cause an OPEN or CLOSE cond ition on e ach switch. • An OPEN condit ion is defin ed as ...

  • Agilent Technologies 87130A - page 32

    2-8 Agilent 87130A Operating and Service Manual Installing the 87130A Attenuator/Switch Driver Connecting Switch Dr ivers to Switches and Attenuator s Connecting Multiple Driver Cards The cards are numb ered from 1 to 8 ; the rel ays on eac h card are numbered from 0 to 30. E ach re lay is re ferr ed to a s a c han nel by the switc h d rive r . The ...

  • Agilent Technologies 87130A - page 33

    Agilent 87130A Operating and Service Manual 2-9 Installing the 87130A Attenuator/Switch Driver Connecting Switch Drivers to Switches and Attenuato rs Connecting Attenuators Connect a ttenuat or cable s using a V iking connector and a t en pin c onnector . A typical connecti on of four se ction att enuators is shown be low . When conn ecting at tenu ...

  • Agilent Technologies 87130A - page 34

    2-10 Agilent 87130A Operating and Service Manual Installing the 87130A Attenuator/Switch Driver Connecting Switch Dr ivers to Switches and Attenuator s Optimizing S witching Speed T o increase th e speed at which your sw itch matrix o perates, re fer to the tab le below to determine wh ich fou r relays, when connected , will be on the same drive l ...

  • Agilent Technologies 87130A - page 35

    Agilent 87130A Operating and Service Manual 2-11 Installing the 87130A Attenuator/Switch Driver Connecting Switch Drivers to Switches and Attenuato rs Driver Car d Address Set the 4- bit DIP switc h on the 84940A dri ver assembly ca rd to each add ress as sho wn in the figur e be low . (S 1 “ up ” is ope n or awa y fr om th e PC b oa rd.) Each ...

  • Agilent Technologies 87130A - page 36

    2-12 Agilent 87130A Operating and Service Manual Installing the 87130A Attenuator/Switch Driver Connecting Switch Dr ivers to Switches and Attenuator s 7061 1-6001 1, and 70612-6001 1 cables o f #28 A WG wire size , at a tot al cable le ngth of 32.8 fee t from the 87130 A would have a volta ge of 20.3 v olts availa ble at th e driver b oard. (21.5 ...

  • Agilent Technologies 87130A - page 37

    Agilent 87130A Operating and Service Manual 2-13 Installing the 87130A Attenuator/Switch Driver Connecting Switch Drivers to Switches and Attenuato rs Pin Functions for 36-Pin I/O Data Cable • The stand ard switc h driver has a high densi ty male, 36-pi n SCSI II t ype connecto r . • The stand ard I/O dat a cable is a five-f oot 28 A WG cable w ...

  • Agilent Technologies 87130A - page 38

    2-14 Agilent 87130A Operating and Service Manual Installing the 87130A Attenuator/Switch Driver Connecting Switch Dr ivers to Switches and Attenuator s Pin Function s for 68-pin Driver Output Connector • The 87130A ha s a rear -panel 68-pin c onnector for drivi ng attac hed switches . The standar d output cab le is a six- foot 28 A W G cable wit ...

  • Agilent Technologies 87130A - page 39

    Agilent 87130A Operating and Service Manual 3-1 3 Specifica tions Overview Pe rformance specific ations a re the per formance s tandards o r limits aga inst which the 87130A can be tested. The specifi cations are or ganized into two categor ies: • Measurement relate d specifi cations which des cribe warra nted performa nce for t he 87130A over th ...

  • Agilent Technologies 87130A - page 40

    3-2 Agilent 87130A Operating and Service Manual Specifications Performance Specif ications Performance Spe cifications T able 3-1 87130A Elec trical Sp ecificati ons 1. Refer to “ Compatible Switches and Attenua tors ” on page 1- 4 if you are usi ng switches or attenuators ma de by another c ompany . Electrical Specif ications Drive Capaci ty - ...

  • Agilent Technologies 87130A - page 41

    Agilent 87130A Operating and Service Manual 3-3 Specifications Performance Specificatio ns T able 3-2 87130A Envir onmental Spec ifications Environmental Speci fications T empe rature Operating 0 to + 55 ° C Non-operat ing − 40 to 70 ° C Humid ity Operating and Non-operat ing 80% relativ e humidity up to 31 ° C decreasing l inearly to 50% rela ...

  • Agilent Technologies 87130A - page 42

    3-4 Agilent 87130A Operating and Service Manual Specifications Performance Specif ications ...

  • Agilent Technologies 87130A - page 43

    Agilent 87130A Operating and Service Manual 4-1 4 Remote Operation Overview I n this cha pter you wi ll lear n about pro gramming the 87130A using a control ler: • How to set up t he switch drive r and start programming gr oups and pat hs for switche s • How to set switch del ay , pulse wi dth, and se nsing • How to sens e switch stat us • ...

  • Agilent Technologies 87130A - page 44

    4-2 Agilent 87130A Operating and Service Manual Remote Operation Progr ammi ng Pr ogramming Sta nda rd C omm a nds The instrumen t command lang uage is Standa rd Commands for Programmabl e Instru ments (SCPI) . The progr amming examples and infor mation in t his chapt er use the SCPI format. SCPI f ollows IEEE 4 88.2-1987 Code s, Formats, Prot ocol ...

  • Agilent Technologies 87130A - page 45

    Agilent 87130A Operating and Service Manual 4-3 Remote Operation Progra mming Syn tax Pr ogramming Syntax T alking to the Switch Driver In gener al, computer s acting as controll ers communic ate with t he switch driver by passin g messag es over a remote in terface using the I/O sta tements provided in the in struc tion set of the contr oller ’ ...

  • Agilent Technologies 87130A - page 46

    4-4 Agilent 87130A Operating and Service Manual Remote Operation Programm ing Syntax Addr essing the Swit ch Driver Since GPIB c an address multiple dev ices thr ough the sa me interf ace card, the devi ce selec tor passe d with the prog ram messa ge must include not only the corr ect int erface c ode, but al so the correc t instr ument addre ss. I ...

  • Agilent Technologies 87130A - page 47

    Agilent 87130A Operating and Service Manual 4-5 Remote Operation Progra mming Syn tax Commands A command is compose d of a head er , any a ssociated da ta, and a t erminator . The header is the mnemonic or mnemoni cs that repre sent the oper ation to be perfor med by the s witch driver . The diff erent t ypes of h eaders ar e discus sed in the f ol ...

  • Agilent Technologies 87130A - page 48

    4-6 Agilent 87130A Operating and Service Manual Remote Operation Programm ing Syntax Example *CLS is an example of a common command he ader . *CLS; ROUTE:DRIVE:ON (@100,102,104,106,....); Common commands use d by the swi tch driver a re explaine d in more det ail in the “ Common Command Referen ce ” later i n this ch apter . Program Header Opti ...

  • Agilent Technologies 87130A - page 49

    Agilent 87130A Operating and Service Manual 4-7 Remote Operation Progra mming Syn tax Character Program Data Characte r program data is used to convey par ameter infor mation as alph a or alphanumer ic stri ngs. Example ROUTE:VERIFY:ON:ALL The :VERIFY func tion is s pecifie d to be ON fo r ALL cha nne ls. Numeric Program Data Some command hea ders ...

  • Agilent Technologies 87130A - page 50

    4-8 Agilent 87130A Operating and Service Manual Remote Operation Programm ing Syntax Query commands are also used to get r esults of switch s tatus made by t he switc h d river, with the qu ery ac tua lly a ctiva ting the switc h. Example ROUTe:CLOSE? <channel spec> instru cts the dr iver to sense th e statu s of the s witch and pl ace the r ...

  • Agilent Technologies 87130A - page 51

    Agilent 87130A Operating and Service Manual 4-9 Remote Operation Programming th e Switch Driver Pr ogramming the Swi tch Driver Initi alizat ion T o make sure the bus and all appropri ate inte rfaces a re in a kno wn state, begin e ver y pr ogr am with a n i nit ializa tio n s tate men t. Example CLEAR 709 ! init iali zes the i nterf ace of th e dr ...

  • Agilent Technologies 87130A - page 52

    4-10 Agilent 87130A Operating and Service Manual Remote Operation Programming th e Switch Driver wher e GROU P1 represent s the name of th e desired gr oup. This would enter the current label of the group in the st ring vari able Set ting$. Example All r esults f or queries s ent in a p rogram messag e must be read b efore another program me ssage ...

  • Agilent Technologies 87130A - page 53

    Agilent 87130A Operating and Service Manual 4-11 Remote Operation Programming th e Switch Driver Stri ng V a riab les If you wan t to obser ve the header s for quer ies, you must bring the r eturned data in to a BASIC str ing variabl e. Reading qu eries in to string va riables is simp le a nd str aigh tforw ar d, r equir ing litt le at tentio n to ...

  • Agilent Technologies 87130A - page 54

    4-12 Agilent 87130A Operating and Service Manual Remote Operation Common Com mands Reference Common Commands Refer en ce The common commands us ed in this i nstrument a re shown in the fo llowing table . • The commo n commands con trol some of the b asic ins trument func tions, such as i nstrument identific ation and r eset and how st atus is rea ...

  • Agilent Technologies 87130A - page 55

    Agilent 87130A Operating and Service Manual 4-13 Remote Operation *CLS (Clear Status) *CLS (C lear Status) Synta x *CLS Description The *CLS (cl ear stat us) common command clears t he statu s data st ructures, includi ng the device defined e rror queu e. This command als o clears *OPC and *OPC?. If the *CLS command immed iately follows a PROGRAM M ...

  • Agilent Technologies 87130A - page 56

    4-14 Agilent 87130A Operating and Service Manual Remote Operation *ESE (Event Status Enable) *ESE (Event Status Enable) Synta x *ESE mask *ESE? Description The *ESE command sets the Standa rd Event St atus Enable Reg ister bi ts. This regist er contains a mask value for the b its to be ena bled in t he Standard Event Sta tus Register . A one in th ...

  • Agilent Technologies 87130A - page 57

    Agilent 87130A Operating and Service Manual 4-15 Remote Operation *ESR? (Event Status Regist er Query) *ESR? (Event S tatus Registe r Query) Synta x * ESR? Description The *ESR qu ery returns the conte nts of th e Standard Event Stat us Registe r . The tabl e shows each bit in th e Event Sta tus Regist er and th e bit weigh t. When you rea d the Ev ...

  • Agilent Technologies 87130A - page 58

    4-16 Agilent 87130A Operating and Service Manual Remote Operation *IDN (Identificat ion Number) *IDN (Ide ntification Number) Synta x * IDN? Description The *IDN qu ery allo ws the inst rument to identify itself . It retu rns a str ing such as: HEWLETT-PACKARD,87130A,US12345678,95071 3 Where 95071 3 is the firmware ve rsion numbe r and US 12345678 ...

  • Agilent Technologies 87130A - page 59

    Agilent 87130A Operating and Service Manual 4-17 Remote Operation *OPC (Ope ration Comple te) *OPC (O perat ion Com plete) Synta x *OPC *OPC? Description The *OPC and *OPC? commands are used to synchro nize remot e interface softwar e to inte rnal module events. • The *OPC (ope ration co mplete) co mmand will cause the instrument to set the opera ...

  • Agilent Technologies 87130A - page 60

    4-18 Agilent 87130A Operating and Service Manual Remote Operation *RST (Reset) *RST (R eset) Synta x *RST Description *RST is equi valent t o a power up c ondition for the swit ch hardware . All rel ays for which DRI VE is ON are s et to the position s determin ed by ROUTe:PFAil. For any rel ays no t in eith er th e ROUTe:PFAil:OPEN or ROUTe:PFAil: ...

  • Agilent Technologies 87130A - page 61

    Agilent 87130A Operating and Service Manual 4-19 Remote Operation *SRE (Request Enable) *SRE (R equest E nable) Synta x *SRE mask *SRE? Description The *SR E command sets the Service Request Enable Registe r bits. This wil l indicat e whether or not the device ha s at leas t one reas on for re questing servic e. A one in th e Service Request Enab l ...

  • Agilent Technologies 87130A - page 62

    4-20 Agilent 87130A Operating and Service Manual Remote Operation *STB (Statu s Byte) *STB (Sta tus Byt e) Synta x *STB? Description The *STB qu ery retu rns the cu rrent val ue of the instrument ’ s status byt e. Refer to the tabl e below for the de finitions of the bit s in the status by te. Example Query OUTPUT 709; “ *STB? ” ENTER 709;Val ...

  • Agilent Technologies 87130A - page 63

    Agilent 87130A Operating and Service Manual 4-21 Remote Operation *TST? (Te st) *TST? (T est) Synta x *TST? Description *TST? causes al l relays to cycle through bot h of thei r positions (first all the CLOSE paths a re set; the n all the OPEN paths), a nd then get placed in th e approp riate p ower up posi tions. Ref er to *RST (Reset) on pag e 4- ...

  • Agilent Technologies 87130A - page 64

    4-22 Agilent 87130A Operating and Service Manual Remote Operation *WAI *W AI Synta x *WAI Description The *WAI comman d ca use s the i nst rume nt to wa it for a ll pe nd ing G PIB operati ons to fi nish befo re pro cessing an y further co mmands. Example OUTPUT 709; “ *WAI ” ...

  • Agilent Technologies 87130A - page 65

    Agilent 87130A Operating and Service Manual 4-23 Remote Operation Hierarchy Hierar chy T able 4-6 Command T ree ROUTE :CLOSe :OPEN :PATH :DEFine :CATalog :LABel :VALue :DELete :ALL :GROUP :NAME :CATalog :ADD :REMove :DEFine? :LABel :AUTOselect :ON :OFF :DELete :DELete :ALL ...

  • Agilent Technologies 87130A - page 66

    4-24 Agilent 87130A Operating and Service Manual Remote Operation Hierarchy T able 6-6. Command T r ee (conti nued ) ROUTE :PFAil :CLOSe :OPEN :DELete :VERify :ON :OFF :ALL :DRIVe :ON :OFF :ALL :WIDth :DELay :SERialnumber[?] :MODelnumber[?] :EEROM :CYCles? ...

  • Agilent Technologies 87130A - page 67

    Agilent 87130A Operating and Service Manual 4-25 Remote Operation Hierarchy T able 6-6. Command T r ee (conti nued) NOTE A colon ( : ) must be u sed in front of the ROUTE , DIAGnostics , MEMory , etc. commands if that command is not the fi rst it em in a com mand string . (The colon is optio nal if the c ommand is t he firs t in the s tring.) MEMor ...

  • Agilent Technologies 87130A - page 68

    4-26 Agilent 87130A Operating and Service Manual Remote Operation SCPI C omm and Re fer ence SCPI Command Refer ence Channel List s The 87130A can co ntrol up to s even dif f erent e xternal driver ca rds, each o f which can drive up t o 31 dif ferent relays. The c ards are numbered fr om 1 to 8; the r elays on each card are numbered fr om 0 to 30. ...

  • Agilent Technologies 87130A - page 69

    Agilent 87130A Operating and Service Manual 4-27 Remote Operation :ADD :ADD Synta x ROUTE:GROUP:ADD <group name>,<path name > Description This command adds an exist ing path to t he end of an existing gr oup. The group name a nd path name must have bee n previously defined us ing GROUP:NAME and PATH:DEF. A path may be added to a group i ...

  • Agilent Technologies 87130A - page 70

    4-28 Agilent 87130A Operating and Service Manual Remote Operation :AUTOselect :AUTOselect Synta x ROUTe:GROUP:AUTOselect[?] < group name > Description This tur ns the cur rent Auto Select st ate for the group o n or of f. Example Command ROUTE:GROUP:AUTO:ON ATTEN; This turns the current Auto Select state for the group ATTEN on. ROUTE:GROUP:AU ...

  • Agilent Technologies 87130A - page 71

    Agilent 87130A Operating and Service Manual 4-29 Remote Operation :CAT al og? :CA T alog? Synta x ROUTe :CATALOG? Description Returns a list of groups (u p to 16) or all defined paths in t he module. Example Query ROUTE:GROUP:CATALOG? This quer y returns a list of a ll of th e group names , in order from 1 to 16, separat ed by commas. ROUTE:PATH:CA ...

  • Agilent Technologies 87130A - page 72

    4-30 Agilent 87130A Operating and Service Manual Remote Operation :CLOSe :CLOSe Synta x ROUTe:CLOSe ROUTe:PFail:CLOSe[?] Description Each chann el has a CLOSE o r OPEN position. On Agilent r elays, the CLOSE path is the pa th between the input terminal labeled 2 on the rel ay and the input terminal labele d C. It is rec ognized that CLOSE a nd OPEN ...

  • Agilent Technologies 87130A - page 73

    Agilent 87130A Operating and Service Manual 4-31 Remote Operation :CLOSe Example Command ROUTE:CLOSE ATTEN_14; Sending t he above comman d causes the s et of swit ch OPENs and CLOSEs defined by the PATH (r efer to :P A TH on page 4-55 ) with name ATTEN_14 to be execut ed. The fir st group of s witch set tings in the PATH is in terpr ete d as CLOSE ...

  • Agilent Technologies 87130A - page 74

    4-32 Agilent 87130A Operating and Service Manual Remote Operation :CLOSe Example Query ROUTE:PFAIL:CLOSE? (@1 01,205); The incl usion of a question ma rk causes a readback of the power up state of the requ ested cha nnels as a li st of 1 ’ s and 0 ’ s separated by co mmas. A 1 mean s the chan nel is in t he PFA:CLOS list. A 0 means tha t it is ...

  • Agilent Technologies 87130A - page 75

    Agilent 87130A Operating and Service Manual 4-33 Remote Operation :CYCLes? :CYCLes? Synta x DIAGnostics:EERom:CYCLes? Description This query ca uses the 87130A to rea d back the number of ti mes to which the EEROM has been wr itten. If t his number e xceeds 10,000 t he EEROM should be replaced . If the EEROM ha s never been wri tten to , then 0 is ...

  • Agilent Technologies 87130A - page 76

    4-34 Agilent 87130A Operating and Service Manual Remote Operation :DEFine :DEFine Synta x ROUTe:PATH:DEFine <path name>,<channel list> [,<channel list>] ROUTe:GROUP:DEFine? <group name> ROUTe:PATH:DEFine? <path name> Description Under the PATH subsys tem, this command is use d to defin e or redefin e the switch s ettin ...

  • Agilent Technologies 87130A - page 77

    Agilent 87130A Operating and Service Manual 4-35 Remote Operation :DEFine Example Command ROUTE:PATH:DEF ATTEN_14,(@101,2(0:5)),( @102); This command defines a pat h whose name i s ATTEN_14 whose first channel list a ffe cts channe l 1 on card 1 a nd channels 0 through 5 on card 2, a nd whose seco nd chann el list affect s channel 2 on card 1 . Exa ...

  • Agilent Technologies 87130A - page 78

    4-36 Agilent 87130A Operating and Service Manual Remote Operation :DELay :DELay Synta x ROUTe:DELay:<delay time>, Description This comman ds sets the d elay time in sec onds require d to val idate t he sense lines on a relay f or which sen sing will be used. The d rive sign al will be held on th e relay f or this a mount of ti me afte r the p ...

  • Agilent Technologies 87130A - page 79

    Agilent 87130A Operating and Service Manual 4-37 Remote Operation :DEL ay NOTE The query fo rm is not av ailable when usi ng a path name due to the potent ial for conf usion bet ween the first g roup and th e second in the pa th. ...

  • Agilent Technologies 87130A - page 80

    4-38 Agilent 87130A Operating and Service Manual Remote Operation :DELete :DELete Synta x ROUTE : DELete Description This command delet es: • All data associat ed with the specifie d path or group a nd frees up the path stor age r egis ter. • All ch an nels from the PFAIL list . This command sets memory t o an init ial sta te. NOTE The :DELete ...

  • Agilent Technologies 87130A - page 81

    Agilent 87130A Operating and Service Manual 4-39 Remote Operation :DELete • MEMory:DELete; MEMory:DELete erase s all d ata fr om CM OS R AM, by f illin g it with ze roe s, and th en sets it to an ini ti al st ate. T hat sta te is as fo llo ws: ❍ The p ower fail cha nne l lis ts ar e em pt y ( ROUT:PFA:CLOS and ROUT:PFA:OPEN ). ❍ Sensing (VER ...

  • Agilent Technologies 87130A - page 82

    4-40 Agilent 87130A Operating and Service Manual Remote Operation :DRIVe :DRIV e Synta x ROUTe:DRIVe : ALL ROUTe:DRIVe [?]<channel list> ROUTe:DRIVe : <pathname> Description There is a list of r elays con sidered un used or “ not t here ” by the f irmware. Unused chann els are not driven even i f included in a channel l ist or path ...

  • Agilent Technologies 87130A - page 83

    Agilent 87130A Operating and Service Manual 4-41 Remote Operation :DRIVe Example Query • ROUTE:DRIVE:ON? (@101,103,105); This comman d returns a l ist of 1 ’ s and 0 ’ s, separated by commas, depending on whether drive is on or of f for the indic ated chan nels. If it is on for c hannels 10 1 and 105 and off for 103, th e switch dr iver wil l ...

  • Agilent Technologies 87130A - page 84

    4-42 Agilent 87130A Operating and Service Manual Remote Operation :EERom :EERom Synta x DIAGnostics:EERom:CYCLes? Description This func tion allows EERom informati on to be read out. (Refer to :CYCLes? on p age 4-33 .) ...

  • Agilent Technologies 87130A - page 85

    Agilent 87130A Operating and Service Manual 4-43 Remote Operation :ERRor? :ERRor? Synta x SYSTem:ERRor? Description As SC PI sp eci fies , th is r eads o ut th e fu ll er ror numb er a nd e rror d esc ript ion for the first e rror in t he error queue. It can be iss ued repeat edly un til the queue is empty (indi cated by 0 ,”No error” ). All po ...

  • Agilent Technologies 87130A - page 86

    4-44 Agilent 87130A Operating and Service Manual Remote Operation :ERRor? -181,Invalid outside macro definition -183,Invalid inside macro definition Execu tio n Errors These set the Exec Err bit in ESR. -200,Execution error -222,Data out of range -223,Too much data -270,Macro error -272,Macro execution error -273,Illegal macro label -276,Macro recu ...

  • Agilent Technologies 87130A - page 87

    Agilent 87130A Operating and Service Manual 4-45 Remote Operation :ERRor? 1004,EEROM data invalid Corrupti on has been detected in the EEROM; i t needs to be replaced, or , if brand new , it nee ds to have ME M:SAVE executed once. 1006,Channel timeout <17 hex digits> This erro r is g ener ated wh en a re lay app arent ly f ails to sw itc h, b ...

  • Agilent Technologies 87130A - page 88

    4-46 Agilent 87130A Operating and Service Manual Remote Operation :FREE? :FREE? Synta x MEMory:Free? Description This is a query which retu rns the nu mber of b ytes that remain in RAM for storin g configur ation dat a, followed by the numbe r of bytes in itiall y availa ble. The two q uantiti es are separ ated by commas . For a brand new system th ...

  • Agilent Technologies 87130A - page 89

    Agilent 87130A Operating and Service Manual 4-47 Remote Operation :GROUP :GROUP Synta x ROUTE: GROUP: Description The GROUP subsy stem allo ws grouping o f paths t o customize the manual interf ace to th e 87130A. A “ group ” is an ordere d collection of up to 256 pa ths. Pat hs can be colle cted into mean ingful gr oups using the GROUP command ...

  • Agilent Technologies 87130A - page 90

    4-48 Agilent 87130A Operating and Service Manual Remote Operation :INITialize :INITialize Synta x MEMory:INITialize Description When t his co mm and is issu ed , RA M is ini tial ized acco rding to t he fol lowin g algori thm: 1. RAM is in itialized to the state de scribed i n MEMory:DELete . This command esse ntially erases a ny changes t hat have ...

  • Agilent Technologies 87130A - page 91

    Agilent 87130A Operating and Service Manual 4-49 Remote Operation :LAB el [?] :LABel[?] Synta x ROUTe :LABEL “ <label> ” ; Description This command specifie s a label (32 chara cters max) to be used when labeli ng the grou p on manual i nterfac e screens . Any charact er may be us ed within t he quotes as long as its value is between 32 a ...

  • Agilent Technologies 87130A - page 92

    4-50 Agilent 87130A Operating and Service Manual Remote Operation MEMory MEMory Synta x MEMory Description The MEMory subs ystem is us ed to delete , initia lize RAM, and sa ve EEROM info rmation t o the co ntrolle r . :DELete :INITialize :SAVE : FREE?        ...

  • Agilent Technologies 87130A - page 93

    Agilent 87130A Operating and Service Manual 4-51 Remote Operation :NAME :NAME Synta x ROUTE:GROUP:NAME <number>,<group name> Description The groups are numbere d from 1 to 16. The y may be named or renamed using th is command. An at tempt to n ame a group us ing a name al ready in use for another gr oup will r esult in an error . A grou ...

  • Agilent Technologies 87130A - page 94

    4-52 Agilent 87130A Operating and Service Manual Remote Operation :OPEN :OPEN Synta x ROUTe:OPEN[?] ROUTe:PFail:OPEN[?] Description Each cha nnel has a CLOSE or OPEN p osition. On Agilent r elays, the OPEN path i s th e pa th be twee n th e in put te rmi nal labe led 1 on th e re lay and th e input t erminal label ed C. It is r ecognized that CLOSE ...

  • Agilent Technologies 87130A - page 95

    Agilent 87130A Operating and Service Manual 4-53 Remote Operation :OPE N It is possi ble to combine OPEN and CLOSE in a singl e command si nce they are both par t of the ROUTe subsys tem. For exampl e: ROUTE:CLOSE (@406:410);OPEN (@202); This command will clos e channels 6 through 1 0 on card 4 a nd open channel 2 on card 2. Example Command ROUTE:O ...

  • Agilent Technologies 87130A - page 96

    4-54 Agilent 87130A Operating and Service Manual Remote Operation :OPEN Example Query ROUTE:PFAil:OPEN? (@10 1,205) ; The incl usion of a question ma rk causes a readback of the power up state of the requ ested cha nnels as a li st of 1s a nd 0s separ ated by commas . ❍ A 1 means the channel i s in the P F A:OPEN list . ❍ A 0 means tha t it is ...

  • Agilent Technologies 87130A - page 97

    Agilent 87130A Operating and Service Manual 4-55 Remote Operation :PATH :P A TH Synta x ROUTe:PATH Description The PATH subsys tem a llo ws s tori ng of cha nnel l ists to si mp lify re mo te access a nd to cust omize the man ual inte rface to the 8713 0A. • Paths ar e specif ied using CLOSE and OPEN channel lists. Each relay contain s one CLOSE ...

  • Agilent Technologies 87130A - page 98

    4-56 Agilent 87130A Operating and Service Manual Remote Operation :PFAil :PF Ail Synta x ROUTe:PFAil Description The ROUT e:PF Ail subsyste m of SCPI all ows specif ication of wh ich channels will be c losed on a p ower cycle (or *RST or *TST?) . • Channels not specifi ed by ROUTE:PF AIL:CLOSE or ROUTE:PF AIL:OPEN are set duri ng power up by read ...

  • Agilent Technologies 87130A - page 99

    Agilent 87130A Operating and Service Manual 4-57 Remote Operation :REM ove :REMove Synta x ROUTe:GROUP:REMove <group name>,<path n ame> Description This comman d removes all i nstances of the specifi ed path from a gro up. The group name a nd path name must have bee n previously defined us ing GROUP:NAME and PATH:DEF. Example Command RO ...

  • Agilent Technologies 87130A - page 100

    4-58 Agilent 87130A Operating and Service Manual Remote Operation ROUTe ROUT e Synta x Refe r to t he com man d tre e. Description Relay swi tching and configura tion is acc omplished by the ROUTe comm and tree. ...

  • Agilent Technologies 87130A - page 101

    Agilent 87130A Operating and Service Manual 4-59 Remote Operation :SAVE :SA VE Synta x MEMory:SAVE Description This command copies the RAM i mage to the EEROM. Care shoul d be taken to do th is onl y wh en nec essa ry , du e to the lim ited lif e of t he EER OM. (Refe r to DIAG:EEROM:CYCLES? ). Becaus e this is t ime consuming ( over a minute in so ...

  • Agilent Technologies 87130A - page 102

    4-60 Agilent 87130A Operating and Service Manual Remote Operation STATus ST A T us Synta x STATus:OPERation STATus:QUEStionable Description The ST A T us subs ystem is full y specif ied by SCPI. Re fer to th e following comm and s: *STB (Status Byte) , *SRE (Request Enabl e) , *ESE (Event Status Enable) , and *ESR? (Even t Status Register Query) ? ...

  • Agilent Technologies 87130A - page 103

    Agilent 87130A Operating and Service Manual 4-61 Remote Operation SYST em SYST em Synta x SYSTEM Description These ar e SYST em commands from the SCPI specific ation. • VERSion? • ERRor? :VERSion? :ERRor ?    ...

  • Agilent Technologies 87130A - page 104

    4-62 Agilent 87130A Operating and Service Manual Remote Operation TRIGger TRIGger Synta x TRIGger:SEQuence:DELay <number> Description This command allows the user to cont rol the 24 V power suppl y recovery time. Inp ut values are limit ed to bet ween 0 and 200 msec (200 msec is the default setting) . The GPIB c ommand TRIGger:SEQuence:DELay ...

  • Agilent Technologies 87130A - page 105

    Agilent 87130A Operating and Service Manual 4-63 Remote Operation :VALue :V ALue Synta x ROUTe:PATH:VALUE <path name>,<number>; Description This comman d specif ies a numbe r (int eger in the range – 32768 to 32767) to be used whe n labeli ng the path on manual in terface screens. T his number , when enter ed manua lly from t he user ...

  • Agilent Technologies 87130A - page 106

    4-64 Agilent 87130A Operating and Service Manual Remote Operation :VERify :VERify Synta x ROUTe:VERify ROUTe:VERify [?] Description This command a dds or remove s relays f rom the “ sen se list ” , th e list of relays for wh ich sensi ng is enab led. This command only works with relays tha t have the abili ty to sense the state of the swi tch . ...

  • Agilent Technologies 87130A - page 107

    Agilent 87130A Operating and Service Manual 4-65 Remote Operation :VERify ROUTE:VERIFY:ON ATTEN_14; This comm an d cau ses t he s et o f swit che s de fined by th e P A TH wi th th e pathname ATTEN_14 to be added to (ON) or removed from (OFF) the "sense list . All swi tche s refe ren ced in ei the r chan nel list in th e pa th ar e add ed (O N ...

  • Agilent Technologies 87130A - page 108

    4-66 Agilent 87130A Operating and Service Manual Remote Operation :VERsion ? :VERsion? Synta x SYSTem:VERSion? Description This rea ds out the firmwar e datecod e. ...

  • Agilent Technologies 87130A - page 109

    Agilent 87130A Operating and Service Manual 4-67 Remote Operation :WIDTh :WIDTh Synta x ROUTe:WIDTh <pulse width> , ROUTe:WIDTh <channel list> Description This command sets the pulse width in sec onds required to cl ose a relay . The pulse wid th may be set in 5 ms inc rements up t o 1275 ms. The p ulse width default s to 30 ms when mem ...

  • Agilent Technologies 87130A - page 110

    4-68 Agilent 87130A Operating and Service Manual Remote Operation Example Prog rams Example Pr ograms The foll owing progr ams writte n in Rocky Mount ain Basic pro vide sa mple programs t hat may be hel pful in progr amming the 871 30A. Save Memory In order to use th e followi ng program, you must first cre ate a fi le named SWDATA . The foll owin ...

  • Agilent Technologies 87130A - page 111

    Agilent 87130A Operating and Service Manual 4-69 Remote Operation Example Programs 280 ENTER @Sw;A$ 290 I=-1 300 WHILE LEN(A$)>0 310 Comma=POS(A$, ” , ” ) 320 IF Comma=0 THEN 330 A$=A$& ” , ” 340 Comma=LEN(A$) 350 END IF 360 I=I+1 370 Groupnames$(I)=A$[1;Comma-1] 380 A$=A$[Comma+1] 390 END WHILE 400 OUTPUT @File;Groupnames$(*) 410 Ma ...

  • Agilent Technologies 87130A - page 112

    4-70 Agilent 87130A Operating and Service Manual Remote Operation Example Prog rams 670 WHILE LEN(A$)>0 680 Comma=POS(A$, ” , ” ) 690 IF Comma=0 THEN 700 A$=A$& ” , ” 710 Comma=LEN(A$) 720 END IF 730 I=I+1 740 Pathnames$(I)=A$[1;Comma-1] 750 A$=A$[Comma+1] 760 END WHILE 770 OUTPUT @File;Pathnames$(*) 780 Max_path=I 790 FOR P=0 TO Max ...

  • Agilent Technologies 87130A - page 113

    Agilent 87130A Operating and Service Manual 4-71 Remote Operation Example Programs Resto r e Mem ory The foll owing progr am can be use d to rest ore the EEROM st ate read o ut by READMEM: 10 ! WRITEMEM program. Takes a file written by READMEM and sends it to the 87130A. 20 DIM A$[32767] 30 DIM Respond(31),Sense(7,31),Unused(7,31),Pfac(7,3 1), Pfao ...

  • Agilent Technologies 87130A - page 114

    4-72 Agilent 87130A Operating and Service Manual Remote Operation Example Prog rams 330 ENTER @File;Pathnames$(*) 340 FOR I=0 TO 255 ! send path dat a 350 IF Pathnames$(I)<> ”” THEN 360 ENTER @File;A$ 370 OUTPUT@Sw; ” ROUT:PATH:DEF ” &Pathna mes$(I)& ” , ” &A$& ” ; ” 380 END IF 390 NEXT I 400 FOR I=0 TO 15 ! se ...

  • Agilent Technologies 87130A - page 115

    Agilent 87130A Operating and Service Manual 4-73 Remote Operation Example Programs 650 END 660 SUB Getandsend_bmap(B$) 670 ! Loads a query response from file and outputs it as a channel list 680 COM @File,@Sw 690 DIM Bitmap(7,31),A$[32767] 700 ENTER @File;Bitmap(*) 710 FOR I=0 TO 7 720 A$= ”” 730 FOR J=0 TO 31 740 IF Bitmap(I,J) THEN A$=A$& ...

  • Agilent Technologies 87130A - page 116

    4-74 Agilent 87130A Operating and Service Manual Remote Operation Example Speed Calculation Example Speed Calculation Switchin g speed is a functi on of puls e widths, s ensing del ays, the s tate of the chosen c hannels, the seque nce of r elays dr iven and the power suply re covery time. A sampl e program a nd timing diagr am are provide d to hel ...

  • Agilent Technologies 87130A - page 117

    Agilent 87130A Operating and Service Manual 4-75 Remote Operation Example Speed Calculation 60 ! a range. 70 OUTPUT 709; ” ROUT:DRIV:OFF (@112:130) ; ” 80 ! 90 ! Drive is set to OFF for remaining channels on driver 100 ! card 1.Unless channels are part of Drive list , no 110 ! pulse (:WIDTh) is sent. 120 OUTPUT 709; ” ROUT:VER:ON (@100:111); ...

  • Agilent Technologies 87130A - page 118

    4-76 Agilent 87130A Operating and Service Manual Remote Operation Example Speed Calculation 380 OUTPUT 709; ” ROUT:WIDT .04,(@100,10 2,104,108); ” 390 ! 400 ! Pulse (:WIDTh) is set to 40 ms for channels 100,102, 410 ! 104, and 108. When :OPEN is sent, 100 and 10 2 420 ! will OPEN at the same time. 430 ! Channels 104 and 108 will e ach OPEN at d ...

  • Agilent Technologies 87130A - page 119

    Agilent 87130A Operating and Service Manual 4-77 Remote Operation Example Speed Calculation 780 ! See timing chart to predict when each relay will 790 ! open. 800 OUTPUT 709; ” ROUT:OPEN? (@100:104,10 8:111); ” 810 ! 820 ! You turned sensing off for 1 04 thru 107, remember? 830 ! About OPEN?: you could still query for the entire 840 ! open list ...

  • Agilent Technologies 87130A - page 120

    4-78 Agilent 87130A Operating and Service Manual Remote Operation Example Speed Calculation ...

  • Agilent Technologies 87130A - page 121

    Agilent 87130A Operating and Service Manual 5-1 5 Replaceable Par ts Overview I n this cha pter you wi ll find: • Accessor ies avail able for the swit ch driver by part numbe r and descri ption. • All repl aceable parts re ferenced i n chassi s and cable assemblie s. ...

  • Agilent Technologies 87130A - page 122

    5-2 Agilent 87130A Operating and Service Manual Replaceable Parts This page int enti onally l eft blank ...

  • Agilent Technologies 87130A - page 123

    Agilent 87130A Operating and Service Manual 5-3 Replaceable Parts Accessory Boards and Cables Addition al driver boards, i nterconne ct boards, and cable s provide expanded capacit y , remote swit ching and ev erything needed for dev ice connec tion. Fi rmwa r e Re vis ions Ol der v ersi ons of th is inst rum en t may h ave firmw ar e par t num ber ...

  • Agilent Technologies 87130A - page 124

    5-4 Agilent 87130A Operating and Service Manual Replaceable Parts T able 5-2 Replaceab le Parts - 87130A Chassi s Assembly ( 1) Part Location Part Number Quantity Descriptio n Reference Designator 1 87130-00009 1 D eck — 2 87130-0 001 1 1 Power supply shield — 3 87130-6 2065 1 Driver boar d A2 4 87130-0 0010 1 PC board bracket ass embly — 5 8 ...

  • Agilent Technologies 87130A - page 125

    Agilent 87130A Operating and Service Manual 5-5 Replaceable Parts Figure 5-1 87130A Chassi s Assembly ( 1) ...

  • Agilent Technologies 87130A - page 126

    5-6 Agilent 87130A Operating and Service Manual Replaceable Parts T able 5-3 Replaceab le Parts - 87130A Chassi s Assembly ( 2) Part Location Part Number Quantity Description 1 5021-8401 1 Front fr ame 2 5021-58 02 1 Rear frame 3 5021-58 87 2 S ide strut 4 5041-88 02 1 T op trim 5 5063-92 26 1 Front ha ndle kit 6 5021-8495 2 Trim, front handle 7 50 ...

  • Agilent Technologies 87130A - page 127

    Agilent 87130A Operating and Service Manual 5-7 Replaceable Parts Figure 5-2 87130A Chassi s Assembly ( 2) ...

  • Agilent Technologies 87130A - page 128

    5-8 Agilent 87130A Operating and Service Manual Replaceable Parts 1 Required fo r 220V options T able 5-4 Replac eable Part s - 87130A Cable As sembly Part Location Part N umber Quantity Description Reference D esignator 1 87130-6206 5 1 Dr iver board A2 2 87130-6000 2 1 Cont roller boa rd A1 3 0950-2252 1 Power supply 1 10 W A3 4 87130-6000 1 1 Di ...

  • Agilent Technologies 87130A - page 129

    Agilent 87130A Operating and Service Manual 5-9 Replaceable Parts Figure 5-3 87130A Cable Assembly ...

  • Agilent Technologies 87130A - page 130

    5-10 Agilent 87130A Operating and Service Manual Replaceable Parts ...

  • Agilent Technologies 87130A - page 131

    Agilent 87130A Operating and Service Manual 6-1 6 T r oubleshooting Overview I n this cha pter you wi ll find: • How to check the fuses and power s upply • How to set up the EPROM af ter rep lacement ...

  • Agilent Technologies 87130A - page 132

    6-2 Agilent 87130A Operating and Service Manual Troubleshooting Troubleshoo ting T roubleshooting If your instrument is still in warrant y we stron gly recommend that you s end the en tire unit b ack to Ag ile nt T ec hnolo gie s for r epa ir . A procedur e for che cking the fu ses and p ower supply is given on page 6-4 . W ARNING • T o avoid ele ...

  • Agilent Technologies 87130A - page 133

    Agilent 87130A Operating and Service Manual 6-3 Troubleshooting Troubleshoot ing Figure 6-1 87130A DC Schemat ic ...

  • Agilent Technologies 87130A - page 134

    6-4 Agilent 87130A Operating and Service Manual Troubleshooting Fuse and Power Supp ly Check Fuse and Power Supply Check Fuse Check If the attenuat or/switc h driver f ails to respond whe n the power s witch is turned on, t he power line fuse should be check ed. The 1 A, 250 V time delay , power li ne fuse (p art numb er 21 10-0 782) is lo cated in ...

  • Agilent Technologies 87130A - page 135

    Agilent 87130A Operating and Service Manual 6-5 Troubleshooting Procedure f or Setting Up the EPROM Pr ocedure for Setting Up the EPROM Use the f ollowing pr ocedure to s et up the EPROM af ter the EPROM or the CPU board has been repl aced. • T o set up the EPROM fr om the cont roller , use the fol lowing commands: "MEM:DEL; Delete s ev eryt ...

  • Agilent Technologies 87130A - page 136

    6-6 Agilent 87130A Operating and Service Manual Troubleshooting Procedure for S etting Up the EPROM ...

  • Agilent Technologies 87130A - page 137

    Index Agilent 87130A Operating and Service Manual Index-1 A accessorie s, description, 5-13 ADD, 4-27 address channel , 2-4 dri ver ca rd, 2-11 factory preset , 2-3 GPIB, 2-3 switch dr iver, 4 -4 AUTOselect, 4-28 B block di agram , 1-2 boards, acc essory, 5-13 C cable I/O data, 2-13 outp ut, 2- 14 cables, a ccessory, 5-13 CA T alo g, 4- 29 channel ...

  • Agilent Technologies 87130A - page 138

    Index-2 Agilent 87130A Operating and Service Manual comp ound , 4-5 optio ns, 4-6 I I/O data cable descri ption , 2-13 pin fu nction s, 2-13 IDN, 4-16 If, 6-2 initiali zation, 4-9 INIT ialize, 4-48 inspectio n, 2-2 installatio n, 2-1 instrument status, 4-11 interface seIect co de, 4 -4 L LABel, 4-49 M MEMory, 4-50 multip le driver ca rds, conne cti ...

  • Agilent Technologies 87130A - page 139

    Agilent 87130A Operating and Service Manual Index-3 SA VE, 4-5 9 ST A Tus, 4-6 0 SYST em, 4 -61 TRIGger, 4-62 VA L u e , 4 - 6 3 VERify, 4-64 VERsion , 4-66 WID Th, 4-67 selecting m ultiple subs ystems, 4-5 sensing delay, 1 -3 serial number, 4-48 setting up the switch driver, 4-9 specifications enviro nmental, 3 -3 SRE, 4 -19 ST A Tus, 4-6 0 status ...

  • Agilent Technologies 87130A - page 140

    Index-4 Agilent 87130A Operating and Service Manual ...

Manufacturer Agilent Technologies Category Switch

Documents that we receive from a manufacturer of a Agilent Technologies 87130A can be divided into several groups. They are, among others:
- Agilent Technologies technical drawings
- 87130A manuals
- Agilent Technologies product data sheets
- information booklets
- or energy labels Agilent Technologies 87130A
All of them are important, but the most important information from the point of view of use of the device are in the user manual Agilent Technologies 87130A.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Agilent Technologies 87130A, service manual, brief instructions and user manuals Agilent Technologies 87130A. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Agilent Technologies 87130A.

Similar manuals

A complete manual for the device Agilent Technologies 87130A, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Agilent Technologies 87130A by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Agilent Technologies 87130A.

A complete Agilent Technologies manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Agilent Technologies 87130A - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Agilent Technologies 87130A, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Agilent Technologies 87130A, that we can find in the current document
3. Tips how to use the basic functions of the device Agilent Technologies 87130A - which should help us in our first steps of using Agilent Technologies 87130A
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Agilent Technologies 87130A
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Agilent Technologies 87130A in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Agilent Technologies 87130A?

Use the form below

If you did not solve your problem by using a manual Agilent Technologies 87130A, ask a question using the form below. If a user had a similar problem with Agilent Technologies 87130A it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)