English dropdown-ico

Manual JVC GY-HM600E

136 pages 12.62 mb
Download

Go to site of 136

Summary
  • JVC GY-HM600E - page 1

    . HD MEMORY CARD CAMERA RECORDER GY-HM600U/GY-HM600E INSTRUCTIONS . T I M E C O D E The specifications and appearance of this product are subject to changes for further improvement without prior notice. Please check the latest version of the INSTRUCTIONS from the following Mobile User Guide, or download the PDF from the URL below. Mobile User Guide ...

  • JVC GY-HM600E - page 2

    . 1. Read these instructions. 2. K eep these instr uctions. IMPORT ANT SAFEGU ARDS 4. F ollow all instructions. 5. Do not use this apparatus near water . 6. Clean only with dr y cloth. 7. Do not bloc k any ventilation openings . Install in accordance with the manufacturer’ s instructions. 8. Do not install near any heat sources such as radiators ...

  • JVC GY-HM600E - page 3

    Safety Precautions . CA UTION FOR USA AND CANAD A CA UTION: T O REDUCE THE RISK OF ELECTRIC SHOCK. DO NO T REMO VE CO VER (OR BA CK). NO USER-SER VICEABLE P AR TS INSIDE. REFER SER VICING T O QU ALIFIED SER VICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle is intended to aler t the user to the presence of uni ...

  • JVC GY-HM600E - page 4

    . POUR CANAD A RISQUE D’ELECTROCUTION NE P AS OUVRIR CA UTION: The mains plug shall remain readily operab le.  Remov e the mains plug immediately if the camera functions abnormally . W ARNING: The batter y pack, the camer a with batter y installed, and the remote control with batter y installed should not be e xposed to excessiv e heat such as ...

  • JVC GY-HM600E - page 5

    . When the equipment is installed in a cabinet or on a shelf , make sure that it has sufficient space on all sides to allow f or ventilation (10 cm (3-15/16 " ) or more on both sides, on top and at the rear). Do not bloc k the ventilation holes. (If the ventilation holes are b lock ed by a newspaper , or cloth etc. the heat may not be able to ...

  • JVC GY-HM600E - page 6

    . IMPORT ANT (for owner s in the U. K . ) Connection to the mains supply in the United Kingdom. DO NO T cut off the mains plug from this equipment. If the plug fitted is not suitable f or the power points in y our home or the cable is too shor t to reach a power point, then obtain an appropriate safety appro ved e xtension lead or consult your deal ...

  • JVC GY-HM600E - page 7

    . Information f or Users on Disposal of Old Equipment and Batteries [European Union] These symbols indicate that the electrical and electronic equipment and the batter y with this symbol should not be disposed of as general household waste at its end-of-lif e. Instead, the products should be handed ov er to the applicable collection points f or the ...

  • JVC GY-HM600E - page 8

    Contents Introduction Safety Precautions ............................................ 3 Contents ............................................................ 8 Main Features ................................................. 10 Precautions for Proper Use ............................. 12 Operation Modes ............................................. 1 ...

  • JVC GY-HM600E - page 9

    Display Settings Item ................................... 99 A/V Set Menu ................................................ 101 Video Set Item ........................................... 101 Audio Set Item ........................................... 102 System Menu ................................................ 104 Record Set Item ................ ...

  • JVC GY-HM600E - page 10

    Main Features F11 Sensitivity, 1/3-inch Full HD 3CMOS Sensors This camera recorder is equipped with three 1/3- inch 2.07M pixels full HD CMOS sensors. It delivers high image quality, high color resolution through processing of individual R, G, B color signals. 12-bit signal processing and the new 2D DNR removes dark current and optical shot noise w ...

  • JVC GY-HM600E - page 11

    4-position ND Filter This camera recorder incorporates three types of ND filters. Adjust the amount of light according to the brightness during shooting by switching the 4- position ND filter (OFF, 1/4, 1/16, 1/64). 0.45-inch 1.22M Pixel Color Viewfinder, 3.5-inch 920K Pixel LCD Display (Equipped with Focus Assist Function) Built-in Stereo Micropho ...

  • JVC GY-HM600E - page 12

    Precautions for Proper Use Storage and Usage Locations o Allowable ambient temperature and humidity Be sure to use this unit within the allowable temperature range of 0 °C to 40 °C (32 °F to 104°F) and a relative humidity of 30 % to 80 %. Using this unit at a temperature or humidity outside the allowable ranges could result not only in malfunct ...

  • JVC GY-HM600E - page 13

    Regular Inspection (Maintenance) Under normal environment, dust will accumulate on the camera recorder when it is used over a long period. Dust may enter the camera recorder especially if it is used outdoors. This may affect the image and sound quality of the camera recorder. Check and replace the fan after every 9000 hours (suggested guideline). Y ...

  • JVC GY-HM600E - page 14

    Others o Do not insert objects other than the memory card into the card slot. o Do not block the vent on the unit. Blocking of the vent causes internal heating and may lead to burns and fires. o Do not turn off the [POWER ON/OFF(CHG)] switch or remove the power cable during recording or playback. o The camera recorder may not show stable pictures f ...

  • JVC GY-HM600E - page 15

    License Notices o MPEGLA AVC THIS PRODUCT IS LICENSED UNDER THE AVC PATENT PORTFOLIO LICENSE FOR THE PERSONAL USE OF A CONSUMER OR OTHER USES IN WHICH IT DOES NOT RECEIVE REMUNERATION TO (i) ENCODE VIDEO IN COMPLIANCE WITH THE AVC STANDARD (“AVC VIDEO”) AND/OR (ii) DECODE AVC VIDEO THAT WAS ENCODED BY A CONSUMER ENGAGED IN A PERSONAL ACTIVITY A ...

  • JVC GY-HM600E - page 16

    Operation Modes This camera recorder has three operation modes - Camera mode, Media mode, and USB mode. . AE LEVEL MENU/THUMB CANCEL MODE Media Mode Thumbnail Display (Playback/P ause/ Fr ame-by-Fr ame/ F ast Forw ard/Rewind/ Clip Jump) Playback USB Connection (When the confirmation to change to USB mode appears and [Change] is selected) (USB Mass ...

  • JVC GY-HM600E - page 17

    Operation Mode Description Camera Mode 0 This is the camera shooting mode. The camera recorder starts up in Camera mode when the power is turned on. 0 Camera images are output on the viewfinder and LCD monitor. When a recordable SD card is inserted, the camera recorder enters the recording standby mode. “STBY” appears on the operation mode disp ...

  • JVC GY-HM600E - page 18

    Names of Parts . SERVO MANU AL ZOOM REC H E I J G D AC B K F FIX VA R OFF F O C U S A S S IS T /1 O IS /2 L O L U X /3 MENU/THUMB AE LEVEL FOCUS ND FILTER 1/64 1/1 6 1/4 OFF P O W E R M AR KER/6 ZEBRA/5 AE LOCK/4 SHUTTER W HT BAL CANCEL P U S H A U T O IR IS GAIN FULL AU TO PUSH AUTO PRESET B L M H A O N O F F ON MANU ∞ MODE O F F (CHG) SLO T A/B ...

  • JVC GY-HM600E - page 19

    . A U X INPUT 2 INPUT 1 DEV ICE AV A BA TT .RELEA SE P O W E R /C H G B HDMI REM OTE DC HD/SD SDI REC W T REC HOLD IN OUT TC L M N O d R S T X Z a b c Q P U V Y W R [REC] Record Trigger Button Starts/stops recording. Memo : 0 This button is interlocked with the [REC] button I at the bottom of the lens and the [REC/ HOLD] button Z at the top of the ...

  • JVC GY-HM600E - page 20

    Side Control Panel . ND FILTER FOCUS AE LEVEL MANU PUSH AUTO MENU/THUMB FOCUS ASSIST/1 OIS / 2 LOLUX / 3 1/64 1/16 1/4 OFF PRESET IRIS GAIN CANCEL L M H B A WHT BAL SHUTTER FULL AUTO MODE POWER ON OFF (CHG) ON OFF AE LOCK/4 ZEBRA/5 MARKER/6 PUSH AUTO TIME CODE AUTO A B C E S R Q O N M L K J T D P H I U F G A [FOCUS AUTO/MANU/∞] Focus Switch ( A P ...

  • JVC GY-HM600E - page 21

    R [OIS/2] Optical Image Stabilizer/User 2 Button For switching the image stabilizer feature mode ON or OFF. You can also use it as a user button by assigning a specific feature in the menu setting to this button. ( A P36 [Assigning Functions to User Buttons] ) S [FOCUS ASSIST/1] Focus Assist/User 1 Button For switching the focus assist function ON ...

  • JVC GY-HM600E - page 22

    LCD Monitor . MENU/THUMB CANCEL CH1 INT INPUT1 INPUT2 AUTO MANUAL CH2 INPUT2 MONITOR DISPLAY ST ATUS INPUT1 PEAKING LCD BRIGHT CH2 CH1 LINE MIC MIC +48V CH1 BOTH CH2 B C H I A D F G E J K L N M A LCD Monitor ( A P34 [Adjusting the LCD Monitor and Viewfinder] ) B [MENU/THUMB] Menu/Thumbnail Button 0 Displays the menu screen during Camera mode. ( A P ...

  • JVC GY-HM600E - page 23

    Lens Section . E CD A B A Filter Built-In Screw 0 Transparent or UV filter for lens protection, or filters for various effects can be installed. 0 Installable filter types: Φ72mmP0.75 Memo : 0 Remove the lens hood when installing the filter. ( A P26 [Attaching/Detaching the Hood] ) B Lens Cover Open/Close Switch ( A P26 [Opening/Closing the Lens C ...

  • JVC GY-HM600E - page 24

    Basic System Diagram . Wireless Microphone Receiver RCA pin AV C a b l e HDMI Cable [A UX] [T C] Carrying Case T ripod SDHC/SD XC Memory Card SDHC/SD XC Card Reader USB Cable Battery AC A dapter Remote Control Unit Non-linear Editing System G Y -HM600 Microphone Monitor Monitor SDI Cable BNC Earphone Shoulder Belt G Y -HM600 24 Introduction ...

  • JVC GY-HM600E - page 25

    Settings and Adjustments Before Use . Adjusting the Grip Belt Open the pad and adjust the position of the grip belt accordingly. . A U X INPUT2 INPUT1 D E V IC E A V A B A T T . R E L E A S E P O W E R /C H G B H D M I R EM O TE D C HD/ SD SDI REC Caution : 0 If the grip is loose, the camera recorder may fall off resulting in injuries or malfunctio ...

  • JVC GY-HM600E - page 26

    Opening/Closing the Lens Cover Use the lens cover open/close switch to open or close the lens cover. Before shooting, open the lens cover. When this camera recorder is not in use, close the lens cover to protect the lens. . Caution : 0 Do not press against the lens cover with force. Doing so may damage the lens or the cover. Attaching/Detaching the ...

  • JVC GY-HM600E - page 27

    1 Hold down the lock button (blue) at the center of the [POWER ON/OFF(CHG)] switch to set to “OFF(CHG)”. 2 Attach the supplied battery. Slide it in until you hear a click. 3 Connect the supplied AC adapter to the [DC] terminal. 4 Connect the AC adapter to a power outlet. 0 The [POWER/CHG] lamp blinks during charging and will go out after chargi ...

  • JVC GY-HM600E - page 28

    Using AC Power (DC IN Power) Use the supplied AC adapter to operate the camera recorder with AC power. . 1 MODE POWER ON OFF (CHG) 2 1 Connect the DC cable of the AC adapter to the [DC] terminal of the camera recorder. 0 Check that the power switch of the camera recorder is set to “OFF(CHG)”. 0 Open the cover of the [DC] terminal and connect as ...

  • JVC GY-HM600E - page 29

    Warnings by Lamp and Warning Tone Warning status is indicated by tally lamp and warning tone. 0 The tally lamp blinks. 0 The warning tone is output from the monitor speaker or [ x ] terminal. Memo : 0 If you continue to use the camera recorder while the power warning is displayed, the camera recorder will stop automatically when the battery or supp ...

  • JVC GY-HM600E - page 30

    Initial Settings When the power is first turned on, the Initial Setting screen for performing the initial settings in the camera recorder appears. Set the date/time of the built-in clock in the [Initial Setting] screen. All operations are disabled until initial settings are complete. . MODE POWER ON OFF (CHG) AE LEVEL MENU/THUMB CANCEL MENU/THUMB C ...

  • JVC GY-HM600E - page 31

    Memo : 0 The [Initial Setting] screen appears when the power is turned on for the first time and when the power is turned on after the built-in battery is fully discharged. 0 The configured date/time data is saved in the built-in rechargeable battery even if the power is turned off. 4 Set the time zone and date/time. A Move the cursor with the cros ...

  • JVC GY-HM600E - page 32

    Displays on the LCD Monitor and Viewfinder You can display the camera status, media information, zebra pattern, and various markers in the video image on the LCD monitor and viewfinder screen during shooting. Memo : 0 When [Main Menu] B [A/V Set] menu B [Video Set] B [Display On TV] is set to “On”, the display screen and menu screen are also di ...

  • JVC GY-HM600E - page 33

    Status Screen 0 This screen allows you to check the current settings. 0 To display the status screen, press the [STATUS] button in the normal screen. 0 The status display differs according to the operation mode (two types). ( A P16 [Operation Modes] ) 0 Press the [STATUS] button to switch to the display screen. 0 Press the [MENU] button at each sta ...

  • JVC GY-HM600E - page 34

    Adjusting the LCD Monitor and Viewfinder You can monitor video images on this camera recorder using the viewfinder, LCD monitor, or both. . DISPLA Y Normal LCD Inv er ted LCD Displays on the LCD Monitor and Viewfinder Screen (VF) When [LCD + VF] in the [LCD/VF] Menu is Set to “Off” ( A P97 [ LCD + VF ] ) LCD Monitor Status LCD Display VF Displa ...

  • JVC GY-HM600E - page 35

    Adjusting the Contour Use the [PEAKING +/ － ] button to adjust the contour of the LCD monitor. (The contour of the viewfinder screen will also be adjusted at the same time.) 0 The [+] button increases contour correction and the [ － ] button decreases contour correction. 0 Press the [+] and [ － ] buttons simultaneously to return to standard se ...

  • JVC GY-HM600E - page 36

    Assigning Functions to User Buttons You can assign functions to the following buttons and use them as user buttons. By assigning functions to the buttons, the usability of the camera recorder is enhanced. Perform settings in the menu items corresponding to each button. Button Menu Item [FOCUS ASSIST/1] Button [USER1] [OIS/2] Button [USER2] [LOLUX/3 ...

  • JVC GY-HM600E - page 37

    SD Card This camera recorder saves the recorded images and audio sound on the SD card (sold separately) in the card slot. Usable Cards Use a Class 6/10 SD card. Memo : 0 Depending on the recording format, SD card with Class 4 or higher performance can also be used. ( A P43 [Selecting System Definition, File Format and Video Format] ) Caution : 0 Us ...

  • JVC GY-HM600E - page 38

    Inserting an SD Card This camera recorder comes with two card slots (Slot A and B) for video/audio recording and playback. . 1 2 3 1 A B 2 1 Open the SD card cover. 2 Insert an SD card with the notched corner pointing up. The status indicator of the card slot to which the card was inserted lights up in red. 3 Close the SD card cover. Card Slot Stat ...

  • JVC GY-HM600E - page 39

    Switching the SD cards When both card slots are inserted with SD cards, you can use the [SLOT A/B] button to switch the card to use. When the memory on an SD card is full during recording, data recording automatically switches to the other card. . AE LEVEL MENU/THUMB CANCEL MENU/THUMB CANCEL SLOT A/B Memo : 0 The [SLOT A/B] button is disabled durin ...

  • JVC GY-HM600E - page 40

    6 Formatting is complete. When formatting is complete, “Complete” appears and the camera recorder returns to the [Format Media] screen. Memo : 0 During formatting, menu operation is unavailable but you can start recording. However, this is only available when a recordable SD card is inserted in the other slot. 0 Formatting cannot be performed i ...

  • JVC GY-HM600E - page 41

    Clips Recorded to SD Cards Folders in the SD Card Images captured are recorded to the [PRIVATE] folder inside the SD card. Images recorded are sorted into the respective folders according to the menu settings below. System Setting Format Setting Record Folder HD MOV JVC/CQAV HD MP4 JVC/BPAV HD AVCHD AVCHD SD MOV JVC/CQAVC Memo : 0 By formatting (in ...

  • JVC GY-HM600E - page 42

    Basic Shooting Procedures Preparations . 3 1 MODE POWER ON OFF (CHG) 4 2 4 1 Supply battery or AC adapter power to the camera recorder. ( A P26 [Power Supply] ) 2 Insert an SD card. ( A P37 [SD Card] ) 3 Turn on the power of the camera recorder. Hold down the lock button (blue) at the center of the [POWER ON/OFF(CHG)] switch to set to “ON”. The ...

  • JVC GY-HM600E - page 43

    Selecting System Definition, File Format and Video Format You can select the system definition (HD or SD), file format for recording/playback and the record format for video images on this camera recorder. Memo : 0 Make a selection in [Main Menu] B [Record Format] menu. Selecting a System Definition Select the system definition in [System]. There a ...

  • JVC GY-HM600E - page 44

    Selecting the Aspect Ratio of SD Videos Select an aspect ratio for the images. The available options vary as follows depending on the [System] setting. 0 For “HD”: Fixed at 16:9 0 For “SD”: Can select 16:9 or 4:3 Setting the Record Format Menu 1 Display the [Main Menu] B [Record Format] menu. 2 Set each of the items. 3 After setting is comp ...

  • JVC GY-HM600E - page 45

    Using Zoom Ring at the Lens Section 1 Set the [ZOOM SERVO/MANUAL] switch to “MANUAL”. You can adjust the preferred angle of view by turning the zoom ring. Saving/Recalling Current Zoom Position (Preset Zoom) This allows you to register up to three zoom positions. 1 Assign the “Preset Zoom1”, “Preset Zoom2”, or “Preset Zoom3” functio ...

  • JVC GY-HM600E - page 46

    Adjusting Focus Automatically 1 Set the [FOCUS AUTO/MANU/∞] switch to “AUTO”. The auto focus icon e appears on the screen. One Push Auto Focus While in the Manual Focus mode, pressing the [PUSH AUTO] button (within 1 minute) makes the camera recorder focus on the center of the frame automatically. Memo : 0 Face detection does not work during ...

  • JVC GY-HM600E - page 47

    . AE LEVEL MENU/THUMB CANCEL MENU/THUMB CANCEL 1 Assign the “Face Detect” function to any of the user buttons. ( A P36 [Assigning Functions to User Buttons] ) 2 Focus the camera recorder on a person and press the user button that is assigned with “Face Detect”. 0 When Face detection is enabled, the face detection icon ( q ) appears. 0 When ...

  • JVC GY-HM600E - page 48

    Adjusting the Brightness Adjust the brightness using Iris, Gain, Shutter speed and ND filter according to the brightness of the object. Adjusting the Brightness Automatically When the [FULL AUTO] switch is set to “ON”, Iris, Gain, Shutter speed and ND filter are automatically adjusted according to the brightness of the object to maintain optimu ...

  • JVC GY-HM600E - page 49

    Adjusting the Iris You can adjust the aperture of the lens iris manually or automatically according to the brightness of the object. . IRIS PUSH AUT O Manual Iris (Manual Adjustment) Mode The aperture value (F-number) of the lens can be set manually. 1 Press the [IRIS] button to set to the Manual Iris mode. The a icon on the screen disappears. 2 Tu ...

  • JVC GY-HM600E - page 50

    Setting the Gain This function electrically boosts the light sensitivity when there is insufficient illumination on the object. You can set the gain of the video amplifier according to the brightness of the object. Select the setting mode according to your shooting conditions. . GAIN L M H FULL AUT O ON OFF Fixed Gain Mode (Manual Gain Switching) 1 ...

  • JVC GY-HM600E - page 51

    Setting the Electronic Shutter You can change the shutter speed (time for each shooting frame) using the electronic shutter function. Electronic shutter can be adjusted manually or automatically. Fixed Shutter Mode (Manual Shutter Switching) 1 Press the [SHUTTER] button to set to the Manual Shutter mode. 0 The a icon on the screen disappears. 0 Use ...

  • JVC GY-HM600E - page 52

    During Variable Frame Rec . 720/30p, 720/24p, 1080/30p, 1080/24p 60, 30, 15 54, 27 50, 25 48, 24, 12, 6 45, 22.5 40, 20, 10 36, 18 32, 2 J ON ^^ ^ ^ ^ ^ ^ 1/10000 ^^ ^ ^ ^ ^ 1/10000 1/4000 ^^ ^ ^ ^ 1/10000 1/4000 1/2000 ^^ ^ ^ 1/10000 1/4000 1/2000 1/1000 ^^ ^ 1/10000 1/4000 1/2000 1/1000 1/500 ^^ 1/10000 1/4000 1/2000 1/100 0 1/500 1/250 ^ 1/10000 ...

  • JVC GY-HM600E - page 53

    Automatic Shutter Mode (Automatic Shutter Adjustment) 1 Press the [SHUTTER] button or set the [FULL AUTO] switch to “ON” to enter Automatic Shutter mode. 0 The a icon appears on the screen. 0 The camera recorder enters the automatic shutter adjustment mode. The shutter speed is automatically adjusted according to the brightness of the object. M ...

  • JVC GY-HM600E - page 54

    Preset Mode (PRESET) 0 Two different color temperature settings are registered on this camera recorder. You can switch between them using the [ y ] button. (Default setting: “3200K” 1 “5600K”) 0 Press the [ y ] button to switch to a different color temperature. (“Preset Temp.” 1 “Alternative Temp.”) 1 Set the [WHT BAL B/A/PRESET] sw ...

  • JVC GY-HM600E - page 55

    . A UTO WHITE A OK A UTO WHITE A OPERA TION Result Displa y [A WB] Activating White Detection Fra me Caution : 0 Do not use highly reflective objects, such as metals. Doing so may result in improper white balance adjustment. 0 The Auto White function cannot provide optimum white balance with an object outside the adjustment range, for example when ...

  • JVC GY-HM600E - page 56

    Automatic White Balance Mode (FAW: Fulltime Auto White balance) 0 Press the [WHT BAL] button on the side control panel to enter into Automatic White Balance mode. 0 “<FAW>” appears on the screen. 0 Set the [FULL AUTO] switch on the camera recorder to “ON” to enter Automatic White Balance mode. An appropriate white balance is automatic ...

  • JVC GY-HM600E - page 57

    Audio Recording You can record audio from the two channels (CH1/ CH2) in synchronization with video images on this camera recorder. Select from the four options below to record the audio. 0 Built-in Microphone 0 Microphone connected to [AUX] terminal 0 Microphone connected to [INPUT1] terminal 0 Microphone connected to [INPUT2] terminal . FULL AUT ...

  • JVC GY-HM600E - page 58

    Adjusting Audio Recording Level You can select to adjust the audio recording levels for the two channels (CH1/CH2) manually or automatically. . FULL AUT O ON OFF CH1 INT INPUT1 INPUT2 AUTO MANUAL CH2 L C CH2 CH1 Manual Adjustment Mode (Manual Adjustment) 0 Set the [CH1/CH2 AUTO/MANUAL] switch on the camera recorder to “MANUAL” to enter the manu ...

  • JVC GY-HM600E - page 59

    Monitoring Audio Sound During Recording Using a Headphone You can check the recorded audio using headphone. . AUX MONITOR CH1 BOTH CH2 3 1 2 1 Connect the headphone. 2 Select the channel to monitor with the [MONITOR] selection switch. Setting Description [CH1] Outputs the audio recorded in [CH1]. [BOTH] Outputs the audio recorded in [CH1/CH2]. [CH2 ...

  • JVC GY-HM600E - page 60

    Time Code and User’s Bit Time code and user’s bit data are recorded with the video in this camera recorder. The time code and user’s bit are displayed on the viewfinder and LCD monitor during playback or recording. (Display screen) Displaying Time Code and User’s Bit The time code and user’s bit are displayed on the viewfinder and LCD mon ...

  • JVC GY-HM600E - page 61

    Setting Time Code Generator Presetting the Time Code Time code and user’s bit data generated from the internal time code generator are recorded. This section describes how to set [TC Preset] in the [TC/UB] menu. ( A P97 [ TC Preset ] ) Memo : 0 When [Main Menu] B [System] B [Record Set] B [Record Format] B [Frame & Bit Rate] is set to “50i( ...

  • JVC GY-HM600E - page 62

    2 Set the time code (hour, minute, second, frame). Use the cross-shaped button ( HI ) to place the cursor at the item to set, then use the cross- shaped button ( JK ) to change the values. . During drop frame During non-drop frame Cursor Memo : 0 Press the [OIS/2] button to reset each digit to “0”. The cursor moves to the time digit (left). 3 C ...

  • JVC GY-HM600E - page 63

    Setting Time Code without Opening the Menu . AE LEVEL MENU/THUMB CANCEL MENU/THUMB CANCEL FOCUS ASSIST/1 OIS / 2 TIME CODE Memo : 0 Settings cannot be made in the following cases. 0 [TC/UB] B [TC Generator] has been set to “Regen”. 0 Menu screen is displayed. 0 The camera recorder is not in the Camera mode. Setting Time Code 1 Set [TC/UB] B [TC ...

  • JVC GY-HM600E - page 64

    Synchronizing Time Code on Another Camera This camera recorder is equipped with a time code input/output terminal ([TC] terminal). Connect another camera recorder to the [TC] terminal and synchronize to the time code. 1 Connect the [TC] terminal of the master device with the [TC] terminal of the slave device. Set the [TC IN/OUT] switch of the maste ...

  • JVC GY-HM600E - page 65

    Setting Zebra Pattern When the luminance level range for displaying zebra patterns is specified, diagonal lines (zebra pattern) are displayed at areas with the specified luminance levels during shooting. . A E L E V E L P U S H A U T O ZEBRA/5 1 Set the zebra display pattern. Select the display pattern in [LCD/VF] menu B [Shooting Assist] B [Zebra] ...

  • JVC GY-HM600E - page 66

    Setting Spot Meter The brightness of the object during shooting is displayed. This function is useful when setting video or stage lighting or when specifying camera exposure. A cursor indicating the location and the brightness (%) of that location are displayed in the images shown on the LCD monitor and viewfinder screen. 0 Zebra patterns display t ...

  • JVC GY-HM600E - page 67

    When [Max & Min]/[Max]/[Min] is selected A The cursors appear according to the setting when the button is pressed. Green and yellow frames appear, and the brightness levels of these areas are displayed. . P 13000K P 13000K 1/100 1/100 F1.6 F1.6 0dB 0dB AE+6 AE+6 ND 1/64 ND 1/64 12:34:56 12:34:56 Jan 24,2012 Jan 24,2012 00:00:00.00 00:00:00.00 4 ...

  • JVC GY-HM600E - page 68

    Viewing Recorded Videos Immediately (Clip Review) You can check (review) the last recorded video clip on the screen. However, the video clip cannot be played back if the settings of the camera recorder are different from the video format (Resolution/Frame & Bit Rate/SD Aspect) of the clip. ( A P105 [ Resolution ] ) ( A P106 [ Frame & Bit Ra ...

  • JVC GY-HM600E - page 69

    Memo : 0 Clips cannot be split again for a few seconds after the operation is performed. 0 This item cannot be used when [Slot Mode] is set to “Backup”. ( A P71 [Backup Rec] ) 0 This item cannot be used when [Rec Mode] is set to a value other than “Normal” or “Pre Rec”. ( A P106 [ Rec Mode ] ) 0 The split clips are recorded seamlessly w ...

  • JVC GY-HM600E - page 70

    Memo : 0 During recording in the Dual Rec mode, both the card slot marks light up in red. 0 During recording in the Dual Rec mode to two cards with a different amount of remaining space, if the space of one card runs out, recording to both slots will stop automatically. After recording stops, recording automatically resumes for the card with remain ...

  • JVC GY-HM600E - page 71

    Backup Rec 0 The Backup Rec mode allows you to make use of the media in slot B for backup recording by controlling the starting and stopping of recording in slot B without using the [REC] button. 0 Start or stop the recording using [Main Menu ] B [System] B [Record Set] B [Slot Mode] B [Backup Rec] or press the user button that is assigned with “ ...

  • JVC GY-HM600E - page 72

    3 Start normal recording (normal recording into slot A) 0 Press any of the [REC] buttons. 0 Recording into the media in slot A starts. (The characters “ R REC” appear in red.) 0 The card icon of slot A turns red (unselected state), and the status indicator of slot A blinks in red. . P  13000K 1/ 1 0 0 F1 . 6 0 dB AE + 6 ND 1 / 6 4 12 : 34 : ...

  • JVC GY-HM600E - page 73

    Special Recording Besides the normal recording mode, five special recording methods are available in this camera recorder. They are Pre Rec, Clip Continuous, Frame Rec, Interval Rec and Variable Frame. Select the mode from [Rec Mode] in the [Record Set] menu. Memo : 0 Set using [Main Menu] B [System] B [Record Set] B [Rec Mode]. ( A P106 [ Rec Mode ...

  • JVC GY-HM600E - page 74

    . (Recorded video and audio) Completed Clip Recording 3 Recording 2 Recording 1 Recording 3 Recording 2 Recording 1 (Recording stops) Press and hold [REC] (Recording pauses) Press [REC] (Recording pauses) Press [REC] (Recording resumes) Press [REC] (Recording resumes) Press [REC] (Recording starts) Press [REC] 1 Set “Rec Mode” to “Clip Contin ...

  • JVC GY-HM600E - page 75

    Caution : 0 If the power is cut off due to low battery power, a proper clip may not be generated. 0 When [Format] in the [Main Menu] B [System] B [Record Set] B [Record Format] menu is set to “AVCHD”, Clip Continuous Rec cannot be performed. ( A P105 [ Format ] ) Frame Rec In normal recording, when the recording stops, the image and accompanyin ...

  • JVC GY-HM600E - page 76

    Interval Rec In normal recording, when the recording stops, the image and accompanying data from the start till the end of the recording are recorded as one “clip” on the SD card. In this mode, recording and pause are performed repeatedly at the specified time interval. Only the specified number of frames is recorded. The recording can be writt ...

  • JVC GY-HM600E - page 77

    Variable Frame Rec Shooting in this mode allows you to obtain smooth slow motion or quick motion videos. Using different frame rate settings for recording and playback, videos captured at normal speed can be played back more smoothly than those in low or high speed playback. To enable Variable Frame Rec, the following two settings are required at t ...

  • JVC GY-HM600E - page 78

    Playing Recorded Clips To play back clips recorded on SD cards, switch to the Media mode. Press and hold the [MODE] selection button in Camera mode to enter Media mode. A thumbnail screen of the clips recorded on the SD card is displayed. You can play back the selected clip on the thumbnail screen. Memo : 0 When an SD card without any clips is inse ...

  • JVC GY-HM600E - page 79

    Memo : 0 Clips appended with OK marks cannot be deleted on the camera recorder. 0 When [Format] in the [Main Menu] B [System] B [Record Set] B [Record Format] menu is set to “AVCHD”, the OK mark is protected. ( A P105 [ Format ] ) B Continued From Mark This mark indicates that the current clip is continued from another SD card when recording is ...

  • JVC GY-HM600E - page 80

    Detailed screen * Items that are common with the Standard screen will not be described. Refer to “[Standard screen] P 78”. . C B A A Thumbnail Thumbnail of the clip selected by the cursor. Use the cross-shaped button ( HI ) to move the cursor. B Scroll Mark ( DE ) 0 If there are previous clips, D appears on the left. 0 If there are more clips, ...

  • JVC GY-HM600E - page 81

    Playing back Use the operation buttons on the side control panel of the camera recorder to play back. . AE LEVEL MENU/THUMB CANCEL A C B A IW Button 0 Plays back/pauses the clip pointed by the cursor. 0 You can press the cross-shaped button ( HI ) to perform frame-by-frame forward playback during pause mode. B S / T Button Skips in the reverse or f ...

  • JVC GY-HM600E - page 82

    Deleting Clips Delete clip. . OIS / 2 LOLUX / 3 AE LEVEL MENU/THUMB CANCEL MENU/THUMB CANCEL Memo : 0 Clips appended with OK marks cannot be deleted on the camera recorder. 0 Read-only clips can be deleted on a PC. Deleting One Clip Delete the clip (one clip) pointed by the cursor in [Delete Clips] B [This Clip] in the menu. Memo : 0 Clips with OK ...

  • JVC GY-HM600E - page 83

    Appending/Deleting OK Mark 0 You can append OK marks to the clips for important scenes. 0 Clips appended with OK marks cannot be deleted, thus protecting the important clips. 0 When the camera recorder is in Media mode, you can delete the OK marks appended during recording, or append/delete OK marks after shooting. . AE LEVEL MENU/THUMB CANCEL MENU ...

  • JVC GY-HM600E - page 84

    Selecting and Performing Operations on Multiple Clips 0 Multiple clips can be selected during thumbnail screen or playback screen display. 0 After selecting multiple clips, perform appending/deleting of OK mark, deleting of clips using the action selection screen. 0 After selecting multiple clips, the selections will be canceled by the following op ...

  • JVC GY-HM600E - page 85

    5 Press the Set button ( R ) to confirm the range. 0 The check marks change from magenta to green. 0 Pressing the [LOLUX/3] button while the multiple clips are selected displays the action selection screen. The following operations can be performed. 0 Appends OK mark together: [Add OK Mark] B [Selected Clips] 0 Deletes OK mark together: [Delete OK ...

  • JVC GY-HM600E - page 86

    Basic Operations in Menu Screen 0 Press the [MENU/THUMB] button on the side control panel of the camera recorder or on the LCD monitor to display the menu screen on the LCD monitor and viewfinder. 0 Various settings for shooting and playback can be configured on the menu screen. 0 There are two types of menu screens - [Main Menu] and [Favorites Men ...

  • JVC GY-HM600E - page 87

    Display and Description of the Menu Screen Selecting Menu Items . H I F E B D G A C A Cursor Indicates the selected item. Use the cross- shaped button ( JK ) to move the cursor B Menu Item 0 Displays the names of the menu item and sub-menu. 0 Menu items with [...] after them indicates that there is a sub-menu to access. C Fixed Item Items that cann ...

  • JVC GY-HM600E - page 88

    Text Input with Software Keyboard Use the software keyboard to enter the [Scene File]/[Picture File] subname and [Clip Name Prefix]. [Scene File]/[Picture File] ( A P121 [Configuring Setup Files] ) . G A E H C B D F [Clip Name Prefix] ( A P107 [ Clip Name Prefix ] ) . A E H C B D A Character Entry Field 0 Field for entering the title. 0 You can ent ...

  • JVC GY-HM600E - page 89

    Menu Screen Hierarchical Chart . Reset Process Rev erse Picture Color Gain Adjust... Color Matrix White Balance... WDR Gamma White Clip Knee Black T oe Master Black Adjust... Detail Camera Process... User Switch Set... AE LEVEL SW Handle Zoom Speed GAIN H GAIN M GAIN L Smooth T rans EEI Limit Auto Iris Limit (CLOSE) Auto Iris Limit (OPEN) ALC Limit ...

  • JVC GY-HM600E - page 90

    Camera Function Menu Menu screen for specifying operation settings during shooting. This item can only be selected in the Camera mode. Bars For setting whether to output color bars. [Setting Values: On, R Off] Memo : 0 The audio test signals (1 kHz) can be output simultaneously with the color bar output. ( A P103 [ Test Tone ] ) OIS For setting whe ...

  • JVC GY-HM600E - page 91

    EEI Limit For setting the shutter speed control range when EEI is enabled. [Setting Values: 4F-stop, R 3F-stop, 2F-stop] Smooth Trans For setting the shock reduction function, which slows down the sudden change when switching with the [GAIN] or [WHT BAL] selection switch. [Setting Values: Fast, Middle, Slow, R Off] Memo : 0 However, this function i ...

  • JVC GY-HM600E - page 92

    Spot Meter For specifying the operation when any of the [USER1]-[USER7], [LCD KEY▲], [LCD KEY▶], [LCD KEY▼], or [LCD KEY◀] items is set to “Spot Meter”. ( A P66 [Setting Spot Meter] ) 0 Max & Min: Displays the brightest and darkest areas of the image. 0 Max: Displays the brightest area of the image. 0 Min: Displays the darkest area ...

  • JVC GY-HM600E - page 93

    9 Adjust... For specifying the detailed settings of the contour (detail). ( A P95 [Detail/Adjust Item] ) Memo : 0 This item cannot be selected when [Detail] is set to “Off”. Master Black For adjusting the pedestal level (master black) that serves as the reference black. Increasing the value increases the pedestal. [Setting Values: -50 to +50 ( ...

  • JVC GY-HM600E - page 94

    White Clip For setting the point to apply white clip for input video signals with a high luminance level. 0 108%: Applies white clip at the point where the luminance level is 108 %. 0 100%: Applies white clip at the point where the luminance level is 100 %. Even when this item is set to “108%”, it switches automatically to “100%” if the scr ...

  • JVC GY-HM600E - page 95

    Color Gain For adjusting the video signal color level. Increasing the value deepens the color. [Setting Values: -50 to +15, Off ( R 0)] Memo : 0 Images are displayed in black-and-white when this is set to “Off”. Reverse Picture For recording images correctly by setting this item to “Rotate” when the lens image appears upside down or lateral ...

  • JVC GY-HM600E - page 96

    White Balance Item Preset Temp. For setting the color temperature when the [WHT BAL] switch is set to “PRESET”. For details, refer to “[Adjusting the White Balance] P 53”. Alternative Temp. For setting the alternative color temperature in the Preset mode. When the [WHT BAL] switch is set to “PRESET”, pressing the [ y ] button each time ...

  • JVC GY-HM600E - page 97

    0 Regen: The time code operates in the run mode during recording. When the SD card is replaced, the last time code recorded on the card is read and recorded on a new card so that the time code continues in running order. [Setting Values: Free Run(Ext), Free Run, R Rec Run, Regen] TC Preset For setting the time code (hour, minute, second, frame). Di ...

  • JVC GY-HM600E - page 98

    VF Bright For setting the brightness of the viewfinder screen. Increasing the value increases the brightness. [Setting Values: -10 to +10 ( R 0)] VF Contrast For setting the difference in luminance between the darkest and brightness areas in the viewfinder screen. Increasing the value increases the contrast. [Setting Values: -10 to +10 ( R 0)] LCD ...

  • JVC GY-HM600E - page 99

    Marker Settings Item For setting the marker and safety zone, which are useful in helping you determine the angle of view for the image according to the shooting purpose. ( A P119 [Marker and Safety Zone Displays (Camera Mode Only)] ) Memo : 0 During Clip Review or when in the Media mode, the markers do not appear regardless of the setting. Marker S ...

  • JVC GY-HM600E - page 100

    Media Remain For setting whether to display the remaining space of the recording SD card. [Setting Values: R On, Off] Memo : 0 When the remaining space warning is displayed, the information appears even when “Off” is selected. 0 The displayed time is an estimate. TC/UB For specifying whether to display the time code (TC) or user’s bit (UB) ra ...

  • JVC GY-HM600E - page 101

    A/V Set Menu Menu screen for video output and audio. Video Set... For specifying video output-related settings. ( A P101 [Video Set Item] ) Audio Set... For specifying audio-related settings. ( A P102 [Audio Set Item] ) Video Set Item Display On TV For setting whether to display the display and menu characters on the external monitor. [Setting Valu ...

  • JVC GY-HM600E - page 102

    Audio Set Item Input1 Mic Ref. For setting the reference input level when the [INPUT1] selection switch is set to “MIC” or “MIC +48V”. [Setting Values: -62dB, -56dB, R -50dB, -44dB, -38dB] Input2 Mic Ref. For setting the reference input level when the [INPUT2] selection switch is set to “MIC” or “MIC +48V”. [Setting Values: -62dB, - ...

  • JVC GY-HM600E - page 103

    Test Tone For specifying whether to output the audio test signals (1 kHz) during color bar output. [Setting Values: On, R Off] Mic Wind Cut For selecting whether to cut the low frequencies of the audio input signals (low-cut) when the [INPUT1/ INPUT2] switch is set to “MIC” or “MIC+48V”. Set this item to reduce wind noise from the microphon ...

  • JVC GY-HM600E - page 104

    System Menu This menu screen allows system-related settings. For specifying recording settings, formatting and restoring of SD card, tally lamp setting, date/time, time zone, and other settings. It can also be used to reset the menu settings to their default values. Record Set... For specifying recorded video-related settings. ( A P105 [Record Set ...

  • JVC GY-HM600E - page 105

    Reset All Resets all menu settings. Memo : 0 [Date/Time] and [Time Zone] cannot be reset. ( A P105 [ Date/Time ] ) ( A P105 [ Time Zone ] ) 0 This item is not selectable when recording in Camera mode, during Clip Review, and in Media mode. Date/Time For setting the year, month, day, hour, and minute. Memo : 0 The display order of the date (year, mo ...

  • JVC GY-HM600E - page 106

    9 Frame & Bit Rate For setting the frame rate and encoding bit rate when [System] is set to “HD”. The selectable options vary according to the [Resolution] setting. 0 When “1920x1080” ([Format] is set to “AVCHD”) is selected: [Setting Values: 60i(HQ), 50i(HQ), 60i(SP), 50i(SP)] (Default values: 60i(HQ) (U model), 50i(HQ) (E model)) ...

  • JVC GY-HM600E - page 107

    9 Variable Frame Rate For setting the frame rate during recording when [Rec Mode] is set to “Variable Frame”. The selectable options vary according to the [Resolution] and [Frame & Bit Rate] settings of the [Record Format] menu. ( A P77 [Variable Frame Rec] ) Slot Mode For setting the operation of the card slot. 0 Series: Mode that activate ...

  • JVC GY-HM600E - page 108

    Adding/Editing Frequently Used Menu Items (Favorites Menu) You can select and add/edit frequently used menu items freely to create a personal menu screen (Favorites Menu). Memo : 0 [Favorites Menu] is only enabled in the Camera mode. [Favorites Menu] remains unchanged even when the recording format changes. 0 Up to 20 menu items can be added. 0 Add ...

  • JVC GY-HM600E - page 109

    Editing Favorites Menu You can delete or change the order of the items added to [Favorites Menu]. Deleting Items from [Favorites Menu] 1 Open the [Favorites Menu] screen. A Press the [MENU] button to open the [Main Menu] screen. B Press the [STATUS] button to open the [Favorites Menu] screen. 2 Select [Edit Favorites] and press the Set button ( R ) ...

  • JVC GY-HM600E - page 110

    Changing the Order of Items in [Favorites Menu] . AE LEVEL MENU/THUMB CANCEL FOCUS ASSIST/1 OIS / 2 TIME CODE MENU/THUMB CANCEL DISPLA Y 1 Open the [Favorites Menu] screen. A Press the [MENU] button to open the [Favorites Menu] screen. B Press the [DISPLAY] button to open the [Favorites Menu] screen. 2 Select [Edit Favorites] and press the Set butt ...

  • JVC GY-HM600E - page 111

    6 Press the [FOCUS ASSIST/1] button. The option menu to exit the [Favorites Menu] editing mode appears. 7 Select [Save & Exit] and press the Set button ( R ). . 7 Memo : 0 Moving is not complete until the changes are saved with [Save & Exit]. 0 To exit the editing mode without saving any changes, select [Exit without Saving]. 0 To return to ...

  • JVC GY-HM600E - page 112

    Display Screen in Camera Mode Display 0 screen This screen displays the event. It is also used to display warnings only. . 100min 50min 282m in 12 . 5/ 3 0f ps 0 P  13000K 1/ 1 0 0 F1 . 6 0 dB AE + 6 ND 1 / 6 4 1 00 m in 5 0mi n 2 82 m in P 13000 K 1 / 1 00 F 1 . 6 0 d B AE + 6 ND 1 / 64 ※ 2 ※ 1 A H W D X *1 Appears only during warnings *2 A ...

  • JVC GY-HM600E - page 113

    D Frame rate Displayed as xx/yy (xx: recording frame rate, yy: playback frame rate) only when “Variable Frame” is set in the [Rec Mode] menu. ( A P106 [ Rec Mode ] ) E Resolution Displays the video image resolution. Memo : 0 This item is not displayed when [Main Menu] B [LCD/VF] menu B [Display Settings] B [Record Format] is set to “Off”. ( ...

  • JVC GY-HM600E - page 114

    M Gain 0 Displays the gain value. 0 a is displayed in the ALC mode during Manual shooting. 0 Z is displayed when AE LOCK is set to “ON”. 0 “LUX30” or “LUX36” is displayed when in the low-light shooting mode. Memo : 0 Displayed in the Display 0 screen only when there is a change. N AE Level 0 Appears when the AE function is activated and ...

  • JVC GY-HM600E - page 115

    T Zoom Display 0 Displays the zoom position. (Zoom bar or value) 0 The zoom bar will only be displayed for 3 seconds after the zoom operation is activated. 0 The value will always be displayed. (0 to 99) Memo : 0 You can specify the display method (Number/ Bar) or turn off the display in [Main Menu] B [LCD/VF] menu B [Display Settings] B “Zoom” ...

  • JVC GY-HM600E - page 116

    Display Screen in Media Mode Media Display 0 Screen This screen displays the media status or event. It is also used to display warnings only. . 282m in 0 1000/ 2000 A G H L O M N K 2 82 m in ※ * Appears only during warnings Media Display 1 Screen . 282m in 0 12 : 34 : 56 Jan 24 , 2012 00:00: 00.0 0 1920x1080 60 i H Q 4030 20 10 0 1000/ 2000 A F G ...

  • JVC GY-HM600E - page 117

    H Information Display Use the [AE LOCK/4 ] button to switch between camera information display, GPS display and turning off the display. 0 The GPS display displays information on the recording location of the video being played back only when GPS information has been recorded. 0 Camera information display displays only information of Gain, Iris, Sh ...

  • JVC GY-HM600E - page 118

    Status Screen For checking the settings of the camera recorder. Camera Information Screen For checking information related to shooting using the camera recorder. . USER Switch Set Screen For checking the status (functions assigned) of the user buttons. ( A P36 [Assigning Functions to User Buttons] ) . Audio Screen For checking the settings related ...

  • JVC GY-HM600E - page 119

    Marker and Safety Zone Displays (Camera Mode Only) The marker and safety zone displays are useful in helping you determine the angle of view for the image according to the shooting purpose. 0 Example of display when [Aspect Ratio] = “4:3”, [Aspect Marker] = “Line+Halftone”, and [Center Mark] = “On” . Aspect Marker Center Mark Safety Zon ...

  • JVC GY-HM600E - page 120

    Adjusting Color Matrix 0 The color matrix of the camera recorder can be adjusted to a color of the user’s preference. 0 When shooting is performed using multiple cameras, the colors of the different cameras can be adjusted, and a color of the user’s preference can be set on this camera recorder. 0 The Saturation, Hue and Lightness of the primar ...

  • JVC GY-HM600E - page 121

    Configuring Setup Files The menu settings can be stored on the camera recorder or an SD card by saving them as a setup file. Loading a saved setup file enables you to reproduce the appropriate setup state speedily. Two types of setup files are available. o Scene file: File that contains all menu settings, ranging from video format settings to image ...

  • JVC GY-HM600E - page 122

    6 Select [Store] and press the Set button ( R ). . 6 5 7 Save the file. 0 A confirmation screen appears when you choose to overwrite. Select [Overwrite] on the confirmation screen, and press the Set button ( R ). Saving starts, and “Storing...” appears on the screen. . 7 0 Saving starts, and “Storing...” appears on the screen when the file ...

  • JVC GY-HM600E - page 123

    Deleting Setup Files 1 Display the [Setup File] menu. Select [Main Menu] B [System] B [Setup File] and press the Set button ( R ). ( A P104 [ Setup File ] ) 2 Select [Delete File] and press the Set button ( R ). 3 Select [Scene File] or [Picture File], and press the Set button ( R ). The existing files are displayed. 4 Select the file to delete usi ...

  • JVC GY-HM600E - page 124

    Managing/Editing Clips on a PC Loading Clips to the PC (USB Connection Mode) 0 You can load clips to a PC by connecting the camera recorder to the PC via the USB port. Doing so enables clips stored in the SD card to be managed and edited on the PC. 0 Files on the SD card can be managed/edited on the connected PC in this mode only for USB mass stora ...

  • JVC GY-HM600E - page 125

    When your PC cannot recognize the SD card Confirm and update the OS of your PC. OS Description Windows XP/ Windows XP SP1 Necessary to update to SP2 or higher. Windows XP SP2/ Windows XP SP3 Necessary to download the update software. (KB955704) http://www.microsoft.com/ downloads/details.aspx? familyid=1CBE3906- DDD1-4CA2-B727- C2DFF5E30F61&dis ...

  • JVC GY-HM600E - page 126

    Connecting External Monitor 0 To output live or playback video images and audio sound to an external monitor, select the output signals from the camera recorder, and connect using an appropriate cable according to the monitor to be used. 0 Choose the most suitable terminal according to the monitor in use. 0 [HD/SD SDI] terminal: Outputs either the ...

  • JVC GY-HM600E - page 127

    Connecting the Headphone 0 Audio output from the [ x ] terminal can be selected using [Monitor] in the [A/V Set] menu as well as the [MONITOR] switch on the camera recorder. ( A P103 [ Monitor ] ) 0 The different combinations of settings that are output from the [ x ] terminal and monitor speaker are as follows. [MONITOR] Switch Settings [Monitor] ...

  • JVC GY-HM600E - page 128

    Error Messages and Actions Warning display on the LCD monitor and viewfinder screen, tally lamp indication and warning tone are as follows according to the error status. Memo : 0 This camera recorder makes use of a microcomputer. Noise interference from external sources may prevent it from functioning properly. When this occurs, turn off and on the ...

  • JVC GY-HM600E - page 129

    Error Message Status Action Display Screen Thumbnail Screen Dedicated Screen LOST MEDIA INFO [*] － 0 Card is removed while recording is in progress. 0 Card is removed while formatting is in progress. 0 Card is removed while restoring is in progress. 0 Card is removed while adding the OK mark. 0 Card is removed while writing a setup file. 0 Card i ...

  • JVC GY-HM600E - page 130

    Tally Lamp The tally lamp start blinking when the remaining space on the SD card is running out during recording, or when the battery power is running low. Blinking Mode Remaining Battery Power/SD Card Space Blinks slowly (once every second) 0 Battery power is low 0 Remaining recording time on SD card is less than 3 minutes (during recording) Blink ...

  • JVC GY-HM600E - page 131

    Symptom Action Images on the LCD monitor and viewfinder screen appear dark or blurred. 0 Readjust the brightness of the LCD monitor and viewfinder. 0 Is the [ND FILTER] switch set to “1/64”? 0 Is the iris closed? 0 Is the shutter speed setting too high? 0 Is the amount of peaking too little? Use the [PEAKING +/-] button to adjust the contour fo ...

  • JVC GY-HM600E - page 132

    Specifications General Item Description Power DC 12 V Power consumption Approx. 10.2 W (during recording with backlight set to [STANDARD] while the viewfinder is in use) Mass Approx. 2.4 k g (with battery) Allowable operating temperature 0 °C to 40 °C (32 °F to 104 °F) Allowable operating humidity 30 %RH to 80 %RH Allowable storage temperature ...

  • JVC GY-HM600E - page 133

    Video/Audio Item Description Recording time Approx. 25 minutes (8 GB SD card, 35 Mbps, VBR mode) HD mode (MOV/MP4: MPEG-2) Video recording file format QuickTime File Format (For Final Cut Pro)/MP4 File Format Video HQ mode MPEG-2 Long GOP VBR, 35 Mbps (Max) MP@HL, 1920x1080/59.94i, 29.97p, 23.98p, 50i, 25p 1440x1080/59.94i, 50i 1280x720/59.94p, 29. ...

  • JVC GY-HM600E - page 134

    Dimensional Outline Drawing (Unit: mm) . 269.5 57 345.5 402.5 415.5 178 197 140 156.5 177.5 148.5 (HOOD) * The specifications and appearance of this product are subject to changes for further improvement without prior notice. 134 Others ...

  • JVC GY-HM600E - page 135

    Index A AC adapter .......................................... 27, 28 Action ........................................................ 80 Aspect ratio ................................................ 44 Auto power off ........................................... 29 B Backup rec ................................................ 71 Battery .............. ...

  • JVC GY-HM600E - page 136

    . GY-HM600U/GY-HM600E HD MEMORY CARD CAMERA RECORDER © 2012 JVC KENWOOD Corporation LST 1463-001A ...

Manufacturer JVC Category Camcorder

Documents that we receive from a manufacturer of a JVC GY-HM600E can be divided into several groups. They are, among others:
- JVC technical drawings
- GY-HM600E manuals
- JVC product data sheets
- information booklets
- or energy labels JVC GY-HM600E
All of them are important, but the most important information from the point of view of use of the device are in the user manual JVC GY-HM600E.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals JVC GY-HM600E, service manual, brief instructions and user manuals JVC GY-HM600E. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product JVC GY-HM600E.

Similar manuals

A complete manual for the device JVC GY-HM600E, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use JVC GY-HM600E by users. Manuals are usually written by a technical writer, but in a language understandable to all users of JVC GY-HM600E.

A complete JVC manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual JVC GY-HM600E - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the JVC GY-HM600E, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the JVC GY-HM600E, that we can find in the current document
3. Tips how to use the basic functions of the device JVC GY-HM600E - which should help us in our first steps of using JVC GY-HM600E
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with JVC GY-HM600E
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of JVC GY-HM600E in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning JVC GY-HM600E?

Use the form below

If you did not solve your problem by using a manual JVC GY-HM600E, ask a question using the form below. If a user had a similar problem with JVC GY-HM600E it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)