English dropdown-ico

Manual Lyngdorf Audio RoomPerfect RP-1

40 pages 0.66 mb
Download

Go to site of 40

Summary
  • Lyngdorf Audio RoomPerfect RP-1 - page 1

    Owner´s manual RP-1 RoomPerfect™ MENU MENU ENTER ENTER RP-1 Room Processor ...

  • Lyngdorf Audio RoomPerfect RP-1 - page 2

    2 ...

  • Lyngdorf Audio RoomPerfect RP-1 - page 3

    3 T able of Contents Operating V oltage 4 Unpacking the RP-1 4 Serial Number Registration 4 Introduction 5 Accessories 6 Front Panel 7 Display Indicators 8 Rear Panel 8 Remote Control 10 Connecting the RP-1 12 - Connecting to sources and amplifi ers 12 - Setup options of Main and Line outputs 14 Menu System 15 - Navigating the Menu System 15 Menu ...

  • Lyngdorf Audio RoomPerfect RP-1 - page 4

    4 Operating V oltage The RP-1 can be switched between 115V and 230V mains voltage. In 115V mode the RP-1 requires a mains voltage of 100V -120V at 50-60Hz. In 230V mode the RP-1 requires a mains voltage of 220V -240V at 50-60Hz. The mains voltage setting for your RP-1 can be changed on the rear selector . Make sure the rear selector is in the corre ...

  • Lyngdorf Audio RoomPerfect RP-1 - page 5

    5 Introduction Congratulations on the purchase of your L yngdorf Audio RP-1 with RoomPerfect™. This ‘Black Box’ expands your existing music system with the most advanced room correction system on the market. It is implemented in such a way that you will always achieve the perfect result. No com- puter needed, no acoustic knowledge needed, no ...

  • Lyngdorf Audio RoomPerfect RP-1 - page 6

    6 Owner´s manual RP-1 RoomPerfect™ MENU MENU ENTER ENTER RP-1 Room Processor Accessories Y ou should fi nd the following accessories included: Mains cord 8 m (26.25 feet) XLR – XLR cable Microphone Programming cable Microphone stand with Mic clamp (delivered in a separate carton) Remote control This manual Warnings Warnings CAUTION: RISK OF E ...

  • Lyngdorf Audio RoomPerfect RP-1 - page 7

    7 Front Panel 1 2 3 4 MENU MENU ENTER ENTER RP-1 Room Processor Controls The buttons/controls on the front panel of the RP-1 can all be operated with a direct press. 1. Mains Switch Powers the RP-1 on/off. 2. Display Display with all information on menu system and status. 3. Navigation Keys Pressing the Enter button for 3 seconds will set the RP-1 ...

  • Lyngdorf Audio RoomPerfect RP-1 - page 8

    8 Display Indicators 1 3 2 1. Menu Alphanumeric Display (2*20 Characters). 2. Standby Indicator Power On is indicated with display showing all information on status. Standby mode is indicated with the Standby Indicator being lit only . 3. RoomPerfect Logo Is illuminated whena RoomPerfect fi lter is engaged. Rear Panel 6 4 8 7 2 3 1 5 1. Analog Out ...

  • Lyngdorf Audio RoomPerfect RP-1 - page 9

    9 3. Analog Input Balanced/XLR Left/Right Analog input. Never connect balanced and unbalanced Input at the same time. 4. Analog Input Unbalanced/RCA Left/Right Analog input. The default Input setting is “Balanced / XLR”. This can be changed to “Unbalanced / RCA” from the “Input Connection” menu. If the setting is not set correctly you m ...

  • Lyngdorf Audio RoomPerfect RP-1 - page 10

    10 Remote Control The remote control is used to access the menu system as well as the buttons directly accessible on the front panel. T o control the RP-1 the RCS (Room Correction System) key must be pressed. The functionality of the buttons when RCS is pressed are as follows: 1 2 3 4 5 6 7 digital info analog A/B random repeat AMP channel ENTER vo ...

  • Lyngdorf Audio RoomPerfect RP-1 - page 11

    11 16. V olume Up/down No function. 17. Up / Down / Left / Right In normal operation mode the Up/Down toggles between Bypass, Focus and Global fi lter and the Left/ Right toggles between Neutral and the available voicings. In menu mode they are used for navigation in the menu system. Pressing and holding down the Up/ Down, Right/Left keys, changes ...

  • Lyngdorf Audio RoomPerfect RP-1 - page 12

    12 Connecting the RP-1 The photos used are only meant as visual aids to show the versatility of the RP-1, L yngdorf Audio doesn’t necessarily carry all other products with the described speci- fi cations in the product assortment. Connecting to sources and amplifi ers The RP-1 is very simple to hook up. There are three basic ways to connect the ...

  • Lyngdorf Audio RoomPerfect RP-1 - page 13

    13 3. If your integrated amplifi er or preamp has a ‘tape 2’ loop (sometimes called recording loop) or ‘Pre in/out’: Connect the output of the ‘tape 2’ loop / ‘Pre out’ to the input of the RP-1. • • Then connect the output of the RP-1 to the input of the ‘tape 2’ loop / ‘Pre in’. Using this confi guration enables you t ...

  • Lyngdorf Audio RoomPerfect RP-1 - page 14

    14 Setup options of Main and Line outputs As described in “Routing” and “Crossover Frequency” there are many ways to utilize the Main and Line out- puts. Here we have described the three most common set-up´s. Please note the products, outputs and cross- over frequencies are chosen randomly in these descriptions. Combine them as you see fi ...

  • Lyngdorf Audio RoomPerfect RP-1 - page 15

    15 Menu System The Main Display on the front panel of the RP-1 shows all functionality and current status of the RP-1. An overview of the menu tree can be seen in the ‘Menu T ree’ chapter . Navigating the Menu System Pressing the Menu button on the front panel or the remote enters the menu or steps back one level in the menu system. Use the lef ...

  • Lyngdorf Audio RoomPerfect RP-1 - page 16

    16 Menu T ree This is an overview of the entire RP-1 menu structure. RP-1 Mai n Menu Dis p l ay D i spl a y T i me out D i sp . B r i ght ne ss RoomPer f e c t Guide d s et up Adv a nc e d opt i ons Meas u re Ro om P os Change Fo c us P o s RoomKnow l edge RoomC or r ec ti on Input Connection Input Sensitivity Advanced s e tup Commu ni c a t i o n ...

  • Lyngdorf Audio RoomPerfect RP-1 - page 17

    17 Introduction to RoomPerfect™ Once the guided set-up has been successfully completed you have the option to listen to music through two listening settings; Focus and Global room correction fi lters. T o toggle between the two fi lters and ‘Bypass’ you simply press the Up/Down buttons on the front panel or remote control.They can also be s ...

  • Lyngdorf Audio RoomPerfect RP-1 - page 18

    18 RoomPerfect™ The sub menus accessible in the RoomPerfect™ menu are: Advanced options is only available when Guided set-up has been performed. Guided Setup When you enter the RoomPerfect™ Main Menu for the fi rst time, only the Guided setup is available. Press Enter to initiate the guided set-up. The main steps in the guided set-up procedu ...

  • Lyngdorf Audio RoomPerfect RP-1 - page 19

    19 Setting the Measurement V olume Level When setting the measurement volume level, it is important that you always judge whether the calibra- tion volume is too loud. The calibration volume should not be so loud that it causes: • uncomfortably loud sounds that are inconvenient to you or your environment, or • damage to your loudspeakers. When ...

  • Lyngdorf Audio RoomPerfect RP-1 - page 20

    20 When the message ‘Calibration ok. Press Enter to continue’ is displayed, the calibration volume has suc- cessfully been set and saved. Focus Measurement When the calibration is OK, press Enter to start the measuring process and ‘Measuring Focus position …’ will be displayed. Each measurement comprises four steps: • A low and a high f ...

  • Lyngdorf Audio RoomPerfect RP-1 - page 21

    21 For an optimal room correction it is very important that the measurements are: 1. performed more than 1 meter (approx. 3 feet) away from the loudspeakers, 2. not performed behind the loudspeaker , and 3. that there is at least 50 cm/1.5 ft between each measurement. 50 cm 3. Not behind loudspeaker 1. 2. 1m When a random measuring position and mic ...

  • Lyngdorf Audio RoomPerfect RP-1 - page 22

    22 Calculation of Focus and Global Filters When RoomPerfect™ calculates the fi lters the display shows the following, ‘Calculating fi lters - Please wait’. The fi lter calculation process can be expected to take anywhere between 5 seconds and a minute de- pending on the specifi c task. When RoomPerfect™ has calculated the room correctio ...

  • Lyngdorf Audio RoomPerfect RP-1 - page 23

    23 Advanced Options This section describes the options in the advanced menu, which is available after Guided Setup has been completed. Here you can change the listening position and add more room measurements, check the RoomKnowledge of your current set-up, and check the RoomCorrection for the different fi lters. If the RP-1 is connected before th ...

  • Lyngdorf Audio RoomPerfect RP-1 - page 24

    24 ‘Add more room meas.? Y es/No’ will show in the display: • choose Y es to add another room measurement or , • choose No to stop adding more room measurements. If No is chosen the RP-1 is will return to full scale output. ‘Save room measurement(s)? Y es/No’ will hereafter be shown. • choose Y es to save the performed room measuremen ...

  • Lyngdorf Audio RoomPerfect RP-1 - page 25

    25 Display The sub menus accessible in the Display menu are: Display Di spla y Ti meout Di sp. B r i ght ne ss Display T imeout Di spla y T i meout Display T imeout Display T imeout set-up is used for enabling/disabling the 10 sec. display ’ switch’off’ feature. If enabled the Main Display reading will switch off after 10 sec of inactivity fr ...

  • Lyngdorf Audio RoomPerfect RP-1 - page 26

    26 Input Sensitivity Input Se nsi t iv i ty The Input Sensitivity setting enables you to match the line level output of your pre-amplifi er to the input sensitivity of the L yngdorf Audio RP-1. The normal settings are: Select ‘High’ for input levels <= 2.2V rms and the output/input levels of your pre- and power • amplifi er will match. ? ...

  • Lyngdorf Audio RoomPerfect RP-1 - page 27

    27 Line Out Level This adjusts the overall output level in steps of -0.1 db, it can be attenuated to –40 dB in total. Routing Rout i ng In Routing it is possible to apply different settings to the Main and Line outputs: Symbol Name Main output Line Output R L Highpass fi lter XX R L Lowpass fi lter XX RL LR Left and Right channel switching X - ...

  • Lyngdorf Audio RoomPerfect RP-1 - page 28

    28 Crossover Frequency Crossover Frequency is only available when Routing has been setup. The Crossover Frequency can be selected anywhere between 40 – 9999Hz. It is very diffi cult to give exact guidelines to setting a suitable crossover frequency , fi lter type and order since this depends on the exact drivers and confi gurations. Therefore, ...

  • Lyngdorf Audio RoomPerfect RP-1 - page 29

    29 Delay If you are using a set-up with two main loudspeakers located at an identical distance to the listening position you don’t need to set a delay . However , if the distance isn’t identical and/or you are using a sub- woofer , or a Lyngdorf Audio 2+2 system, you need to set a delay in order to ensure that the sound from each loudspeaker re ...

  • Lyngdorf Audio RoomPerfect RP-1 - page 30

    30 Firmware V ersions The Firmware V ersions menu is used to check the current fi rmware version of your RP-1 and the Room- Perfect™ module as well as the RoomPerfect™ serial number . Factory Reset The Factory Reset setting is used to restore all settings, including RoomPerfect, in the RP-1 to the fac- tory settings. If you return to the facto ...

  • Lyngdorf Audio RoomPerfect RP-1 - page 31

    31 T roubleshooting RoomPerfect™ No microphone connected The error message ‘No microphone connected’ is displayed when no microphone is connected to the RP-1. Solution: • Connect the microphone on the back panel. No signal 1. The error message ‘Fault – No signal’ is displayed when the incoming signal is classifi ed as pure noise. Thi ...

  • Lyngdorf Audio RoomPerfect RP-1 - page 32

    32 T roubleshooting RP-1 Speakers are humming when the RP-1 is turned on Balanced and unbalanced for Main out connections are used at the same time. Solution: • Disconnect the interfering connection. Speakers are humming when the RP-1 is turned on Balanced and unbalanced for Line out connections are used at the same time. Solution: • Disconnect ...

  • Lyngdorf Audio RoomPerfect RP-1 - page 33

    33 Firmware Upgrading The RP-1 fi rmware can be upgraded using the ‘L yngdorf Audio – Serial Load’ software. This is in the PC package available from www .L yngdorf.com. Press the Enter button while powering On to bring the product into upgrade mode. ...

  • Lyngdorf Audio RoomPerfect RP-1 - page 34

    34 Connectors Mains Connector Mains voltage to the RP-1 is applied via an IEC320 type connector . The supplied cable with safety ground should be used to connect the RP-1 to a mains outlet. Make sure the rear selector is in the correct setting and connect the power input only to an appropiate AC source. The warranty will not cover any damage caused ...

  • Lyngdorf Audio RoomPerfect RP-1 - page 35

    35 T echnical Specifi cations Audio Parameter V alue Note Balanced input connectors 3 pin XLR, gold-plated. Case=Gnd, Pin1=Gnd, Pin2=Hot(+), Pin3=Cold(-) Balanced input impedance 10KOhm AC-coupled. Unbalanced input connectors RCA (phono) jack, gold-plated. Case=Gnd, T ip=Hot(+) Unbalanced input impedance 10KOhm AC-coupled Input sensitivity 4.4V (2 ...

  • Lyngdorf Audio RoomPerfect RP-1 - page 36

    36 T echnical Assistance For latest version of the fi rmware, the newest version of this document and ‘Questions and Answers’, please check the ‘Support’ section on the L yngdorf Audio website. If you have any problems with or questions regarding your L yngdorf Audio product, please contact your nearest L yngdorf Audio representative or: L ...

  • Lyngdorf Audio RoomPerfect RP-1 - page 37

    37 Appendix V oicing Curves For further information on the V oicing setting, please refer to the “V oicing” chapter . Music 1 Music 2 Open Open Air Relaxed Soft 10 Hz 100 H z 1k Hz 10kH z -6 -4 -2 0 2 4 6 Fr eq uen cy ( H z) Magni tude (dB) Magnitude R esponse: Music 1 10 Hz 100 H z 1k Hz 10kH z -6 -4 -2 0 2 4 6 Fr eq uen cy ( H z) Magni tude ( ...

  • Lyngdorf Audio RoomPerfect RP-1 - page 38

    38 ...

  • Lyngdorf Audio RoomPerfect RP-1 - page 39

    39 ...

  • Lyngdorf Audio RoomPerfect RP-1 - page 40

    40 www .lyngdorf.com ...

Manufacturer Lyngdorf Audio Category Speaker System

Documents that we receive from a manufacturer of a Lyngdorf Audio RoomPerfect RP-1 can be divided into several groups. They are, among others:
- Lyngdorf Audio technical drawings
- RoomPerfect RP-1 manuals
- Lyngdorf Audio product data sheets
- information booklets
- or energy labels Lyngdorf Audio RoomPerfect RP-1
All of them are important, but the most important information from the point of view of use of the device are in the user manual Lyngdorf Audio RoomPerfect RP-1.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Lyngdorf Audio RoomPerfect RP-1, service manual, brief instructions and user manuals Lyngdorf Audio RoomPerfect RP-1. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Lyngdorf Audio RoomPerfect RP-1.

Similar manuals

A complete manual for the device Lyngdorf Audio RoomPerfect RP-1, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Lyngdorf Audio RoomPerfect RP-1 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Lyngdorf Audio RoomPerfect RP-1.

A complete Lyngdorf Audio manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Lyngdorf Audio RoomPerfect RP-1 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Lyngdorf Audio RoomPerfect RP-1, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Lyngdorf Audio RoomPerfect RP-1, that we can find in the current document
3. Tips how to use the basic functions of the device Lyngdorf Audio RoomPerfect RP-1 - which should help us in our first steps of using Lyngdorf Audio RoomPerfect RP-1
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Lyngdorf Audio RoomPerfect RP-1
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Lyngdorf Audio RoomPerfect RP-1 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Lyngdorf Audio RoomPerfect RP-1?

Use the form below

If you did not solve your problem by using a manual Lyngdorf Audio RoomPerfect RP-1, ask a question using the form below. If a user had a similar problem with Lyngdorf Audio RoomPerfect RP-1 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)